SDOMEOAT2-SD310
---------------------------------------------------------------------
High Speed Dome
Series
---------------------------------------------------------------------
User
Manual
CONTENTS
I Before Installing ………………………………….………….…………
2
II Key Features ……………………………………………………. ……
2
III Environmental requirement …………………………………………
2
IV Dome setting Instruction ……………………………………………
2
Camera ID Setting………………………………………………………………….
4
Camera Module Setting…………………………………………………………. .
5
V Basic High Speed Dome Operation …………………………………
6
OSD Operation………………………………………………………………. ……
7
Enter OSD …………………………………………………………………………. .
7
Menu function instructions………………………………………………………
7
Camera Exposure………………………………………………………………….
7
White Balance………………………………………………………………………
8
Privacy Mask ………………………………………………………………………
9
Others of the Camera menu……………………………………………………….
9
Camera Mode………………………………………………………. . ………………
9
Zoom Speed ………………………………………………………………………
10
Focus Speed ………………………………………………………………………
10
Pan……………………………………………………………………………………
10
Shortcut Key…………………………………………………………………………
10
Leisure Time ………………………………………………………………………
11
VI High Speed Dome Camera Menu……………………………………
12
VII Auto-Tracking ...............................................................................
15
VII Analysis on Common Malfunctions and Maintenance…
16
2
I Before Installing
Installation should be carried out only by qualified personnel and in accordance with
any wiring regulations in force at the time.
Please read this instruction and warnings before installing.
Do not attempt to service or repair the speed domes as opening or removing covers
may expose dangerous voltages or other hazards. Refer all servicing to qualified
service personnel.
Adequate protection against lightning strikes and power surges must be installed to
prevent damage to the speed dome.
II Key Features
360º Panning, speed is 0.1º-300º/s.
Auto flip 180º
128 presets, the accuracy of preset is less than 0.1º
4 dynamic privacy zones (SONY Camera Module)
Auto cruise by preset, the leisure time is 1s-250s.
Image freeze while panning
Manifold of scan, scan speed could be set from 1º/s to 80º/s
Left limit and right limit scan.
7 alarm input and 2 relay output.
Easy fixing configuration
24V power supply built in
Static proof and thunder proof design
III Environmental requirement:
Operation Temperature: -40-+60
Humidity:<90%
Air pressure: 86-106Kpa
Power supply:AC24V/2.5A, 50/60Hz
IV Dome setting
Bracket Configure
3
Setting Attention:
Adequate protection against high speed dome falling and damage when installing.
The dome should be hang setting, and please avoid up side down.
Please install the dome at the low humidity condition and keep it sealing for avoiding any damage to
dome.
Please set the power switch correct.
Ceiling mount Wall mount
Communication PCB
PCB Locker
Open Up the PCB
DIP table of Communication PCB board
Note: The PCB can be locked by the PCB locker as the picture showed, and it can be turned
over when do the setting works as below (Please turn the locker to the housing side to
open it):
The system setting Switch Camera ID
SW1 SW2
Alarm connector 8P Short connector
AUX 4P
RS485 communication 2P
AC24V power supply
4
Alarm signal
Alarm Relay Output “AUX1”
Alarm Relay Output “AUX2
Alarm Input GND
1、 Power supply and
communication cable：
AC24V
2、Video output：
AC24V RS485
Alarm input signal： l -7
AL1、AL2、AL3、AL4…AL7：Alarm input.
The switch setting SW1 ON=1 OFF=0
Protocol setting
Baud rate setting
Alarm
Alarm mode
DIP Switch
1234567
8
Description
SW1234=0000
(PELCO-D/PELCO-P
Auto identify)
SW5,6=
00=2400
01=4800
10=9600
11=19200
1=Alarm
enable
0=Alarm
disable
1=Always short circuit.
(Alarm while open)
0=Always open circuit.
(Alarm while short)
Note：PELCOD、 PELCOP could be identifying automatically. On and off is the corresponding
switch position.
Camera ID Setting:
SW2 switch: address DIP table
CAM ID
1234567
8
1
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
3
OFF
OFF
OFF
OFF
OFF
OFFONOFF
4
OFF
OFF
OFF
OFF
OFF
OFFONON
5
OFF
OFF
OFF
OFF
OFFONOFF
OFF
6
OFF
OFF
OFF
OFF
OFFONOFF
ON
7
OFF
OFF
OFF
OFF
OFFONON
OFF
8
OFF
OFF
OFF
OFF
OFFONON
ON
5
CAM ID
1234567
8
9
OFF
OFF
OFF
OFFONOFF
OFF
OFF
10
OFF
OFF
OFF
OFFONOFF
OFF
ON
11
OFF
OFF
OFF
OFFONOFFONOFF
12
OFF
OFF
OFF
OFFONOFFONON
13
OFF
OFF
OFF
OFFONON
OFF
OFF
14
OFF
OFF
OFF
OFFONON
OFF
ON
15
OFF
OFF
OFF
OFFONONONOFF
16
OFF
OFF
OFF
OFFONONONON
∶
∶
∶
128
OFFONONONONONON
ON
129
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
130
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
131
ON
OFF
OFF
OFF
OFF
OFFONOFF
132
ON
OFF
OFF
OFF
OFF
OFFONON
∶
∶
∶
252
ONONONONON
OFFONON
253
ONONONONONONOFF
OFF
254
ONONONONONONOFF
ON
255
ONONONONONONON
OFF
Note：The address of the some protocol are from 0, and the others are from 1, please setting
the address(±1) as your protocol.
Alarm
7 alarm input. The dome will alarm when alarm input port connect the GND. The AUX will be closed
when has alarm, and open when no alarm in. The capacitance of the relay is AC24V/1A.
The relay output:
2 relay switch AUX1, AUX2, the biggest capability is AC24V/1A. AUX1 connect with the alarm, the
master or keyboard controlsAUX2.
Camera Module Setting Switch
The dome can be fit different camera, and they have different switch
6
Camera
Switch 1
Switch 2
Switch 3
Switch 4
DIP-1
DIP-2
DIP-3
DIP-4
SONY
OFF
OFF
OFF
OFF
HITACHI
OFF
OFFONOFF
LG
OFFONOFF
OFF
CNB-200L
OFFONON
OFF
CNB-M1560
OFFONON
ON
SAMSUNG(SDM300/SDM330
)
ON
OFF
OFF
OFF
Note: Please make sure the camera parameters are correct or the camera
cannot work or cannot work well. If this, please enter the camera menu
and restore factory settings first, then setting the parameters as
request.
V Basic high speed dome operation
When power on, the version, protocol, baud rate and ID will display on the monitor,and the domewill
automatic self-check both the vertical and level then display the specs of camera.
Example:
High Speed Dome
Ver：100
PELCO D P
2400
ID：001
Tile reference OK
Pan reference OK
SONY FCB-EX480CP
The operation by keyboard controller
Function
Control
Level / Vertical
Joystick left, right / up and down
OSD Confirm
OPEN
Cancel and Back
CLOSE
OSD Display
Call 95 preset
Original Position
Call 34 preset
Level Scan
Call 99 preset
Auto Flip
Call 33 preset
Left limit: call 92 preset
Level Scan Limit
Point
Right limit: call 93 preset
Call preset scan 1
Call 81 preset
Call preset scan 2
Call 82 preset
Call preset scan 3
Call 83 preset
Call preset scan 4
Call 84 preset
7
Function
Control
Camera mode 1
Call 100 preset
Camera mode 2
Call 101 preset
Camera mode 3
Call 102 preset
4 Privacy mask, only fit to SONY480, SONY980 and SONY1000camera.
Level area increase: FAR
Level area reduce: NEAR
Vertical area increase:TELE
Privacy Mask
Vertical area reduce:WIDE
OSD Operation
Enter OSD
Please call the number 95 preset to display the OSD on the screen.
At figures the current item, figures the enabled item, and the► after the item which have
submenu.You can change the item state when it has been enabled. Please press OPEN key to enter
or confirm and CLOSE key to back or cancel, and the key UP and DOWN control the cursor up and
down.
Menu function instructions
Call the number 95 preset to enter the OSD, and you could set the shortcut key to display the OSD.
Main Menu
Camera ►
Pan ►
Shortcut Key
Self act Nothing
Leisure Time 030
Camera OSD (SONY)
Camera ► Press Key Open to enter the camera menu.
Exposure ►
White Balance ►
Privacy ►
Other ►
Camera Model ►
Zoom Speed 005
Focus Speed 001
Exp Mode Auto
Shutter speed 006
Iris 016
Gain 001
Bright 016
Back Light Off
Slow Shutter Off
Camera Exposure
Exposure ►Press OPEN key to enter the camera exposure
submenu.
Exposure operation
1, How to change the exposure
Exp Mode press OPEN key, enable Exp Mode, then
operate up and down by the joystick, the parameters
are:Auto, Manual, Shutter, Iris and bright
8
2, Confirm Exposure.
Exp Mode pressOPEN key, select effect, the menu change to Exp Mode
3, Cancel Exposure
Exp Mode press CLOSE to cancel the Exposure mode change, the menu change to Exp
Mode
Back the main camera menu
Exp Mode pressCLOSE key to cancel the last menu.
Other operation of Exposure Menu
Exp Mode, control the joystick up or down to let the up and down, press OPEN key to
enable the item, then go on control up and down with joystick, and press OPEN key to confirm, the
cursor will change to .
White Balance
The dome has the function of Manual White Balance andAuto White Balance.
White Balance► press OPEN key, enter the White
Exposure ►
White Balance ►
Privacy ►
Other ►
Camera Model ►
Zoom Speed 005
Focus Speed 001
Balance submenu,then change the parameter,
WB Mode Auto
R Gain 214(0-255)
B Gain 175(0-255)
White Balance Mode operation:
WB Mode Auto
R Gain 210
B Gain 175
WB Mode Auto
R Gain 210
B Gain 175
WB Mode Auto
R Gain 210
B Gain 175
1、 WB Mode
2、 At WB Mode, press OPEN key to enable the Exp Mode
menu, then it will change to WB Mode, control the
joystick to change the parameter which order is: Auto,
Manual,ATW, OPW, Outdoor and Indoor. R Gain
3, R Gain
At WB Mode, operate the joystick down let the
cursor come to R Gain, press OPER key to enter the menu.
Then operate the joystick up (increase) and down (reduce) the
R Gain. The homologous parameter is 0-255. Press OPEN
key to confirm and back or press CLOSE to cancel and back.
4, B Gain
At WB Mode operate the joystick to control the
cursor come to B Gain, press OPEN key to enter the B Gain
setting, joystick up and down to increase and reduce the
parameter which from 0-255. Press OPEN key to confirm and
back or press CLOSE to cancel and back.
9
Privacy Mask
Exposure ►
White Balance ►
Privacy ►
Other ►
Camera Model ►
Zoom Speed 005
Focus Speed 001
Privacy1
Privacy2
Privacy3
Privacy4
At Exposure ► operate the joystick to let the cursor
come to Privacy press OPEN to enter the submenu, then
set the parameter.
There are 4 privacymasks, which have the same operation
1. How to set privacy mask?
At the submenu of the Privacy, press OPEN key to enter the
adjust image, adjust the privacy zone by OPEN (confirm),
CLOSE(cancel), FAR (level increase), NEAR (level reduce),
TELE(vertical increase), WIDE (vertical reduce). Then press
OPEN key to confirm and back.
2 . How to clear privacy mask?
a, Restart the speed dome,all of the privacy mask will be cleared.
b, Enter the menu of the Privacy mask, press OPEN key to enter and press CLOSE to clear the
privacy mask you want to clear.
Others of the Camera menu
Digital Zoom On
Auto ICR Off
ICR Off
Display Off
Exposure ►
White Balance ►
Privacy ►
Other ►
Camera Model ►
Zoom Speed 005
Focus Speed 001
Camera Mode Save：
Normal
Day
Night
Camera Mode Exec：
Normal
Day
Night
Press OPEN key to enable the submenu, operate joystick to
change the states of ON and OFF. Press OPEN to confirm
and back and CLOSE to cancel and back.
Camera Mode
Camera Mode setting menu:
Press OPEN to enter the menu.
There are three save mode under the Camera Mode Save
menu, move the cursor to the mode going to be change,
press OPEN the cursor will change to , the setting will be
saved and it will back to after 1 second.
The three items under Camera Mode Exec is opposite the
three modes above. Move the cursor to the mode you want
to call and press OPEN to confirm and back. The saved mode
could be called bythe shortcut preset: Normal---call100 preset; Day --- call 101 preset; Night --- call
10
AS Speed
060(000-080)
Auto Pan speed
PS1 Speed
120(100-120)
Presets cruise 1 speed
PS1 Time
005(5-120) )
Presets cruise 1 stop time.
PS2 Speed
120
Presets cruise 2 speed
PS2Time
005
Presets cruise 2 stop time.
PS3 Speed
120
Presets cruise 3 speed
PS3 Time
005
Presets cruise 3 stop time.
PS4 Speed
120
Presets cruise 4 speed
PS4 Time
005
Presets cruise 4 stop time.
Auto Flip
On(On/Off)
102 preset
Zoom Speed
At the submenu of Exposal, move the cursor to Zoom Speed, press OPEN, the cursor will change
to , then the parameter can be changed. Press OPEN to confirm and back or CLOSE cancel and
back.
Focus Speed
Move the cursor to Focus Speed, press OPEN, the cursor will change to , then the parameter can
be changed. Press OPENto confirm and back or CLOSE cancel and back.
Pan
Home place Off
This operation can control the home place of the dome,
AS speed 060
PS1 Speed 120
PS1 time 005
PS2 Speed 120
PS2 time 005
PS3 Speed 120
PS3 time 005
PS4 Speed 120
PS4 time 005
Auto Flip On
adjust the auto panning speed and 4 cruise line with presets,
also the auto flip function.
Home Place OFF (001-032, OFF)
Shortcut Key
The functions can be setting by presets number, and can be called by the preset number which be
set.
Note: The right side number is the default short cut key, they are the number of presets. The
number can be saved by new shortcut but the old one will not be cancel.
Example:Change the number 095 into 16 thatafter Open Menu, the Menu can be called by 16 preset,
and also can be called by 95 preset.
Open Menu
095
Auto Flip
033
Reference
034
Left Limit
092
Right Limit
093
Preset scan 1
081
Preset scan 2
082
Preset scan 3
083
Preset scan 4
084
Auto Scan
099
Camera ►
Pan ►
Shortcut Key
Self act Nothing
Leisure Time 030
In the presets, the preset scan line 1 will cruise from presets
1-8, and preset scan line 2 will cruise from presets 9-16, the
preset scan line 3 will cruise from presets 17-24, and the
preset scan line 4 will cruise from 25-32. Every line will back
the first preset when it met the point never be set, and it will
quit cruise if the first preset is not be set. The function Auto
Scan is right and left limit scan.
Note: The changing of the shortcut key can not be identical
with the shortcut key already have.
Operation: Move the cursor to the item which going to be
changed, press OPEN, then change the parameter, press
OPEN to confirm and back or CLOSE cancel and back.
Self Act.
The dome will check itself when electric and it will act the
program automatic.
11
Nothing
P Scan 1 Preset scan 1
P Scan 2 Preset scan 2
P Scan 3 Preset scan 3
P Scan 4 Preset scan 4
A Scan Auto scan (left and right limit scan
Home Home place
Operation: Press OPEN the cursor will change to , and the parameter can be change. Press OPEN
to confirm and back or CLOSE to cancel and back.
Leisure Time
Camera ►
Pan ►
Shortcut Key
Self act Nothing
Leisure Time 030
The dome will back to the home place after a while if it is
moved manually, and the time is Leisure Time
The parameter is from 1-240.
Operation: Press OPEN the cursor will change to , and the
parameter can be change. Press OPEN to confirm and back
or CLOSE to cancel and back.
12
VI High speed dome camera menu
Control
OPEN
Confirm (SET)
JOYSTICK
Cursor Up/ Down
NEAR
Control the cursor Up/Right
to change the parameter
FAR
Control the cursor Down/ Left
to change the parameter
►
Currently menu（You can change the parameter only when at the currently
menu）
Which have submenu,and press OPEN key to enter
13
Enter the Camera menu:
MAIN SETUP
►CAM TITLE ON
WHITE BAL ATW
BACKLIGHT OFF
MOTION DET OFF
FOCUS
EXPOSURE
SPECIAL
RESET
EXIT
CAM TITLE
ABCDEFGHIJKLMNO
PQRSTUVWXYZabcd
ef g h ijkl m nop q r s
tuvwxyz01234567
89 ( )<>-/#!?, .
← → CLR POS END
_ _ _ _ _ _ _ _ _ _
ATW SETUP
►MODE SEL OUTDOOR
Press SET to Return
WDR SETUP
►WDR LIMIT MIDDLE
Press SET to Return
MOTION DETECTION
►SENSITIVITY
50
Press SET to Return.
1. CAM TITLE
2, WHITE BAL
Please chose AWC-SET mold when at these situations
below:
The scenes have high COLOR TEMP things, for
example the sky or setting sun.
Caliginousscenes.
The camera in the direction of the fluorescent lamp.
3, BACKLIGHT
Attention:
If the SHUTTER setting is MANUAL, the WDR function
can not use.
Please pay attention to the brightness of the monitor
when setting the parameter.
AddWDR may induce abnormity.
Please do not use WDR when in these condition:
abnormally color appears; ripple showed at the bright
part.
4, MOTION DET
Attention:
Please make sure if the camera could work normally
after every adjust
This function wills not working if the bright light
coruscates.
The other function will carry out more time if this
function opens
14
5. EXPOSURE
EXPOSURE SETUP
.
►BRIGHTNESS
50
IRIS AUTO
SHUTTER --AGC
MIDD
L SSNR
MIDD
L
SENS-UP
AUT
O END
SET SHUTTER
►SHUTTER 1/60
Press SET to Return
SHUTTER:
Attention:
When setting the BACKLIGHTas OFF, the A.FLK will show the best effect.
If camera setting as ESC, the image will not steadily when face to the high light.
Can not use WDR when setting as MANUAL.
SEND-UP will can not use if under the MANUALand A.FLK mode.
6. SPECIAL
SPECIAL SETUP
►USER PRESET OFF
PRIVACY OFF
DAY/NIGHT
COLO
R SYNC INT
FREEZE OFF
H-REV
OF
F V-REV
OF
F IMAGE ADJ
COMMUNICATION
EXIT
COMMUNICATION
Attention:
The COMMUNICATION parameter are setting previous, please do not change the parameters
if not sure, or it will induce the camera abnormally.
15
VII Auto-Tracking
Parameters Setting
Protocol ：PELCO-D / PELCO-P Baud
Rate：2400 / 4800 / 9600
How to use auto-tracking function?
This function is closed as default setting, and the setting table as below:
Preset Number
Function
Default
Setting
35
Start-up Auto Tracking
36
StopAuto Tracking
YES
230
when the state of untrackable objects happen
the PTZ will move to Preset 1
YES
231
when the state of untrackable objects happen
the PTZ will not track anymore
232
when the state of untrackable objects happen
the PTZ will keep motion detection on other
moving object
233
The sensitivity of tracking：Low
234
The sensitivity of tracking：Medium
YES
235
The sensitivity of tracking：High
236
Object Size: Small
237
Object Size: Medium
YES
238
Object Size: Large
239
Object lost time：5 Second
240
Object lost time：10 Second
241
Object lost time：15 Second
YES
242
Object lost time：20 Second
243
Object lost time：25 Second
244
Object lost time：30 Second
245
Object lost time：35 Second
246
Object lost time：40 Second
247
Auto Zoom：Open
248
Auto Zoom： Close
YES
Note: When you open the function of AUTO ZOOM, the lens will keep zoom in as the object
move and not good at zoom out. When the object is too close to track, please just let the PTZ back
to Preset 1 at the best position of it.
16
VIII Analysis on Common Malfunctions and Maintenance
If there is any problem at your operation, please work through the logical
steps below to determine and rectify the problem.
Symptom
How to solve the problems?
No self-test
1 .Check the power supply and make sure if fuse is blow out or not
2. Make sure the adaptor of speed dome is specifically designed for use
with this speed dome and verify that the input of speed dome inside is
approximatelyAC24V.
3. Make sure the power pin on communication board is fixed but not loose.
No Picture
1. Check the PCB to make sure the red power LED is lit. If the power LED
is lit, check the BNC crip connection is correctly made at both the PCB
end and the monitor /DVR /matrix end.
2. Check that the PSU is correctly connected and make sure the camera
module match this speed dome.
Self-test abnormal
1. Check the connection between camera module and PTZ.
2. Make sure that the DIP of speed dome setting is correct.
Suggestion: check the camera module and confirm the DIP setting and
then restart speed dome.
No PTZ control
1. Check the power on self test screen to ensure that the protocol, ID and
baud rate are as expected.
2. If the settings match, you should check the polarity of the
communication RS485 connections, both on the control equipment and
the speed dome.
3. Check that the control equipment setting is available and if it is
compatible with the speed dome and is configured to match the speed
dome setting correctly.
4. Check the address switch setting is answer for host which you
controlling (some of host address is 1 but camera address is 0 and vice
versa.
Make sure if the wire on communication board is fixed.
Work normally for
close distance
controlling but not
available for long
distance
1. The output drive of RS485 converter beyond their ability.
2. If the transport distance is over 1200M, then you need add a RS485
repeaters or signal amplifier.
3. Make sure that the short circuit pin of 120Ohm resistance connect
correctly.
Loading...