XtendLan HDC-SDOMEO51MIR-B User Manual

HDC-SDOMEO51MIR-B
USER MANUAL
HD Portable Rugged PTZ Cameras
Safety Notes
Thank You for Choosing Our HD table Rugged PTZ Camera!
When you open the box:
1. Check that the packing and the contents are not visibly damaged. Contact the retailer immediately if any parts are either missing or damaged.
2. Make sure if the contents are all included as per the packing list.
3. Do not attempt to use the device with missing or damaged parts. Send the product back in its original packing if it is damaged.
[Note] The information contained in the document is subject to change without notice.
Table of Contents
Safety Notes --- Important!!! ........................................................................... 1
About The Product .......................................................................................... 2
Features ......................................................................................................... 2
Functions ........................................................................................................ 3
Technical Data ............................................................................................... 5
Preparation....................................................................................................... 7
Dip Switch ....................................................................................................... 7
Initial Power On Test ...................................................................................... 9
Installation Place ............................................................................................ 9
Installation .................................................................................................... 10
Magnetic Mount .............................................................................................11
Installation .....................................................................................................11
Camera Cable Package ................................................................................14
Operation ...................................................................................................... 16
Special Control Panel Commands ................................................................16
Operation .......................................................................................................17
1
Safety Notes --- Important!!!
The following important notes must be followed carefully to run the camera and respective accessories in total safety. The camera and relative accessories are called video system in this section.
Before installing the camera, please read this manual carefully; when installing, please follow
instructions of installation indicated in this manual. Please keep this manual for future use.
The following installation should be performed by qualified service personnel or system installers
in accordance with all local rules.
Before powering on the camera, please check the power voltage carefully. Make sure that you
are using the right power source.
Please put the power cable, video cable and control cable in safe place. Do not operate the camera beyond the specified temperature and humidity. The camera’s
working temperature range is between -35~+65. The ambient humidity range is less than 95%.
When transporting, avoid violent shake or force to the camera. To prevent electric shock, do not remove screws or covers of the camera. There are no
self-serviceable parts inside. Refer to qualified service personnel for servicing.
Video cable and RS485 cable should be far away from other cables. Shielded and independent
wiring is necessary for video and control cables.
Never aim the lens of the camera at the sun or other extremely bright objects. Otherwise, it may
cause damage.
When cleaning the camera, please use soft cloth. If the camera is very dirty, wipe it off gently
with a soft cloth moistened with a weak solution of water and a neutral kitchen detergent. Wring all liquid from the cloth before wiping the camera, then wipe off all remaining dirt with a soft, dry cloth. Use lens cleaning paper to clean the lens.
Do not move the camera module manually. In doing so would result in malfunction of the
camera.
Do not hold the camera module when carrying the video camera. Make sure the camera is far away from area where radiation, X-rays, strong electric waves, or
magnetism is generated.
With its stability, easy-to-use and excellent performance, it is widely used in electronic classroom,
technical training and video conferencing room, etc.
2
About The Product
The portable rugged PTZ camera is designed for practical and extreme applications, such as military field surveillance, security outdoor evidencing etc. It is featured as weather-proof, anti-vibration and anti-corrosion.
It can be deployed into a mobile surveillance system, consisting of ptz camera, vehicle video recorder, monitor, control system and 3G wireless video transmitter. Meanwhile a remote controller is available for the user inside the vehicle to control the camera outside.
Features
2.2MP, 1/3 HD CMOS sensor; Support 1080P, 1080i, 720P and standard definition video outputs; Simultaneous video outputs via HD-SDI and CVBS interfaces; Efficient 60M IR / White Light lighting, excellent night vision performance; Magnesium Alloy front cover; Portable with compact design & high reliability; Advanced mechanical system with high speed and free-maintenance motor design; Optional damping system; Digital Image Stabilization (DIS) supported; WDR supported; Built in defogger; Soft address supported; Self-adaption of Protocol (Pelco D/P) & Baud rate; Support VISCA protocol; Wide range of voltage input (10.8-28V); Auto power-off with low power supply; Random Scan, Auto Scan, Frame Scan supported.
3
About The Product
Functions
Soft Address
The camera address can be programmed with a preset command, and the user does not need to dismount the camera from field or do any screw work.
Self-Adaption of Protocol and Baud Rate
The camera can automatically identify the protocol (Pelco D/P) and baud rate of the controller and adapt the camera setting accordingly, with no manual DIP Switch involved.
Day/Night Function
The IR cut filter of camera module inside the camera can be removed by sending special command, so that the camera can change from color to mono. The picture is clear even if the illumination is as low as 0.1Lux.
Save/Call Preset
Preset function is that dome saves current horizontal angle and title angle of pan/tilt, zoom and position parameters into memory. When necessary dome calls these parameters and adjusts Pan/Tilt and camera to that position. User can save and call presets easily and promptly by using keyboard controller or infrared controller. The camera supports up to 256 presets.
Zoom control
User can adjust zoom wide or tele by controller and get desired image.
Focus control
System defaults Auto Focus mode, that is, the lens and camera will automatically adjust the focus to get the best image.
Focus can also be controlled manually from the controller if required. Press Focus Near or Focus Far key to manually focus. Focus can be manual via keyboard or other controller, please refer to control keyboard or other controller operation manual for detailed operation.
The camera will NOT auto focus in the following status.
4
About The Product
Target is not in the center of image. Targets are in near and far at the same time. Target is of strong light object. Such as spotlight etc. Target is behind the glass with water drop or dust. Target moves too fast. Large area target such as wall. Target is too dark or vague.
IRIS control
System defaults Auto IRIS. Camera can adjust immediately according to the alteration of back ground illumination so that a lightness steady image can be achieved.
You may adjust IRIS by controller to get required image brightness, and call back Auto IRIS by controlling the joystick.
Auto White Balance
Camera can automatically adjust white balance (WB) according to the alteration of background lightness to give a true color image.
Back Light Compensation (BLC)
If a bright backlight presents, the subjects in the picture may appear dark or as a silhouette. Backlight compensation enhances objects in the center of the picture. The camera uses the center of the picture to adjust the IRIS. If there is a bright light source outside this area, it will wash out to white. The camera will adjust the IRIS so that the object in the sensitive area is properly exposed.
Auto Cruise
The preset position is programmed to be recalled in sequence. This feature is called auto cruise.
Auto, Random and Frame Scan
Auto Scan: Make the camera scan 360° ranging from the current position.
Random Scan: Make the camera scan 360º ranging from the current position, pause at every
108º.
5
About The Product
Frame Scan: Make the camera scan between two set positions.
[Note] For Frame Scan: The zoom at two limits shall be programed the same.
Image Flip
Enable you to view image easily when PTZ is either installed on roof of a car or is mounted on the ceiling.
Technical Data
Camera
Image Sensor
1/3”progressive scan CMOS
Effective Pixel
2.2mega pixel
Video Format
HD: 1080p30/1080p25/1080i60/1080i50/720p60/720p50 SD: PAL/NTSC
Video System
PAL/NTSC
Optical Zoom
20X
Digital Zoom
8X
Min Illumination
Color: 1.5Lux @ F1.6(50IRE) B/W: 0.1Lux @ F1.6(50IRE)
White Balance
Auto/ATW
Focus
Auto/Manual
Exposure
Auto/Manual
S/N Ratio
Not less than 50DB
BLC
On/Off
Image Stabilization
On/Off
Day/Night
Yes
Lens
f=4.45mm-89mm, F1.6 to F2.9
View Angle
Horizontal: 56.56º~3.10º, Vertical: 43.32º~2.34 º
PTZ
Pan Range
360° Continuous
Pan Speed
Control speed: 0.05°120°/s, adjustable; Preset speed: 150°/s
Tilt Range
-15°~90° (Auto Flip)
Tilt Speed
Control speed: 0.03 °90 ° /s, adjustable; Preset speed:120°/s
Preset
256
6
About The Product
Preset Precision
±0.05°
Light (for IR Version)
IR Wave Length
850nm
940nm
IR Range
60m
30m
IR Switch
Auto/Manual
Light (for White Light Version)
Color Temperature
6500K
Range
60m
Switch
Manual
General
Comm. Interface
RS-485
Protocol
PELCO-P / PELCO-D, VISCA
Baud Rate
2400bps, 4800bps, 9600bps, 19200bps (self-adaptive)
Address
0-255
Voltage
DC10.8-28V
Power
10W (Standby) 25W (Aux lights ON, defogger ON, and P/T running continuously)
Working Temperature
-35~65
IP Code
IP66, TVS, Anti-surge
Dimensions
Φ130(mm)×173(mm) w/o damper Φ140(mm)×199(mm) with damper
Weight
Standard: 1.6kg With damper 2kg
Table 1: Technical Data
[Note] The specifications are subject to change without notice.
7
Preparation
This section contains detailed instructions for installing the camera. These instructions assume that the installer has a good knowledge of installation techniques and is capable of adopting safe installation methods.
Dip Switch
The factory default is:
Camera Address
Protocol
Baud Rate
1
Pelco D
9600bps
The camera can detect and auto program its protocol (Pelco D, Pelco P) as well as baud rate (2400bps, 4800bps, 9600bps, 19200bps) as per the whole video system. In case of VISCA, it needs to be manually set.
Only the camera address setting is necessary. There are two ways to program camera address:
Soft address: via special preset functions (see Special Control Panel Commands) DIP Switch: The switches to configure these settings are located on the main board inside the
camera. See Fig.1: DIP Switch.
Fig.1: DIP Switch
8
Preparation
SW1
SW Position
1 2 3
4
Camera Address
OFF
OFF
OFF
OFF
0
ON
OFF
OFF
OFF
1
OFF
ON
OFF
OFF
2
ON
ON
OFF
OFF
3
OFF
OFF
ON
OFF
4
ON
OFF
ON
OFF
5
OFF
ON
ON
OFF
6
ON
ON
ON
OFF
7
OFF
OFF
OFF
ON
8
ON
OFF
OFF
ON
9
OFF
ON
OFF
ON
10
ON
ON
OFF
ON
11
OFF
OFF
ON
ON
12
ON
OFF
ON
ON
13
OFF
ON
ON
ON
14
ON
ON
ON
ON
15
SW Position
5
6
Protocol
PELCO_D
OFF
OFF
PELCO_P
ON
OFF
VISCA
OFF
ON
Reserved
ON
ON
SW Position
7
8
Baud Rate
2400bps
OFF
OFF
4800bps
ON
OFF
9600bps
OFF
ON
19200bps
ON
ON
[Note] The camera shall be rebooted after the switches are programmed.
[Note] When protocol is programmed as Pelco_D or Pelco_P, the baud rate can be
self-adaptive. With Visca protocol, the baud rate can be programmed via SW Postion 7 and 8.
9
Preparation
Initial Power On Test
To ensure the camera works well after installation, please power on it for an initial test with the following steps:
1. Connect the camera with correct power supply;
2. Connect control cable, video cable;
3. Power on the camera;
The camera will run a calibration procedure on power up and show the following messages on screen.
DOME ID001 PROTOCOL:PELCO-D/P BAUD9600 SOFTWARE VER1.3
Fig.2: On Screen Messages at Power Up
On the control device, set the protocol Pelco and the camera ID as per the above messages. The PTZ camera can auto detect the protocols and baud rate of the controller and change its own setting accordingly.
Installation Place
Make sure the installation place has enough space, support strength to install the whole PTZ camera and its accessories.
10
Installation
There are two types of mounts: the fixed mount and magnetic mount.
Fig.3: Fixed Mounts (with damping system)
Fig.4: Fixed Mounts (with no damping system)
11
Installation
Magnetic Mount
Fig.5: Magnet Mounts (with no damping system)
Installation
To set the camera hard address:
1. Remove the DIP Switch cover at the bottom;
2. Set DIP Switch for camera address;
3. Fix the cover. Make sure the cover is well sealed with the gasket.
Fig.6: Bottom Plate
12
Installation
Fixed Mounts:
With Damper
1. Take the damper out of packing and fix it to the target place as per the installation dimensions
with correct screws.
Fig.7: Installation Plate
2. Put the camera onto the damper. Make sure three installation bolts are in position with the fixing
holes on the plate. Rotate the camera clockwise.
Fig.8: Mount the Camera
13
Installation
3. Fix the camera to the damper with a screw.
Fig.9: Fix the Camera
With No Damper
1. Take the PTZ camera out of packing and fix it to the target place as per the installation
dimensions with correct screws.
Magnetic Mounts:
1. Take the PTZ camera out of the packing and put it to a metal smooth surface with the magnetic
sucking to the surface firmly.
14
Installation
Fig.10: Fix the Camera
[Note] Please place the ptz camera in a safe place when there is no guard.
Camera Cable Package
Connect the cable with the right pins as per following pictures.
Fig.11: Cable Package
15
Installation
Pin Definition
Pin #
Definition
1
Video +
2
Power -
3
Power +
4
RS485 -
5
RS485 +
6
Video -
[Note] Please make sure the camera is working with a right power supply. Wrong cable
connection may cause damage to the device.
16
Preset Number
Function
Default Value
<20, >82
General preset positions
-
21
Manual switch between color mode and mono mode
-
22
Auto switch between color mode and mono mode (for IR version only)
26
Turn on/off Image Flip;
Off
28
Turn on/off video freeze
Off
29
Turn on/off Digital Image Stabilization (DIS)
Off
32
Turn on IR lights (for IR version only)
-
33
Turn off IR lights (for IR version only)
39
Turn on/off digital zoom
Off
42
Set Left Boundary of Frame Scan
-
43
Set Right Boundary of Frame Scan
-
48
Turn On Random Scan
-
49
Turn On Frame Scan between two set presets
-
50
Turn On Cruise
-
51
Turn On Auto Scan(360° Scan)
-
52
Clear All Presets
-
53
Default Setting
-
62
Decrease The Camera Address By -1
-
63
Increase The Camera Address By +1
-
64
Auto shutter
65
Increase shutter speed
-
66
Decrease shutter speed
-
72
Turn On white lights (for White Light version only)
-
73
Turn Off white lights (for White Light version only)
74 75
76
1080i_50
1080i_60
720P_50
Video Output
77
720P_60
1080i50)
Operation
Special Control Panel Commands
The camera can be programmed and operated using various quick control panel commands.
Formats (Default:
Table 2Special Commands
17
Operation
- indicates current function not set or not open; √” indicates the default setting of current function;“on”indicates the default mode of current function is on;“off”indicates the default mode of
current function is off;
Operation
As the baud rate and protocol are self-adaptive, the PTZ cameras may not response for seconds on power up. It is recognizing the commands and adapting the setting.
IR / White Light
Auto Mode (For IR Version Only):
The default IR mode is auto. Auto mode can also be activated via preset 22. At this mode, the commands of preset 30~33 are disabled.
When the zoom module is in mono, the camera will automatically turn on IR lights. The high beam and low beam will be turned on/off as per the current zoom times.
When the module is in color mode, the camera will automatically turn off IR lights.
Manual Mode:
For IR version: Call Preset 21 to turn on the manual mode. The module will be switched into color or mono mode. And lights can be controlled via the commands of presets 30~33.
For White Light version: Call Preset 21 to turn on the manual mode. The module will be switched into color or mono mode. And lights can be controlled via the commands of presets 72 and 73.
[Note] All lights are suggested to be turned off to protect the camera when temperature is
above 50.
Image Freeze
Call Preset 28 to turn on/off the function. When it is on, during a regular preset call (see following picture), the video will be frozen at point A till Point B. At Point B, the video will be displayed normally.
18
Operation
Fig.12: Image Freeze
Soft Address
The camera address can be changed via presets 62 and 63. The new address will take effect after the camera is rebooted.
Digital Image Stabilization (DIS)
The function is off as default. It can be turned on/off by calling preset 29.
It is used when the camera is used in a vibration environment, to compensate the vibration in video.
Frame Scan
Call preset 49 and the PTZ will do frame scan. When the left and right limits are not programmed , the function cannot be activated.
19
Operation
Table 3 Trouble Shooting
Problems
Possible Causes
Solutions
No action when powered on
Power supply failure
Replace power supply
Wrong connection of the power
Check & reconnect the cables
Abnormal self-test motor noise
with
Mechanical failure
Repair
Camera inclined
Reinstall the camera
Inadequate power supply
Replace the power supply
Normal self-test but no images
Video signal failure
Reinstall camera
Wrong connection of the video
Check & reconnect the cables
Camera damaged
Replace the camera
Normal self-test but out of control
Wrong connection of RS485 cable
Check cable
and
reconnect
the
Wrong camera address set
Check and reset the Switches
Vague image Bad connection of the video
Check cables
and
reconnect
the
Inadequate power supply
Replace the power supply
PTZ camera out of control Self test error
Restart the camera
Wrong connection of RS485 cable
Check cables
and
reconnect
the
Loading...