ENGLISH
SINGLE FAMILY VIDEO INTERCOM
DPC-432W Manual
Outdoor Camera (O utdoor Station)
Features:
-
Suitable for 4-wires Single Entry system, compatible with DPM-4xx serials of monitors
-
Call button with blue backlight nameplate , up to 4 Monitors directly
-
Flush mount, and easy to be installed in a 86x86 box
-
Capable of installing with Rainy Cover in flush or surface mount.
Parts and Functions:
6
SYSTEM
DPC-432W outdoor camera
7
1R 2W 3Y
4B
B
L
8
■
CAMERA ANGLE ADJUSTABLE
NAMEPLATE CALL BUTTON
■
INFRARED NIGHT VIEW FUNTION
■
David
David
Dimensions: 130(H)×98(W)×40(D)
1. Camera lens: To capture the video image of the visitor.
2. Microphone: To collect the voice of the visitor.
3. Night view LED: To enhance the brightness when the outside is dim.
4. Speaker: To send out the voice from the indoor.
5. Call button: To c all the indoor monitor.
6. Angle adjust: To adjust different angles of the camera lens.
7. Connection Port: To conect to the indoor monitor, C3-4P cable should be used.
(NOTE: 1R-power posivite, 2W-power negative, 3Y-video signal, 4B-audio and data)
8. Unlock Port LB: To connect to the electronic lock, C3-3P cable should be used.
3
Mount Instruction:
how to take off the mounting
bracket
Use a screwdriver to put up the cover
underside the call button(with nameplate); screw out the screw and take off
the bracket.
how to placed the nameplate
Turn around the cover, and take out the
nameplate salver; put the paper with
your own mane on the salver and insert
it back to the socket.
● Make a hole of 75X75X35mm on the wall, and fix the mounting bracket. If possible,
an existing 86x86 box can be used.
● Wire the cables, and test the single entry system until it works. Adjust the camera
angle if necessary.
● Fix body with bracket, then tight the screw firmly.
Precautions:
-
Do not install in a place where there would be a bright light behind a visitor (or where
there would be a bright background), or in a place where the camera lens would be
directly exposed to sunlight or a bright light. If light comes in on the unit 's screen, the
image looks white or silhouetted. But this is not a unit trouble.
-
Do not install the unit in places where High or extreme cold temperature, moisture or
humidity extremes, Constant vibration or impact, steam or smoke.
Specifications:
-
Power Supply: DC 10~12V (Powered by Monitors)
-
Power Consumption: 150mA in working state (not including the latch activating)
-
Video Output: 75 Ohm Impedance, 1Vp-p, CCIR standard (unless speci fied)
-
Camera: 76 degree, CCD or CMOS camera with IR-LED for night vision
-
Working temperature: -10 ~ 40 Centigrade
Electronic Latch connecting instructions
-
Mode 1: With Monitor’s JP-LK Jumper (Dry contact)
Extra power supply for latch must be
installed, and nearly all kinds of electronic
LB
port
1
2
3
POWER
SUPPLY
latch can be used. Incidentally, in this
mode, you can continue talking and
monitoring during unlock operation.
-
Mode 2: Without JP-LK Jumper (DC output)
LB port
1
2
Connect with 1R
Connect with 2W
rated voltage is DC 12V, less than 500mA
The Latch can directly connect with the Door
Station and use the power from monitor.
During unlock operation, the screen of indoor
monitor will close automatically. The Latch’s
consumption.
Note: Please use right and specific Latch.
Loading...