XtendLan SDOMEOAT-57030SD Installation & User Manual

Download

Page 1

SDOMEOAT-57030SD

INSTALLATION & USER MANUAL

for Object Auto Tracking Speed Dome

and Analog High Speed Dome

Page 2

Thank You for Choosing This Intel igent High Speed Dome!

This manual is the Instal ation Guide and Operation Instruction for our Object Auto-Tracking Speed Dome and analog High Speed Dome.

The description of tracking features and operations is applied to Object Auto-Tracking Speed Dome only. The normal analog High Speed Dome DOES NOT has tracking features.

Note: The information contained in the document is subject to change without notice.

Page 3

ii / iii

Table of Contents

1. Safety Notes --- Important!!! .............................................................................................................................1

2. About The Product............................................................................................................................................2

2.1. Features.................................................................................................................................................. 2

2.2. Functions ................................................................................................................................................ 2

2.3. Technical Parameters ............................................................................................................................. 4

3. Installation..........................................................................................................................................................5

3.1. DIP Switch Setting .................................................................................................................................. 5

3.2. Installation..............................................................................................................................................11

3.2.1.

3.2.2.

3.2.3.

3.2.4.

In-ceiling Mount Installatoin ........................................................................................................11

Surface Mount Installation..........................................................................................................13

Wall Mount Installation ...............................................................................................................15

Pipe Pendant Mount Installation.................................................................................................16

4. Operation Guide ..............................................................................................................................................17

4.1. Operation At PowerUp ..........................................................................................................................17

4.2. How To Use Our Control Keyboard.......................................................................................................17

4.2.1.

4.2.2.

4.2.3.

Control Keypad Password And Access ......................................................................................17

Control Keypad Command Syntax .............................................................................................17

Control Keypad Command Types ..............................................................................................18

4.3. Select A Camera....................................................................................................................................18

4.4. Camera Motions.....................................................................................................................................18

4.4.1.

4.4.2.

4.4.3.

4.4.4.

4.4.5.

Pan And Tilt Functions ...............................................................................................................18

Zoom Functions..........................................................................................................................19

Focus Functions .........................................................................................................................19

IRIS Opening Functions .............................................................................................................19

Preset Positions Programming And Recalling ............................................................................20

4.5. Function Program Menu.........................................................................................................................20

4.5.1.

4.5.2.

Porduct Information Menu ..........................................................................................................21

Display Setup .............................................................................................................................21

4.5.2.1. Label Position (Submenu) .................................................................................................22

4.5.3. Main Programming Menu (Dome Settings 1) .............................................................................22

4.5.3.1.

4.5.3.2.

4.5.3.3.

4.5.3.4.

4.5.3.5.

4.5.3.6.

4.5.3.7.

4.5.3.8.

Camera Submenu .............................................................................................................23

Motion Submenu ...............................................................................................................26

Power Up Submenu ..........................................................................................................27

Presets Submenu..............................................................................................................28

Patterns Submenu ............................................................................................................28

Zones Submenu................................................................................................................29

Clear Set Submenu...........................................................................................................30

Preset Number ..................................................................................................................30

4.5.4. Secondary Programming Menu (Dome Settings 2) ....................................................................30

4.5.4.1.

4.5.4.2.

4.5.4.3.

4.5.4.4.

4.5.4.5.

4.5.4.6.

4.5.4.7.

Alarm Submenu ................................................................................................................31

AUX Submenu ..................................................................................................................33

Password Submenu ..........................................................................................................33

Windows Blanking Submenu.............................................................................................34

Heater Setting Submenu...................................................................................................36

Cruise Setting Submenu ...................................................................................................37

Tracking Setting Submenu ................................................................................................37

4.5.5. Dome Label Menu ......................................................................................................................40

4.6. Special Control Panel Commands .........................................................................................................40

5. Trouble Shooting.............................................................................................................................................42

Page 4

3 / 42

1. SAFETYNOTES --- IMPORTANT!!!

The following important notes must be followed carefully to run the PTZ camera and respective accessories in total safety. The camera and relative accessories are called video system in this section.

Use the instructions correctly and fully

Read all safety rules and instructions carefully before starting to run the video system. Follow the instructions in the instruction manual. Pay attention to all warnings on the camera and in the instruction manual.

Keep the safety notes and instructions for use for future reference.

Attachments & Accessories

Do not use attachments other than those recommended in the instruction manual because this could cause risks to the products. Only use the recommended accessories for the camera for installation and operation.

Protect the video system

To protect the camera, avoid installing and using it in direct sunlight or any source of bright light. Bright light, like that from a spotlight, can cause dimming and blurs. A vertical line may appear on the screen. This does not indicate a problem.

Keep it away from rain and dust. Do not touch the zoom lens with your fingers. If needed, use a soft cloth and methylated spirit to remove traces of dust. Apply a specific cap to protect the zoom lens when the camera is not in use.

Install the camera away from video interference. The pictures could present interference if the leads are arranged near a TV set or other device. Either move the leads or re-install the device to solve the problem.

Do not use any part of the video system near water, i.e. bathtubs, wash basins, sinks, tubs, on damp surfaces, near swimming pools, etc. Do not insert objects of any kind through the camera openings to avoid touch live parts: fire and

electrocution risk. Do not pour any kind of liquid on the device. A switch for performing maintenance operations on the camera must be included. Connect the camera only to the

electrical power supply shown on the ratings plate. Contact your retailer if in doubt. Lay the power wires keeping them from being trodden on or squeezed by objects placed on top of them. Pay particular

attention to leads near plugs, screws and the product outlet. Disconnect the power lead and the wiring to protect the camera during electrical storms or when it is left unattended and

not used for a long time. This will prevent damage to the video system in the event of lightening or electrical line overload. Do not overload the electrical power and the extensions to prevent the risk of fire or electrocution.

Do not place the camera near or over radiators or sources of heat. Check that the area is suitably ventilated before installing the camera inside partially closed areas (such as recesses, bookshelves and shelves).

Do not position the camera on unsteady trolleys, stands, brackets or tables. The camera could fall and severely injury adults and children in addition to seriously damaging the product.

Maintenance & Repairs

Always contact a qualified service technician to repair the camera (or any other part of the video system). Unauthorized opening or removing the lids may cause fire and electrocution risk and other dangers.

Disconnect all electrical parts from the mains before cleaning.

Uses spare parts specified by the manufacturer or spare parts with equivalent characteristics when replacements required. Unauthorized replacements can cause fires, electrical shocks and other dangers.

After any servicing intervention or repair to the video system, ask the technician to run a safety check to ensure that everything is working safely.

Damage requiring professional assistance

Disconnect the video system from the power mains and call qualified service personnel in the following cases:

If the power lead or plug is damaged. If liquid or foreign objects accidental y penetrate inside the device. If the device was exposed to rain or water. If the device was dropped, subjected to heavy shocks or if the camera packaging was damaged. If the device performance changes considerably.

Page 5

2 / 42

2. ABOUTTHE PRODUCT

The tracking PTZ is based on our unique motion tracking technology with high position resolution, high speed, low price and selectable communication protocols. It is widely used in surveillance system as unattended CCTV device.

2.1. FEATURES

Auto tracking of moving object (auto PTZ) based on our motion tracking technology. Max 36X optical, 0.0Lux of module specifications. 360º horizontal rotation at maximum speed of 240º /sec. Vertical rotation from -5º to 92º with maximum speed of 160º/sec. Auto panning function with 256 preset positions. Built-in OSD Menu, to change dome parameter, save or call preset, and achieve auto scan, pattern etc. Features password protection to prevent unauthorized changes to the dome setting. Windows blanking and tracking boundary for privacy purpose EasyClip instal ation features The feature of defining specific activity when the dome parks. Integrated design with high reliability. RS-485 data communication. Auto-flip to follow object and surveillance of any subject that is constant and continuous. The speed can be adjusted automatically according to zooming times. Auto focus lens and auto white balance, BLC function. Multi protocol compatible (Pelco-P, Pelco-D, KALATEL, etc). Alarm input, Alarm output, Alarm action.

2.2. FUNCTIONS

Object Tracking

The camera can be manually controlled from the control system by using the controller to pan, tilt and zoom the camera up and down, right and left to follow objects under observation.

In auto tracking mode, the camera can tracking a moving object in the target area with auto pan, tilt and zoom which realizes smart unattended surveillance.

Proportional Pan

Proportional pan automatically reduces or increases the pan and tilt speeds in proportion to the zooming times. At

telephoto zoomsettings, the pan and tilt speedswillbe slower for a given amount of joystickdeflection then at wide zoom

settings. This keeps the image from moving too fast on the monitor when there is a large amount of zoom.

Auto Flip

When the camera tilts downward and goes just beyond the vertical angle, the camera rotates 180º. When the camera rotates (flips), the camera starts moving upward as you continue to hold joystick in the down position. Once you let go of the joystick after the dome rotates, joystick control returns to normal operation. The auto-flip feature is useful for following a person who passes directly beneath the camera.

Save/Call Preset

Preset function is that domesavescurrent horizontal angle and title angle of pan/tilt, zoomand positionparameters into

memory. When necessary dome calls these parameters and adjusts Pan/Tilt and camera to that position. User can save

and call presets easilyand promptlyby using keyboard controlleror infrared controller. The camera supports upto256

presets.

Lens Control

1) Zoom control User can adjust zoom wide or near by controller and get desired image.

2) Focus control System defaults Auto Focus mode, that is, the lens and camera will automatically adjust the focus to get the best image.

Focus can also be controlledmanuallyfrom the controller if required. PressFocus Near or Focus Far key to manually

focus. Focus can be manual via keyboard or matrix, please refer to control keyboard or matrix operation manual for

Page 6

3 / 42

detailed operation. When adjusting position is set with focus status, it goes back to auto focus. The camera will NOT auto focus in the following status.

Target is not in the center of image. Targets are in near and far at the same time. Target is of strong light object. Such as spotlight etc. Target is behind the glass with water drop or dust. Target moves too fast. Large area target such as wall. Target is too dark or vague.

3) IRIS control System defaults Auto IRIS. Camera can adjust immediately according to the alteration of back ground il umination so that a lightness steady image can be achieved.

You may adjust IRIS by controller to get required image brightness. You can call back Auto IRIS by controlling the joystick.

Auto Back Light Compensation

Lens has been divided to six areas for back light compensation (BLC). In a strong light background camera will auto compensate the darker object and adjust light input from the lighter area to avoid a mass image that usually presents a sharp contrast of brightness and darkness.

Auto White Balance

Camera can automatically adjust white balance (WB) according to the alteration of background lightness to give a true color image.

Back Light Compensation (BLC)

If a bright backlight presents, the subjects in the picture may appear dark or as a silhouette. Backlightcompensation

enhances objects in the center of the picture. The camera uses the center of the picture to adjust the IRIS. If there is a bright light source outside this area, it will wash out to white. The camera will adjust the IRIS so that the object in the sensitive area is properly exposed.

Day/Night Function

The IR cut filter of camera module inside the camera can be removed by sending special command, so that the camera can change from color to mono. The picture is clear even if the illumination is as low as 0.01Lux.

This is based on the relative modules. Please refer to technical parameters.

Auto Cruise

The preset position is programmed to be recalled in sequence. This feature is called auto cruise. Up to 54 presets can be saved in each cruise tour.

Patterns

A pattern is a saved, repeating, series of pan, tilt, zoom and preset functions that can be recalled with a command from a controller or automatically by a programmed function (alarm action or park action or power-up action).

Auto, Random and Frame Scan

Auto Scan: Make the camera scan 360º ranging from the current position. Random Scan: Make the camera random scan 360º ranging from the current position. Frame Scan: This feature freezes the scene on the monitor when going to a preset. This allows for smooth transition from one preset scene to another.

Zones Setting

A zone is a pan area, defined by a left and right limit, on the 360º pan plane. The camera has eight zones, each with a 6-character label.

Alarms Input

The camera has four alarm inputs, which can be programmed as high, medium or low priority. When an alarm is received, an input signal to the camera triggers the user-defined action (go to preset, run pattern, etc.) programmed for the alarm.

Auxiliary Output

An auxiliary output is a programmable signal from the camera back box that can trigger another device to operate. An auxiliary output is programmable to trigger from an alarm or from a controller.

Page 7

5 / 42

POS1234

DESCRIPTION

OFF

NANWANG OFFONOFF

OFF

PELCO-P ONONOFF

OFF

PELCO-D OFF

OFFONOFF

KALATEL

COMM PTOL

……

Reserved for future use

POS

DESCRIPTION

567

1200ONOFF

OFF

OFF 2400 OFF

OFF

OFF 4800

OFF

OFF 9600 OFF

OFFONOFF 19200

OFFONOFF

BAUD RATE (BPS)

Reserved for future use

…

3. INSTALLATION

This section contains detailed instructions for installing the camera. These instructions assume that the installer has a good knowledge of installation techniques and is capable of adopting safe installation methods.

3.1. DIP SWITCH SETTING

Before installing the camera drive, check the DIP switches; configure the receiver address, communication protocol, and baud rate setting. Pic. 1 shows switches position and default settings. SW1 switches (1bit) and SW2 switches (1, 2, and 7 bit) are set to the ON position. For normal user, setting switches to default position is enough.

Pic. 1 Switch Position

The camera can be controlled via various communication protocols by setting SW1 switches(1, 2, 3,and 4) and operate at 1200bps, 2400bps, 4800bps, 9600bps and 19200bps baud rate by setting SW1 switches(5, 6, 7, and 8). Refer to Table 3:

SWITCH1 SETTING for communication protocol and baud rate settings, do not set the switches to reserved position. Pic. 2 shows the default settings for the DIP switches.

Pic. 2 Default settings of DIP switches

Please refer to the following tables to set baud rate, and communication protocol type and camera address.

Table 3: SWITCH1 SETTING

Page 8

6 / 42

Address

1234567

OFF

OFFONOFF

OFF

ONONOFF

OFF

OFFONOFF

OFF

OFFONOFF

OFF

OFFONON

OFF

ONONON

OFF

OFFONOFF

OFF

OFFONOFF

OFF

OFF 10

OFFONOFFONOFF

OFF

ONONOFFONOFF

OFF

OFFONON

OFF

OFFONON

OFF

OFFONONONOFF

OFF

ONONONONOFF

OFF

OFFONOFF

OFF

OFFONOFF

OFF

OFFONOFF

OFF

ONONOFF

OFFONOFF

OFF

OFFONOFFONOFF

OFF

OFFONOFFONOFF

OFF

OFFONON

OFFONOFF

OFF

ONONON

OFFONOFF

OFF

OFFONON

OFF

OFFONON

OFF

OFFONOFFONON

OFF

ONONOFFONON

OFF

OFFONONONOFF

OFF

OFFONONONOFF

OFF

OFFONONONON

OFF

ONONONONON

OFF

OFFONOFF

OFF

OFFONOFF

OFF

OFFONOFF

OFF

OFFONOFF

OFF

ONONOFF

OFF

OFFONOFF

OFF

OFFONOFF

OFF

OFFONOFF

OFF

OFFONON

OFF

OFFONOFF

OFF

ONONON

OFF

OFFONOFF

OFF

OFFONOFFONOFF

OFF

OFFONOFFONOFF

OFF

OFFONOFFONOFFONOFF

OFF

ONONOFFONOFFONOFF

OFF

OFFONON

OFFONOFF

OFF

OFFONON

OFFONOFF

OFF

OFFONONONOFFONOFF

OFF

ONONONONOFFONOFF

OFF

OFFONON

OFF

OFFONON

OFF

Page 9

7 / 42

OFFONOFF

OFFONON

OFF

ONONOFF

OFFONON

OFF

OFFONOFFONON

OFF

OFFONOFFONON

OFF

OFFONON

OFF

ONONON

OFFONON

OFF

OFFONONONOFF

OFF

OFFONONONOFF

OFF

OFFONOFFONONONOFF

OFF

ONONOFFONONONOFF

OFF

OFFONONONON

OFF

OFFONONONON

OFF

OFFONONONONONOFF

OFF

ONONONONONONOFF

OFF

OFFONOFF

OFF

OFFONOFF

OFF

OFFONOFF

ONONOFF

OFF

OFFONOFF

OFF

OFFONOFF

OFF

OFFONOFF

OFF

OFFONOFF

OFFONON

OFF

OFFONOFF

ONONON

OFF

OFFONOFF

OFF

OFFONOFF

OFF

OFFONOFF

OFFONOFFONOFF

OFFONOFF

ONONOFFONOFF

OFFONOFF

OFF

OFFONON

OFF

OFFONOFF

OFFONON

OFF

OFFONOFF

OFFONONONOFF

OFFONOFF

ONONONONOFF

OFFONOFF

OFF

OFFONOFFONOFF

OFF

OFFONOFFONOFF

OFFONOFF

OFFONOFFONOFF

ONONOFF

OFFONOFFONOFF

OFF

OFFONOFFONOFFONOFF

OFFONON

OFFONOFFONOFF

ONONON

OFFONOFFONOFF

OFF

OFFONON

OFFONOFF

OFF

OFFONON

OFFONOFF

OFFONOFFONON

OFFONOFF

ONONOFFONON

OFFONOFF

OFF

OFFONONONOFFONOFF

OFFONONONON

OFFONOFF

ONONONONON

OFFONOFF

OFF

OFFONON

OFF

OFFONON

OFF

OFFONOFF

OFF

OFFONON

OFF

ONONOFF

OFF

OFFONON

OFF 100

OFF

OFFONOFF

OFFONON

OFF

Page 10

8 / 42

101ONOFFONOFF

OFFONON

OFF

102

OFFONON

OFF

OFFONON

OFF

103

ONONON

OFF

OFFONON

OFF

104

OFF

OFFONOFFONON

OFF

105

OFF

OFFONOFFONON

OFF

106

OFFONOFFONOFFONON

OFF

107

ONONOFFONOFFONON

OFF

108

OFF

OFFONON

OFF

109

OFFONON

OFF

110

OFFONONONOFFONON

OFF

111

ONONONONOFFONON

OFF

112

OFF

OFFONONONOFF

113

OFF

OFFONONONOFF

114

OFFONOFF

OFFONONONOFF

115

ONONOFF

OFFONONONOFF

116

OFF

OFFONOFFONONONOFF

117

OFFONOFFONONONOFF

118

OFFONON

OFFONONONOFF

119

ONONON

OFFONONONOFF

120

OFF

OFFONONONON

OFF

121

OFF

OFFONONONON

OFF

122

OFFONOFFONONONON

OFF

123

ONONOFFONONONON

OFF

124

OFF

OFFONONONONONOFF

125

OFFONONONONONOFF

126

OFFONONONONONON

OFF

127

ONONONONONONON

OFF

128

OFF

129

OFF

130

OFFONOFF

OFF

131

ONONOFF

OFF

132

OFF

OFFONOFF

OFF

133

OFFONOFF

OFF

134

OFFONON

OFF

135

ONONON

OFF

136

OFF

OFFONOFF

OFF

137

OFF

OFFONOFF

OFF

138

OFFONOFFONOFF

OFF

139

ONONOFFONOFF

OFF

140

OFF

OFFONON

OFF

141

OFFONON

OFF

142

OFFONONONOFF

OFF

143

ONONONONOFF

OFF

144

OFF

OFFONOFF

OFF

145

OFF

OFFONOFF

OFF

146

OFFONOFF

OFF

147

ONONOFF

OFFONOFF

OFF

148

OFF

OFFONOFFONOFF

OFF

149

OFFONOFFONOFF

OFF

150

OFFONON

OFFONOFF

OFF

151

ONONON

OFFONOFF

OFF

Page 11

9 / 42

152

OFF

OFFONON

OFF

153

OFF

OFFONON

OFF

154

OFFONOFFONON

OFF

155

ONONOFFONON

OFF

156

OFF

OFFONONONOFF

OFF

157

OFFONONONOFF

OFF

158

OFFONONONON

OFF

159

ONONONONON

OFF

160

OFF

OFFONOFF

161

OFF

OFFONOFF

162

OFFONOFF

OFF

OFFONOFF

163

ONONOFF

OFF

OFFONOFF

164

OFF

OFFONOFF

165

OFFONOFF

166

OFFONON

OFF

OFFONOFF

167

ONONON

OFF

OFFONOFF

168

OFF

OFFONOFFONOFF

169

OFF

OFFONOFFONOFF

170

OFFONOFFONOFFONOFF

171

ONONOFFONOFFONOFF

172

OFF

OFFONON

OFFONOFF

173

OFFONON

OFFONOFF

174

OFFONONONOFFONOFF

175

ONONONONOFFONOFF

176

OFF

OFFONON

OFF

177

OFF

OFFONON

OFF

178

OFFONOFF

OFFONON

OFF

179

ONONOFF

OFFONON

OFF

180

OFF

OFFONOFFONON

OFF

181

OFFONOFFONON

OFF

182

OFFONON

OFF

183

ONONON

OFFONON

OFF

184

OFF

OFFONONONOFF

185

OFF

OFFONONONOFF

186

OFFONOFFONONONOFF

187

ONONOFFONONONOFF

188

OFF

OFFONONONON

OFF

189

OFFONONONON

OFF

190

OFFONONONONONOFF

191

ONONONONONONOFF

192

OFF

OFFONON

193

OFF

OFFONON

194

OFFONOFF

OFF

OFFONON

195

ONONOFF

OFF

OFFONON

196

OFF

OFFONOFF

OFF

OFFONON

197

OFFONOFF

OFF

OFFONON

198

OFFONON

OFF

OFFONON

199

ONONON

OFF

OFFONON

200

OFF

OFFONOFF

OFFONON

201

OFF

OFFONOFF

OFFONON

202

OFFONOFFONOFF

OFFONON

Page 12

10 / 42

203ONON

OFFONOFF

OFF

204

OFF

OFFONON

OFF

OFFONON

205

OFFONON

OFF

OFFONON

206

OFFONONONOFF

OFFONON

207

ONONONONOFF

OFFONON

208

OFF

OFFONOFFONON

209

OFF

OFFONOFFONON

210

OFFONOFF

OFFONOFFONON

211

ONONOFF

OFFONOFFONON

212

OFF

OFFONOFFONOFFONON

213

OFFONOFFONOFFONON

214

OFFONON

OFFONOFFONON

215

ONONON

OFFONOFFONON

216

OFF

OFFONON

217

OFF

OFFONON

218

OFFONOFFONON

OFFONON

219

ONONOFFONON

OFFONON

220

OFF

OFFONONONOFFONON

221

OFFONONONOFFONON

222

OFFONONONON

OFFONON

223

ONONONONON

OFFONON

224

OFF

OFFONON

225

OFF

OFFONON

226

OFFONOFF

OFF

OFFONON

227

ONONOFF

OFF

OFFONON

228

OFF

OFFONOFF

OFFONON

229

OFFONOFF

OFFONON

230

OFFONON

OFF

OFFONON

231

ONONON

OFF

OFFONON

232

OFF

OFFONOFFONON

233

OFF

OFFONOFFONON

234

OFFONOFFONOFFONON

235

ONONOFFONOFFONON

236

OFF

OFFONON

237

OFFONON

238

OFFONONONOFFONON

239

ONONONONOFFONON

240

OFF

OFFONONONON

241

OFF

OFFONONONON

242

OFFONOFF

OFFONONONON

243

ONONOFF

OFFONONONON

244

OFF

OFFONOFFONONONON

245

OFFONOFFONONONON

246

OFFONON

OFFONONONON

247

ONONON

OFFONONONON

248

OFF

OFFONONONON

249

OFF

OFFONONONON

250

OFFONOFFONONONON

251

ONONOFFONONONON

252

OFF

OFFONONONONONON

253

OFFONONONONONON

Page 13

11 / 42

254

255

OFF ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON

Table 4: SWITCH2 SETTING

Always use the “PELCO P” or “PELCO D” protocols. It is advisable to select PELCO-D protocol at 9600 bps baud rate to ensure the correct operation of the camera

with the compatible products in the catalogue. Do not use address “0” with the “PELCO P” and “PELCO D” protocols.

3.2. INSTALLATION

The camera has four types of mountings: in-ceiling mount, surface mount, wall mount and pipe pendant mount. Please make sure which type you are installing.

3.2.1. IN-CEILING MOUNT INSTALLATOIN

Step 1. Prepare In-ceiling

Pic. 3

Locate the center point of the in-ceilingmountinglocation. Insert the compass tool into the hole. Drawa circle on the

ceiling using the compass tool and a pencil. See Pic. 4 (Left). Cut the circle out of the ceiling tile. See Pic. 4 (Right).

Pic. 4

Step 2. Install back box

Pic. 5

Take out bracket from back box. Insert the back box into ceiling; take out bracket from back box. See Pic. 5.

Install a safety chain/cable (not supplied) that can stand up to 32 pounds(14.6kg). Press the thumb fastener and open the hinged door to the back box. Take out hole of pin. See Pic. 6

Page 14

12 / 42

Pic. 6

Pull cables into the back box through the plastic panel. Connect cables to hole of pin. See Pic. 7

Pic. 7

Insert the hole of pin inside the back box. When finished, close the door to the back box and turn on the power. The LED will light up. See Pic. 8.

Pic. 8

If the LED does not light up, refer to Section 5: Trouble Shooting.

Step 3. Install dome drive

Set the DIP switches for SW1 and SW2 at the bottom of the camera drive for the appropriate receiver address, communication protocol, and baud rate. Refer to the labels on the camera drive or DIP SWITCH SET in this manual.

Remove cover of camera and sponge. See Pic. 9

Pic. 9

Line up link card and faucet of the back board of the dome. Push the dome drive in. See Pic. 10

Page 15

13 / 42

Pic. 10

Step 4. Install lower dome

Pic. 11

Take out a screw from lower dome. Link cables, screw, and lower dome. See Pic. 11.

Pic. 12

Line up the snaps on trim ring with the mounting screws on the back box. Snap the trim ring into the plastic snap washers on the mounting screws. See Pic. 12.

3.2.2. SURFACE MOUNT INSTALLATION

Step 1. Install back board of surface mount

Pic. 13

Locate the back board of the camera location. Drill a hole in the ceiling using a drill. Insert the screw and back board into the hole. See Pic. 13

Pic. 14

Press the thumb fastener and open the hinged door to the back box. Take out hole of pin. See Pic. 15.

Page 16

14 / 42

Pic. 15

Pull cables into the back box into the plastic panel. Connect cables to hole of pin. Insert the hole of pin inside the back board. When finished, close the door to the back board and turn on the power. The LED will light up. See Pic. 15.

If the LED does not light up, refer to Section 5: Trouble Shooting.

Step 2. Install dome drive

Set the DIP switches for SW1 and SW2 on the bottom of the dome drive for the appropriate receiver address, communication protocol, and baud rate. Refer to the labels on the dome drive or DIP SWITCH SET in this manual.

Pic. 16

Line up link card and faucet of the back board of the dome. Push the dome drive in. See Pic. 16.

Step 3. Install dome flange

Pic. 17

Snip a flake piece. Keep three flanges away from two clamps on the back board. See Pic. 17.

Pic. 18

Push the flange of dome into the back board. Take out the membrane on the clarty flake of the dome drive. See Pic. 18.

Page 17

15 / 42

3.2.3. WALL MOUNT INSTALLATION

Step 1. Install the bracket for pendant dome

Pic. 19

When installing outdoors, make sure installation is properly sealed to keep moisture out.

Refer to the instructions supplied with the bracket. Take out cables for the dome through the bracket. See Pic. 19.

Pic. 20

Press the thumb fastener and open the hinged door to the back box. Take out hole of pin. Screw the metal cover into the bracket. See Pic. 20.

Pic. 21

Connect cablesto hole of pin. Insertthe pin inside the back box. Whenfinished, close the door to the back box and turn

on the power. The LED will light up. See Pic. 21.

If the LED does not light up, refer to Section 5: Trouble Shooting.

Step 2. Install dome drive

Pic. 22

Set the DIP switches for SW1 and SW2 at the bottom of the dome drive for the appropriate receiver address, communication protocol, and baud rate. Refer to the labels on the dome drive or DIP SWITCH SET at the beginning of this manual.

Remove cover of camera and sponge. See Pic. 22.

Page 18

16 / 42

Pic. 23

Line up link card and faucet of the back board of the dome. Push the dome drive in. See Pic. 23.

Step 3. Install lower dome.

Pic. 24

Take out a screw from lower dome. Link cables, screw, and lower dome. See Pic. 24.

Pic. 25

Line up the mounting screw holes, and install the two mounting screws. Push the lower dome inside the back box. See Pic. 25.

Pic. 26

Screw the two mounting screws, and screws in the bracket. See Pic. 26.

3.2.4. PIPE PENDANT MOUNT INSTALLATION

See Section 3.2.3 Wall Mount Installation.

Page 19

17 / 42

4. OPERATIONGUIDE

4.1. OPERATION AT POWER UP

The camera employs the default settings the first time it is switched on. Changes to the settings will be permanently

stored and will be made availablethenexttimethe camera is switched on. You can returnto the default settings by

means of the appropriate menu option at any time. The camera will work as follows when it is switched on.

The camera will run a calibration procedure and a message showing the following information will appear on the video output OSD (On Screen Display): protocol, communication parameters, and camera address and software version.

Check that the data are suitable for operation. Otherwise, refer to the section in this document that shows how to install the camera correctly

PROTOCOL: PELCO-D COM: 9600, N, 8, 1

ADDR: 01 SOFTWARE VERSION V4.2

At the end of the calibration step, the camera will switch to stand-by as programmed (POWER UP ACTION in DOME SETTINGS1 > POWER UP). The camera will continue working this way until any command is received from the keypad. The camera during this phase can be pointed to a fixed point or pan across the field. Refer to the detailed described in the

POWER UP ACTION menu section for more details.

4.2. HOW TO USE OUR CONTROL KEYBOARD

The camera is ready to receive commands from our control keyboard (see figure below) after connecting.

4.2.1. CONTROL KEYPAD PASSWORD AND ACCESS

The system will wait for the password to be entered after being switched on. The control panel requires a 6-digit password. The entered digits will be replaced by a “*” symbol on the screen for privacy. Access to the menu is gained after entering all the digits correctly. Refer to the corresponding manual for using the control panel.

The default user password is “111111”. It is advisable to change the default password to prevent intrusions. Do not lose or forget the programmed password. Take note of the new password and keep it in a safe place.

4.2.2. CONTROL KEYPAD COMMAND SYNTAX

Controls can use the joystick, single keys or key combinations. The key command syntax is shown below.

Key command syntax

The syntax used in this manual for controls using keys consists of various elements (words and three digit numbers). Each command is always in braces and each element is separated by commas. Each word or decimal digit used in the syntax is identified by a corresponding key on our control panel. Words can be enclosed in round brackets, square brackets or no brackets. Three digit decimals are never enclosed in brackets.

The following words only can be used: PRESET, CALL, ESC, OPEN, CLOSE, NEAR, FAR, ZOOM OUT, ZOOM IN, CAM, MON, SCAN, ENTER. The decimal digits are: 0, 1, 2, 3, 4, 5, 6, 7, 8, and 9.

Page 20

18 / 42

Some application examples of controls are shown in detail below.

Using the joystick

A command can also be given simply by moving the joystick because this generates actions on the camera or OSD (On Screen Display) menu.

Using a single key

Pressing a single key can cause camera action. For example, the following command will zoom out of the frame. Underling indicates the key is in use.

ZOOM OUT Key combinations

Pressing a key combination in rapid sequence extents the command set. For example, the following command (select camera address 1) is performed by pressing the following keys:

CAM + 1 + ENTER

4.2.3. CONTROL KEYPAD COMMAND TYPES

There are four command types:

Select camera, Move camera (tilt and pan, zoom, adjust focus and IRIS opening, go to preset positions), Adjust camera operation mode using menus, Various quick controls operable from the control panel.

The method for accessing these controls will be shown in detail in the following paragraphs.

4.3. SELECT A CAMERA

The camera to be controlled must be selected first. For example, the following command selects camera 1:

CAM + 1 + ENTER

After this operation, the message CAM 1 will appear on the control panel display.

4.4. CAMERA MOTIONS

After selecting a camera, it can be moved either directly using the control panel as described below:

Panning (horizontal) and tilting (vertical). Zooming, focusing and IRIS opening. Preset positions programming and recalling.

These functions can be directly accessed using a single key or joystick or a simple key combination.

4.4.1. PAN AND TILT FUNCTIONS

The camera may be moved using our keyboard controller. Move the joystick vertically to tilt the camera and horizontally to pan it.

The maximum pan span is from 0º to 360º with continuous rotation. The maximum tilt span is from -5º (camera in vertical position) and 92º.

The panning and tilting speed can be modulated by operating the joystick appropriately.

Note that the maximum speed that can be obtained by operating the joystick is not always equal to that programmed in

the working settings.Thisin factdependson the value of the PROPORTIONALPANsetting in the MOTION menu and the zoom.

If the option is ON, the maximum rotation speed which can be obtained using the joystick is proportional to the magnification used to obtain the best frame.

Panning (horizontal)

Tip the joystick rightwards to turn the camera horizontally clockwise and tip it leftwards to turn it anticlockwise. If no advanced options are set (e.g. range limits set enabled), the camera can be turned continuously without

Page 21

19 / 42

interruptions.

The pan span may be limited between two angles in SETTING1 > MOTION > MANUAL LIMIT.

Tilting (vertical)

Tip the joystick upwards to turn the camera vertically upwards and tip it downwards to turn the camera downwards. The

camera rotation is limited upwards by the horizontal plane or downwards by the vertical axis.

Performance will change considerably near the vertical axis according to whether the AUTO FLIP is on or not (default

setting is on).

WithAUTO FLIP off, the camera will stop in perfectly vertical position and will stop turning when the joystick is tipped

downwards.

WithAUTO FLIP on, the camera will proceed over the vertical axis when the joystick is tipped downwards. This is

because, when the vertical axis is reached, the camera flips automatically by 180 degrees and resumes the initial trajectory.

The AUTO FLIP function can be used to follow a subject arrivingina certaindirection passesunderthe camera and

continues in a straight line. To do this, hold the joystick tipped downwards following the movement of the subject. Observe

that in this case the joystick performance after the camera passes over the vertical axis opposite to the normal axis

because tipping the joystick downwards will turn the camera upwards.

Normal operation of the joystick will be resumed as soon as the downward tip is interrupted (also only for an instant). At

this point, to follow the subject in the same direction, you will need to tip the joystick upwards, as you would normally.

4.4.2. ZOOM FUNCTIONS

The camera frame may be adjusted by using the ZOOM IN and ZOOM OUTcommands. Use ZOOM IN to zoom into the

detail; use ZOOM OUT to zoom out.

Zoom can be set as per the zoom specifications of relative modules, combined between optical zoom and digital zoom.

Refer to the specific section for programming the function.

4.4.3. FOCUS FUNCTIONS

The camera focus may be adjusted manual y using the NEAR and FAR controls.

As the auto focus function is always on, a manual setting made using NEAR and FAR will be kept only until a pan, tilt or

zoom command is used. In this case, auto focus will adjust focus automatically again.

Refer to the specific section for additional details on focusing and on the various options.

The auto focus function cannot work correctly in the following cases:

The object to be focused on it not in the middle of the image. There are far and near object in the frame. Bright light is shining on the subject. The subject is behind a glass pane covered in drops or dust. The subject is moving very quickly. The subject is not well lit. The subject is too big.

4.4.4. IRIS OPENING FUNCTIONS

The IRIS opening may be controlled manually using the OPEN and CLOSE commands.

The manual setting madeusing OPEN and CLOSEwillbe kept onlyuntila pan,tilt or zoomcommandis used if the

automatic IRIS opening option is enabled (the default setting is on). In this case, the opening will be controlling

automatically again.

Refer to the specific section for additional details on IRIS opening adjustment.

Page 22

20 / 42

4.4.5. PRESET POSITIONS PROGRAMMING AND RECALLING

The camera can store up to 256 panning, tilting and zooming configurations (called preset positions) which can be recalled at any time.

The manual focusing and IRIS opening settings cannot be stored.

When storing presets, it is important to remember that some are reserved and cannot be either stored nor used for

positioning the camera.

Presets from 80 to 99 are reserved for management controls Presets from 100 to 103, 170 to 173 are reserved for Tracking and Pattern controls

The following examples show how to program the free Presets and recall them.

Example: programming preset number 32

1) Position the camera in a certain pan, tilt and zoom configuration.

2) Enter the command PRESET + 32 + ENTER. From this moment onwards, simply enter the command CALL + 32 + ENTER to move the camera to the preset

position.

The saved value will be written over if the setting is reprogrammed. The Presets are saved in a permanent memory area of the camera where they are maintained also when power

is disconnected. However, restoring default settings will delete all preset values. Press PRESET + 83 + ENTER to delete all the saved PRESET values. The Presets store the coordinates according to an angular reference system. Therefore, the reference system zero

point may become misaligned with the camera mechanics after prolonged use of the tilting and panning functions. Minor inaccuracies in preset positions may occur. In this case, calibrate the angular coordinate system using the

REBOOT SYSTEM command. This calibration is automatically run when the camera is switched on.

4.5. FUNCTION PROGRAM MENU

Use the following control panel command to access the function programming menu. PRESET + 95 + ENTER

At this point, if no password is required for access, the following first level menu will appear on the screen:

MAIN MENU

< SYSTEM INFORMATION > < DISPLAY SETUP >

< DOME SETTINGS 1>

< DOME SETTINGS 2> <DOME LABEL> RESET CAMERA REBOOT SYSTEM LANGUAGE

ENGLISH

EXIT

Screen 1: Main Menu

Otherwise, if a password is required, the following prompt will appear.

PLEASE INPUT PASSWORD

PASSWORD 1 2 3 4 5 6 7 8 9 0

▲

CLEAR ENTER EXIT

Screen 2: Password Protection

Page 23

21 / 42

Option

Value

Explanation SYSTEM INFORMATION

Product information menu (refer to Section 4.5.1). DISPLAY SETUP

Display menu (refer to Section 4.5.2). DOME SETTINGS 1

Main programming menu (refer to Section 4.5.3). DOME SETTINGS 2

Secondary programming menu (refer to Section 4.5.4).

DOME LABEL

Menu for associating the text to be associated to the camera (refer

Section 4.5.5).

RESET CAMERA

This function reset the device without clearly the settings performed by the user. Resets the camera menu settings, except for the password.

REBOOT SYSTEM

This function restarts the device without clearly the settings performed by the user. The camera is repositioned.

LANGUAGE

ENGLISH

Menus in English.

The password is a numeric combination (max. 4 digits). Select the password digits by moving the joystick in the horizontal direction. Symbol “▲” indicates the digit which will be

entered. Press OPEN to enter the selected digit.

The entered numbers will be replaced by a “*” symbol on the screen for privacy. Select ENTER and press OPEN to access the first level menu after entering all the digits correctly.

THE DEFAULT PASSWORD IS “0000”. It is advisable to change the default password to prevent intrusions.

Do not lose or forget the programmed password. Take note of the new password and keep it in a safe place.

Simply movethe joystick verticallyto scroll the menuandpointthe cursor to the menu item to be selected: at the point,

select OPEN to access the selected second level. Simply press BACK and use OPEN to go back to the previous level menu.

To completely exit a menu on any level, simply select EXIT and use the OPEN command.

Table 5

4.5.1. PORDUCT INFORMATION MENU

In the first level menu, select SYSTEM INFORMATION to display information concerning the protocol, the camera address, the presetting number, the language of use and the measured temperature.

SYSTEM INFORMATION

COM 2400, N, 8, 1 ADDRESS 26

PROTOCOL PELCO-D PRESETS 256 LANGUAGE ENGLISH TEMPERATURE 36°C

SOFTWARE VERSION V4.2 BACK EXIT

Screen 3: System Info

The information in this menu cannot be edited.

4.5.2. DISPLAY SETUP

The DISPLAY SETUP menu is used to enable the labels to be displayed for the various camera functions.

Page 24

22 / 42

Option

Value

Explanation PRESET LABEL

ON/OFF

Show or hide presetting labels (max. 64).

ZONE LABEL

ON/OFF

Show or hide zone labels.

ZOOM

ON/OFF

Show or hide zoom labels.

AZIMUTH/ELEVATION

ON/OFF

Show or hide camera pan/tilt labels. The coordinates refer to the monitor centre.

CAMERA LABEL

ON/OFF

Show or hide camera labels.

LABEL POSITION

Label positioning submenu (refer to Section 4.5.2.1)

DISPLAY SETUP

PRESET LABEL ON

ZONE LABEL ON

ZOOM ON

AZIMUTH/ELEVATION ON

CAMERA LABEL ON

<LABEL POSITION> BACK EXIT

Screen 4: Display Menu

Table 6

4.5.2.1. LABEL POSITION (SUBMENU)

The labels may be positioned where required on the screen.

ZONE CAMERA PRESET

SAVE

RESET

AZIMUTH ZOOM

Screen 5: Label Position

To establish a position:

1) Point the cursor to the label to be moved by moving the joystick vertically.

2) Press OPEN

3) Symbol “■” will appear.

4) Position the entire label in the chosen position using the joystick.

5) Press OPEN.

6) Repeat this operation for each label.

7) Point the cursor “►” to SAVE and press OPEN.

4.5.3. MAIN PROGRAMMING MENU (DOME SETTINGS 1)

In the first level menu, select <DOME SETTINGS 1> and the corresponding submenus to access the main menus.

DOME SETTINGS1

<POWER UP> <PRESETS> <PATTERNS> <ZONE> <CLEAR SET> PRESETS NUMBER BACK EXIT

Screen 6: Dome Settings 1

256

Page 25

Option

Value

Explanation

CAMER

Camera parameter programming submenu (refer to Section 4.5.3.1)

Camera motion parameter programming submenu (refer to Section

4.5.3.2)

MOTION

POWER UP

Power up parameter submenu (refer to Section 4.5.3.3) PRESETS

Preset parameter submenu (refer to Section 4.5.3.4)

PATTERNS

Pattern parameter submenu (refer to Section 4.5.3.5) ZONE

Zone parameter programming submenu (refer to Section 4.5.3.6) CLEAR SET

Clear settings submenu (refer to Section 4.5.3.7) PRESET NUMBER

40/64/256

Maximum number of Presets. Always enter 256 (refer to Section

Option

Value

DIGITAL ZOOM

ON/OFF

BACK LIGHT COMP

ON/OFF

Switch back light compensation ON and OFF. The BACK LIGHT

COMPENSATION function is useful for improving visibility when the

PROGRAM AE MODE

background light is very bright.

OTHERS

Option

Value

Explanation

AE MODE

AUTO

In this mode:

- The shutter opening time cannot be set and is

automatically adjusted.

- Auto IRIS opening is automatically adjusted.

4.5.3.8)

Table 7

4.5.3.1. CAMERASUBMENU

The first level of this menu contains the following options grouped as shown in the following table. To edit the value, simply select the required menu item using the joystick with vertical movements and the OPEN button. Then edit as required. Select BACK/EXIT to close the item.

DIGITAL ZOOM

CAMERA

OFF

BACKLIGHT COMP <PROGRAM AE MODE> <OTHERS> BACK EXIT

OFF

Screen 7: Camera (Sub-Menu)

Automatic exposure submenu (see below)

Table 8

PROGRAM AE CONTROL submenu - Automatic Exposure settings

AE MODE

PROGRAM AE CONTROL

AUTO

LOW LIGHT MODE LOW LIGHT LIMIT IRIS LEVEL AGC LEVEL BRIGHT LEVEL SPOT AE BACK EXIT

AUTO

1/50 F2.0 0DB

0DB/F2.0 OFF

Screen 8: Program AE Control

- Gain control is automatic (AGC ON).

23 / 42

Page 26

24 / 42

SHUTTER

In this mode:

- The shutter opening time may be varied as programmed

in the “LOW LIGHT LIMIT” menu.

- Auto IRIS opening is automatically adjusted.

- Gain control is automatic (AGC ON).

IRIS

In this mode:

- The IRIS opening time is fixed to 1/50 second.

- The auto IRIS opening is manually varied in the “IRIS

LEVEL” menu.

- Gain control is automatic (AGC ON).

MANUAL

In this mode:

- The shutter opening time may be varied as programmed

in the “LOW LIGHT LIMIT” menu.

- The auto IRIS opening is manually varied in the “IRIS

LEVEL” menu.

- AGC gain control is variable as programmed in the “AGC

LEVEL” menu. All items may be accessed in this mode.

BRIGHT

In this mode:

- The IRIS opening time is fixed to 1/50 second.

- The auto IRIS opening is manually varied in the “BRIGHT

LEVEL” menu.

- Gain control is off (0 dB).

LOW LIGHT MODE

AUTO/MANUAL

This parameter is as follows:

- AUTO: uses a fixed maximum IRIS opening (1/50 second).

- MANUAL: increases camera sensitivity to the detriment of

refreshing frequency (frame rate) using the “LOW LIGHT LIMIT” value.

These adjustments are possible only in “MANUAL” or “SHUTTER” mode.

LOW LIGHT LIMIT

1/2, 1/3, 1/6, 1/12, 1/25, 1/50, 1/75, 1/100, 1/120, 1/150, 1/215, 1/300,

1/425, 1/600, 1/1000, 1/1250,

1/1750, 1/2500, 1/3500, 1/6000,

1/10000 OF SECOND

This selects the maximum opening of the IRIS. It is used to manually set the IRIS opening time.

These adjustments are possible only in “MANUAL” or “SHUTTER” mode.

IRIS LEVEL

F2.0, F1.6, F1.4,

OFF, F22, F19, F16, F14, F11, F 9.6, F8.0, F6.8, F5.6, F4.8, F4.0, F3.4, F2.8, F2.4

Manual IRIS adjustment (parameter F). It is used to manually set the IRIS opening time.

These adjustments are possible only in “MANUAL”or “IRIS” mode.

AGC LEVEL

-3DB, 0DB, 2 DB, 4 DB, 6DB, 8 DB, 10 DB, 12 DB, 14 DB, 16 DB, 18 DB, 20 DB, 22 DB, 24 DB, 26 DB, 28 DB

It is possible to automatically control gain (AGC) to one of the indicated values.

This selection is used to manually set the video signal gain.

These adjustments are possible only in “MANUAL” mode.

BRIGHT LEVEL

0DB ~ 26DB

This function adjusts the camera gain and the IRIS opening using a special algorithm which may be programmed by the user. Exposure is controlled by the gain in low light condition and by the IRIS opening in bright light conditions.

The function may be used only if “AE MODE” is set to “BRIGHT”.

SPOT AE

ON/OFF

If this function is on, the adjustments only use the middle part of the image.

Table 9

The following items cannot be accessed in if “AE MODE” is set to “AUTO”:

LOW LIGHT MODE (fixed to “MANUAL”)

Page 27

25 / 42

Option

Value

Explanation

IR SW MODE

AUTO/MANUAL

The opening and closing of the IR filter which adjusts the Day & Night vision of the camera may be controlled in

MANUAL mode. The MANUAL option enables the possibility

to adjust the IR STATUS

parameter

(color/black-and-white). In AUTO mode, the switch is automatic according to the lighting.

IR STATUS

COLOR/BLACK-WHITE

Day & Night camera configuration.

AUTO IRIS

ON/OFF

The auto IRIS may operate automatically (ON) or at a predetermined level in the “IRIS LEVEL” menu. If

enabled manually, this function will remain operative until the camera performs an angular movement of less than 15 degrees. It will switch automatically.

SHARPNESS

ON/OFF

The sharpness of the image may be adjusted automatically (ON) or to a level defined in the

“SHARPNESS LEVEL” menu.

SHARPNESS LEVEL

1 ~ 15

Sharpness can be programmed in the range from 1 and 15 (15 corresponds to maximum sharpness).

ATW

White Balance (WB) is performed in auto tracking mode (Auto Tracking White). This mode automatically balances the white level by analyzing a wide range of colors, i.e. all those with temperatures comprised in the range between 2000K and 10000K.

AUTO

This mode automatically adjusts the white balance by analyzing a more restricted range with respect to the

previous option i.e. those with temperatures in the range from 3000K and 7500K.

OUT

This function automatically balances the whites for outdoor use.

This function automatically balances the whites for indoor use.

AUTO WHITE BALAN

MAN

In this mode, white balancing may be performed by manually selecting the amount of red (R GAIN) and blue (B GAIN).

R GAIN

1 ~ 255

Adjust the red components using these values.

B GAIN

1 ~ 255

Adjust the blue components using these values.

LOW LIGHT LIMIT IRIS LEVEL AGC LEVEL BRIGHT LEVEL

OTHERS sub-menu - Other program settings.

IR SW MODE IR STATUS AUTO IRIS SHARPNESS SHARPNESS

OTHERS

AUTO COLOR ON ON LEVEL 5

AUTO WHITE BALANCE AUTO

R GAIN

B GAIN

BACK EXIT

214 164

Screen 9: Others Sub-Menu

Table 10

Page 28

26 / 42

4.5.3.2. MOTION SUBMENU

MOTION

AUTO FLIP PROPORTIONAL PAN PARK TIME PARK ACTION SCAN SPEED<DEG/S> <SET SCAN> <MANUAL LIMIT> <SET AZIMUTH ZERO> <CLEAR AZIMUTH ZERO> BACK EXIT

ON/OFF

NONE 1

Screen 10: Motion Sub-Menu

Option

Value

Explanation

AUTO FLIP

ON/OFF

When this option is on, the movements of a subject moving underneath the camera can be followed by moving the joystick vertically only. This is possible because after reaching vertical position, the camera will automatical y pan by 180 degrees to be repositioned and resume the tilt stroke.

PROPORTIONAL PAN

ON/OFF

If this mode is active, the pan and tilt speed applied by the keypad is proportion to the set zoom so that the movement

speed decreases when the zoom increases.

PARK TIME

15 S ~ 12 H

With this function, the camera will resume the function defined in ”PARK TIME ACTION” by specifying a value (in 1s, 1m, 1h

steps) following a stop or interruption of the performed function and after the programmed time.

NONE

No action is performed at the end of the park time.

AUTO SCAN

The camera performs an auto scan at the end of the park time: the camera performs a 360 horizontal scan operation.

RANDOM SCAN

The camera performs a random scan at the end of the park time: the camera performs a random 360 degree scan pausing for approximately 2” every 142°.

FRAME SCAN

The camera performs a frame scan at the end of the park time: the horizontal scan is performed in the SET SCAN limits.

PRESET 1/PRESET 8

The camera goes to preset 1 or preset 8 at the end of the park time.

PATTERN 1 ~ 4

The camera performs one of the 4 patterns at the end of the park time (command sequence continuously performed).

CRUISE

The camera performs a cruise (preset sequence) at the end of the park time: the camera runs a cycle of up to 30 preset positions.

REPEAT LAST

The camera simply resumes the operation it was performing before being interrupted at the end of the park time.

PARK TIME ACTION

TRACKING

The camera performs a tracking operation at the end of the park time.

SCAN SPEED <DEG/S>

1 ~ 32 DEG./S

This will specify the rotation speed for automatic horizontal scans.

SET SCAN

This submenu set the limits for horizontal pan movements of the camera. The limits are long applicable in FRAME SCAN mode (see below).

Page 29

27 / 42

MANUAL LIMIT

ON/OFF

If the option is ON, horizontal automatically scanning is performed within the right and left scanning limits open.

To set the left and right scanning limit, position the camera at the required pan angle and press OPEN to set.

The two angles must be at least 10 degrees apart.

A preset position may be called up outside these scanning limits.

SET AZIMUTH ZERO

This sets the pan zero position (see below).

CLEAR AZIMUTH

This is used to delete the zero settings (see below).

Table 11

SET SCAN submenu

This includes a number of settings related to the programming of horizontal FRAME SCAN limits.

1) Press “►” on “SET SCAN STOPS”.

2) Press OPEN to confirm.

3) Go to the required position with the joystick to set the left scanning limit.

4) Press OPEN to confirm.

5) Go to the required position with the joystick to set the right scanning limit.

6) Press OPEN to confirm, Press CLOSE to cancel the operation.

7) Point the cursor “►” to “SET SCAN STOPS” and press OPEN to delete the programmed positions.

SET AZIMUTH ZERO submenu

This includes the settings related to programming of the pan zero position.

1) Go to the required position with the joystick to set zero position.

2) Press OPEN to confirm; Press CLOSE to cancel the operation.

CLEAR AZIMUTH ZERO submenu

This includes the settings related to deleting the pan zero position.

1) Press OPEN to confirm.

2) Press CLOSE to cancel the operation.

4.5.3.3. POWER UP SUBMENU

POWER UP

POWER UP ACTION BACK

EXIT

NONE

Screen 11: Power UP Sub-Menu

Option

Value

Explanation NONE

No action is performed at the end of power up.

AUTO SCAN

The camera performs an auto scan at the end of power up: the

RANDOM SCAN

The camera performs a random scan at the end of power up: the camera performs a random 360° scan pausing for

FRAME SCAN

The camera performs a frame scan at the end of power up:

PRESET 1/ PRESET 8

The camera goes to preset 1 or 8 at the end of power up.

PATTERN 1 ~ 4

The camera performs one of the 4 patterns at the end of

CRUISE

The camera performs a cruise at the end of power up: the

POWER UP ACTION

TRACKING

The camera performs tracking action at the end of power up.

Table 12

Page 30

28 / 42

Option

Value

Explanation

PRESET NUMBER

1-64

This option is used to select a presetting for entering a descriptive label. This operation is allowed for up to 64 Presets.

Press the OPEN button and use the joystick to set the number of the presetting to the stored. Press OPEN to confirm.

EDIT PRESET LABEL

This submenu is used to access writing mode for associating a label to a presetting (see below).

EDIT PRESETSCENE

This submenu is used to store the Presets.

CLEAR PRESET

The submenu is used to delete the presetting descriptions.

4.5.3.4. PRESETS SUBMENU

PRESETS

PRESET NUMBER

…PRESET NOT DEFINED…

<EDIT PRESET LABEL> <EDIT PRESET SCENE> <CLEAR PRESET> BACK EXIT

Screen 12: Presets

Table 13

The camera will start a scanning cycle when a presetting or pattern is recalled. This scanning cycle may be interrupted simply by moving the joystick.

EDIT PRESET LABEL submenu

This includes the operations needed for associating a label to a presetting.

1) Use the joystick to point the cursor to ”EDIT PRESET LABEL” option.

2) Press OPEN. The following menu will appear on the display:

PRESET NUMBER 1

PRESET LABEL 1 - - - - 0 1 2 3 4 5 6 7 8 9 Y Z y z

A B C D E F G H I J K L M N O P Q R S T U V W X

a b c d e f g h I j k l m n o p q r s t u v w x

OK CANCEL

SPACE BACKSPACE`

Screen 13: Preset Label Sub-Menu

3) Point the cursor to the first character to the use and press OPEN. Point the cursor to “BACKSPACE” to delete it.

4) After writing the text, point the cursor to OK and press OPEN to save and go back to the main screen.

4.5.3.5. PATTERNS SUBMENU

PATTERNS

PATTERN NUMBER 1 <PROGRAM PATTERN>

<CLEAR PATTERN> BACK EXIT

Screen 14: Patterns Sub-Menu

A pattern is a sequence of movements and functions which may be stored and repeated manually or automatically.

Page 31

29 / 42

Option

Value

Explanation PATTERN NUMBER

1 ~ 4

This option is used to select a pattern.

PROGRAM PATTERN

This submenu is used to program a pattern (see below)

CLEAR PATTERN

This submenu is used to delete a pattern (see below)

Option

Value

Explanation

ZONE NUMBER

1 ~ 8

This option is used to select a zone. Press the OPEN button and use the joystick to set the required

zone number. Press OPEN to confirm.

EDIT ZONE LABEL

This submenu is used to associate a label to a zone (see below).

EDIT ZONE

This submenu is used to create a zone (see below).

ZONE ENABLED

ON/OFF

This is used to enable/disable each zone selected in the “ZONE NUMBER” field.

CLEAR ZONE

This submenu is used to delete the zone selected in the “ZONE NUMBER” field (see below).

Table 14

PROGRAM PATTERN submenu

This includes all the operations needed to program a pattern.

1) Use the joystick to point the cursor to the ”PATTERN NUMBER” option.

2) Select the required pattern and press OPEN.

3) Position the cursor under ”PROGRAM PATTERN” option and press the OPEN button. The number of actions available (including zoom operations) for programming the Pattern is shown in percentage form on

the screen while they are each being programmed. 100 operations are available for each pattern.

CLEAR PATTERN submenu

This includes the operations for deleting the selected pattern.

4.5.3.6. ZONES SUBMENU

ZONE NUMBER

ZONES

…ZONE NOT DEFINED…

<EDIT ZONE LABEL> <EDIT ZONE> ZONE ENABLED

<CLEAR ZONE > BACK

EXIT

Screen 15: ZONES Sub-Menu

A zone is a space defined on the display by the user. It may be associated to a label. Up to 8 zones may be defined.

Table 15

EDIT ZONE LABEL submenu

This includes the operations needed to enter labels to be associated to zones.

1) Use the joystick to point the cursor to the ”EDIT ZONE LABEL” option.

2) Press OPEN. The following menu will appear on the display:

Page 32

30 / 42

Option

Value

Explanation CLEAR ZONES

This option is used to delete all the zone settings.

CLEAR PRESETS

This is used to delete all the Presets.

CLEAR PATTERNS

This is used to delete all the pattern settings.

RESTORE FACTORY DEFAULTS

This performs a total reset and loads the default settings. The operations may take a few seconds (approximately 20 seconds): the message “WAIT” will appear on the monitor.

ZONE NUMBER 1

ZONE LABEL 1 - - - - 0 1 2 3 4 5 6 7 8 9 Y Z y z

A B C D E F G H I J K L M N O P Q R S T U V W X

a b c d e f g h I j k l m n o p q r s t u v w

OK CANCEL SPACE BACKSPACE

Screen 16: Zone Label Sub-Menu

3) Point the cursor to the first character to be used and press OPEN. Point the cursor to “BACKSPACE” to delete it.

4) After writing the text, point the cursor to OK and press OPEN to save and go back to the main screen.

EDIT ZONE submenu

This includes all the operations needed to program a zone.

1) Press “►” on “EDIT ZONE”.

2) Press OPEN to confirm.

3) Use the joystick to point to the required position to define the left limit of the zone to be created.

4) Press OPEN to confirm.

5) Use the joystick to point to the required position to define the right limit of the zone to be created.

6) Press OPEN to confirm.

7) Press CLOSE to cancel the operation.

CLEAR ZONE submenus

This includes the operations for deleting the selected zone.

4.5.3.7. CLEAR SET SUBMENU

CLEAR

CLEAR ZONES CLEAR PRESETS

CLEAR PATTERNS RESTORE FACTORY DEFAULTS BACK

EXIT

Screen 17: Clear Set Sub-Menu

This menu is used to delete the settings of several elements at one time.

Table 16

4.5.3.8. PRESET NUMBER

This option can be used to set the number of Presets which may be used.

1) Point the cursor to “►” “PRESET NUMBER”.

2) Press ENTER.

3) Move the joystick vertically and select “256”.

4) Press ENTER to confirm.

Do not change the setting (“256”).

4.5.4. SECONDARY PROGRAMMING MENU (DOME SETTINGS 2)

In the first level menu, select <DOME SETTINGS 2> and the corresponding submenus to access the other menus.

Page 33

31 / 42

Option

Value

Explanation ALARMS

Alarm submenu (refer to Section 4.5.4.1) AUX

Alarm output submenu (refer to Section 4.5.4.2) PASSWORD

Password submenu (refer to Section 4.5.4.3) WINDOWS BLANKING

Privacy zones submenu (refer to Section 4.5.4.4) HEATER SETTING

Heater use submenu (refer to Section 4.5.4.5) CRUISE SETTING

Cruise programming submenu (refer to Section 4.5.4.6)

TRACKINGSETTING

Automatic tracking submenu (refer to Section 4.5.4.7)

Option

Value

Explanation ALARM NUMBER

1 ~ 4

This option allows selecting one of the 4 alarm inputs.

SEQUENCE (SECS)

1 ~ 250

Duration time (in seconds) of the action related to each alarm when several alarms occur at the same time.

ALARM SETTINGS

This submenu contains the alarm management programming (see below).

CLEAR SETTINGS

This submenu is used to delete the alarm programming (see below).

DOME SETTINGS 2

<PASSWORD> <WINDOWS BLANKING> <HEATER SETTING> <CRUISE SETTING> <TRACKING SETTING> BACK EXIT

Screen 18: Dome Settings 2

Table 17

4.5.4.1. ALARM SUBMENU

ALARMS

ALARM NUMBER 1 SEQUENCE(SECS) 1

<ALARM SETTINGS> <CLEAR SET> BACK EXIT

Screen 19: Alarms Sub-Menu

The camera has 4 alarm inputs and 2 alarm outputs. The actions defined by the user may be associated to an alarm.

Table 18

ALARM SETTINGS submenus

This includes the operations needed to program the alarms.

Page 34

32 / 42

Option

Value

Explanation ALARM NUMBER

1 ~ 4

This option allows selecting one of the 4 alarm inputs.

NONE

No action occurs during the alarm.

PRESET

The camera goes to the corresponding presetting following

the alarm (correspondence is fixed: Alarm 1 - Preset 1; Alarm

2 - Preset 2, etc.).

PATTERN

The alarm performs the corresponding pattern following the alarm (correspondenceis fixed: Alarm 1 - Pattern 1; Alarm 2 -

Pattern 2; etc.)

AUTO SCAN

The camera performs an auto scan after the alarm: the camera performs a 360 horizontal scan operation.

RANDOM SCAN

The camera performs a random scan after the alarm: the camera performs a random 360° scan pausing for approximately 2” every 142°.

FRAME SCAN

The camera performs a frame scan after the alarm: the horizontal scan is performed in the SET SCAN limits.

CRUISE

The camera performs a cruise after the alarm: the camera runs a cycle of up to 30 preset positions.

ALARMACTION

TRACKING

The camera performs a tracking operation after the alarm, starting from the preset position associated with the alarm.

OFF

No action occurs after the alarm.

AUX1

AUX1 output is activated following the alarm: e.g. a siren.

ALARM AUX

AUX2

AUX2 output is activated following the alarm: e.g. a blinker.

ALARM CONTACT

ON/OFF

Alarm output polarity: normally open (ON) or normally closed (OFF).

The circuit will open to generate an alarm if it is “NC” and will close if it is “NO”.

ALARM NUMBER

ALARM ACTION ACTIVATE AUX

ALARM CONTACT BACK

EXIT

1 NONE OFF OFF

Screen 20: Alarm Settings

Table 19

If an alarm is triggered during any automatic operation of the camera (Pattern, Auto Tracking, etc.), the operation

in progress is stopped and the camera executes the action that has been set in the ALARM ACTION menu:

In the event of Preset action, the camera moves to the preset position. Then, if the option PARK TIME ACTION is set to execute an action, the action will be executed after the PARK TIME period has expired.

In the event of "TRACKING" action, the camera executes the tracking function starting from the preset

position that has beenassociatedwith the alarm. Once the tracking actionhas finished, the camera

executes the action set in the option PARK TIME ACTION. In the event of "PATTERN, AUTO SCAN, RANDOM SCAN, FRAME SCAN, CRUISE" actions, the action is

executed by the camerapermanentlyand can only be stopped by one of the following actions:any

command sent by the operator, the 6+use of the joystick, any alarm event.

Page 35

33 / 42

Option

Value

Explanation DWELL TIME 1

0 ~ 30

Time (in seconds) of activation of the AUX1 output

DWELL TIME2

0 ~ 30

Time (in seconds) of activation of the AUX2 output

Option

Value

Explanation ENABLE PASSWORD

ON/OFF

This enables the password.

EDIT PASSWORD

This is the password entry procedure.

4.5.4.2. AUX SUBMENU

AUX

DWELL TIME<SECS> 1 0 DWELL TIME<SECS> 2 0

BACK EXIT

Screen 21: AUX Sub-Menu

The camera has 2 alarm outputs (AUX1 and AUX2) which may be programmed to activate the external devices in the case of alarm. The 2 outputs closed to ground.

Table 20

4.5.4.3. PASSWORD SUBMENU

PASSWORD

ENABLE PASSWORD <EDIT PASSWORD>

BACK EXIT

OFF

Screen 22: Password Sub-Menu

Table 21

The password is a numeric combination (max. 10 digits).

THE DEFAULT PASSWORD IS “0000”. It is advisable to change the default password to prevent intrusions. Do not lose or forget the programmed password. Take note of the new password and keep it in a safe place.

INPUT OLD PASSWORD PASSWORD

1 2 3 4 5 6 7 8 9 0 CLEAR

ENTER BACK

Screen 23: Edit Password

1) Select the password digits by moving the joystick in the horizontal direction. Symbol “▲” indicates the digit which will be entered.

2) Press OPEN to enter the selected digit.

3) The entered numbers will be replaced by a “*” symbol on the screen for privacy.

4) Enter all the digits correctly and select ENTER to confirm.

5) During the password changeprocedure you willbeaskedto entertheoldpassword. Enter the new passwordand

enter it again for confirmation.

Page 36

34 / 42

Option

Value

Explanation

STYLE

GRAY/SMEAR

There are two ways to blank out the zone to be masked: either using a grey window which entirely conceals the area or by using a semi-transparent smear window which shows the scene without details.

BLANK ALL ABOVE

Blanks out the upper part of the frame shown on the monitor.

BLANK ALLBELOW

Blanks out the lower part of the frame shown on the monitor.

SET WINDOWS

The submenu is used to position and configure the privacy zones (see below).

SET MASK COLOR

1 ~ 13

This is used to select the blanking window color:

0 → black 1 ~ 6 → grey (1 dark; 6 light)

7 → white 8 → red 9 → green 10 → blue 11 → cyan 12 → yellow 13 → magenta

4.5.4.4. WINDOWS BLANKING SUBMENU

Windows blanking is only available for Sony Modules at present.

WINDOWS BLANKING

STYLE GRAY

BLANK ALL ABOVE BALANK ALL BELOW <SET WINDOWS> SET MASK COLOR BACK EXIT

OFF OFF

Screen 24: Windows Blanking

The camera can be used to define up to eight privacy zones which blank out certain areas of the screen concealing them from the operator’s sight.

A privacy zone appears as a grey or black rectangle associated to a certain pan, tilt and zoom position of a camera. This association is used to move, expand and compress the rectangle according to how the pan, tilt or zoom settings are changed.

Table 22

The two blanking bands (upper & lower) may coexist at the same time. The two blanking bands (upper & lower) cannot coexist at the same time in presence of a privacy zone. A band will automatically be removed if both bands are enabled and a privacy zone is activated. If an attempt to activate a blanking band is attempted with a privacy zone active, the privacy zone will remain

active to the detriment of the blank.

Blanking parameters

BLANK ALL ABOVE

BLANK ALL BELOW

OFF

No blanking

OFF

No blanking 0

-5º~10º

5º~92º 10

-5º~25º

-5º~92º 20

-5º~35º

5º~92º 30

-5º~45º

15º~92º

Page 37

35 / 42

-5º~55º

25º~92º

-5º~65º

35º~92º

-5º~75º

45º~92º

-5º~85º

55º~92º

-5º~95º

70º~92º

Option

Value

Explanation WINDOWS NUMBER

1~ 8

This option is used to select one of the 8 privacy zones (WINDOWS).

EDIT WINDOW LOCATION

This option is used to activate the privacy zone positioning procedure (see below).

EDIT WINDOW ZOOM

This option sets the zoom level over which the created privacy zone will be visible.

ENABLE WINDOW

ON/OFF

This switches the privacy zone selected in WINDOWS NUMBER on and off.

CLEAR WINDOW

This deletes the privacy zone selected in WINDOWSNUMBER.

Table 23

The coordinates shown on the monitor refer to the central point of the monitor (where the diagonals meet).

SET WINDOWS submenu

This includes the operations needed to position and configure the privacy zones.

SET WINDOWS

WINDOWS NUMBER <EDIT WINDOW LOCATION>

<EDIT WINDOW ZOOM > ENABLE WINDOW CLEAR WINDOW BACK EXIT

Screen 25: Set Windows Sub-Menu

OFF

Table 24

EDIT WINDOW LOCATION submenu

This menu may be used to define the position of the privacy zones to be created.

1) Press “►” on “EDIT WINDOW LOCATION”.

2) Press OPEN. The following screen will appear.

EDIT WINDOWS LOCATION

IRIS OPEN TO CONTINUE IRIS CLOSE TO CANCEL

Screen 26: Edit Windows Location Sub-Menu

3) A cross-shaped pointer will appear on the monitor: this pointer will correspond to the middle of the privacy zones being created.

4) Point the cross-shaped cursor to the required position by moving the joystick in the vertical and horizontal directions.

5) Press OPEN. A square will appear on the monitor (with the previously defined features).

6) Use the joystick to obtain the required dimensions of the privacy zone: a) move leftwards to increase the left and right edges of the blanking zone b) move rightwards to decrease the left and right edges of the blanking zone c) move upwards to increase the upper and lower edges of the blanking zone d) move downwards to decrease the upper and lower edges of the blanking zone

7) Press OPEN to confirm after reaching the required dimensions.

8) At this point, either select a new privacy zone or select CLOSE to quit the menu.

It is preferable to set the privacy zones with a zoom level of 1x.

Page 38

36 / 42

Option

Value

Explanation

HEATER DISPLAY

ON/OFF

This switches the heater status display on and off. The message “HEATER” will appear when the heater is on.

AUTO

Heater operating mode: when set to ”AUTO”, the heater is operated when the outside temperature is lower than the setting made in the following menu.

OFF

The heater is always off.

HEATER MODE

The heater is always on.

TEMPERATURE SET

-99 ~ +99

Temperature threshold in °C under which the heater is activated. Recommended values 18 - 20 °C

Remarks on Privacy Zones

Privacy zones can be programmed (and therefore the menu can be opened) in optical zoom

situations only. The privacy zone works also in digital zoom conditions.

The privacy zone rectangle will move on the screen when panning and tilting. Zooming will expand

and contract the rectangle.

The rectangle will expandtwicein thevertical direction and four times in the horizontal position

avoid viewing protected areas when panning, tilting and zooming.

After panning and tilting,theprivacy zonerectanglewill shift and return to the correct

dimensions.

After zooming, the rectangle will remain either contracted or expanded according to the applied zoom (regardless of the x2 or x4 factor applied while zooming).

It is advisable to make the privacy areas slightly larger than the area to be concealed. Privacy zones can only be rectangular or squares, but several rectangles can be placed to mask the

area as required.

EDIT WINDOW ZOOM submenu

This menu item may be used to define the zoom level at which the privacy zone becomes visible after defining the color and the position of the privacy zone.

1) Press “►” on “EDIT WINDOW LOCATION”.

2) Press OPEN, the following screen will appear.

EDIT WINDOWS

IRIS OPEN TO CONTINUE

IRIS CLOSE TO CANCEL

Screen 27: Edit Windows

3) Press OPEN and start the zoom setting procedure.

4) The newly created privacy zone will appear on the monitor.

5) Use the joystick to obtain the required zoom level over which the privacy zone will become visible: a) Turn clockwise to increase the zoom level b) Turn anticlockwise to decrease the zoom level

6) Press OPEN to confirm.

4.5.4.5. HEATER SETTING SUBMENU

HEATER SETTING

HEATER DISPLAY HEATER MODE TEMPERATURE SET BACK

EXIT

ON AUTO

℃

Screen 28: Heater Setting

Table 25

Page 39

37 / 42

4.5.4.6. CRUISE SETTING SUBMENU

CRUISE

DWELL TIME<SECS> PRESET LIST

1 ON

1 2 3 4 5 6 7 8 9 0

0 1 1 0 0 1 0 1 1 1

BACK EXIT

0 OFF

Screen 29: Cruise

The CRUISE function is used to make the camera run a cycle consisting of up to 30 preset positions. This menu item is used to enable each of the preset positions used in the cruise cycle.

For the cruise cycle to be effective, the preset positions must be actually stored.

Option

Value

Explanation DWELL TIME <SECS>

5 ~ 250

Duration (in seconds) of the dwel ing time on each presetting.

PRESET LIST

1 ~ 3

Value 1 selects the first group of Presets from 1 to 10, value 2 selects the second group from 11 to 20, value 3 the third group from 21 to 30.

The following 10 digits (1/10) are used to switch the corresponding preset in the corresponding ten (1-10, 11-20,

21-30) either on or off (1=ON; 0=OFF).

Table 26

4.5.4.7. TRACKING SETTING SUBMENU

TRACKING SETTING

DEFAULT SETTING SIZE SENS

GRAY SENS LOST ACT ZOOM SETTING WAIT TIME<S> <TRACKING BOUNDARY> AUX TRACKING SPEED

TRACKING TIME<M> AUTO

BACK EXIT

MEDIUM MEDIUM

TO HOME&TRACKING

ON 40

OFF

AUTO

Screen 30: Tracking Setting Sub-Menu

Operating function

The auto tracking function is used to automatically track moving objects by detecting grayscale variations in the frame.

Option

Value

Explanation DEFAULT SETTING

This function is used to load the auto tracking default settings.

SIZE SENS

LARGE/MEDIUM/SMA LL

This option defines the total dimensions of the object to be tracked. The parameters are LARGE/MEDIUM/SMALL. A object larger than one fourth of the screen is LARGE. An object smaller than one eighth of the screen is SMALL.

GRAY SENS HIGH/MEDIUM/LOW

This option determines the auto tracking sensitivity. The sensitivity measures the grey scale variations of a certain point in the frame in the unit of time.

Page 40

38 / 42

RETURN HOME & TRACKING

This option is used to establish the action to be performed if the camera looses the tracked object: the RETURN HOME

AND TRACKING option repositions the camera in the original position (i.e. the position the camera goes to after power up) and tracking is enabled from this position.

KEEP TRACKING

The KEEP TRACKING option keeps the camera in the position reached and the tracking function is kept on waiting for an object to be intercepted again.

LOST ACT

STOP TRACKING

The STOP TRACKING option leaves the camera in the position reached and deactivates the tracking function.

ZOOM SETTING

OFF, 1 ~ 18

This option determines the maximum zoom value that the camera / may use for tracking the object.

WAIT TIME

5, 10, 15, 20, 25, 30, 35, 40 SECONDS

This option determines the time which must elapse before performing an action after loosing a motion in frame. The

action (LOST ACT) may consist in:

- The camera goes to the original position (i.e. the

position the cameragoesto after power up) and

tracking is enabled from this position (RETURN HOME AND TRACKING).

- The camera is left in the position reached and the

tracking function is kept on waiting for an object to be intercepted again (KEEP TRACKING). The camera is left in the position reached and deactivates the tracking function (STOP TRACKING).

TRACKING BOUNDARY

UP/DOWN/LEFT/RIGHT

This option is used to define the zone in which the camera performs the tracking.

AUX

OFF, 1, 2

This option is used to activate one of the 2 alarm outputs if the tracking function is on (OFF= no active alarm output).

TRACKING SPEED

AUTO, 1 ~ 63

This option establishes the camera movement speed. If AUTO is selected, the camera is automatically “adapted” to the motion of the target. The MANUAL options allow selecting the expected speed of the object to be tracked (1 slow, 63 fast).

TRACKING TIME

AUTO,1~15 (MINUTES)

This option allows setting the max. tracking duration, in minutes, during which the camera automatically tracks moving objects.

Once the tracking time has expired, the camera executes the action set in the option "LOSTACT", independently of

the movement in the scene. If the value "AUTO" is set, there is no time limitation on the

tracking action and, in case of no movement in the scene at all, the camera executes the option "WAIT TIME".

Table 27

TRACKING BOUNDARY submenu

Operations needed to establish an intervention zone for the tracking function.

TRACKING BOUNDARY

BOUNDARY LIMIT CLEAR BOUNDARY LEFT LIMIT

RIGHT LIMIT UP LIMIT DOWN LIMIT BACK

EXIT

OFF

OFF OFF OFF

OFF

Screen 31: Tracking Boundary Sub-Menu

Page 41

39 / 42

Option

Value

Explanation BOUNDARY LIMIT

ON/OFF

This switches tracking function intervention zone on and off.

CLEAR BOUNDARY

This deletes the intervention area.

LEFT LIMIT

ON/OFF

Left limit of the intervention zone.

RIGHT LIMIT

ON/OFF

Right limit of the intervention zone.

UP LIMIT

ON/OFF

Upper limit of the intervention zone.

DOWN LIMIT

ON/OFF

Lower limit of the intervention zone.

Table 28

Advice for Correct Auto Tracking Use

General warnings

The tracking function should mainly be used in indoor environments. Outdoor use is highly

problematic: the variety of objects (leafs, flags, litter, etc.) moved bythe wind makes use unreliable.

Provide the best lighting possible in the detection zone: in poor lighting conditions, the inevitable

presence of noise on the image makes grayscale variations extremely critical. In poor lighting conditions, the camera may easily loose the tracked object.

If IR illuminators are use, remember that:

The camera must be programmed to operate in B/W only (SETTINGS 1/CAMERA/OTHERS menu) because the Slow Shutter will make tracking unreliable in color mode

The lighting entirely covers the frame where motion is tracked, possibly by restricting the range of action of the camera in tracking mode (using the TRACKING BOUNDARY option).

Avoid background objects in the frame which could trick the motion detector, such as for example

Venetian blinds, gates, doors with grid and objects with very marked, contrasting contours. A chequerboard background is certainly the worst condition for satisfactory operation.

Do not use the privacy zone function in frames where auto tracking is used: the privacy zone can trick the auto tracking function.

Do not use the auto tracking function if the object to be tracked and/or monitored moves too fast.

Recommended control parameters SIZE SENS: select SMALL particularly in poor lighting conditions to improve performance.

GRAYSENS: most false alarms are caused by the tracking of unexpectedobjects. For this reason, it is

preferable to select low sensitivity. ZOOM SETTING: it is advisable to use the lowest possible zoom values. Excessive detail makes tracking

difficult (the movement must be fastener and consequently or the risk of loosing the object is much higher). WAIT TIME: particularly, in the case of poor lighting conditions or frames with interference, it is preferable to

set the lowest possible time to prevent the camera from constantly tracking unexpected objects (e.g. “video noise” in the frame).

TRACKING SPEED: the AUTO setting should always be preferred, unless the object to be tracked does not always move at low, constant speed.

TRACKINGBOUNDARY: it is strongadvised to delimitthetrackingzone, avoiding including unnecessary

parts in the frame.

Page 42

40 / 42

Option

Value

Explanation

EDIT DOME LABEL

This submenu is used to access writing mode for associating a camera label (see below).

CLEAR DOME LABEL

This submenu allows deleting the label associated to the camera (see below).

4.5.5. DOME LABEL MENU

DOME LABEL

BACK

EXIT

Screen 32: Dome Label Menu

Table 29

EDIT DOME LABEL submenu

The operations needed to associate a label to a camera are:

1) Use the joystick to point the cursor to the ”EDIT DOME LABEL” option.

2) Press OPEN. The following menu will appear on the display:

DOME LABEL

0 1 2 3 4 5 6 7 8 9 Y Z y z A B C D E F G H I J K L M N O P Q R S T U V W X

a b c d e f g h I j k l m n o p q r s t u v w x

OK CANCEL

SPACE BACKSPACE

Screen 33: Dome Label

3) Point the cursor to the first character to be used and press OPEN. Point the cursor to “BACKSPACE” to delete it.

4) After writing the text, point the cursor to OK and press OPEN to save and go back to the main screen.

4.6. SPECIAL CONTROL PANEL COMMANDS

The camera can be programmed and operated using various quick control panel commands.

Control panel command

Function PRESET + 95 + ENTER

Accesses main menu

PRESET + XXX + ENTER

Stores preset position (Preset) xxx.

CALL + XXX + ENTER

Recalls preset position (Preset) xxx.

PRESET + 80 + ENTER

Stops the tracking function

CALL + 80 + ENTER

Starts the tracking function

CALL + 81 + ENTER

Stops all functions

PRESET + 82 + ENTER

Stops the cruise function

CALL + 82 + ENTER

Starts the cruise function

PRESET + 83 + ENTER

Delete all Presets

PRESET + 84 + ENTER

Store pattern 1

PRESET + 85 + ENTER

Store pattern 2

PRESET + 86 + ENTER

Store pattern 3

PRESET + 87 + ENTER

Store pattern 4

CALL + 84 + ENTER

Start pattern 1

CALL + 85 + ENTER

Start pattern 2

CALL + 86 + ENTER

Start pattern 3

CALL + 87 + ENTER

Start pattern 4

Page 43

41 / 42

CALL + 88 + ENTER

Start park action function

CALL+89+ENTER

Stop park action function

PRESET + 97 + ENTER

Stop random scan function

CALL + 97 + ENTER

Start random scan function

PRESET+98+ENTER

Stop frame scan function

CALL + 98 + ENTER

Start frame scan function

PRESET + 99 + ENTER

Stop auto scan function

CALL + 99 + ENTER

Start auto scan function

Table 30

When storing Presets, it is important to remember that some are reserved and cannot be either stored or used for positioning the camera.

Presets from 80 to 99 are reserved for management controls Presets from 100 to 103, 170 to 173 are reserved for Tracking and Pattern controls

Page 44

42 / 42

5. TROUBLESHOOTING

Problem

Possible Reason

Solution

Wrong wire connections

Check and reconnect wires Wrong or bad power source

Change power source Fuse broken.

Change fuse

Power on normally but no video signal

Power cable is disconnected

Reconnect power wiring

Address, protocol, and baud rate is not correctly set

Check and set the parameters again.

Pan/Tilt not initializing when power on

RS-485 cable is not correctly connected

Check and reconnect Rs485 cable Video cable is wrong

Check and reconnect video Video is not stable

Power source is wrong

Change the power source Control center is not stable

RS-485 wiring error

Check and reconnect the RS485

Table 31