XtendLan DVR-870PUE User Manual

H.264 NETWORK Embedded DVR

User

User Manual

Manual

V1. 1 -4/8CH New Interface

Thank

you

for

Thank

Thank you that

you

that

you

that

that you

you can

ground ,benefit for machine cooling ， Be sure not to block its air vent. ， keep away from heat sources and high temperaturea environment 。

shaking place （ such as the back of car 、 motor above 、 high and rough luggage-rake ） .

prevent DVR(include camera and other parts) touch water and wet, the machine don’t have waterproof.

or adjust any parts,if need maintenance , please contact the distributer or customer service .

the DVR work requirement , to meet a long time largeamount of data read and write requests , please purchase from the formal channels to ensure the hard disk quality .

purchase

you

for

purchase

you for

for purchase

purchase our

can

use

can

use

can use

use the

Attentions:

◆ T he DVR should be installed in a well-ventilated place ， keep suitable space from

◆ Please keep the level installation of this product.should be avoid install at violently

◆ F or avoid short circuit cause fire or other damage ， when wash the car please

◆ The equipment consists of Precision Parts , please d o not try to disassemble

◆ Please select the hard disk which commended by the manufacturers ,suit

our

our product

the

device

the

device

the device

device correctly

product

.

product

.

product .

. Please

correctly

correctly and

Please

Please read and

safely

and

safely

and safely

safely .

read

read this

.

this

user

this

user

this user

user manual

manual

carefully

manual

carefully

manual carefully

carefully to

to

ensure

to

ensure

to ensure

ensure

◆ This product can

or multi-layer laminated on the product .

Disclaimer:

T he Company is do the best to make the contect correct and complete during the preparation of this manual , if has any errors or omissions without any liability , the company reserves the right to change any hardware and software mentioned inthis manual at any time , and without explain beforehand. Thank you for choosing our products, please read this manual carefully before use . Due to not according to the specified operating losses, company will not assume any financial liability and legal responsibility .

’ t

bear heavy weight,please do not place heavy object

CONTENT

1. Product Introduction ................................................................................................... 2

1.1 Summary ................................................................................................................ 2

1.2Main functions ………………………………………………………………… . 4

1.3 Front panel buttons description

1.4 Rear panel diagram …………………………………………………………… 6

1.5 R emote control ………………………………………………………………… 7

2. Basic function operation ............................................................................................ 2

2.1 On/off Switching navigation

2.2 Login …………………………………………………………………………… .8

2.3 Main menu setup guide ....................................................................................... 2

2.4 Configuration management ……………………………………………… ....10

2.4.1 Basic configuration ...................................................................................... 2

2.4.2 Live configuration ........................................................................................ 2

2.4.3 Record configuration ................................................................................... 2

2.4.4 Schedule configuration

2.4.5 Alarm configuration ………………………………………………… ..... 16

2.4.6 Network configuration ................................................................................. 2

2.4.7 User management …………………………………………………… ...20

2.4.8

P.T.Z

configuration

2.4.9 A dvance configuration ................................................................................ 2

2.5 Data retrieval ........................................................................................................ 2

2.5.1 Time search .................................................................................................. 2

2.5.2 Event search

2.6 Backup ................................................................................................................... 2

2.7 check information ................................................................................................ 2

2.8 Disk management ................................................................................................ 2

2.9 Upgrade

2.10 Logoff ................................................................................................................... 2

2.11 System shut down ............................................................................................. 2

.................................................................................................................

................................................................................................

.........................................................................

................................................................................

...............................................................................

.......................................................................................

2

3

1. Product Introduction

1.1 Summary

This device is a digital monitoring and recording product specially designed for the

security field. It adopts standalone processor and standalone Linux operati ng system.

The device combines with the latest technologies in the IT field, such as video and audio compression/decompression, large capacity HDD record, TCP/IP network etc. . The code is embedded in the FLASH chip , which makes the system running more steadily. This device has both features of digital video and audio recording(DVR) and digital video and audio server(DVS). It can not only work locally and independently but also compose of a powerful security monitoring net with networking. With the use of professional network video surveillance platform (network) software, it can fully reflect its strong networking and remote monitoring capability.

It can be used for the security protection in the fields of banking, telecommunications, electronic power, justice, traffic, residential, factory, warehouse, water conservancy facilities and other areas and departments.

1.2

Main

1.2

1.2 Main

�

� Real

It is with analogue video output port, VGA port. It can realize the monitoring function through the monitor or display. It supports simultaneous TV and VGA output .

�

� S

It adopts special format to save data which cannot be tampered with and will be secured

�

� Compression

It supports multi-channel audio and video signal. Each channel of audio and video signal is compressed in real time by independent hardware. The sound and image keep stabilized synchronization.

�

� Backup

The client computer can download and backup the files on the hard disk via the internet

Functions

Main

Functions

Main Functions

Functions

Real

-

time

Real

S

torage

S

torage

S torage

torage Function

Compression

Compression Method

Backup

Backup Function

It backups through USB port(such as common U disk, mobile hard disk etc.)

Monitoring

-

time

Monitoring

-

time

time Monitoring

Monitoring

Function

Method

Function

�

Video

Play

back

�

Video

�

� Video

Each channel can realize independent and real - time recording, while retrieval , reverse play , network monitoring, video search and download etc. can realize simultaneously .Multiple playback modes: slow forward , fast forward , reverse play and frame-by-frame play. When playing back the video , the exact time of the event can be displayed.

�

� Network

search and playback , and remote PTZ control

�

� Communication

With RS485 port and PTZ control. With standard Ethernet port, realizing network remote control function

�

� PTZ

Support the PTZ decorder which communicates through RS485 .

Play

Video Play

Play back

Network

Network Operation

T hrough the internet , y ou can realize remote and real - time monitoring, remote video

Communication

Communication Port

PTZ

Control

PTZ

Control

PTZ Control

Control

Function

back

Function

back Function

Function

Operation

Operation Function

Port

Function

.

4

Can expand multiple decoding protocol s, facilitating the realization of PTZ and dome camera control.

�

Intelligent

�

Intelligent

�

� Intelligent

Intelligent Operation

Mouse operation function.For the same settings on the menu, you can copy and paste quickly. check equipment and accessories . When you receive the product , please check the accessories are complete or not . DVR accessories generally include: mouse, power lines and data lines .

1.3

F

ront

1.3

F

ront

1.3

1.3 F

F ront

ront panel

Statement:

Statement: the front panel interface, button layout and type, real product shall prevail.

The front panel buttons Description

Operation

panel

panel buttons

buttons

buttons description

description

:

Buttons

Buttons on

1 ） IR

2 ） LED

3 ） Playback

• : Increase reverse playback speed 1X, 2X, 4X

•

frame-by-frame

• : Press to start playback

• : Press to slow playback speed by 1/2, 1/4, 1/8

• : Press to increase forward playback speed 1X, 2X, 4X

4 ） MENU/

5 ） Navigation:

• : In menus, press to confirm selections; in PTZ mode, press to change the

navigation buttons to control the connected PTZ camera (not included)

• : Press to move cursor up; in PTZ mode, press to pan camera up

• : Press to move cursor down; in PTZ mode, press to pan camera down

• : Press to move cursor left; in PTZ mode, press to pan camera left

• : Press to move cursor right; in PTZ mode, press to pan camera right

6 ） USB upgrades connect a USB mouse to the bottom port.

on

Front

on

on Front

IR

Sensor

IR

Sensor

IR Sensor

Sensor （ Red

LED

Indicators

LED

Indicators

LED Indicators

Indicators : Shows status of alarm, rec,power,link,HDD .

Playback

Playback : D uring playback, press the following:

:

Press to freeze playback to one frame, then press again to advance

MENU/

OK

MENU/

OK

MENU/ OK

OK : Press to open/close the main menu.or confirm.

Navigation:

Navigation: Press the Navigation buttons to perform the following:

USB

USB : Connect a USB flash drive to the top port for data backup and firmware

Panel

Front

Panel

Front Panel

Panel

Red

Color

Red

Color

Red Color

Color ） : IR receiver for the remote control.

5

1.4

Rear

panel

1.4

Rear

1.4

1.4 Rear

Rear panel

Statement:

Statement: the rear panel interface, button layout and type, real product shall

prevail. ， below rear panel picture may be different with the actual panel

diagram

panel

diagram

panel diagram

diagram

.

Connectors

Connectors on

on

Rear

on

Rear

on Rear

Rear Panel

Panel

Panel ：

6

1.5

R

1.5

1.5 R

click of the mouse.

emote

R

emote

R emote

emote control

In device operation, the enter key on remote control has the same function as left

The remote control is the secondary input device

For navigating the system’s interface.

To

use the remote control:

.

STANDBY

.

STANDBY

1

.

STANDBY

STANDBY : When DVR on, constantly press the

RED button on the top for 3 seconds, the DVR will be in standby status.Under standby mode, press one time for immediate start.

LOGIN/LOCK

2. LOGIN/LOCK

LOGIN/LOCK : If "Security" has been enabled in the

Setup menu, press to open the user password login

screen.

Number/Channel

3. Number/Channel

Number/Channel buttons

press buttons 0~9 to enter values; during live

viewing, press to view channels in full-screen.

4. : Press to switch between quad and

split-screen displays.

MENU

5. MENU

MENU : Opens the main menu. PTZ

PTZ

6. PTZ

PTZ : Press to open the PTZ control window. EXIT

EXIT

7. EXIT

EXIT : Close menu windows. Navigation/OK

Navigation/OK

8. Navigation/OK

Navigation/OK :

• : Move cursor in menus up;

• : Move cursor in menus right;

• : Move cursor in menus left;

• : Move cursor in menus down;

OK

• OK

OK : In menus, press to confirm selections; during

playback and preview, press to view system information

+

9. +

+ /

RECORD

10. RECORD

RECORD : Press to start manual recording.

STOP

11.

STOP

STOP : Press to stop manual recording.

EXTRA

12. EXTRA

EXTRA : For the future use. Playback

Playback

13. Playback

Playback controls

• : Increase reverse playback speed 2X, 4X, 8X

• : Press to start playback

• : Press to increase forward playback speed 2X,

4X, 8X

• : Press to slow playback speed by 1/2, 1/4, 1/8

• : Press to freeze playback to one frame,

then press again to advance frame-by-frame

control

buttons

buttons : While in menus,

-

- :

In menus, press to adjust values.

controls

controls :

TIP

TIP : When using the remote

control to enter password and camera titles, select the field using the navigation buttons, press ENTER, and then press the number buttons.

Check

whether

Check

whether

Check

Check whether

whether there

For the convenience of readers read and quick queries , the following sections with a example of 4 - channel digital hard disk recorders to intro du cethe detail s , and pictures are base on this model, other model’s operation interface are the same except channel and frame rate, Corresponding parameter to the same settings , individual parameters can be directly and so on .

there

there is

is

fluorescent

is

fluorescent

is fluorescent

fluorescent light

7

light

being

light

being

light being

being used

used

used in

in

the

in

the

in the

the nearby

nearby

2.

Basic

2.

Basic

2.

2. Basic

Basic function

2.1

On/off

2.1

On/off

2.1

2.1 On/off

On/off Switching

2.1.1

2.1.1 S

Before start ， Please ensure all parts connected well ！ Power on Equipment start ， POWER indicator light is red.

2.1.2

2.1.2 Power

User can power off the device by using remote controller 、 keyboard and mouse.

2.1.3

2.1.3 By

P ress Power button, the Shut down window will appear, click OK, the unit will power

off after a while.

2.1.4

2.1.4 D

Step1: enter into Menu, then select “ System Shut Down ” icon, the Shut down window

will appear

Step2: click OK, the unit will power off after a while. Step3: disconnect the power

2.2

2.2 Login

Equipment start , 【 POWER 】 indicator light bright . initial password is blank . After

equipment start press 【 MENU 】 key on panel or press right key on mouse interface as below :

Switching

Switching navigation

S

tart

S

tart

S tart

tart

Power

off

Power

off

Power off

off

By

remote

By

remote

By remote

remote controller:

D

isconnect

D

isconnect

D isconnect

isconnect the

Login

controller:

the

the power

function

function operation

navigation

power

b

y

power

power b

keyboard

b

y

keyboard

b y

y keyboard

keyboard and

operation

and

mouse

and

mouse

and mouse

mouse :

,

trun to login

After Input matching user name and password ,you can enter system to setup and operation .

Live preview interface:

P ic 2 -1 User login

8

Icon

Sign

Sign description

description

�

Live

playback

�

Live

playback

�

� Live

Live playback

playback

Click Playbutton to playback the record enter fast record playback : as lelow

picture:User can do concrete operation by click the buttons on screen .

2.3

Main

2.3

Main

2.3

2.3 Main

Main menu

Menu

Menu bar:

will display on the bottom of the screen, refer to p ic2-2

Click the icon near Screen mode,appear channel choose frame as below

recording

menu

menu setup

bar:

bar: Click right mouse or press ESC button on the front panel, the control bar

setup

setup guide

Manual record

guide

P ic 2-2 Menu bar

M otion detectio n stat e

Alarm state

Timing recording stat e

9

P ic 2 - 3 Channel choose

user could choose 1 channel from 1-4 to show live video.click to save .

Click function menu ， will show dialogue frame as Pic 2 - 4;

C lick “ configuration management ” ， display syswindows as pic 2 - 5:

Press MENU button on the front panel or the same button on remote control ,

also cuold display the same window .

2.4

Configuration

2.4

Configuration

2.4

2.4 Configuration

Configuration management

Configuration Management contains nine sub- menu: basic configuration on-site configuration , video configuration , recording plan , alarm configuration , network configuration, user management, PTZ configuration and advanced configuration .

Pic 2 - 4 M ian function

Pic 2-5 Configuration management ”

management

10

,

2.4.1

Basic

2.4.1

2.4.1 Basic

Click “ Basic configuration ” ， show window as pic2-6, The basic configuration contains two sub- menu: system date and time

1)

system

1)

system

1)

1) system

system

configuration

Basic

configuration

Basic configuration

configuration

I n this interface user can setup the device name, device ID, video format, Video Output and language, Screensaver and so on. The definitions for every parameters display as below:

Device

name:

Device

name:

Device

Device name:

device remotely.

to that of camera.

can do corresponding operations with the relevant right in system configuration.

VGA1024*768, VGA1280*1024 and CVBS

English,Japanese, German ,Russian,French,Portuguese,Turkish,spanish,Italian,Polish, Hungarian,Slovak,Vietnamese,greek

and video output, the device will restart .

2

)

Time

2

)

Time

2

2 )

) Time

Time &

name: It may display on the client end or CMS that help user to recognize the

Device

number:

Device

number:

Device

Device number:

number: Corresponding with the remote control number

Video

format:

Video

format:

Video

Video format:

format: two modes:

Password

Password check:

Show

Show system

Video

Video output:

Language

Language:setup the menu language:Simplified Chinese , Traditional Chinese ,

Click the "Default" button, the system restore the default things

C lick the "Apply" button will save the above settings;

C lick the " E xit"button to exit the current interface , Tip to change the menu language

check:

check: Enable this option. user needs to input user name and password

system

time

system

time

system time

time ： choose display time in live or not

output:

output: the resolution of live display interface, range from: VGA800*600,

&

date

&

date

& date

date

Pic 2-6 System

PAL

and NTSC. User can select the video format according

;

Pic 2-7 Time & date

11

S et the date format , time format time zone at the date and time " interface,; check the " Keep synchronized with network time server " to update the network time server . alsomanually adjust the system time 。

Note:

Note: The system default is GMT time zone , please choose GMT +8 in the time

zone drop-down frame

Click the " Default" button, the system restore the default settings;

C lick the "Apply" button will save the above settings

C lick the " E xit " button to exit the current interface .

2.4.2

Live

2.4.2

2.4.2 Live

2.4.2.1

2.4.2.1 Live

different character format to input .

configuration

Live

configuration

Live configuration

configuration

Live

Click “ Live

Live configuration

Live configuration includes two submenus : live and mask

Live

Live configuration

Note:

Note: Click Camera Name to see a soft keyboard. User can choose

T

ick off camera name and click “ S etting”button to display a window as below ：

.

configuration

configuration ” ， enter window as pic2-8

configuration

Pic 2- 8 Live configuration

.

;

You

can

Pic 2- 9 L ive-color adjustment

I n this interface, user can adjust brightness, hue, saturation and contrast in live; click

“

D efault ” button to resort default setting, click “ OK”button to save the setting. user can setup all channels with same parameters, please tick off “ all ” and then do relevant setup.

2.4.2.2

Mask

2.4.2.2

Mask

2.4.2.2

2.4.2.2 Mask

Mask

P rivate mask . User can setup private mask area on the live image picture ，

12

Setup

mask

Setup

Setup mask

drag mouse to set mask area, refer to below picture. Click Apply button to save the setting. ；

Delete

mask

Delete

mask

Delete

Delete mask

mask area:

area, click Apply button to save the setting.

2.4.3

Record

2.4.3

Record

2.4.3

2.4.3 Record

Record configuration

Click “ Record

Record configuration includes four sub menus: start , record bit rate, Character

overlay.recycle record .

area:

mask

area:

mask area:

area: click Setting button, enter into live image to press left mouse and

area:

area: select a certain mask area, click left mouse to delete that mask

configuration

Record

configuration

Record

configuration

Record configuration

configuration ” ， enter window as pic2-1 1 ：

Pic 2-10 M ask

Live image mask area

13

2.4.3.1

Start

2.4.3.1

Start

2.4.3.1

2.4.3.1 Start

Start

T

ick off record channel , channel audio

U ser can setup all channels with same parameters, tick off “ A ll ”,then to do relevant

setup.

C lick “ D efault”button to resort default setting; click “ A pply ” button to save the setting; click “ exit”button to exit current interface Video parameters instruction

Parameter

Parameter Meaning

start Every channel record switch audio Start use the channel record audio

2.4.3.2

R

ecord

bit

2.4.3.2

R

2.4.3.2

2.4.3.2 R

setup.

click “ E xit ” button to exit current interface.

ecord

R ecord

ecord bit

S etup rate, resolution, quality, encode and max bit stream

U ser can setup all channels with same parameters, tick off“All ” , then to do relevant

C lick “ D efault”button to resort default setting; click “ A pply ” button to save the setting;

bit

bit rate

rate

Pic 2-11 Start

Pic 2- 12 R ecord bit rate

.

Meaning

.

14

2.4.3.3

Record

2.4.3.3

Record

2.4.3.3

2.4.3.3 Record

Record stream

stream

stream introduce

introduce

Parameter

Parameter Meaning

F ps Range from 1-30 （ NTSC ） 1-25(PAL)

Resolution Support D1 、 CIF

Quality

Coding Support CBRand VBR

Max stream

Stamp

：

Stamp

：

Stamp

Stamp ：

： User can overlap the channel name and time stamp on video .

T

ick off camera name, time stamp; click Setting button, and then user can use cursor to drag the camera name and time stamp in random positions. Please refer to below Figures U ser can also setup all channels with same parameters.

C lick “ D efault ” button to resort default setting; click “ A pply”button to save the setting;

click “ E xit ” button to exit current interface

2.4.3.4

Recycle

2.4.3.4

Recycle

2.4.3.4

2.4.3.4 Recycle

Recycle record

T

ick off recycle record to enable the recycle record function. It will cover the earlier recorded files and keep recoding when HDD is full; if disenabled, it will stop recording when HDD is full. Note: general the image quality, frame rate and resolution parameters setting higher,the more take up disk space

C lick “ D efault”button to resort default setting; click “ A pply ” button to save the setting;

click “ E xit ” button toexit current interface.

record

Meaning

The higher the value is, the clearer the Recorded image is. Six options ： lowest , lower , low, medium, higher and highest.

Select range ： 16Kb 、 32Kb 、 64 Kb 、 128 Kb 、 256 Kb 、 512Kb 、 640Kb 、 768Kb 1024Kb 、 1536Kb 、 2048Kb

Pic 2-13 Character overlay

.

、

2.4.4

Schedule

2.4.4

Schedule

2.4.4

2.4.4 Schedule

Schedule configuration

Schedule configuration includes two sub menus: schedule and motion .

2.4.4.1

Schedule

2.4.4.1

Schedule

2.4.4.1

2.4.4.1 Schedule

Schedule

configuration

15

The volume means the seven days of a week from Monday to Sunday; the row means 24 hours of a day. Click the grid to do relevant setup. Blue means checked area, gray means unchecked area.

Copy

Copy ： User can apply the schedule setting of certain channel to other or all channels.

Just only select channel and click “ Copy ” button

C lick “ D efault”button to resort default setting; click “ A pply ” button to save the setting; click “ E xit ” button to exit current interface.

2.4.4.2

Motion

2.4.4.2

Motion

2.4.4.2

2.4.4.2 Motion

Motion

T he setup steps of motion are familiar with schedule

Note:

Note: the default schedule of motion detection is full-selected, that is, the color of

schedule setting interface is blue

2.4.5

Alarm

2.4.5

2.4.5 Alarm

out

.

2.4.5.1

2.4.5.1 Sensor

configuration

Alarm

configuration

Alarm configuration

configuration

Alarm configuration includes five sub menus: sensor, motion, video loss and alarm

Sensor

The h ardware does not support

Pic 2-14 S chedule

Pic 2-15 Motion

.

2.4.5.2

Motion

2.4.5.2

Motion

2.4.5.2

2.4.5.2 Motion

Motion

Motion includes one sub menus: motion

1>

Motion

1>

Motion

1>

1> Motion

Motion

16

Click start motion alarm and set alarm hold time ， It refers to after close motion alarm it delay to the preset setting time . Click alarm "Settings" button,show below window ：

Pic 2-16 Motion

Alarm configuration, trigger video alarm handling, linkage alarm handling

Pic 2-17 Alarm handling

and sensor alarm handling trigger settings is same.

C lick on "Regional Settings" button at Motion detection interface, trun to the

following window ;

Pic 2-18 Motion detection - Regional Settings

At area Set ting interface, users can drag the slider to adjust the sensitivity value ( 1-5), the default value is 4 , 1-5 sensitivity progressive increase . Sensitivity influenced by the color

of time ( day or night), the user s should ad just according to actual situation . click icon ，

set All locales for the detection region ； click icon ， will clear setting detection region

click icon ， save setting ； click button,exit from current interface.

U ser can setup all channels with same parameters, please tick off “ all ” , and then to do

17

；

relevant setup .

C lick “ D efault”button to resort default setting; C lick “ A pply ” button to save the setting; click “ E xit ” button to exit current interface.

2.4.5.3

Video

2.4.5.3

2.4.5.3 Video

loss

Video

Video loss

loss

Click “ alarm handling ” button ， turn to window as below ：

T he setup steps of video loss trigger are familiar with alarm handling

U ser can also setup all channels with same parameters ，。 click “ A pply”button to save the setting; click“E xit”button to exit current interface.

C lick “ D efault”button to resort default setting ； Disconnected from the network: when the network connection is disconnected, the system will automatically sent E-mail to the user specified mailbox about the network disconnected .

2.4.5.3

Alarm

Alarm out

out

configuration

2.4.5.3

2.4.5.3 Alarm

The h ardware does not support

2.4.6

Network

2.4.6

Network

2.4.6

2.4.6 Network

Network configuration

Network configuration includes four submenus: network, sub stream, Email and other

settings

.

Pic 2-19 Video loss

Pic 2-20 Video loss - alarm handling

.

2.4.6.1

Network

2.4.6.1

Network

2.4.6.1

2.4.6.1 Network

Network

18

HTTP

port

HTTP

port

HTTP

HTTP port

number when typing IP address in IE address blank.IE set HTTP port to 82, IP address: http://192.168.0.25,user needs to input that address: http://192.168.0.25:82 into IE browser .

IP address automatically", the device will distribute IP address, subnet mask, and gateway IP and DNS server.

user name and password; click TEST button to test the effectiveness of the relevant information.

2.4.6.2

2.4.6.2 Network

port ： the default value is 80. If the value changed, user needs to add the port

Server

port

Server

port

Server

Server port

port : data and image communication port NO. After selecting the "Obtain an

E nable PPPoE to directly connect the DVR to internet via ADSL and then input the

C lick “ D efault ” button to resort default setting ； click “ A pply”button to save the setting; C lick

“

E xit”button to exit current interface

Network

Network Sub

Pic 2-21 Network configuration

Sub

stream

Sub

stream

Sub stream

stream

.

select fps, resolution, quality. ， user can also setup all channels with same parameters click “ A pply ” button to save the setting; click “ E xit ” button to exit current interface. network configuration-network

Parameter

Parameter Meaning FPS

FPS

FPS Range from: 1-25 Resolution

Resolution

Resolution Support CIF Quality

Quality

Quality The higher the value is, the clearer the record image. Six

Pic 2-22 Network Sub strea

.

Meaning

options: lowest, lower, low, medium, higher and highest.

19

.

2.4.6.3

Email

2.4.6.3

Email

2.4.6.3

2.4.6.3 Email

Email

SMTP

Server/Port:

SMTP

Server/Port:

SMTP

SMTP Server/Port:

Server/Port: the name and port number of SMTP server

Send

address/password:

Send

address/password:

Send

Send address/password:

address/password: sender’s email address/password .

Receive

address:

Receive

address:

Receive

Receive address:

address: receiver’s email address 。 Here user can add at least three mail

addresses

Click

T

est button to test the validity of the mailbox .

C lick“D efault ” button to resort default setting ； click“A pply ” button to save the setting;

click “ E xit ” button to exit current interface.

2.4.6.4

Other

2.4.6.4

2.4.6.4 Other

Enable DDNS server: user needs to input user name ， name of the registered website, click TEST to test the effectiveness of the relevant information. click “ default ” button to resort default setting; click “ apply”button to save the setting; click “ exit ” button to exit current interface.

Note

Note : the user select a domain name is bound by the Domain Name Service for DVR

you must first landing the website of the ISP registered user name and password,and then apply for a domain name for the server online . After the application is successful , the user could enter the domain name to access the server in IE side .

settings

Other

settings

Other settings

settings

Pic 2-23 Email

Pic 2-24 Other settings

.

，

， password and host domain

,

2.4.7

User

2.4.7

User

2.4.7

2.4.7 User

User management

management

20

Enter User management , as below pic ：

C licking Add button, a dialog box will pop-up as below ：

Pic 2-25 User management

Pic 2- 26 General

1

General: Input user name, password; select user type, input the MAC address of the PC; click OK button, this user will be added into the user list box; click Exit button to exit the current interface .

2

Authority:

Pic 2-27 Authority:

In the authority interface, assign the definite operation right for that user

.

I n the user management interface, click Setup button to modify user name, user type

and binding PC MAC address.

S elect the user that user wants to delete in the user list box and then click Delete button to delete this user. click Change password button to modify the password and then click Exit button to exit the current interface.

21

2.4.8

P.T.Z

2.4.8

P.T.Z

2.4.8.1

2.4.8.1 serial

configuration

P.T.Z

configuration

P.T.Z

configuration

configuration includes two submenus: serial port and advance

serial

port

serial

port

serial port

port

Click “ Start ” ， base on

U ser can setup all channels with same serial port parameters, please tick off “ A ll ”,and then to do relevant setup. click “ D efault ” button to resort default setting; click “ A pply ” button to save the setting; click “ E xit ” button to exit current interface

Definitions

Definitions and

Parameter

Parameter Meaning

Address The address of the PTZ device Baud rate Baud rate of the PTZ device. Range form: 110, 300, 600, 1200,

Protocol Communication protocol of the PTZ device. Range from:,

2.4.8.2

2.4.8.2 Advance

and

descriptions

and

descriptions

and descriptions

descriptions of

Meaning

2400, 4800, 9600, 19200, 3 84 00, 57600, 115200, 230400, 460800, 921600.

PELCOP , PELCOP1, PELCOP5, PELCOD, PELCOD1, PHILIPS, SAMSUNG SHARP ,SONY , SAMSUNG, PANASMIC , Control , etc …

Advance

Advance configuration

configuration

Pic 2-28 S erial port

P.T.Z

support Protocol to set Address , Baud rate ,and Protocol 。

of

serial

of

of serial

port:

serial

port:

serial port:

port:

HY,

Pic 2-29 Advance

22

I n the Advance interface, after clicking preset “ Setting”button, a dialog box will

pop-up as below ：

Pic 2-30 Preset point setting

I n the preset set interface, click Setting button to see a window as below ：

Pic 2-31 P reset set ting

U ser can control the

right and stop rotating ； can adjust the rotation speed of the PTZ , focus , focus and aperture

choose preset arrange NO. Click Save button to save the settings ， click icon to hide the

tool bar, right-key can remerge it ； click icon to exit the current interface

I n the preset interface, click OK button to save the setting; click Exit button to exit

current interface. I

n the Advance interface, click cruise “ Setting”button, a dialog box will pop-up as below ：

P.T.Z

up, up left, down, right down, left , left down, right and up

；

C lick Add button to add cruise line （ max 32 cruise line can be added ）； select a cruise

line and click Setup button, to see a window as below ：

Pic 2-32 Advance - cruise “ Setting ”

23

C lick Add icon ， to set the speed and time of preset point; select a preset point and

click Delete icon to delete that preset poin ； click Modify icon ， to modify the setting of a preset point ； User can click those icons to adjust the position of preset point.top 、 up 、 down and bottom 。 Click Preview button to preview the cruise line and then click

OK button to save the setting. Next, click Exit button to exit current interface

S elect a preset point in the cruise line list box and click Delete button to delete that cruise line; click Clear all button to clear all cruise line from the list box; click OK button to save the setting; click Exit button to exit current interface.

I n the Advance interface, click track “ Setting ” button to pop up a dialog box as below ：

Pic 2-33 C ruise set-preset point setting

U ser can control the dome rotates up, up left, down, right down, left, left down, right

Pic 2-34

and up right and stop rotating . adjust the rotate speed and the value of zoom, focus and iris of the dome ； click Start Record button to record the move track of PTZ and click this button again can stop record ； click Start track button to play recorded track and click this button again can stop play . The user can drag the slider to adjust the rate of

C lick icon to hide the tool bar, right-key can remerge it;click icon to exit the

current interface.

I n the Advance interface, click “ D efault”button to resort default setting; click “ A pply ”

button to save the setting; click“E xit”button to exit current interface.

T

rack setting

24

P.T.Z

movement .

2.4.9

A

dvance

2.4.9

A

dvance

2.4.9

2.4.9 A

A dvance

dvance configuration

Advanced settings include three sub-menu: factory settings, andimport / export and

exit .

1. Factory settings: all settings back to factory settings

2. Import/Export: Users can export data files to be backed up onremovable storage

devices, you can also import the specified data file from a removable storage device to a

DVR.

3. Exit: exit current interface

configuration

Pic 2-35 A dvance configuration

25

Returned to the main menu , enter the data retrieval interface .

2.5

D

ata

2.5

2.5 D

retrieval

D

ata

retrieval

D ata

ata retrieval

retrieval

Search configuration includes two submenus: Time Search, Event Search,

2.5.1

Time

2.5.1

2.5.1 Time

Step1 ： enter into Search configuration � Time Search; refer to below pic ：

Step 2 ： Select the channel , the calendar date , the start time and end time

Step 3 ： click “ Play ” button, Playback will start from the set time bucket ; click the

corresponding button on the screen to start concrete operations .

search

Time

search

Time search

search

Pic 2-36 Time search

Pic 2-37 Playback buttons

2.5.2

Event

2.5.2

2.5.2 Event

Step1: ： enter into Search configuration � event search; refer to below pic .

search

Event

search

Event search

search

26

Step2 ： After clicking Search button, the searched event information will displayed in the

event list box , double check a certain record file to playback.

Step 3 ： User can select date, channel. Tick off Motion, Sensor or All accordingly to

search .

2.6

Backup

2.6

Backup

2.6

2.6 Backup

Backup

This unit supports backup by USB device ， User also can make backup by IE browser

via internet

Step1: enter into backup configuration interface , as below pic ：

Pic 2-38 Event search

Step2: set the start & end time, select channels and click Search button to display the

searched data in the data backup list box .

Step3: checked a data file or tick off “ All ” to select all data files, click Backup button, 。 Step4: in the backup information interface, user can check the relevant information of

backup files, storage type, save file type, etc. click Start button to starting backup.

Pic 2-39 Data backup

27

2.7

Check

2.7

Check

2.7

2.7 Check

Check information

Through this option, the user can check system information , system journal , network

information

System

System Information

E nter menu � view information � system information ， in the interface user can view

the equipment and version information and relevant information

Log

information

Log

information

Log

Log information

information :

E nter menu � View system information � Log information ， in the interface users can

set the start & end time of log you want to view, select the type of log you want to view and click the search button , search ed the log information will be displayed in the log list box .

Note: Users can export data files to be backed up on removable storage devices .

Network

Network information

E nter menu � view information � Network c onfiguration ， in the interface ， Users

can view the relevant parameters of the network information .

2.8

Disk

2.8

Disk

2.8

2.8 Disk

Disk management

E nter menu�Disk management ， In the interface , the user can view disk storage state,

also can choose to format ting the hard disk

P lease format the hard disk before record , Specific operation as below ： Step1: enter into disk management interface ， The system will pop up the Disk

Management window .

Step 2:select a hard disk and click Format button to star format. ； set the property of the

disk then click Apply button to save the setting

2.9

Upgrade

2.9

Upgrade

2.9

2.9 Upgrade

Upgrade

mianboard, can get upgraded software from the buyers,to upgrade the system .

the USB storage device and then connect to the USB port. Enter Menu Upgrade ， refresh list the upgrade software name is displayed in the upgrade list box, select that software and click Upgrade button to start upgrading . System will automatically restart on the upgrade process Please wait for a while when the system is rebooted. Please don’t cut off power during upgrading 。 This system supports the upgrade of the USB device but it must be compatible with the USB device , need to reboot the system after the upgrade completed,to take effect.

Note:

devices are not compatible

information

Information

information

information :

Note:

Note: all recorded files in the hard disk will be lost after formatted .

Once have the new version,the user can choose to upgrade the panel and the

Upgrade

Upgrade step

Note:

Note: If the upgraded software does not appeared in USB, usually the USB

:

management

.

step

step ： user needs to copy the upgrade software which get from vendor into

，

28

2.10

Logoff

2.10

Logoff

2.10

2.10 Logoff

Logoff

Enter Menu � Logoff user wants to log in again, click mian menu icon to enter into user name and password to re-login.

2.11

System

2.11

System

2.11

2.11 System

System shut

C lick “ system shut down ” icon , shut down system .

Logoff

Logoff ， Click Log off icon,The system will exit the current user login. If

shut

down

shut

down

shut down

down

29

XtendLan DVR-870PUE User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1. Product Introduction

1.1 Summary

navigation

Live preview interface:

Live playback

Pic 2-6 System

Pic 2-7 Time & date

2.4.2.2 Mask

area, click Apply button to save the setting.

Start

2.4.3.1 Start

ick off record channel , channel audio

Parameter

Meaning

Resolution Support D1 、 CIF

Quality

Coding Support CBRand VBR

Max stream

2.4.4.1 Schedule

2.4.4.2 Motion

2.4.5.1 Sensor

2.4.6.1 Network

Parameter

Pic 2-22 Network Sub strea

Meaning

2.4.6.3 Email

Pic 2-29 Advance

Pic 2-37 Playback buttons

2.6 Backup

2.9 Upgrade

2.10 Logoff