XtendLan TC-800, TC-850, TC-850CF, TC-850CE, RB-851 User Manual

Fanless Mini PC

TC-800 800MHz Mini PC
TC-850 800MHz Mini PC, with LPT/COM
TC-850CF 800MHz Mini PC, with LPT/COM/CF
TC-850CE 800MHz Mini PC, with LPT/COM/WinCE
RB-851 800MHz Mini PC, with LPT/HDD/CF/miniPCI
RB-852 800MHz Mini PC, with LPT/CF/2x LAN/miniPCI
RB-853 800MHz Mini PC, with LPT/HDD/CF/2x LAN
RB-854 800MHz Mini PC, with LPT/HDD/CF/6x USB

User’s Manual

SAFETY INFORMATION

WARNING

Do not expose your computer to rain or moisture, in order to prevent shock and fire
hazard.

Never install your computer in wet locations.
Do not open the cabinet to avoid electrical shock. Refer to your nearest dealer for

qualified personnel servicing.
Never touch un-insulated terminals or wire unless your power adaptor and display

monitor are disconnected.
Locate your computer as close as possible to the socket outline for easy access and to

avoid force caused by entangling of your arms with surrounding cables from the
computer.

When using Mini PC, avoid using or installing the modem to the serial port during a
storm or a lightning.

Do not use the modem or a telephone to report a gas leak in the vicinity of the leak.
USB connectors are not supplied with Limited Power Sources.

REGULATORY

FCC CLASS A NOTE

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio freq uency energy and, if not installed and used in
accordance with the instruction manual, may c ause harmful interferenc e in which case the us er will be
required to correct the interference at his own expense. Testing was done with shielded cables.
Therefore, in order to comply with the FCC regulations, you must use shielded cables with your
installation.

WARNING

This product Complies with EN55022 Class A. In a do mes tic env ironment this product may cause radio
interference in which case the user may be required to take adequate measures.

Changes or modifications to this unit not expressly approved by the par ty responsible for compliance
could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operati on is subjec t to th e foll owing two condi tions :
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital
apparatus as set out in the interference - causing equipment standard entitled “Digital Apparatus”,
ICES-003 of the Department of Communications.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils
numériques de Classe (A) prescrites dans la norme sur le matériel brouilleur: “Appareils
Numériques”,NMB-003 édietée par le miniistre des Communications.

MANUFACTURER’S DECLARATION OF CONFORMITY

This equipment has been tested and found to comply with the require ments of European Community
Council Directives 89/336/EEC and 73/23/EEC relating to electromagnetic compatibility and product
safety respectively.

ATTENTION

This product has been designed and certified to comply with certain regulatory requirements pertaining
to Information Technology Equipment. This product has not been designed for use as a medical
device. Without limitation of the foregoing , this product is not intended and has not be en certified for
use in a hospital or clinical environment to diagnose, treat, or monitor patients under medical
supervision, and is not intended and has n ot been certified to make physical or electrical contact with
patients, nor to transfer energy to or from patients and/or to detect such energy transfer to or from
patients.

PREFACE

TC-800/TC-850/TC-850CF/RB- 850/RB-851/RB-852/RB-853/RB-854

XTENDLAN introduces an industrial classic in the computing industry, by featuring TC-800,TC-85x, RB-85x,
a compact PCs that connects people through networking via global internet across the continents over the
channels of sea bay. The conquest for browsing e-information through wired LAN/WAN. This portable device
is handy for travelers and service technicians who worked in and out of the office. For office desk workers,
this showpiece occupies very little space on a corner of the table, and it is so convenient that you may locked
it in your drawer after office hours.

A jewel in the crown MiniPC for thin client users, which is handy-rugged-robust. TC-800,TC-85x, RB-85x
serves as the Internet Appliance that offers state-of-art design for applications surrounding networking,
computing, transaction and information transport.

XTENDLAN connotes the MiniPC for small business enterprises to serve these boxes to users for the
connection to a server as thin client. The MiniPC achieves multi-servers requirement to serve as firewall,
mail-server, print server, and many other single task application in the office. Furthermore, with MiniPC,
business executive can work his way from the office to home, a student can do his assignment from the
dormitory and continue back at home. TC-800 allows you to use your computer with just one finger press at
the power button. It is built in an awesome mechanical dimension of 170×124×38mm(or 58mm TC-85x, RB­85x), equivalent to 4.32”x3.15”x0.96”(or 1.47”), this is just a right device for space conscious environment.

A

t

(

)

) (

)

(

)

t

g

y

@

A

A

t

(

)

@

p

top

)

)

g

(

)

g

SPECIFICATION

Features

CPU Onboard VIA EDEN-N Nano BGA processor

800MHz

BIOS
System Chipse
I/O Chip VT1211
System Memory Onboard 256MB DDR266
Expansion 1x X-PCI connector

I/O

MIO 1x EIDE (Ultra DMA 133

USB 2x USB 2.0 Ports (one in front

Display

Chipse
Display Memory 8/16/32 MB share system memor

Resolution CRT

Audio

Ethernet

Chipse
Remote Boot ROM Built-in boot ROM function

Mechanical &Environment

Power Requirement+
Operating Temperature 0 ~ 60oC (32

Operating Humidity 0 ~ 90% relative humidity, non-condensin
Size (W x H x D)

Weight (3800/3850) 920

Inte

C97 2.2 (Codec) VT1612
udio Interface Line out, Line in, Mic in

VT6103 10/100 Base-T

MI BIOS

VIA CLE266 / VT8235

(optional), 1x CF (optional)
1 x RS-232 (optional) , 1x PS/2 K/B, 1 x PS/2 Mouse
More info in Apendix

rated VIA UniChrome 2D/3D Graphics with

MPEG2 Accelerator
CRT mode : 1280 x 1024

LCD/Simultaneous mode : 1280 x 1024 @ 32 bpp
(85Hz)

5V~5.25V
DDR266 & La

170 x 124 x 58 mm

4A (with VIA Eden-N 800Mhz, 256MB

–

Description

RB-851, RB-852

optional), 1 x LPT

6x USB RB-854

32 bpp (85Hz)

2x LAN optional

HDD

140oF

TC-800 170 x 124 x 38 mm

TC-800,TC-85x, RB-85x OVERVIEW

Front Panel

Power LED

The power LED lights up, when system is turn on.

HDD LED
The HDD LED flashes when the system is working. Please do
not turn off the system when HDD start running

Power Switch

Depress switch to turn on & turn off the systems.

USB port
For connection to devices with USB interface (keyboard,
mouse, HDD, CDROM, Memory Stick, etc.)

Back Panel

Power switch

DC Power Jack (3-pin)

PS/2 Keyboard & Mouse (6-pin)

PS/2 Mouse (6-pin)
USB port
RJ-45 LAN Jack
VGA port
Mic-in
Audio Line out

PERIPHERALS

ONNECTING THE POWER ADAPTOR

C

Power Adaptor

To use your computer immediately, take and use the supplied AC
adapter as a power source. See the left diagram for visual connection.

Connect the DC power jack of the power adaptor to the DC Input jack
of TC-800/850.

Turning ON Your Computer

Press the power button as indicated on the figure on your left­side, the system will start automatically.

CONNECTING THE MONITOR

VGA Connection
Depending on your choice of viewing, select a conventional CRT or the

LCD VGA monitor.
Make your connection by following the reference diagram from the

VGA cable of your cable to the 15-pin D-Sub VGA port.

PERIPHERALS

ONNECTING THE USB

C

TC-800/850 provides USB port (one each in front & at the back of the cabinet).

Front cabinet Turning ON Your Computer

Press the power button as indicated on the figure on your left-side, the
system will start automatically.

CONNECTING USB, SPEAKER/EARPHONE AND WEB

USB Port

The second USB port is available for connection to USB devices.
Connecting to WEB
There is an available RJ-45 LAN jack for connection to the hub of

your intranet; and via your server for internet service (see
diagram for RJ-45 LAN jack).

Speaker/Earphone

TC-800/850 supports Input/Output device for speaker, earphone
and MIC (Microphone), etc…

CONNECTING THE KEYBOARD AND MOUSE

Describing Mouse actions

Action Description

Point -Slide and point your mouse to your desired position.
Click -Press the left button once.

Double-click -Press the left button twice.
Right-click -Press the right button once. When selecting (most) programs, this action

displays a shortcut menu of the context-sensitive choices.

Scroll wheel -Move your finger along the wheel of your mouse (just upright your middle

finger) and scroll vertically to move page upward and downward.

Describing Keyboard

The keypad usually comes in standard QWERTY; except that different language(s)
keyboard comes with additional special characters..

CONNECTING PRINTER PORT

Printer Port
The printer port is usually connected to a Printer for printing

hardcopy materials. It is normally idle most of the time.

BIOS

RECONFIGURING TC-800,TC-85x, RB-85x

1 Take note that AMI BIOS is used in the TC-800/850. To reconfigure the computer, depress or hit

the <Del> key to enter your BIOS setup main menu.
2 Select from the menu, the desired setup for change.
3 Press <Esc> to go back to main menu.
4 Move your cursor to “Save Settings and Exit”, press “Y” to save the changes that you just made.

TC-800/850 will restart accordingly to your new setup.

ONBOARD CONNECTORS SUMMARY

SUMMARY TABLE FOR CPU BOARD

Nbr Description Type of Connections Pin

J1: LAN RJ-45 FOXCONN 8-pin
J2: IDE Connector Box Header, 22x2-2.0mm 44-pin
J3: VGA Connector D-Sub Connector 15-pin
J4: USB1 (Front) USB 90o Type1 Connector 8-pin
J5: USB (Back) USB Type1 Connector 6-pin

J6, J7: PS/2 Keyboard &

Mouse

J8 PRN (Printer) Box Header, 13x2-2.0mm 26-pin

J9: COM1 /RS-232 Pin Header, 5x2-2.0mm 10-pin
J11, J13: Line-Out, MIC Two contact Switch 6-pin
J12, J19: Line-In, SB5V Wafer Header 4-2.0mm 4-pin

J15: RST (Reset) Header 2x1-2.0mm 2-pin
J16: Fan Wafer Header 2-2.0mm 2-pin
J17: DC 5V Input
J18: X-PCI Header 32x2-2.0mm 64-pin

SP1: Buzzer

Mini-Din Connector 6P

Mini-Din Connector 3P

APPENDIX

nbrs.

6-pin

3-pin

2-pin

R

EAR CONNECTORS OUTLINE FOR TC-800

Line Out VGA RJ-45 LAN Jack PS/2 Mouse DC Power Jack

MIC-IN USB PS/2 Keyboard Power Switch

EAR CONNECTORS OUTLINE FOR TC-850/850CF/850CE

R

Power Switch PS/2 Keyboard USB VGA Line-Out Jack Out

PS/2 Mouse RJ-45 LAN Jack MIC-IN

DC Power Jack Printer Port Serial Port

REAR CONNECTORS OUTLINE FOR RB-85x series

RB-851

Compact flash slot

RB-852 / RB-853

2nd RJ-45 LAN

RB-854

PIN ASSIGNMENTS

1

2

3

4

5

6

1

2 NC

3

4

6

6

7

8

J6:KBD(PS/2Keyboard & Mouse) – 6-pin Mini-Din Connector

Pin # Signal Name

KBCLK
PMCLK

GND
KBDAT
PMDAT

SB5V

J7: Mouse (PS/2 Mouse) – 6-pin Mini-Din Connector

Pin # Signal Name

PMCLK

GND
PMDAT

5

NC

SB5V

J1: RJ-45 FOXCONN (LAN)– 12-pin RJ45 Connector

Pin

SignalName Pin

#

1

FTXD+ 2
3 FRXIN+ 4
5

NC
NC

SignalName

#

FTXD-

NC

FRXIN-

NC

J8 : Printer- 25-pin Dsub Connector

Pin #

1 STB- 14 AFD­2 PD0 15 ERR­3 PD1 16 PRINIT-
4 PD2 17 SLIN-
5 PD3 18 GND
6 PD4 19 GND
7 PD5 20 GND
8 PD6 21 GND

9 PD7 22 GND
10 ACK- 23 GND
11 BUSY 24 GND
12 PE 25 GND
13 SLCT - -

Signal
Name

Pin # Signal

Name

1

2

3

4

5

2

3

4

5

Power Sw – Push Button Switch

Pin # Status

| ON

O OFF

J17: DC-IN (DC-IN 5V) – 3-pin MINI-DIN Lock Pin Socket

Pin # Signal Name

1 VCC
2 GND
3 NC

J4: USB1 (USB1x90

o

)– 4-pin USB Type 1 Connector (Vertical Type)

Pin # Signal Name

VCC

USB0-

USB0+

6 GGND

GND

GGND

J3: VGA – 15-pin Dsub Connector

Pin

SignalName Pin

#

1

MR
MG
MB
NC

GND

SignalName Pin

#

6 GND
7 GND
8 GND
9 NC

10 GND

SignalName

#

11
12
13 HYSYNC
14 VSYNC
15

NC

VCC

VCC

J5:USB (USB2): For connection to external –4-pin USB Type

1

2

3

4

1

2

A

4

5

1

2

4

3

5

7

9

1 Connector

SignalName

Pin #

VCC

5
6

USB2-

USB2+

GND
GGND
GGND

USB J11: MIC_IN – 5-pin RCA Phone Jack device

3

SignalName

GND

UD MIC

GND

GND

REF

Pin #

J13: Line-out – 5-pin Phone Jack

J9: COM1 - 9-pin Dsub Connector

Pin

#

1

Pin #

3
5

SignalName

DCD1 2
TXD1 4

GND 6

RTS1 8

RI1

SignalName

GND

LOUT L

NC
NC

LOUT R

SignalName

Pin

#

RXD1
DTR1
DSR1
CTS1

Action status

LEDS: POWER ON/OFF & HDD R/W

LED
Color

Green
Red

Flashes

State

Power
On
HDD
R/W