XtendLan DPA-D2-AKP User Manual

2 WIRE SYSTEM

Access keypad panel with scramble keypad

User Manual

RF CARD

•Pleasereadthismanualcarefullytoensuresafeandcorrectoperation.

•Keepthismanualwellforfuturereference.

1.Parts and Functions

7

8

3

9

2.Terminal Descriptions

1

2

5

4

6

SD Card Slot

[1] Front panel

[2] Touch sensitive digital
keypad

[3] LED1 indicator

[4] LED2 indicator

[5] LED3 indicator

[6] ID card window

[7] Mounting hook

[8] Connection port

[9] Screw hole

CN-LK

L2

L1

BUS

+12V
LK­LK+
NO
EB-

EB+

• SD Card Slot: To insert micro SD card.

• BUS: Connect to the bus line, non polarity.

• +12V: 12VDC power output.

• LK+: Common contact of the relay.

• LK-: Power ground.

• NO: Normally open contact of the relay.

• EB+: Exit button power(+) output.

• EB-: Exit button power(-) output.

-1-

3.Mounting

1 2

Use the screws to fix the mounting bracket to the wall.

Attach the panel to the mounting bracket. Use the screwdriver and the screw to fix the panel.

4.Electric Lock Connection

4.1 Internal Power Supply Mode

Connect the cable correctly.

43

Use the power of the system to supply for the electronic lock, so that the lock can be
connected to the access keypad panel directly, without an additional power supply for the
electronic lock. Note that the access keypad panel can only output 12Vdc power, therefore the
kind of lock is limited.

-2-

• The rated power of the lock must be less than 12Vdc 300mA when using internal power
supply mode.

• The GND must connect to the negative of the lock, and the COM connect to the positive .

• The default unlock time is 3s. If different unlocking time is needed to be configured,
change the Unlock Timing on access keypad panel.

A. Connection for Power-on-to-Unlock type:

-

+

12V 300mA

+12V
LK - (GND)
LK+(COM)
N.O.
EB+
EB -

Set Unlock Relay mode
to Normally Open(0)

B. Connection for Power-off-to-Unlock type:

-

+

12V 300mA

+12V
LK - (GND)
LK+(COM)
N.O.
EB+
EB -

Set Unlock Relay mode
to Normally Closed(1)

4.2 External Power Supply Mode

When the electronic lock is over 12 Vdc, external power supply for the lock is needed.

• The power supply for the lock must be less than 48Vdc 1.5A.

• The default unlock time is 3s. If different unlocking time is needed to be configured,
change the Unlock Timing on access keypad panel.

C. Connection for Power-to-Unlock type:

-

+

+

-

+12V
LK - (GND)
LK+(COM)
N.O.
EB+
EB -

Normally Open(0)

Note: Cut off this line when
using external power supply

-3-

Set Unlock Relay mode to

D. Connection for Power--off-to-Unlock type:

-

+

+

-

+12V
LK - (GND)
LK+(COM)
N.O.
EB+
EB -

Set Unlock Relay mode to
Normally Closed(1)

Note: Cut off this line when
using external power supply

5. Functions Setup

This section explains the settings of each parameter,please refer to the following table:

About the setting mode:

Input the master code to enter the setting mode, and input the corresponding setting code to perform the settings
for the function you want. After settings have been made, input the following setting codes to continue the setting
operation. Press "



" to exit the setting mode.

• The example is set
setting for detail information.

• Forbid sliding touch to the digital keypad, it may cause mistaken key, the correct operation is

using your nger to press the digital you desired.

• You should press“conrm”button after nish inputting the code number each time, otherwise,
the operation will be canceled automatically after 10s.

as cancel button and # as conrm button, please refer to */# function

5.1 Setting Items and Codes

Order Setting items Setting code Setting range Default value

1 Reset all settings 00

2 Set master code 01

3

Set digitron display

mode(in standby mode)

02 Valid keys:0 ~ 2 0

-

1 ~ 12 digits

Valid keys:0 ~ 9

1,2,3,4

1234

-4-

4 Set unlock time 03 1 to 99 seconds 1 seconds

5 Set unlock mode 04 0:opened/1:closed opened

6

7 Reset code settings 06

8

9 Tone select 08 0:Disable/1:Enable 1

10

11 Keyboard mode 10 0:standard / 1:scramble 1

12 Unlock work mode 11 Valid keys:0~3 0

13

14

15 Device Address 14 Valid keys:0~3 0

16 RLC Control 15 Valid keys:0~4 0

17

Set touch key prompt

mode

&# function settings 07 0:Normal/1:Reverse Normal

Interference resistant

grade settings

Backup(master / user

card / password / tone)

Update(master / user

card / password / tone)

Temporary(single use

only) password for relay1

05

09 Valid keys:0 ~ 5 3

12

13

18 Valid keys: 0 - 9

0:ashing / 1: beep /

2:ashing + beep

-

-

-

1,2,3,4

1,2,3,4

1,2,3,4

2

-

18

19

20

21 Register [Manage card] 100

22 Add user card 101

23 Delete user card 102

24 Format user card 103

Temporary(single use

only) password for relay2

Set the code for user

group 1

Set the code for user

group 2

19 Valid keys: 0 - 9

20-59 Valid keys: 0 - 9

60-99 Valid keys: 0 - 9

-5-

-

-

-

-

-

-

-

1,2,3,4

1,2,3,4

1,2,3,4

1,2,3,4

5.2 LED Indicator Denitions

Indicator Status Description

LED1 Light on Release the rst/second lock

Light on Register [Add Manage card] / Add user card

LED2

LED3

Flash Register [Delete Manage card] / Delete user card

Double ash

Light on Setting code

Flash Setting value

Format or Conguration switching of ACC and ID card, it waits for

5.3 Digitron Display Prompt

Digitron display Prompt

OP1 Release the rst lock

OP2 Release the second lock

SUC Setting success

Err Password error / Non-access card

conrmation

Err

Err

Err

Err

1

2

3

4

Setting code input error

Setting value input error

Cards have reached the number of rated

Input rule error

-6-

Err

5

Wrong password 10 times in a row, is locked

Err

6

ACC The access control is congured for the ACC application

ID The access control is congured for the ID card unlock application

S-A Register [Add Manage card]

S-D Register [Delete Manage card]

ADD Add user card

DEL Delete user card

CLE Format user card

BC1 Backup [Manage card]

BC2 Backup user card

Swipe invalid user card(When unlocking need swipe valid user card and password )

BC3 Backup unlock password

BC4 Backup ringtones

UD1 Update [Manage card]

UD2 Update user card

UD3 Update unlock password

UD4 Update ringtones

-7-

5.4 Setting Steps

Input the master code.

(Default: [ ] +[#] )

1.Reset all settings

Input the setting code.

00+#

LED1 LED2 LED3

Beep+, Beep Beep+, Beep Beep+, Beep Beep+, Beep

(flash)(off)(off)

Inputting of code.

1234+# 4321+#

LED1 LED2 LED3

(off)(off)

(on)

Beep+

2.Set master code
(Default

Input the setting code.

1234)

01+#

LED1 LED2 LED3

(flash)(off)(off)

Inputting of new master code
(ex.: 4321)(1~12 digits)

LED1 LED2 LED3

(off)(off)

(on)

Beep+

LED1 LED2 LED3

3.Set digitron
display mode

Input the setting code.

02+#

LED1 LED2 LED3

(flash)(off)(off)

Inputting of value(ex.: 0)
range:0~2

0+# 09+#

LED1 LED2 LED3

(on)

(off)(off)

(on)(off)(off)

Beep+

Beep+, Beep

4.Set unlock time
(Default: 1s)

Input the setting code.

03+#

LED1 LED2 LED3

(flssh)(off)(off)

Inputting of value (ex.: 09)

range:01~99

LED1 LED2 LED3

(off)(off)

(on)

Beep+

-

When the “ cancel” key is pressed, the indicator will show its standby color,

*

the buzzer beeps, and the system exits the setting mode.

-

When there isn’t any operation within 10s, the indicator will show its standby color,

the buzzer beeps, and the system exits the setting mode.

- All settings will restore to their
default value.

- The master code is allowed 1~12
digits,the same code cannot be set
for both the user code and the
master code,it is recommended
that you modify the default master

- Digitron display mode:
0 : The scrolling display;
1 : All digitron display “-” sign;
2 : Only the upper left corner of the
digitron display “-” sign.

code.

-8-

LED1 LED2 LED3

(off)

(off)(off)

- The unlock time can be set on
access keypad panel, and the
valid value is the number you set
last time.

Beep, Beep+

Input the master code.

(Default: [ ] +[#])

LED1 LED2 LED3

(on)(off)(off)

Beep+, Beep

5.Set unlock mode

7.Reset code setting 8. &# function setting 6.Set touch key

prompt mode

Input the setting code.

04+# 05+#

LED1 LED2 LED3

(flash)(off)(off)

Beep+, Beep

Input the setting code.

LED1 LED2 LED3

(flash)(off)(off)

Beep+, Beep

Input the setting code.

06+#

LED1 LED2 LED3

(flash)(off)(off)

Beep+, Beep

0/1

Inputting of value

range:0:(open)/1:(close)

(ex.: 1)

Inputting of value Inputting of code Inputting of value

range:0~2

1+#

LED1 LED2 LED3

(on)

(off)(off)

-

When the “ cancel” key is pressed, the indicator will show its standby color,

*

the buzzer beeps, and the system exits the setting mode.

-

When there isn’t any operation within 10s, the indicator will show its standby color,

the buzzer beeps, and the system exits the setting mode.

Beep+

LED1 LED2 LED3

(off)(off)

(ex.: 1)

1+# 1+#1234+#

LED1 LED2 LED3

Beep+

(on)

(on)

(off)(off)

LED1 LED2 LED3

range:0:(normal)/1:(reverse)

LED1 LED2 LED3

Beep+

LED1 LED2 LED3

(off)(off)

*

(Default

Input the setting code.

Normal)(Default 0(opened))

07+#

Beep+, Beep

(flash)(off)(off)

0/1

(ex.: 1)

Beep+

(on)

(off)(off)

(off)

Beep, Beep+

- The unlock mode can be set on
access keypad panel, and the
valid value is the number you set
last time.

- When it is set to 0, pressing the
touch key will blink one time.

- When it is set to 1, pressing the
touch key will sent out a sound of
beep.

- When it is set to 2, pressing the
touch key will blink one time and
sent out a sound of beep.

- Cancel all the passwords except
the master code.

- Restore the master code to
default value(1,2,3,4)

-9-

- When the item is set to 0, press
the button to cancel the input,

*

and press the # button to confirm
the input.

- When the item is set to 1, press
the # button to cancel the input,
and press the button to confirm
the input .

*

Input the master code.

(Default: [ ] +[#])

LED1 LED2 LED3

(on)(off)(off)

Beep+, Beep

9. Tone select

(Default

08+#

LED1 LED2 LED3

(flash)(off)(off)

1(enable))

Beep+, Beep

10.Interference resistant
grade setting

(Default 3)

Input the setting code. Input the setting code.

09+#

LED1 LED2 LED3

(flash)(off)(off)

Beep+, Beep

11.Keyboard mode

(Default:1(scramble))

Input the setting code.

10+#

LED1 LED2 LED3

(flash)(off)(off)

Beep+, Beep

0/1 0/1

Inputting of value (ex.: 1)
range:0(disable)/1:(enable)

1+#

LED1 LED2 LED3

(off)(off)

-

When the “ cancel” key is pressed, the indicator will show its standby color,

*

the buzzer beeps, and the system exits the setting mode.

-

When there isn’t any operation within 10s, the indicator will show its standby color,

the buzzer beeps, and the system exits the setting mode.

(on)

Beep+

Inputting of value (ex.: 3)

range:0~5

3+#

LED1 LED2 LED3

(on)

(off)(off)

Inputting of value (ex.: 0)

range:0(standard)/1:(scramble)

LED1 LED2 LED3

Beep+

0+#

(on)

(off)(off)

12.Unlock work mode

LED1 LED2 LED3

Inputting of value (ex.: 0)

LED1 LED2 LED3

Beep+

LED1 LED2 LED3

(off)(off)

(Default:0)

Input the setting code.

11+#

Beep+, Beep

(flash)(off)(off)

range:0~3

0+#

Beep+

(on)

(off)(off)

(off)

Beep, Beep+

-

-

If the item is set to 0, when unlock,
the system will sent out a sound of
Beep+.

- If the item is set to 1, when unlock,
the system will sent out a sound of

The larger you set the
interference resistant grade,
the stronger it will be, but the
sensitivity of the keypad will
be more lower.

“Door is open”.

-

If the item is set to 0, the
keypoard display mode is
standard mode.

- If the item is set to 1, the
keypoard display mode is
scramble mode.

-10-

- 0:Unlock via password or user
card(only release the first lock).

- 1:Unlock via password or user
card(swipe user card once time to
release the first lock; if swipe user
card twice in a second to release the
second lock).

- 2:Unlock via user card and
password(except the temporary
password).

- 3:Unlock via user card and
password(including the temporary
password).

Input the master code.

(Default: [ ] +[#])

LED1 LED2 LED3

(on)(off)(off)

Beep+, Beep

13. Backup(master / user
card / password / tone)

12+#

LED1 LED2 LED3

Inputting of code

(flash)(off)(off)

Beep+, Beep

1234+#

LED1 LED2 LED3

(on)

(off)(off)

-

When the “ cancel” key is pressed, the indicator will show its standby color,

*

the buzzer beeps, and the system exits the setting mode.

-

When there isn’t any operation within 10s, the indicator will show its standby color,

the buzzer beeps, and the system exits the setting mode.

14.Update(master / user
card / password / tone)

Input the setting code. Input the setting code.

LED1 LED2 LED3

LED1 LED2 LED3

Beep+

13+#

Beep+, Beep

(flash)(off)(off)

Inputting of code

1234+#

(on)

(off)(off)

Beep+

15.Device address
(Default:0 )

Input the setting code.

14+#

LED1 LED2 LED3

(flash)(off)(off)

Inputting of value (ex.: 0)

range:0~3

0+#

LED1 LED2 LED3

(on)

(off)(off)

Beep+, Beep

Beep+

LED1 LED2 LED3

16.RLC control
(Default:0 )

Input the setting code.

15+#

LED1 LED2 LED3

Inputting of value (ex.: 1)

(flash)(off)(off)

range:0~4

Beep+, Beep

1+#

LED1 LED2 LED3

(on)

(off)(off)

(off)

(off)(off)

Beep, Beep+

Beep+

-

When backup, you need to
Insert SD card into the SD card
slot.

.

­Insert SD card(the update file
is stored in SD card) into the
SD card slot.

When update, you need to

-

Device address Settings:
0(device address:0),1(device
address:1),2(device address:2),
3(device address:3).

-11-

-

RLC association control:
0:According to AKP address
auto-correlation;
1:Association of the first RLC;
2:Association of the second RLC;
3:Association of the third RLC;
4:Association of the fourth RLC.

Input the master code.

(Default: [ ]+[#] )

LED1 LED2 LED3

(on)(off)(off)

Beep+, Beep

17.Temporary(single use
only) password for relay1

18.Temporary(single use
only) password for relay2

19.Set the code for
user group 1

20~59 60~99

Input the setting code. Input the setting code.

18+# 19+# 21+# 60+#

LED1 LED2 LED3

(flash)(off)(off)

Beep+, Beep

Inputting of value (ex.: 1006)

1~12 digits

1006+#

LED1 LED2 LED3

(on)

(off)(off)

-

When the “ cancel” key is pressed, the indicator will show its standby color,

*

the buzzer beeps, and the system exits the setting mode.

-

When there isn’t any operation within 10s, the indicator will show its standby color,

the buzzer beeps, and the system exits the setting mode.

Beep+

LED1 LED2 LED3

(flash)(off)(off)

Beep+, Beep

Inputting of code (ex.: 2016)
1~12 digits

2016+# 2012+#

LED1 LED2 LED3

(off)(off)

(on)

Beep+

Input the setting code.
(ex.:21)

LED1 LED2 LED3

(flash)(off)(off)

Beep+, Beep

Inputting of code (ex.: 2011)
1~12 digits

2011+#

LED1 LED2 LED3

(on)

(off)(off)

20.Set the code for
user group 2

Input the setting code.
(ex.:60)

LED1 LED2 LED3

Inputting of code (ex.: 2012)
1~12 digits

LED1 LED2 LED3

Beep+

LED1 LED2 LED3

(off)(off)

(off)

Beep+, Beep

(flash)(off)(off)

Beep+

(on)

(off)(off)

Beep, Beep+

- Once input the correct temporary password to release the door,
the system will clear the temporary password after 60 seconds
automatically. But the password is still valid within 60 seconds after
inputing the correct temporary password.

- The temporary1 is used to release the first lock,and the temporary
2 is used to release the second lock(the second lock need external
device to support).

- If the password exceeds 12 digits, the system will make the sound
of “beep,beep,beep,beep”,and the digitals you input before will be
cleared at the same time.

- The user code group1 is used to release the first lock,and the user code
group2 is used to release the second lock(the second lock need external
device to support).

- The user code group1 and user code code group2 can contain 40
group passwords

- If the password exceeds 12 digits, the system will make the sound of
“beep,beep,beep,beep”,and the digitals you input before will be cleared
at the same time.

- The user code can not be set the same as the master code and
temporary code.

- The temporary code can not be set the same as the master code
and user code.

-12-

Input the master code.

(Default: [ ]+[#] )

LED1 LED2 LED3

(on)(off)(off)

Beep+, Beep

21.Register [Manage card]

100+# 101+# 102+# 103+#

LED1 LED2 LED3

Inputting of code

(flash)(off)(off)

Beep+, Beep

1234+#

LED1 LED2 LED3

(on)(off)

Swipe MASTER CARD ADD card
and MASTER CARD DELETE
card in the ID window.

LED1 LED2 LED3

(flash)(off)

(off)

(off)

Beep+

Beep+

Input the setting code. Input the setting code.

LED1 LED2 LED3

(flash)(off)(off)

Beep+, Beep

Inputting of code

1234+#

LED1 LED2 LED3

(on)(off)

Swipe new user card one by one
to be added in the ID window.

LED1 LED2 LED3

(on)(off)

(off)

(off)

Beep+

Beep+

23.Delete user card 24.Format user card 22.Add user card

Input the setting code. Input the setting code.

LED1 LED2 LED3

(flash)(off)(off)

Beep+, Beep

Inputting of code

1234+#

LED1 LED2 LED3

(off)

(flash)(off)

Swipe user card one by one to be
deleted in the ID window.

LED1 LED2 LED3

(off)

(flash)(off)

Beep+

Beep+

LED1 LED2 LED3

(flash)(off)(off)

Inputting of code

1234+#

LED1 LED2 LED3

(off)

(off)(off)

Beep+, Beep

Beep+

-

When the “ cancel” key is pressed, the indicator will show its standby color,

*

the buzzer beeps, and the system exits the setting mode.

-

When there isn’t any operation within 10s, the indicator will show its standby color,

the buzzer beeps, and the system exits the setting mode.

- Swipe the first card to ID card
window, it will be set to

CARD ADD

MASTER

card.

- Swipe the second card to ID card
window, it will be set to

CARD DELETE

MASTER

card.

- Another way:

MASTER CARD ADD

Swipe the
card to ID card window in standby
mode, and then swipe user cards
one by one to be added.

- Another way:
Swipe the
card to ID card window in standby
mode, and then swipe user cards
one by one to be deleted.

MASTER CARD DELETE

-When registered new master
cards, the old master cards are
invalid automatically.

-13-

LED1 LED2 LED3

(off)

(off)(off)

Beep, Beep+

6.Unlock Operations

Unlock by user code

When the registered user code has been input using the keypad (1~12 digits), the digitron will display “OP1”
or “OP2”, and the LED1 indicator lights up, and the system will synthesis sound of “Door is open”(If the Tone

Select item is set to 1), then the electric door strike is unlocked.(note that you should press "#" button(if "#"

button is set to conrm button) after input the unlock code)

• The time interval between 2 digitals' input must be less than approximately 10 seconds. otherwise the input
value will be cleared.

• If you make a mistake when inputting the user code,press the" cancel" button and input the user code again.

• The release function is forbidden and the input operation is disabled for 60 seconds if 10 times incorrect
access codes are continuously attempted. During this time,the buzzer will continuously sound about 8 times.

Unlock by user card

When the registered user card has been shown to ID card window, the digitron will display “OP1”(if swipe user

card twice in a second in the ID card window, the digitron will display “OP2”), and the LED1 indicator lights up,
and the system will synthesis sound of “Door is open”(If the Tone Select item is set to 1), then the electric door

strike is unlocked.

7.Specications

• Power Supply : DC 24V;

• Power Consumption: Standby 23mA; Working status 43mA;

• Unlocking time: 1~99s

• Lock Power supply: 12Vdc, 280mA(Internal Power);

• Number of relay circuits: 2(the second lock need external device to support)

• Mounting: Surface mounting

• Working temperature: -15ºC ~ +55ºC

• Dimension: 151(H)×95(W)×37(D)mm

-14-

• Please clean the unit with soft cotton cloth, don't use the organic impregnant or chemical clean agent. If
necessary, please use a little pure water or dilute soap water to clean the dust.

• The unit is weather resistant. However do not spray high pressure water on access control keypad directly.

Excessive moisture may cause problems with the unit.

• You must use the right adaptor which is supplied by the manufacture or approved by the manufacture.

• Pay attention to the high voltage inside the products, please refer service only to a trained and qualified
professional.

•The design and specications can be modied without notice to the user. Right to interpret and copyright of

this manual are reserved.