XtendLan IPM-401W User Manual

IPM-401W

User Manual

- 2 -

Table of Content

Product Overview ............................................... 3

Features .............................................................................................. 3

Specification ....................................................................................... 3

Interface Description ......................................... 5

Front View ......................................................................................... 5

Rear View ........................................................................................... 7

Setting up your device ....................................... 9

Before we Start .................................................................................. 9

Hardware Connection ....................................................................... 9

Software Installation ......................................................................... 9

Web Interface .................................................... 19

Connect to your Device .................................................................. 19

WiFi Information ............................................................................ 46

Load Factory Default & Restart System ...................................... 63

Controlling the Device ..................................... 66

FAQ : ................................................................. 70

- 3 -

Product Overview

Features

1.

Built in Web Server Design, directly control by web browser – PC & Smartphone :
Internet Explorer (IE) , Firefox , Google Chrome,
Safari ( iPhone ) and Android browser of smartphone

2.

Support WiFi - Wireless 802.11 N/ B/ G and WPS connection

( WPA-PSK, WPA2-PSK, AES,128-bit WEP,64-bit WEP,TKIP, WPA2,WPA )

3.

Support HTTPS , TCP/ IP , DHCP, DDNS, SNMP & SMTP

4.

Control 4 individual outlet power ON & OFF .

5.

Detect the consumed current of 4 individual outlet & show in LIVE line chart

6.

Over Current protection and record Current Value history

7.

Temperature detection - for Internal use only

8.

Support USB Webcam( W/ UPNP, M-JPEG / YUV ) to view the area near IPM-401W.

9.

With IR remote controller : control directly without need through PC web browser

10.

Time scheduler : Multiple time setting for each outlet power ON , OFF or REBOOT

11.

Auto Ping (Watchdog) capability to control external devices automatically

12.

E-mail functionality for

13.

notifying user - Support public e-mail --Google mail & Hotmail . .

14.

Supply “ Log “ function to store device information and usage record

15.

Fuse protection as power overloading ( total 10Amp)

16.

Support Telnet , SNMP , and HTTP CGI command ( SDK) for system integration

17.

CNT Technology – for quick and easy setup without port forwarding on Router , just plug
and play

18.

IP Server: for quick search and easy access in Internet by name without thru DDNS.
Easily find on internet without remember the complicated IP address number

19.

Option : RS232 control ( request by OEM /ODM only )

Specification



Power input : 100V - 240V



Maximum loading of each output: 9 amp



Maximum of Total loading : 10 amp ( 220V) / 15amp ( 110V)



Fuse protection : 10 amp ( with spare fuse in socket )



Dimensions: 195 x 135 x 48 mm ( L x W x H )



Weight: 1kg

- 4 -

Minimum System Requirements

Package Contents

1. IPM-401W Unit x 1

2. IR Remote Power Control

3. IPM-401W Installation CD

3. WiFi Antenna
X 2 pcs

5. RJ45 Cable x 1 (option)

5.) Input Power Cable (option)

Please double check the power cable compatible
for 10 amp current loading .

WINDOS PC OS with network capacity.
Browser : IE 9.0 or above , Firefox, Google Chrome , Safari
RJ45 LAN & Internet HUB & Switch
JAVA version 1.60 or above to check USB Webcam under web browser Internet Explorer -IE
Internet ( for remote access) or Ethernet Network ( Internal Network use) with some type of
Internet connection, (i.e. ADSL, Cable, Dial up or any other forms of Internet service)

Package Contents

- 5 -

Interface Description

Power Status Indicator:

The Power Status Indicator - Green light ON
as power ON.

Reset :

There are 2 function for this button.
*

Enable WPS function by one short click

There is one long beep as enable WPS
function. Please refer page #16 for details.

*

Set back to default setting by long press

To reset to original manufacture settings, hold
down the reset button with a sharpen pin for

5- 6 seconds then release. There are THREE

beeps response ( short –- mid long – short )

which means reset successfully and

IPM-401W will be rebooted itself ( one beep

after reboot ) and most information go back to

default setting ( LAN IP )

Restart :

The restart button just resets the device by

turning off and then turning on the power.

Front View

- 6 -

Link:

The Link Indicator shows the WiFi signal
transfer status. The light will be ON all the time
and flashing while transfer data.

IR Receiver :

This area is for receiving the signal from
handheld IR remote controller which comes in
shipping package.

Network:

10/100 Mbps network

USB:

USB 2.0 for USB Web Camera. (With UPNP &
video format as M-JPG / YUV )

RS232 Serial Port Console :

Under construction

- 7 -

Rear View

Rear View

4 Output Power Ports:

Connect up to 4 separate devices
that will be controlled by the IPM­401W. Ports 1 - 4

1 Input Power Port :

In this socket, there is power input
and Fuse socket .



The input power sends power
to the IPM-401W.



Fuse : To prevent electrical
surges from damaging the unit.
The IPM-401W comes with
one spare fuse in the unit.

TYPE：U/C GFE 10A 250V (PF)

1 Power Switch:

The Power switch turns on the

input power.

- 8 -

Fuse replacement

1.) The fuse is located between the power switch and the power input plugs.

2.) Carefully remove the fuse holder with a flat screwdriver.

3.) The fuse can be purchased from electronic shops.
Specification : U/C GFE 10A 250V (PF)

- 9 -

Setting up your device

Before we Start

*Before setting up the device make sure of the following:

1.) All the package contents are all included if anything is missing please contact the dealer
where the device was purchased from.

2.) Check the power input cable is working correctly.

3.) Check all cables to make sure there are no problems with it.

Hardware Connection

Please refer following procedure :

1.) Connect the Ethernet cable (RJ45) to the IPM-401W to your local area

network. 2.) Then connect the power cable into the power input port of the IPM­401W.

3.) Connect the device that you would like to control to the output plug on the top of the IPM-

401W. 4.) Switching the power source to ON status , this switch is located at the rear of 9258.

5.) After power on for around 45 seconds , there is a short beep sound for IPM-401W which

means the system reboot successfully

5.

) Go to page #14 for software installation guide – use IP EDIT to log in the webpage of

IPM-401W.

Note: To change the network setting for WiFi connection ( if your Router without WPS function ) ,
please go to page # 12 to setup the WiFi connection manually .

Software Installation

The Media Link - IP Family CD comes with the device , it will have all the necessary software to
run and setup the device.

IP Power Software:

IP Edit (Required)
IP Power Center *( For multiple IP Power devices control )

Installing Software

1.) Place the Media Link-IP Family CD into the CD/DVD Rom drive.
(The CD should auto run but if it does not go to the CD/DVD Rom drive and select the
“autorun.html” file.)

- 10 -

2.) Click on the IP Power Section Bar

3.) Select the IP Power IPM-401W

- 11 -

4.) All the available downloads for the IPM-401W will be shown

5.) Download the required software – IPEdit.exe - by clicking on the download button.

Then you can select to connect IPM-401W by LAN or by WAN ( WPS)

- 12 -

Connection by WiFi- WPS ( WiFi Protection Service )

IP Power IPM-401W support WPS function which can assist user setup the WiFi connection of
user`s router and IP Power IPM-401W automatically . Before using WPS function, please check
your WiFi router and see if there has WPS function first . There should have a button name
“WPS / QCC “ or a sign on the router for user to click easily.

Please refer following steps to setup WiFi –WPS connection
Step 1: Power on the IPM-401W - only connect power in but do not connect the LAN cable , you

will hear one short beep in 40 seconds means IPM-401W boot successfully
Step 2: Press the “WPS button” of your WiFi Router. ( Please check your router WPS function )

Step 3 : Press One time ( short) the “ Reset button” of IPM-401W and then there is one long
beep which means the WPS function of IPM-401W enable .

Step 4: After few seconds , there are 2 beep : short Beep + middle beep

Which means WPS connection successfully
( If WPS connection fail , there is one long beep mean the connection fail.
Please go back to step 2 and try again )

Step 5: Power to reboot IPM-401W . There is one short beep in 45 seconds which means
IPM-401W boot up successfully .

- 13 -

Step 6 : Execute IPEDIT.exe . There is WiFi IP address of IPM-401W shown in IPEDIT.exe
as following :

Step 7 : Double click the IP address and your PC will execute web browser like IE ,Firefox or
Google Chrome and there is wizard pop up to enquire the Username and Password .

Username : admin Password : 12345678

Step 8 : For the WiFi connection by WPS way , user can check here :
Network WiFi Info Profile list

To make this WiFi IP Address can be found on Internet, please arrange 2 settings as log in the
IPM-401W webpage:

st

1

: Please go to “ Network Setting Default gateway Setting “ and change as WiFi for the

Default gateway Setting .

- 14 -

nd

2

: Please do the port mapping / port forwarding in your router ( Need to check the router

manual ).

Connection by LAN –Network cable

User can also use LAN network cable to connect IPM-401W .
Please refer following steps to setup LAN connection
Step 1: Connect the LAN cable to IPM-401W .The LAN cable should be connected to a Router /

HUB + Router.
Step: 2 : Connect power cable to IPM-401W and Power on the IPM-401W .There is one short

beep in 45 seconds after IPM-401W power up .The short beep means IPM-401W boot up
successfully

Step 3 : After hear the one short beep , please execute IPEDIT.exe . There is IP address of
IPM-401W showed in the right side of IPEDIT.exe following :

Step 7 : Double click the IP address and your PC will execute web browser like IE ,Firefox or
Google Chrome and there is wizard pop up which inquire username and password .

Username : admin
Password : 12345678

- 15 -

About IPEDIT

IP Edit is a search tool designed to search, configure, or access the IP Power IPM-401W from a
local networked computer.

IP Power IPM-401W Default Login / Password
Default IP: 192.168.1.168 (When no DHCP is apparent)

Default Login: admin
Default Password: 12345678

1.) In the local devices section you will see your device show up if connected correctly.

2.) Select the IPM-401W device and the device information will pop up on the right.

3.) Check to see that the gateway IP and the IP Address (IPM-401W) match your current

network. If not, type in the correct information, then hit the submit button to save changes.

For example:
If you have the following information regarding the IPM-401W and your network

- 16 -

Your PC Network :
Computer IP Address: 192.168.1.122
Gateway: 192.168.1.1
Sub Net mask: 255.255.255.0
Port: 80

Your IPM-401W in IPEDIT :
IPM-401W IP Address: 192.168.100.34
Gateway: 192.168.100.1
Sub Net mask: 255.255.0.0
Port: 80

Since the IP Address of the IPM-401W is : 192.168.100.34

You will need to make sure that the first 3 segments of your IPM-401W IP
Address must match the first 3 segments of your gateway IP.

First 3 Segment of Gateway Address: 192.168.1.X
So your new IP Address for the IPM-401W should be: 192.168.1.XXX

New Network Information
IPM-401W IP Address: 192.168.1.26

Gateway Address: 192.168.1.1
Local Computer IP Address: 192.168.1.122
Sub Net mask: 255.255.255.0
Port: 80

4.) Press the rescan button to see if changes have been made.

5.) Double click on the device in the local device section and an IE web browser

with the device login will pop up.

6.) Type in the default Login and IP Address to enter the device.

Default Login : admin
Default : 12345678

Notice :

* User can click " REF " in IEPDIT to auto search proper IP setting for IPM-

401W. It will take few minutes to show the suggest wizard.

- 17 -

Please click APPLY as seeing the suggest wizard , click " yes " to ignore the remind
message of IP being used and then type the username and password to change the IP setting.

Username : admin
Password : 12345678

Internet Setup

To connect the IP Power IPM-401W on Internet, there are two ways



Setup Port Mapping / Port Forwarding in your router. Please check your Router owner‟s
manual .



Use software “ IP Power Center “ : Please refer to owner‟s manual in CD of IPM-401W .

Using IP Server

IP Server is a function which allows you to search for the device easily without having to
remember long complicated IP address. Instead, if you know the device‟s name of your IP
Power device and you can easily find IP Address with IP Service.

In the IP IPM-401W under the system configuration page, you can select the IP Server that
you would like the IPM-401W to go for . You can select from the server or the Cloud Server.
This function must be turned on to work.

* IP Power IPM-401W must be port forwarded for IP Server to work correctly.

- 18 -

1.) Open IP Edit and select the server that your IPM-401W is designated to.

2.) Hit the Green Connect button on the top of IPEdit.

3.) Then type in the IPM-401W Name that you have selected for the device and press the

Search button.

4.) Find your device and double click on the screen and a IE window will pop up connecting to

your device. *Your device must be Port Forwarded for the login screen to appear.

- 19 -

5.) After you have connected to your device, type in the Login and Password for your device

Web Interface

Connect to your Device

Once the IPM-401W has been setup correctly, log into the device.
First Option

1.) Go to IP EDIT find the device that is being used

2.) Double click on the device linked and an IE window will appear with the loading screen

Second Option

1.) Open Internet Explorer type in the IP Address of the device followed by the : sign.
For example: http:192.168.122.188:9258

192.168.122.188 – IP Address
9258 – Port

2.) Once you have typed in the IP address of the IPM-401W and it is ready to use.

- 20 -

The default password for the IPM-401W

Username : admin
Password: 12345678

The Control Console

The Right Panel of the Web Interface controls the functionality and setup of the IP Power IPM­401W.

- 21 -

The IP Power IPM-401W Console consists of six main sections which will be explained in details
below.



PC Mode / Mobile Mode



Time :



Temp & Current :



IO Control :

Controls
Scheduler
Ping
Time Line ( for Current )
History ( Current Setting )



Setting : Internet Status
WiFi Info
WiFi Survey
WPS



Email
DDNS
SNMP
IP Server
Web Camera

Network :

Application



System

Management
Sys Information
Sys Log
Firmware



Logout

Device name , PC / Mobile Mode :

This section show the device name and switch of PC / Mobile mode

Device name :

You can change the device name here : Application IP Server Device name
Change name “ IP POWER IPM-401W “ as “Enjoy IPM-401W “

Please change the name in English only and do not use symbol like !@#$%^&*()_+

- 22 -

PC / Mobile mode

For smart phone user to control IPM-401W Easily , there are different webpage for PC and for
smart phone :



PC Mode : For PC user

All the complete function of IPM-401W can be found in PC model.

- 23 -



Mobile model : For smart phone user

In Mobile mode, user can see the consumption of the current amp , control the ON/OFF status
and adjust the maximum current limit of each port and

- 24 -

Time :

This section showed the time.

To amend the time , Please go to “ System Management NTP Settings

Temp & Current :

This section showed the consumed current ( ampere) of each power and the internal
temperature which display as ゜F or ﾟ C . ) ( F = Fahrenheit , C = Celsius )

IO Control :

The IO Control Section allows you to directly / automatically control the outlets of the IPM-401W
as well as schedule daily, weekly, and monthly power cycles.

There are 5 segments : Controls , Schedule , Ping , Timeline and History.

- 25 -

Control

The Power Controls page allows you to setup the name of each port, control each power or all
the 4 powers ,ON / OFF enable alarm as outlet status change , and also the power status as
Reboot.



Name: User can name each power by click the name above the power button

- 26 -



Controls: The control section will allow you to turn ON or turn OFF each outlet



Group Setting : The control section allow you to turn on or turn off 4 outlets at same time

Please click “Apply “ after select ON/OFF of each port .



Alarm Setting : The control section allow you set alarm by Email / Beep sound.

To get Email about of power status , please go to “ Application Email.



Power On Reset : The control section allow you to set the power status on ON or OFF when
the device power Reboot .

The alarm section allows the IPM-401W to notify you when an outlet has been turned ON
or OFF. There are two ways that you can be notified either by E-mail or by a beeping
sound.

After click “ Apply “ , the webpage will refresh and you can see the final setting result.

- 27 -

Schedule

The scheduler allows you to power devices or turn them ON/OFF a planned scheduled time or
basis.

Adding a scheduled event

1.

Select the action Cycle :

There are 3 selections - Once , Every Day . Every Week

- 28 -

2.

Select the Date and Time : By click the calendar

Select a specific date range where the device will repeat the desired actions during the

time specified.

3.

Choose the Action : Enable power # by chuck in the square , select power action as

One the scheduler has been setup , hit the ADD button and you will see your setting located on
the bottom of the Action section .

- 29 -

Edit a schedule event :

1.

2.

3.

Please click EDIT bottom of that schedule need revise

then change the setting of Cycle, Time , and Action .
Press Add button to confirm the setting and you will see the page refresh and new setting
display in Scheduler list

- 30 -

Removing a Scheduled Event :
Please click Delete button of that schedule need remove .

Ping

The ping function on IPM-401W allows the device to automatically Ping an IP Address to act as
a watchdog to make sure the device getting Pinged is working properly.

Let‟s start by describing the sections of the Ping Interface.

Note : One power can only accept one ping setting

- 31 -

Please click the “ Ping Config setting “ and then show out the setting section.

1.

Base Setting : For all 4 powers



Ping Interval (Seconds): The number of seconds between each ping . Value range at 0 ~ 600

Ping Echo Wait (Milliseconds): The number of milliseconds the device will wait for a

response from the pinged device if no ping is detected within this time it will be considered a
ping failure. Value range at 0~60000

This 2 settings are for all 4 powers .

- 32 -

2.

Ping Setting :



No. : The number of which power to use Ping function



Ping Action : Stop and Continue ping after the action is activated .



IP & Host Name : Input the IP Address ( ex: 122.116.123.138) or

web address (eee.google.com) of the IP you would like to ping.

Select the action that you would like the Ping Function to use when the

device being Ping cannot be located or is not responding. User can use
the “ ping test “ bottom to check the address valid or not



Ping Failure: The number of ping failures before the Action is activated. The setting times
rage is 1 to 99. Select the number of Ping Failures that you would like to occur before the
action is activated. The reddish pink number to the right represents the actual number of ping
failures. Keep in mind that four consecutive pings equals to 1 Ping failure.



Mode : User can select the action was activated by one / two IP Host fail or either one fail

( Mode OR) or both fail ( Mode AND ) .

None : Only ping one Host IP. Action( Power ON/OFF/RESET) will be activated .

OR : IPM-401W will Ping 2 IP address. Either one IP fail times up to the setting times in

“Ping

Failure “ . Action (ON/OFF/RESET) will be activated .

- 33 -

AND : IPM-401W will Ping 2 IP address. Both IP fail depends on the setting times in

“Ping

Failure . Action (ON/OFF/RESET) will be activated.

3.

Action ( Ping Section )

When the number of Ping Failures have been reached. The device can be set to perform a ON,

OFF or Reset function



Enable section : Select the power to activate as ping fails by the mark “ v ” in the small box



Reset: Can set up the time gap of OFF to ON. The “ Sec “ section is for action as Reset only

- 34 -

Timeline

To see this section display normally, please do use IE9.0 or above, Firefox,
Google Chrome or Safari and set resolution at 1280*768 .

This section is for monitor the Ampere ( =Amp ) value each power consumed and is for setup the
maximum value of each power . The maximum Amp of each power is 10Amp. User can click the
“Up / Down “ button directly to change the maximum Amp value of each power.

There is information board show “ Time, Current Limit , Power name and the value of consumed
current “ as move the mouse in the chart .

Display Interface:



A. Clock section :
In this section , user can get the consumed current of each port in chart & word, and directly
setup the max. limit current of each output .

A-1

: In the following chart , it shows different of the max. limit of current .

Channel Name

Green area: Consumed current
It showed 1Amp in this picture.

+ - : Press + or - to directly adjust the max.

current limit. Range at 0~10amp

Current Amp display in word
If showed “OFF” , it means the outlet is turn off

Max. Current limit.

- 35 -

Power 1 : Max. current limit as 10amp. The consumed current now is 1A
Power 2 : Max. current limit as 9 amp. The consumed current now is 0A. ( Output turn ON )
Power 3 : Max. current limit as 7amp. The output is turn off.
Power 4 : Max. current limit as 3amp. The output is turn off.

Note : If the detected current output power 1 is over the max. limit current value setting,
then power 1 will turn off automatically in few second .

A-2

:

The Triangle in the middle of chart will keep circling means the current is keep consuming.

B.

Curve Chart section :
In this section, user can see the consumed current value with live update chart while time past
show from time to time .

B-1 In X axis - horizon , it show time in second . In Y axis – vertical , it shows current value

in ampere.

User can see the consumed ampere from past 15 seconds in the chart.

The default maximum time showed in the chart is 30 seconds and 10 amp.

B-2 User can adjust the Current display range by pressing the + / - button at right side

as following : .

- 36 -

B-3
show on chart . To go back to original display as 10 seconds , please click “Current Limit” of
IO Control section at left area .

For example :
Select the range time by mouse - keep clicking left button and and drag select area

User can change the time gap difference by mouse : Select the time area you would like

- 37 -

B-4

As mouse move to the line chart , there is message board shows time, current and

consumed power current in a square as following:

Over Current Protection ( Max. Current limit )

There has over current protection in IPM-401W. As the Amp value of power A is over the setting or
over the maximum value 10 Amp, IPM-401W will automatically turn off that power A in few seconds
.

There is an alarm with beep sound and via e-mail advice as over current. The alarm can be
enable or disable for each power in Alarm setting of Power Control in IO Control section.

As the detected Amp value is over the current limit setting, IPM-401W will keep short 2 beep
for several times to remind the over loading issue happened and then turn off that output after
a long beeping .

- 38 -

History :

To see this section display, please do use IE9.0 or above or Firefox . and set
resolution at 1280*768 .

User can see the power usage history around one year in this section.
Note : The history will be deleted after device power Reboot .

This section display the “ Current Ampere “ usage of each power and the “Temperature” value
„ .

Before check the chart please do select the Voltage of your environment :

Please click the area to change the City Voltage between 110 / 120 / 220 / 240 V

- 39 -

In Power Usage Chart ( Up chart ) :

A.

There are 4 color coding round signs on the left side show the total WH ( Watt –Hour) of

each power consumption in select area. User can move the 2 time gap sign to get

the total consumed WH value of the select time range.

For example :
During 2013/03/29 13:38 ~ 13:44 ,the total WH of Power 1 consumed is 0.0485WH.

B.

Life update information :

Show the total power usage in WH during the time.

- 40 -

C.

Power Usage Chart

There are different color show each power :

Power 1 : Pink Power 2 : Blue

Power 3 : Green Power 4 : Yellow
In the chart :
X Axis – horizon : Show Date and Time ( HH/MM/SS)

Y Axis– vertical : Show Ampere ( A ) of each power consumption

For example : On 2013/3/29 14:09:09 ( HH/MM/SS ) , Power 1 consumed 1.9 A and the total
amp of 4 power is 1.9A.

For example :
On 2013/3/29 15:22:35 ( HH/MM/SS ) , Power 1 consumed 1.9 A , Power 2 consumed 2.1A ,
Power 3 consumed 0.38A , Power 4 consumed 0.97A . Total 4 ports consumed 5.35A.

To close this Current History Wizard and go back to control section , please move the mouse to
the gray area out of this Current History Wizard and click then you can go back to control section .

- 41 -

Note: The current history record will be cleared off the chart while device power off .

Network :

Setting

This section is showed the network status of IPM-401W .
There is 4 different portions in this section :



ETH Connection : LAN / Cable connection



WiFi Network Setting : WiFi connection



Default Gate way : Can change the gateway of LAN or gate way of WiFi



Port Setting : use can set port range as 80 ~65535

- 42 -

There are 2 portions : Ethernet & WiFi connection type.
 ETH ( Ethernet ) Connection type : The network status is connected by

cable

The connection way include : Static IP / DHCP / PPPOE

 WiFi Connection type : The network status is connected by WiFi

 The connection way include : Static IP / DHCP

- 43 -

User can select different way for Ethernet Connection or for WiFi connection .
STATIC (fixed IP) :

Setup IP address manually. This allows the 9258WiFi to obtain an IP Address automatically from
user`s server connected to Internet . Recommended for users need to control through Internet.

Please do filled the correct gateway for login from Internet .

DHCP Mode :

Obtain IP address via DHCP model . This allows the 9258WiFi to obtain an IP Address
automatically from user`s server connected to Internet . Recommended for non advance users.

User can only revise the Host Name under DHCP mode.

PPPOE :

Only support for Ethernet connection .
Obtain IP address via Internet Service Provider (ISP) through PPPOE service ( The IP address
can be reach on Internet but not fixed ) . User need to supply the Username & Password ISP
supply to get connection on Internet.

- 44 -

User Name : Please type in the format ISP supply for PPPOE connection
Password : Please type in the format ISP supply for PPPOE connection
Verify Password : Re-type the password
Operation Model : There are 3 mode for PPPOE connection



Keep Alive : Auto connection as disconnect . Can setup the redial period in seconds .



On Demand : Auto connection as disconnect and can setup the idle time in minutes.



Manual : Connection ISP manually ( type Apply ) .

Default Gateway

The gateway is the door for Internet connection.
Please select LAN or WAN for the user to log in IPM-401W form Internet.

There is only one gate way available : LAN or WAN.

Under DHCP model - either ETH Connection type or WiFi connection type ) , IPM­401W will get the gateway information automatically.

But if under Static model , please do filled the correct gateway.

If choose WiFi the gateway of LAN will be empty automatically. Please refer the following
illustration :

- 45 -

LAN Internet

IPM-401W will check your router IP of this connection , and you can separate the port for LAN
connection or for Internet connection .

For example : The router IP is 36.224.37.128:80

- 46 -

WiFi Information

This section is displayed the WiFi information and also the Profile list :
WiFi Information Section :

MAC Address : There are 12 digits for IPM-401W as Identity number.
Local IP Address : It show the IP of WiFi connection ( Allocate Supply by WiFi Router )
Connection Status : It show the router name of IPM-401W is connected.

If need to add other WiFi Router into profile list , please arrange the WiFi connection setup ,
please go to “ WiFi Site Survey “ but user can change the profile list to switch the WiFi Router
you would like to use.

As connection successful , there is green check mark in first column of the profile Router.

WiFi Site Survey

This section is to arrange WiFi connection. IPM-401W will auto search the WiFi Router nearby
and also their information as boot up , IPM-401W user can just select the router and type the
password to connect with your WiFi router and make connection easily.

Add WiFi Router into “ Profile list “ :

Step 1: Select the Router you would like to use , and click “Add Profile “

- 47 -

Step 2 : IPM-401W will auto get the most information of your router and you just need to type
the password to connect with the WiFi router then click “ Apply “

Then you will see the Router name “ qatest “: add in to “Profile list “

- 48 -

Connect IPM-401W to this add Router : Active the WiFi Router in “ Profile list “

Please select the router an click “Active “ to make connection with IPM-401W.

Step 4 : After Active successful , you will see the IP information in “ Connection Status “ of
WiFi Info. Please check if the “ Local IP Address “ of WiFi Info is under same segment# with
your PC.

Notice :
# Segment : The first 9 digits of the IP Address .

EX: The IP of your PC is 192.168.100.122. If the “ Local IP Address “ at WiFi Info is

192.168.100. x ( X can the value of 1~252 ) , your PC can get into the webpage of IPM­401W .

# Please press “Rescan “ to search the router near by again if can not see your router in the list.

- 49 -

Delete the Router in “ Profile list “ :

Please select the router and click “ Delete “ to remove this router from “ Profile list ”
Note : Delete the Router form Pro File list do not affect the connection of WiFi.

WPS ( WiFi Protection Service )

There is 2 way to setup by WPS :
Manual hardware setting connection or webpage application

The following information is for apply WPS by webpage control – without WiFi Router nearby .

By the Button on IPM-401W and on WIFI AP ( Router)

Please refer the manual hardware operation in page #15

By Enrolee of IPM-401W and WPS button on WIFI AP ( Router)

Step 1: Please select the WIFI AP ( Router ) you want to connect .

Step 2 : Select Mode “Enrollee “ and press “PBC Start “ and then press the WPS buttons on
WIFI AP ( Router) soon in few seconds.

- 50 -

Step 3: After few seconds , there are 2 beeps : short Beep + middle beep
Which means WPS connection successfully.

There are messages updated during the configuration in “ WPS status “ section :
As WPS connection successfully , there is “Configured “ message as following :

If user does not press the WPS function of selected AP ( WiFi Router )
SCAN AP ……PCB: NO AP (one Long Beep) No Used
Which means the WPS connection fail and there is one long beep mean the connection fail.

Please try again. )

Step: 4 : You can see the WPS connection in section “ WiFi Info “ & “ WiFi Survey “ of Network
In “ WiFi Survey “

- 51 -

By Registrar

Step 1 : Select the router you want to connect .

Step 2 : Select “Registrar “ and Type the PIN number supply by your WIFI AP ( Router )

- 52 -

into Pin area and then press button “Pin Start “ then you will see “Configured “ in WPS status
as connect successfully.

Step 3: You can see the WPS connection in section “ WiFi Info “ & “ WIFI Survey “ of Network

- 53 -

Application Settings

Email

In this section, user can setup the e-mail to get advice as each power outlet status changed.
Notice : To send out the email successfully , please double check the setting of your DNS .

(Network DNS setting)

Example: “ On Off “ or “ Off On “ . Please do enable the Email alarm in “ Power Control”

of “ IO Control “ section as following picture :

The IPM-401W allows you to send from @gmail or @hotmail or @yahoo.com account .

- 54 -

From : Mail sender address to send the E-Mail out . Ex: IPM-
[e-mail] To : Mail receiver address to get the E-Mail in Ex:
[e-mail] SMTP Server: This is the mail server of the sender at “ From
“ .

If user select @gmail or @hotmail account as SMTP Server , IPM-401W will fill the SSL & Port
automatically

SSL inquire : If the mail server needs to be authenticated make sure the yes is checked in
Port : This is the port of SMTP Server. Most common port to send out e-mail is port 25

User : Login for the e-mail address . Ex: [e-mail]
Password: Password for the e-mail address. EX : 12345678

Note : To send out the e-mail successfully ,the correct DNS information for setting up is

necessary . Please check your Router or check with your ISP company.

Example :
Send by Gmail account

- 55 -

DDNS

The DDNS section allows you to setup the IPM-401W with a DDNS server (i.e.

www.dyndns.com). After the server has been setup correctly, enter the necessary information

into the IPM-401W DDNS settings.
IPM-401W support 4 DNS server. User need to create its own account in these DNS server

Note : “ Dyndns.org “ is the only one provides free service .
The other’s 3 server may change user for the DDNS service as apply account.

Account : the username /account name of DDNS account
PassWord : the password of DDNS account
DDNS : The DDNS name you apply . Ex: abc.dyndns.org

For Example :

- 56 -

SNMP

This section is for development of system integrator who familiar with SNMP knowledge.

IP SERVER

In this section , use can setup IP Server function ( & CNT – Cross Network Technology )
And get QR code of IPM-401W

IP Server & CNT :

The IP SERVER allow IPM-401W to be easily accessed on the internet by our IP Power Center
or IP EDIT. With this feature anyone can find there device with no problems.

IP Server: Allows you can find your IPM-401W on the internet without having to remember long IP
Addresses. Instead you can just remember the name of your device.

- 57 -



Enable IP Server : Enable or disable this function chuck .



IP Server & CNT Server : For easily setting , Please select same server number for the 2

part.
User can search the IPM-401W by Device name , Country or City.
This allows the device to easily be accessed on the internet, you no longer have to port forward

your device to be able to use it. Only some devices are CNT compatible.
Please refer page #20 for the function of IP Server

QR code of IPM-401W :

User can create own QR code of the IP information of IPM-401W ( LAN / WIFI / Internet),
and scan / record in your QR code APP for quick search or log in IPM-401W .

Please make sure to do port forwarding ( local port and forwarding port must be same
port ) if need to get the QR code which can directly go to the webpage of IPM-401W
on Internet

 QR Code in IPM-401W webpage

This QR code help user to get in the webpage IP address IPM-401W by smart phone
quickly. There is history in QR code app for user to check IPM-401W IP soon .

- 58 -

-

To view the IPM-401W webpage on Internet , please do “ port forwarding “ first in router.

-

To view the IPM-401W webpage on LAN , please make sure your smart phone is under
same segment ( refer Page#17 , you will need to make sure that the first 3 segments of
your IPM-401W IP Address must match the first 3 segments of your gateway IP. )

Please select the QR code of IP Information from Internet, LAN, WAN & IP Server.
And then press “Apply to create new QR code.

# Internet: It will create QR code with the Internet IP of the environment of IPM­401W . ( need port forwarding ) .

# WAN / LAN: It will create QR code with the WAN/LAN IP of IPM-401W .
# IP Server : Please enable “IP Server function first and then it will create QR code with the

MAC for user to use IP Server ( of IPEDIT ) in your smart phone .

 QR Code in IP Server :

Before get the QR code in IP Server , please make sure the IP Service is enable in IPM­401W webpage.

IP Server : With our OWN CNT function , user can easily get the Internet IP by IPEDIT

Please go to our online IPEDIT : www.myipedit.com

Them please select “ Server 2 “ and type the device name ( if change) or IPM-401W.

- 59 -

USB WebCam

This section allow user to connect USB Webcam ( with UPNP function , M-JPG / YUV format )
and view the webcam in IPM-401W webpage directly. To work with IPM-401W, the USB Webcam
need to support UPNP and video as M-JPEG or YUV format to view the area near IPM-401W.

Note : The JAVA version should be 1.60 or above for USB Webcam view under web browser

Internet Explorer -IE and the gateway setting must be correct - WAN or LAN as port forwarding
and view on Internet

- 60 -

- 61 -

System Setting

Management

In this section there are several setting :
Administrator setting, NTP setting ,Export Setting , Import Setting , Load Factory Default ,
Restart System

Administrator setting

The User Management section allows you to create users that will be able to access your device.
There are two main types of users:

There are three Authorities in IPM-401W. The account name and password can be changed
by user but each Authorities only support one Account name & one password.

Administrator: The Administrator has the authority to create other users, remove users, and
control the device. IPM-401W will asked to log in again as change the default setting here.

Operator : The operator can only control the setting of “ IO Control “ section but can not see
other page of IPM-401W .

Viewer : The viewer can only see the “ IO Control “ section but can not see other page of IPM-
401W.

- 62 -

Default Setting of the authorities :

Authority

Account name

Password

Admin

Admin

12345678

Operator

user

user

Viewer

guest

guest

Note

Please amend the password as number or English character from
1 to 8 characters.

Do not use special sign like “ ” ; ： ~ ! @ # $ % ^ & * ( )

Please click “Apply “ button “ after change the account name / password

NTP setting
In this section , user can setup the date , time and NTP server to get the time synchronization .

NTP synchronization : User can setup the time gap ( 1~300 hours ) for IPM-401W to check
the time with the NET server .

Export Setting

User can export the setting of IPM-401W into a “ DAT “
format . It will save most the setting in IPM-401W .

Import Setting

User can import the file which was exported from IPM-401W as “ DAT “

format . It will help user to setup many IPM-401W device in a short time.

As press “ Import “, there is caution message show as following :

- 63 -

Before click ok to import please do read following notice :



Do NOT import DAT file which is not export form IPM-401W. It is out of warranty support if
any damage by import .



Please do import the file in LAN / Ethernet . To avoid import fail , please do not import file by
Internet

Load Factory Default & Restart System

In this 2 section , user can click one button to set back the setting to default or restart the IPM­401W without device nearby your side.

Note : The factory default setting of IPM-401W IP is assigned by DHCP. It will change the
IP if load factory defaults .

- 64 -

System Information

In this section , user can get the system information :

- 65 -

System Log

In this section , user can get the system log of IPM-401W. The system information will be
deleted after IPM-401W device power reboot.

Firmware

To update the IPM-401W , please follow the instruction below to prevent anything happens like
update incomplete or hardware disable which may be caused by wrongdoing of updating :

1)

Turn off all chat programs including ( Skype, FB. QQ, AIM, Yahoo messenger ….etc.) to

prevent conflicts

2)

Check to make sure that all devices are safety turned on and powered

3)

While updating do not turn off the power

4)

Make sure that the cable is connected firmly

5)

Do not interrupt the update process, the update must be completely finished before using the

device

6)

Turn off, any Spyware or antivirus software which may conflict with the update.

7)

Update firmware in the Local Area Network (LAN)

8)

Support update under Web Browser like IE, Google Chrome, Firefox under WIN 7 - 32bit

& WIN XP . Do not support Browser under WIN 7 - 64Bit

9)

Please change the PORT as 80

10)

Re-start the device

Please also update the notice in webpage before update :

- 66 -

Controlling the Device

By IR Remote Controller

To control IPM-401W by IR remote power controller we supplied, please use 5 buttons in this
remote controller : Power button , button #1~# 4



Enable remote controller : Press Power button one time and IPM-401W will response a
short beep which mean the remote control function enable .



Disable remote controller : After enable the function , then pres Power button one time
again , then IPM-401W will response 2 short beep which mean the remote control
function disable.



Outlet ON/OFF control : Press the Button #1 ~#4 to turn output 1~ 4 ON / OFF .

- 67 -

CGI HTTP Commands

CGI Commands allow you to easily integrate the IPM-401W with other systems and programs.
Please read the instructions carefully on how to use the Http:// Commands

To use http:// Commands open up a web browser and type in the command that you would like to
use.

1. User authorization .There are 3 formats :

For example : IP address 192.168.1.18 ，Username : admin. Password : 12345678

1.1 http://admin:12345678@192.168.1.18/set.cmd?cmd=getpower

1.2 http://192.168.1.18/set.cmd?user=admin+pass=12345678+cmd=getpower
The above 2 way also for HTTPS

2. Command
set.cmd?cmd=

All command do not separate capital / lower case , the connect symble between

commands can be “+” ，“&” and “?”.

2.1 To get firmware version : getversion

http://192.168.1.18/set.cmd?cmd=getversion

System return :
CGI Command : Data follows
Version=9258W_N_v1.0.0.1

2.2 To get MACaddress：getmac

http://192.168.1.18/set.cmd?cmd=getmac

System return：
CGI Command : Data follows

mac=00929000008F

2.3 To get the status of power on/ off： getpower

http://192.168.1.18/set.cmd?cmd=getpower

System return：

CGI Command : Data follows
p61=0, p62=0, p63=0, p64=0
P61 to P64 means : POWER1 to POWER4

2.4 To get Current ： getcurrent

http://192.168.1.18/set.cmd?cmd=getcurrent

- 68 -

System return：
CGI Command : Data follows

c61=0.000000, c62=0.000000, c63=0.000000, c64=0.000000, temp=22.700001
C61 to C64 means 4 currents ，temp is temperature （as Celsius ）

2.5 To get temperature （Celsius）: gettemp

http://192.168.1.150/set.cmd?cmd=gettemp

System return：
CGI Command : Data follows

temperature=22.700001

2.6 To set the power on / off ：setpower&p6x=0 or 1
p6x=0 means off，p6x=1means ON，x can be 1 to 4 ( power1 to power 4)
Example : Turn on POWER1 and POWER2 and turn off POWER3：

http://192.168.1.18/set.cmd?cmd=setpower&p61=1&p62=1&p63=0

System return：
CGI Command : Data follows
p61=1,p62=1,p63=0

2.7 Setup power to reboot as RESET：setpowercycle& p6x=delayTime
X can be 1to 4 ( power 1 to power 4 ) ，；dealyTime mean the time ( second) waiting

for reset

For example :

http://192.168.1.18/set.cmd?cmd=setpowercycle &p61=5&p62=2&p63=4

System return：
CGI Command : Data follows

p61 cycle ok,p62 cycle ok,p63 cycle ok

- 69 -

Telnet Control

- 70 -

FAQ :

Q1: Why can I see 2 IP address on IPEDIT.exe but can only reach one ?

Why did IPEIDT.exe show the LAN IP address as no network cable connect ?
Why did IPEDIT.exe show the WIFI IP address as no WIFI router available ?

A1: IPM-401W will remember the LAN / WAN setting one connect .Please select the IP you can
log into IPM-401W to operate.

There is no problem if connect both LAN and WAN

But the Gateway setting will affect as working on Internet and also sending / receiving
email . User should select the correct Gateway as need to get into IPM-401W on Internet

Q2 : Why can`t I see my IPM-401W after arrange the port forwarding in my router?

A2 : Please make sure the Gateway is correct Gateway ( LAN or WAN )

Q3 : Why can`t I receive email ?
A3: Please check the setting first and then make sure the DNS is correct ( Check your router /

asked your ISP company ) .There is test button for checking the the setting success or fail to
send mail.

Q4 : Why can`t I see the current chart ?
A4 : Please check the web browser version . Need IE 9.0 or above version

To see this section display normally, please do use IE9.0 or above, Firefox,
Google Chrome or Safari and set resolution at 1280*768 .

Q5: Why can`t I get the IP in IPEDIT by LAN after delete WIFI profile or lost WIFI AP
connection ?

A5: If the WiFi connection for IPM-401W lost or the WiFi AP router damage,
IPM-401W can not get the WiFi IP then it will change it`s IP to fixed IP address as

192.168.1.168 . User can not see the IP by IPEDIT as the Gateway is still at EiFi .

At this time , there are 2 ways re-log in IPM-401W . :
BY WiFi connection : Please reboot 9258W and Re-connect IPM-401W with new WiFi router

by “ WPS “ button ( can do this way without 9258 W2 power reboot )
BY LAN connection :
Please refer following step :

- 71 -

Step1: Please connect IPM-401W to your PC directly and change the IP address of your PC
as 192.168.1.xxx ( set the IP of your PC to be the same segment of IPM-401W . )
xxx can be 1~255 but not 168 .

Step 2 : After log in to the IPM-401W in LAN, please go to
Network Setting Default gateway setting to change the Gateway from “ WiFi ” to “ LAN
“ and click “Apply” .

Step 3 : Connect your PC and IPM-401W to a router by LAN. Then reboot IPM-401W (MUST

DO) . After 45 seconds with a long beep, you can found the LAN IP of IPM-401W by IPEIDT.exe

Q6: How can I reset to default:

A6 : Please use tiny pin head and keep pressing the button “RESET for 5 seconds at least and
release , there is a long beep sound after around 45 seconds . Then please power reboot the
IPM-401W . after around 45 seconds there is a middle beep sound then you can use IPEDIT to
hekc
which means system reboot successfully and set back to default.

Q7 : Why can`t I see the video of USB Webcam in IPM-401W webpage ?
A7 :
Please check the following premises :
Please make sure the setting of “Capability “ is “Enable “

-

The USB WebCam support UPNP connection and support M-JPG or YUV format .

-

The web browser is IE 9.0 at lest or above .

-

The JAVA version is 1.60 or above

-

The gateway setting is correct - WAN or LAN to view on Internet