XtendLan D-2Wire User Manual

Download

D2-wire

Video Intercom system Technical guide

CONTENT

Section1 - Introduction 1

System Features

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

System Capacity

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

System Extension

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

System Function

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Section2 - Units and Installations 4

Door Station

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Features

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Parts and functions

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Place Name Plate

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Electronic Specifications

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Standard Installation

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Installation with expanding panel

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Terminal Descriptions

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Door Station wiring

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

DIP Switches settings

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Door Station Lock Connections

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Proximity ID Card Operation

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Monitor

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Features

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Electronic Specifications

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Terminal Descriptions

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Intercom function

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

CameraAuto Switching

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Color Picture Memory

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

SD Card

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

User Code Setup

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Monitor Extending Connection

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Accessories

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

PS5-Power Supply

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

DPS

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

DBC

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

DBC-4 Unit

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

DPS-4 Unit

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

DCU Unit

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Section3 - Cables and Connections 28

General Rules for Installation

- - - - - - - - - - - - - - - - - - - - - -

Connecting the Connectors

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Installation Height

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Door Station Install Condition

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Table of Cables and Distance

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

System Wirings and Connections

- - - - - - - - - - - - - - - - - - -

1. Basic IN-OUT wiring mode

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

2. Basic IN-OUT wiring mode (1~n risers)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

3. IN-OUT wiring with One-user distributor

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

4. Basic Star wiring mode

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

5. 4 Door Stations and star wiring mode

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

6. 1 Door Station and 2 CCTV cameras

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

7. Mixed 1/4 user distributors wiring

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Section4 - Setup and Debug 37

System Operations

- - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Busy State Management

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Door Station Function

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

System Setup

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

What’s User Code

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

What's SlaveAddress

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Online search

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Simulating Call

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Section5 - XL CONFIG Software 43

Introduction

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Hardware connection

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Interface Preview

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Section1 - Introduction

System Features

• With only 2 wires (no polarity) throughout the whole installation, the 2-wire DPC is a simplified installation system with minimum wiring and powerful features. The minimum wiring drastically reduces installation times and errors. By means of FM video modulation and ASK data transmission technology, system provides better protection against interference, which guarantees best color quality at all points of the installation.

• Centralized power supply for the entire system. With advanced power management, the whole system use only one power supply, so there is no power supply needed for any Monitor or other system parts.

• Use Plug-in connectors and DIPswitchers for more rapid installation.

• Flexible cable connection to wire, support in-out, branching and mixed mode.

• Multi Monitors for one apartment/house in same User Code, and automatically swithing the video.

• Online searching and diagnose function for installer.

• Using PC to program and diagnose the system.

System Capacity

• Max. 4 Door Stations, or 3 Door Station plus 2 CCTV cameras, or 1 Door Station plus 6 CCTV cameras.

• Max. 32 Monitors in a system, max.4 Monitors in same User Code.

• Proximity access control function, max. 1000 user ID cards.

• Maximum 150 meters distancefrom Door Station to the farest Monitor.

System Extension

• Connect Door Strike and Exit Button to Door Station directly.

• Connect door bell and extra ringer to Monitor directly.

• Control staircase light or relay executors for second electronic lock.

• Connect up to 6 CCTV cameras by DCU unit.

System Function

• Name list intercom

• Inner call intercom among Monitors in same Room Code

• One Monitor can be programmed as Guard unit

• Color Memo or SD card DVR function

DPC-System-Technical

VillaApplication

Although the DPC is mainly designed

CALL UNLOC

K TALK/MO N

IN - USE

CALL UNLOC

K TALK/MO N

IN - USE

CALL UNLOC K TALK/MO N

IN - USE

CALL CALL

for the small apartment system usage, it can be used in villa or villa group applications. Multi Monitors can be installed in a family with the same User Code, or many houses can be connected as one system, and all of these Monitors can have calling conversation each other.

UNLOC K TALK/MO N

IN - USE



UNLOC K TALK/MO N

IN - USE

CALL

UNLOC

TALK/M

IN-USE

CALL

UNLOC

TALK/M

IN-USE

CALL

UNLOC

TALK/

MON

IN-USE

CALL

UNLOC

TALK/

MON

IN-USE

ApartmentApplications

This is the most common way that the system is used. One building or multi buildings can be connected as one system. Every apartment can open the door, and the users in the system can have intercom talk each other.

DPS

PS5

DPC-System-Technical

Section2 - Units and Installations

Door Station

Bit-4=off

1 2 345 6

DPC-D211E-8ID

DPC-D211E-8S DPC-D211E-24D

Bit-4=on

12 34 56

Features

DPC-D211E-4ID DPC-D211E-4S DPC-D211E-12S

• Full anodize aluminum panel.

• SONY color CCD camera.

• camera angle adjustable.

• ID card access control

• Night-view LED with CDS light sensor.

• Backlit name plate for each button.

• Use DIP switches for multi Door Station configuration.

• Direct connect to electronic lock of 12Vdc.

• Exit button.

• USB-RS485 interface to connect to computer.

• Plug-in connector to connect bus line.

• On line Monitor search.

308

298.5

Parts and functions

Camera Lens

CDS Sensor InfraredLED

Speaker

Microphone

Name

plate

Call

button

CameraAngle adjustment

SpeakerVol adjustment

Connection

Board

123 mm

18 mm

45 mm 114.5 m m

Place Name Plate

Press down and shift right/left to open the transparent name plate cover, then insert the name paper, then put the plate cover back to the panel. Note thar double button line panel can be opened both direction, single button line Can only be opened at right side.

Electronic Specifications

Power supply: 24Vdc(supplied by PS5) Power Consumption: 1W in standby, 15 W in working Unlock Power output: 12Vdc 300mA NO, COM exchange contact: Max. 48V dc 1.5A Monostable relay activation time: 1 second to 10 minutes ±5% Working temperature:

5ºC +45ºC

DPC-System-Technical

+12V

T/R -

LK- (GND)

T/R+ LK+(COM) N.O. EB+ EB-

L1 L2

1 2

BUS

298.5

1 2 3 4 5 6

SET

485

Standard Installation

Installation with expanding panel

Camera Angle adjustment

Open the mounting box of the panel, use a cross screw to adjust the view angle of the camera before installation.

Jointer*2

Note

Stopper

The double button line expantion panel can only be connected to double button line Door Station; the single button line expantion panel can only be connected to single button line Door Station. For example, the DPC/Dx can only be connected toDPM/Dx Door Station.

1 2 3 4 5 6

BUS

1 2 3 4 5 6

SET

485

SET

485

485 SET

Terminal Descriptions

+12V

T/R

LK -

(GND) LK+(COM) N.O.

EB+ EB

T/R+

DMR11

Connection

Board

+12V

T/R

1 2

LK- (GND) LK+(COM) N.O.

EB+ EB

1 2 3

T/R+

L1 L2

BUS

•

+12V:

12VDC power output.

•

LK-(GND):

power ground.

•

LK+(COM):

electronical load activation relay contact common.

•

NO.:

electronical load activation relay normally open contact (the default setting for this terminal is NO, this terminal can be configured to NC, normally-closed contact by the XL CONFIG software). That means, by default, only the power-to-unlock type of electronic lock can be connected to the COM and NO terminal, if using the power-off-to-unlock type locks, the NO terminal must be set to NC contact by the XL CONFIG software.

•

EB+:

Exit button.

•

EB-:

Exit buton.

•

JP-LK:

For electronic lock safety type setting(refer to Door Station Lock Connections).

•

T/R-:

USB-RS485 communication terminal negative.

•

T/R+:

USB-RS485 communication terminal positive.

•

SET:

DIP switches for system configurations.

•

PA:

Press once to sent the name list to Monitor; press and hold for 3 seconds to add Master card.

•

PB:

Press once to search the Right line Monitor; press and hold for 3 seconds to search left line Monitor.

•

Bus(

L1,L2):non-polarity bus line.

Door Station wiring

This example is one Door Station wiring, note that the lock used here is a 12Vdc 300mApower-to-unlock type.

+12V LK - (GND) LK+(C OM)

N.O. EB+ EB -

T/R T/R+

Outlet Button

L1 L2

2 3

Connect to DPS or DPS -4

DPC-System-Technical

12 34 56

DIP Switches settings

Total 6 bits in the DIPswitches can be configured.The switches can be modified either before or after installation.

• Bit-1 and Bit 2is for Door Station IDsettings,when mutil Door Stations are installedin the system, these two bit

ON(1) OFF(0)

1 2 3 4 5 6

must be set correctly,the firstDoorStationset to 00, the second one set to 01, thethirdoneset to 10, the fourth one set to 11. If only one Door Station is installed, set to 00.

• Bit-3: Single line button Door Station or double line buttonDoor Station selection. If the Door Station isa double line button, for examlpe, the DMR11-D8, set this bit to 0, set to 1 for single line button Door Stations.

• Bit-4: Button code selection; if use the default codes for each button of the Door Station, set to 0, if use the programmed codes, set to 1.(the code for each button can be programmed by the XL CONFIG software, see the program section in this manual)

• Bit-5: Unlocking timequick selection, by default it isset to 0, for1 second unlocking time; set to 1 for 5 seconds. (this 5 second unlocking time can be changed by XL-CONFIG software)

• Bit-6: MUSTbe set to off.

Bit definition Bit state Function Descriptions

Default setting, ID = 0, set to the first Door Station.

Bit-1 and bit-2

Door Station ID setting

ID = 1, set to the second Door Station.

ID = 2, set to the third Door Station.

ID = 3, set to the fourth Door Station.

Bit-3

User ID select

Default setting for using a double line button Door Station.

when using a single line button Door Station.

Bit-4

Button line select

Default setting for using the default codes of the button.

using the progremmed codes of the button.

Bit-5

Unlocking time quick select

Default setting, unlocking time = 1 second.

Unlocking time = 5 seconds.(can be changed by software)

Bit-6

Function reserved

Working state.

Function reserved.

1 2 3 4 5 6

JP_LK

1 2 3 4 5 6

485 SET

Door Station Lock Connections

+12V

T/R -

LK - (GND) LK+(COM) N.O.

EB+ EB -

T/R+

DMR11

Connection Board

+12V

T/R-

1 2

LK- (GND) LK+(COM) N.O.

EB+ EB-

T/R+

BUS

2 3

BUS

1. Direct lock connection

Use the power of the system to supply for the electronic lock, so that the lock can connect to the Door Station directly, without a additional power supply for the electronic lock. Note that the Door Station can only output a 12Vdc power, therefore the kind of lock used is limited.

• The rated power of the lock must be less than 12Vdc 300mAwhen using direct lock connection method.

• The GND must connect to the negative of the lock, and the COM connect to the positive .

• Jumper set to 1-2 position for Power-to-Unlock safety type; set to 2-3 position for Power-off-to-Unlock type(in this case theUnlock Relaymode should be set to Normally Closed onXLCONFIG software)

• The 5th bit of the DIP switches is for the unlocking time setting, it's set to off by default, for 1 second unloking time. If set this bit to on, the unlocking time is 5 seconds.

• If different unlocking time is needed to be configured, the XL CONFIG software can be used to change the

Unlock Timing on the Parameter tab(see the program section).

A. Connection for Power-to-Unlock type:

12V 300mA

Jumper set to 1 -2 position

+12V LK - (GND) LK+(COM) N.O. EB+ EB -

1 2 3

DIPS

1 2 3 456

DIPS-5: default set to off, unlocking time is 1 second. (In most cases, 1 second is work for Power-to-Unlock type)

DPC-System-Technical

JP_LK

B. Connection for Power

- -

off-to-Unlock type:

12V 300mA

+12V LK - (GND)

N.O. EB+ EB -

DIPS

1 2 3 456

DIPS-5: set to on, unlocking time is 5 seconds.

Jumper set to 2 -3 position

set to Normally Closed on the

Unlock Relay mode on DT software.

2. Additional power supply

When the electronic lock is over 12 Vdc, additional power supply for the lock is needed.

• The power supply for the lock must be less than 48Vdc 1.5A.

• The Jumper must be removed when using additional power supply. The default is set for Power-to-Unlock type(Normally open), if use Power-off-to-Unlock type, change the Unlock Relay mode to Normally closed on the Parameter tab ofXL CONFIG software.

• If different unlocking time is needed to be configured, please use theXL CONFIG software to change thesetting on the Parameter tab(see the program section).

C. Connection for Power-to-Unlock type:

Note:

Cut off this line when using

additional power supply

Remove the Jumper set to Normally Open on the Unlock Relay mode.(default)

+12V LK - (GND) LK+(COM) N.O. EB+ EB -

1 2 3

DIPS

1 2 3 456

DIPS-5: default set to

off,

unlocking time is 1

second.

(In most cases, 1 second

work for

Power-to-Unlock type)

D. Connection for Power

- -

off-to-Unlock type:

Note:

Cut off this line when using

additional power supply

Remove the Jumper

set to Normally Closed on the

+12V LK - (GND) LK+(COM) N.O. EB+ EB -

1 2 3

DIPS

123456

DIPS-5: set to on, unlocking time is 5 seconds.

Unlock Relay mode on DT software.

Proximity ID Card Operation

• Up to 1000 user cards can be registered by the Door Station.

• Easy management with LED state and Sound hint.

• There are two master cards, one MASTER CARD ADD card and one MASTER CARD DELETE card,When adding a new master card, the old one will be replaced automatically.

• Card reading distance is from 3 to 5 cm.

The Master cards are necessary when you add or delete user cards, Please keep the Master cards carefully. However, it is much easier to manage the ID cards usingXL-CONFIG software.

How to add user cards:

DMR11/ID/D8

Show the MASTER CARD

ADD card in standby.

Note. sounded Di~,Di

Show the cards to be added, one by one. Note. Long beep if add success, two long beep if repeated.

Show the MASTER

CARD ADD card again to

exit. However, will exit if no card was showed within 15s.

How to delete user cards:

Show the MASTER CARD

DELETE card in standby.

Note. sounded Di~,Di

Show the cards to be deleted, one by one. Note. Long beep if deleted successfully

Show the MASTER

CARD DELETE card

again to exit. However, will exit if no card was showed within 15s.

How to delete all user cards(formating):

Show the MASTER CARD

DELETE card in standby.

Note. sounded Di~,Di

Show theMASTER CARD

ADD card to run format

operation.

Show the MASTER CARD

ADD card again within

3 seconds to confirm the Format operation.

Authorize master cards:

When Door Station is in standby, pressPAbutton and hold for 3 seconds to get into the master card manage state

Show the card to be autorized as MASTER CARD ADD , you will hear a long beep*

show the card to be authorized asMASTER

CARD DELETE, and

then the Reader willexit out automatically.

DPC-System-Technical

LED-D LED-C LED-B LED-A

Add user cards by Room:

Show the MASTER CARD

ADD card in standby

Press a certain button on the Door Station, then show the cards which to be assigned to this Room.Then press an other

button and show the cards.....

Show the MASTER

CARD ADD card again to

confirm and exit.

Delete user cards by Room:

Show the MASTER CARD

DELETE card in standby

Press the button(s) that the cards belong to on the Door Station.(all cards belong to the room will be deleted)

Show the MASTER

CARD DELETE card

again to confirm and exit.

Note 1: The MASTER CARDADD card must be showed beforethe Reader can get in to theAuthorize DELETE

Card state, and make sure each operation have to take place within 10 seconds, or the Door Station will return to normal state automatically.

Card management shoud hints

State Operation Sound hint

standby state

Card

management

state

show user card(registered) a long 'D~.' (door opens)

show user card(not-registered) 3 short 'Di' (Di, Di ,Di)

Enter the card management state a long 'Di~' + a short 'Di' (Di~ Di)

Exit out the card management state

2 short 'Di' (Di ,Di)

Add card/Delete card/Format successful

a long 'Di~' (Di~)

Add a already existed card

2 long 'Di~' (Di~, Di~)

Add card/Delete card/Format unsuccessful

3 short 'Di' (Di, Di, Di)

Add a debug card(16666666)

4 short 'Di' (Di, Di ,Di, Di)

Add card failure (1000 cards registered)

5 short 'Di' (Di, Di ,Di, Di, Di)

Card management LED hints

State

LED-A

LED-B

LED-C

LED-D

Standby

ONONON

AuthorizeADD-Card

OFF

Authorize DELETE-Card

OFFONOFF

Add user card

OFF

Delete user card

OFFONOFF

OFF

Format

ONONOFF

OFF

DMR11/ID/D8

BT1

DIPS

BT2ONL1

Monitor

Features

LCD

screen

LED

Indicator

LCDTouch Screen Microphone

POWER

CALL

CALLbutton

IN-USE

INTERC OM

UNLOC K

TALK/

MONIT OR

Button

Button INTERCOM Button UNLOCK Button

TALK/MON Button Microphone

UNLOCK

TALK/MON

IN-USE

UNLOCKbutton TALK/MONbutton LEDindicator

Speaker

MountingHook

VentilationVent

Connection Port

MountingHook

BT1

DIPS

Mounting Hook

BT2 EH GN D VD

1 2 3 4 5 6

ConnectionPort

Mounting

Hook

• Touch screen optional.

• 128 pieces color picture memory optional.

• Using DIP for Monitor ID setting.

• Using plug-in connector.

• On screen namelist for intercom.

• No additional power supply needed(suppliedby system).

• TV-OUT function for connecting theTV.

• Additional door bell call button

• External ringer connection

Electronic Specifications

Power supply: 24Vdc(supplied by DPS) Power Consumption: 1W in standby, 10 W in working Working Currency: Max.30mA in standby, 500mA in working TV output signal: 1V

p -p

CVBS

External Ringer: 12Vdc 100mA

DPC-System-Technical

Terminal Descriptions

Monitor

Connection Board

SW+

•

SW+:

Door bell call button.

•

SW-:

Door bell call button.

•

EXT-RING:

External ringer output(12Vdc 100mA)

SWEXT-RING GND VIDEO

1 2 3 4 5 6

BUS

•

GND:

Ground.

•

VIDEO:

Video signal output.

•

S1:

DIP switches for system configurations.

•

BUS:

non-polarity bus line.

Intercom function

There are three kinds of intercom function available in theDPC.

1. Guard Unit Call

A Monitor can be assigned to be the guard unit Monitor, by setting on the OSD screen of the Monitor. When the user's Monitor is in standby, press call button or intercom button, the intercom page will show up on the screen, than select and confirm 'Call Guard Unit' item, and the Monitor will call the guard unit Monitor, when the guard unit Monitor answers the call, conversation with the guard person is started.

2. Inner Call

When multi Monitors are installed in one apartment, inner call is availlable. Note that all Monitors should have the same User Code, and the Master and Slave address should be set on the Monitor(see page 40 for detail information).

When the Monitor is in standby, press call button or intercom button, the intercom page will show up on the screen, than select and confirm 'Inner Call' item, and other Monitors will ring at the same time. When any Monitor answers the call, other Monitors will stop ringing and go back to standby state.

3. Intercom Call (Namelist)

The namelist intercom is for apartment to apartment calling. The user in one apartment can call other apartments by selecting the name on the screen. In this way, it's no need to remumber the ID(User Code or room address) of the other users. A complete namelist of all theusers in the system can be upload to the Door Station by the XL CONFIG software, and then the Door Station will send the namelist to all Monitors.

Step 1: Run the XL CONFIG software. Connect the USB-485 Convertor to the DMR11 Door Station and the PC, double click the software to make it running on the PC, then click the Namelist tap, the screen will be showed:

Step 2: Edit the namelist. In the name inputfield, thereare a Room No. colume and a Name Lablecolume, each

User Code have a corresponding Room No. and a Name Lable. Input all the names in theName lable field for

each User Code, then click Download Namelist Button to download the namelist to the Door Station, and the Door Station will sent the data to all the Monitors in the system.

Step 3: Calling people using the namelist. After downloaded from the PC, every Monitor will have a built-in namelist. To access the namelist, go to the Main menu, select Intercom - -> Intercom Call to enter the intercom namelist screen(see the picture bellow), and then just select the user name to call the other apartment.

Intercom Function Intercom Call Inner Call Direct Call Guard Unit Exit

[0101] Jim

Zhang

[0102] Cherry

Shi

[0201] David

[0202] Calo

Lou

[0301] Samuel

Intelligent Home S y s tem

Intelligent Home S y s tem Intelligent Home S y s tem

DPC-System-Technical

Camera Auto Switching

When multi Dooor Stations or CCTV cameras are installed in the system, Monitor can display the video one after another.The Monitoring time for each Station or Camera must be set by the XL-CONFIG software manually to enable the Auto Switching function(XL-CONFIG

- -

>Parameter

- -

>Camera Swithcing Time). Also, you can touch the icon on

the screen to monitor a specific camera only.

Color Picture Memory

Total 128 pcs picture canbe stored in the Monitor. User can both record the picture manually and set the Monitor to automatically record pictures.

• Manually record: when the Monitor is in monitoring or talking state(the screen is turned on), press the record icon on the touch screen or press a record button, the current picture which show on the screen will be saved into the built-in flash memory of the Monitor.

• Automatically record: A picture will be saved after 2 seconds the visitor pressed the call button on the Door

Station.To enable the auto record function, go to the Main

- -

>Setup menu, and turn on the 'Auto Record' item.

• Pictures can be delect manually using the touch screen.

• When the memory is full(about 128 pcs), the oldest picture will be replaced by the latest saved piture.

SD Card

Built-in SD card reader, maximum 2 GB supported.

• Video and audio(DVR) record: Automatically or manually record can be set in need, total 4.5 hours recording time; play back on the Monitor or on the PC.

• Digital Photoframe: play back the pictures (JPEG format only) on the SD card using a slide show as photoframe.

• MP3 background music:The MP3 files on the SD card canbe played as a background music.

Bit state

Setting

Bit state

Setting

12 345 6

Monitor not at the end of the

line.

12 345 6

Monitor at the end of

the line.

User Code Setup

In the DPC, every apartment must have a unique identification called User Code. The DIPswitches are usedto configure the User Code for each Monitor.

• Bit-1 to Bit-5 are used to User Code setting. The value is from 1 to 32, which have 32 different codes for 32 apartments.

• When multi Monitors are installed in one apartment, these Monitors have to use the same User Code setting, and the Master/Slave mode should be set on the Monitor.

• Bit-6 is line terminal switch,whichhave to be set to ON ifthe Monitor is in the end of the line(bus), otherwise set to OFF.The end of the line is terminal that no other section will start from it.

Bit-6 line terminal setting:

1 2 3 4 5

ON(1)

OFF(0)

Bit state User Code Bit state User Code Bit state User Code

Code=1

12 345 6

Code=12

12 345 6

123 4 5 6

Code=23

Code=2

Code=13

Code=24

12 345 6

Code=3

12 345 6

Code=14

123 4 5 6

Code=25

12 345 6

Code=4

12 345 6

Code=15

123 4 5 6

Code=26

12 345 6

Code=5

12 345 6

Code=16

123 4 5 6

Code=27

12 345 6

Code=6

12 345 6

Code=17

123 4 5 6

Code=28

12 345 6

Code=7

123 4 5 6

Code=18

123 4 5 6

Code=29

12 345 6

Code=8

123 4 5 6

Code=19

123 4 5 6

Code=30

12 345 6

Code=9

123 4 5 6

Code=20

123 4 5 6

Code=31

12 345 6

Code=10

123 4 5 6

Code=21

123 4 5 6

Code=32

12 345 6

Code=11

123 4 5 6

Code=22

123 4 5 6

12 345 6

123 4 5 6

DPC-System-Technical

SW+

SW-EXT

RING

GND

VIDEO

BT1

DIPSEHGND

1 2 3 4

5 6

Monitor Extending Connection

POWER

IN-U SE

CALL

UNLOCK

TALK/MO N

IN-USE

INTERC OM

UNLOCK

TALK/

MONITO R

1 2 3 4 5 6

SW+

SW-

EXT-RI NG GND VIDEO

L1 L2

1 2 3 4 5 6

BT1

DIPS

L1 L2

BT2 EH GN D VD

1 2 3 4 5 6

1. Door Bell Call Button

Additional door bell call button can be connected to the Monitor, so that the visitors can ring the door bell again in front of the user's apartment. When the call button is pressed, the Monitor will output ring tones but the screen will keep off, and the external ringer will ring at the same time(if a external ringer is installed).

Door bell call button

SW+ SWEXT-RING GND VIDEO

2. External Ringer

External ringer can be connected to the Monitor. The ringer

External Ringer

= = will ring whenever the Door Station call button or the door = bell call button is pressed, and it will stop ringing when the Monitor rejucted or answered the call.

12Vdc 300mA

SW+ SWEXT-RING GND VIDEO

3. TV-out function

Connect television to the Monitor, when the Door Station calls, the user switch the channel to the AV channel, and the visitor's video will show up on the screen of the television. The core of the video cable must connect to the VD terminal, and the shielded layer connect to the GND.

Television

video cable

SW+ SWEXT-RING GND VIDEO

Accessories

PS5-Power Supply

The PS5 power supply unit is designed for DPC to supply up to 32 Monitors and total 4 Door Stations at the same time.

• UniversalAC input/full range.

• Multi protection: short sircuit, overload, over voltage

• Cooling by free air convection

• DIN rail mounting.

• Support up to 32 Monitors

• Support up to 4 Door Stations.

Dimension and Terminal

152. 5

L ( AC) N (AC)

V-

V+

VADJ

LED

•

L(AC):

AC input.

•

N(AC):

AC input.

•

Earth Ground.

•

V-:

DC power output.(21.5~26.5 adjustable)

•

V+:

DC power output.(21.5~26.5 adjustable)

6.5

159

150

•

VADJ:

Output voltage adjustment.

•

LED:

Working state indicator.

22 117

Unit: mm

Electronic Specifications

Input Voltage: 85~260Vac, 120~370Vdc Input Frequency: 47~63 Hz Leakage Current: >2mA / 240Vac AC current (TYP.) 1.5A /150Vac, 0.9A / 230Vac Output VADJ range: 21.5~26.5 Vdc adjustable Rated Voltage: 24Vdc Rated Current: 3.2A Rated Power: 76.8W

DPC-System-Technical

DIN Installation

DPS

PS5

DIN

nail

85~260AC

DPS

DPS:

This unit is a power supply adaptor for the PS5 or PS4 power supply, it transfers the power from the power supply to the suitable power for the non-polarity bus. Note that the DPS must work together with the PS5 or PS4 power supply.

DPS

Connect

Power

Supply(PS5)

Connect to Door

Station

Connect to

Monitor

Technical Specifications(DPS)

Power input: 24Vdc (supplied by PS5) Power output: 18Vdc Power Consumption: 0.25W in standby, 0.5 W in actting Working temperature:

5ºC +45ºC

DBC

DBC:

This unit is a single user distributor unit used to transferall data betweenthe Monitor and the Bus Line. Every Monitor(except the last one at the end of the line) needs one DBC to connect to the Non-polarity Bus Line. No extra power supply needed, and one LED indecatior to show the working state.

DBC

Bus In /Out

Bus Out(to Monitor)

Technical Specifications(DBC)

Power Consumption: 0.25W in standby, 0.5 W in working Working temperature:

5ºC +45ºC

DPC-System-Technical

DPS/DBC Dimensions

Direct Wall Mounting DIN Rail Mounting

Use the screws to fasten the unit onthe wall directly. Install on the DIN Rail.

85mm

DBC-4 Unit

DBC-4

Distributor is a 4 output user distributor for DPC, to approach the star topology connection in the

apartment system. See Section 3 Cables and Connection for detail connection information.

set to 120 for the last DBC-4

on the building, the others

must be set to HI.

120

Video Match

DBC-4

In-use Power

Trunk Bus

D C B A

Bus Out Bus In

Connect to Monitors

DPS-4 Unit

DPS-4

Unit is used to connect multi Door Stations, total 4 Door Stations can be connected to the DPS-4 unit.

Trunk

Bus

D C B

Connect to

Monitor/Distributor

Connect to DPS

Connect to Door Stations

DPC-System-Technical

88mm

13mm

36mm

62mm

DBC-4/DPS-4 Dimensions

140mm

70mm

upward

84mm

32mm

Trunk

Bus

D C B

A/B/C/D port: Connect to Monitors/Door

Station

Trunk Bus: Bus

input/output.

120

Direct Wall Mounting DIN Rail Mounting

DCU Unit

The DCU unit is a Multi function device which can connect2 CCVTcameras and light/lock control.

COM

EB+ EB-

DIP1 DIP2 P1

•

COM:

Contact relay Common terminal

•

NC:

Contact relay Common terminal

•

EB+, EB-:

Contact activate button

BUS-IN

BUS-OUT

BUS-DS

+12

GND

1 2 3 45 6 1 2 3 4

DCU

LED 2 LED 1

VD VG GND

•

DIP1:

Main DIPswitches

•

DIP2:

Switches for Lock/Light control

•

P1, P2:

Contact relay Common terminal

•

BUS-IN:

Connect to Door Station

•

BUS-OUT:

Connect to Monitors

•

BUS-DS:

Connect to Door Station

•

LED1, LED2:

Indecators

•

+12:

Power+ for CCTV camera

•

GND:

Power-for CCTV camera

• VG: Video Ground for CCTV camera

+12

•

VD:

Video Core for CCTV camera

Terminal Connections

ON ON

123456 1234

DCU

Connect to

DPS

Connect to

Monitor/Distributor

Connect to

Door Station

DPC-System-Technical

Dimensions

Direct Wall Mounting DIN Rail Mounting

80mm

DPC-System-Technical

Section3 - Cables and Connections

General Rules for Installation

Connecting the Connectors

Before screw the wire tothe plug-in connector,it'simportant to process the wireinthe correct way.See the following steps to connect the wire.

1. Strip the wire 2. Twist and bend

~12mm 7~8mm

3. Put only the insulation-free part in theterminal

Installation Height

The recommended installation height of both Door Station and Monitor is from 160~165 cm.

CALL

UNLOC

TALK/M

IN-USE

160~165 cm

Door Station Install Condition

The Door Station can not be installed in a place that hard/large light sources can cover the lens of the camera(for exmaple, the street light or Sun light), other wise the video image will have lower contrast. If there is no way to avoid this condition, the alternative is to install the Door Station in a higher position and then adjust the camera angle towards down to keep the lens away from the light source.

Cable Usage

ABC

Twisted cable 2x0.75 mm

606030

Twisted cable 2x1 mm

808040

Cable Usage

ABC

Twisted cable 2x1 mm

703020

Twisted cable 2x1.5 mm

705030



Table of Cables and Distance

The maximum distance of the wiring is limited in the DPC. Using different cables may also effect the maximum distance the system can reach.

The farest

monitor

CALL

UNLOCK

TALK/MON

IN-USE

CALL

UNLOCK

TALK/MON

CALL

UNLOCK

TALK/MON

IN-USE IN-

USE

DBC

When Monitor quantity < 20

DPS PS5

When Monitor quantity > 20

The wire for the Non-polarity bus MUST non-shielded!And usingthe twisted wire is recommended, if using the Non-twisted wire, the total distance will be half.

DPC-System-Technical

System Wirings and Connections

1. Basic IN-OUT wiring mode

CALL

UNLOCK

TALK/MO

IN-USE

Code=32, DIP -6=on

12 3 45 6

Code=31, DIP -6=off

CALL

UNLOCK

TALK/MON

IN-USE

CALL

UNLOCK

TALK/MO

12 3 45 6

Code=1, DIP -6=off

IN-USE

DPS

PS5

85~260AC

ID=00

1 23 4 5 6

2. Basic IN-OUT wiring mode (1~n risers)

CALL

UNLOCK

TALK/MON

CALL

UNLOCK

TALK/MON

123456

Code=8, DIP -6=on

INUSE

123456

Code=4, DIP -6=on

IN-USE

CALL

UNLOCK

TALK/MON

CALL

UNLOCK

TALK/MON

123456

INUSE

123456

IN-USE

Code=7, DIP -6=off

Code=3, DIP -6=off

CALL

UNLOCK

TALK/MON

CALL

UNLOCK

TALK/MON

123456

Code=5, DIP -6=off

INUSE

123456

Code=1, DIP -6=off

IN-USE

DBC

DBC DPS

PS5

85~260AC

ID=00

12345 6

DPC-System-Technical

UNLOCK

TALK/MO

IN-USE

1 23 4 5 6

DBC

3. IN-OUT wiring with One-user distributor

1 2 3 4 5

CALL

1 2 3 4 5

CALL

UNLOCK

TALK/MON

IN-USE

Code=32, DIP - 6=on

Code=31, DIP - 6=off

1 2 3 4 5

CALL

UNLO CK

TALK/M ON

INUSE

1 2 3 4 5

CALL

UNLOCK

TALK/MON

IN-USE

Code=30, DIP - 6=on

Code=29, DIP - 6=off

1 2 3 4 5

CALL

UNLO CK

TALK/M ON

INUSE

1 2 3 4 5

CALL

UNLOCK

TALK/MON

IN-USE

Code=9, DIP - 6=on

Code=8, DIP - 6=off

1 2 3 4 5

CALL

UNLO CK

TALK/M ON

INUSE

1 2 3 4 5

CALL

UNLOCK

TALK/MON

IN-USE

Code=2, DIP - 6=on

Code=1, DIP - 6=off

DPS

PS5

85~260AC

ID=00

UNLOCK

TALK/MO N

UNLOCK

TALK/MO

IN-USE

1 23 4 5 6

DBC

OUT IN

A B C D

OUT IN

A B C D

4. Basic Star wiring mode

CALL CALL

1 2 3 4 5

Code=32, DIP -6=o n

UNLO CK

TALK/M ON

INUSE

1 2 3 4 5

Code=31, DIP -6=on

UNLOCK

TALK/MON

IN-USE

Code=30, DIP -6=on

CALL

UNLOCK

TALK/MON

IN-USE

Code=29, DIP -6=on

CALL CALL

1 2 3 4 5

Code=4, DIP -6=on

UNLO CK

TALK/M ON

INUSE

1 2 3 4 5

Code=3, DIP -6=on

UNLOCK

TALK/MON

IN-USE

CALL

UNLOCK

TALK/MON

1 2 3 4 5

IN-USE

Code=2, DIP -6=on

Code=1, DIP -6=on

DPS

PS5

85~260AC

ID=00

DPC-System-Technical

CALL

UNLOCK

TALK/MO

IN-USE

DBC

OUT IN

A B C D

5. 4 Door Stations and star wiring mode

CALL

UNLOCK

CALL

UNLOCK

1 2 3 4 5

Code=4, DIP - 6=on

TALK/M ON

INUSE

1 2 3 4 5

Code=3, DIP - 6=on

TALK/MON

IN-USE

1 2 3 4 5

CALL

UNLOCK

TALK/MON

IN-USE

Co de=2, DIP -6=on Code=1, DIP - 6=on

DPS-4

DPS PS5

BUS

A B C D

85~260VAC

ID=00

ID=10

1 23 4 5 6

ID=01

1 23 4 5 6

ID=11

1 23 4 5 6

CALL

UNLOC

TALK/M O

IN-USE

DBC

OUT IN

A B C D

6. 1 Door Station and 2 CCTV cameras

1 2 3 4 5

Code=4, DIP -6=on

1 2 3 4 5

Code=3, DIP -6=on

CALL

UNLOC K

TALK/M ON

IN-USE

1 2 3 4 5

CALL

UNLO CK

TALK/M ON

INUSE

1 2 3 4 5

CALL

UNLOC K

TALK/M ON

IN-USE

Code=2, DIP -6=on Code=1, DIP -6=on

1 23 4 5

DCU

DPS

PS5

85~260VAC

ID=00

123456

DPC-System-Technical

1 2 3 4 5

CALL

UNLOCK

TALK/MO

IN-USE

CALL

UNLOCK

TALK/MO

IN-USE

DBC

A B C D

OUT IN

1 2

3 4 5 6

7. Mixed 1/4 user distributors wiring

Code=32, DIP - 6=on

1 2 3 4 5

Code=31, DIP - 6=on

CALL

UNLO CK

TALK/M ON

INUSE

1 2 3 4 5

Code=30, DIP - 6=off

CALL

UNLOCK

TALK/MON

IN-USE

1 2 3 4 5

Code=4, DIP - 6=on

CALL

UNLO CK

TALK/M ON

INUSE

1 2 3 4 5

Code=3, DIP - 6=on

CALL

UNLOCK

TALK/MON

IN-USE

1 2 3 4 5

CALL

UNLOCK

TALK/MON

IN-USE

Code=2, DIP - 6=on Code=1, DIP - 6=on

DPS PS5

85~260AC

ID=00



Section4 - Setup and Debug

System Operations

Busy State Management

Calls and busy state are managed according to the programmed system times

• Pick-up waiting time: this is the duration from when a call is made from a Door Station to when the called Monitor is picked up; the system will cut off the call after this period of time.(the default setting is 30 seconds)

• Maximum talking time: this is the duration time that the indoor user can talk to the out door visitor. After this period the conversation will be cut off automatically by the system to free the line.(the default setting is 90 seconds)

• Maximum intercom time: this is the duration time that the indoor user can talk to the other indoor user when having a intercom conversation. After this period the conversation will be cut off automatically by the system to free the line.(the default setting is 30 seconds)

• Maximum monitoring time: this is the duration time that the indoor user can monitor (surveillance) via the Door Station or CCTV camera, when press the Monitor button on the Monitor.(the default setting is 30 seconds)

• Busy time: this indicates the period when a door unit can not place calls because a previous call or conversation is in progress.(maximun busy time = pick-up waiting time + maximum talking time)

The system works as follows when a Door Station call is made

• A call from any Door Station switches the entire system to pick-up waiting time mode (30 seconds). Busy state is prolonged (maximum talking time). The system returns to standby mode at the end of the conversation or after the timeout.

• An intercom call switches the Door Station(s) to busy mode for the pick-up time(30 seconds). When the called user picks up, busy state is prolonged for other 60 seconds (maximum intercom time). The Door Station(s) return to standby mode at the end of the conversation or after the timeout.

• It can be interruptedby the Door Station call when the Monitor is in intercom pick-up waiting time or in intercom conversations

• A intercom call or a monitor(surveillance) operation will not affect the system busy state. Intercom call will be ignored by the system when a Door Station call is calling or a Door Station talking is in process.

• The door bell call button call will not affect the rest of the system, but will interrupt the called Monitor if the Monitor is in monitoring(surveillance) or in intercom talking.

• Door Station call has the highest priority, monitor(surveillance) operation comes next, and the intercom operation has the lowest priority.

When door statin call or Door Station conversation is in process, the rest of the Monitors in the system will be turn into busy state, the busy LED on the Monitor will turn into red, and the screen of the Monitor can not be opened, have to wait untill the call or conversation is over.

Note that all the timings mentioned here can be change by the XL CONFIG software, which is included in the product. See theXL CONFIG software in section 5.

DPC-System-Technical

Door Station Function

1. Call Forwarding:

Every call button on the Door Station has a buttonID,whichisassociatedwith a Monitor ID(Monitor address or code). When a call button is pressed on a Door Station:

• Door Station free: the Door Station will output the call forwarding tone (a long beep(Di~) in every 3 seconds) and the nameplate light will blink. The Door Station will output an end of conversation tone at the end of the communication.

• Door Station busy: the Door Station will output a warning tone (4 short beeps). Press the call button again when busy mode ends.

2. Electronic Lock Management

There are two ways for the electronic lock management:

• Directly connect to the Door Station(connect to the GND and COM terminal), the Door Station supply power to the lock. In this case, the lock must be rated less than 12Vdc, 300mA.

• Use separated power supply for the electronic lock, only use the relay contact to control the lock. In this case, wide range of lock can be used in the system.All lock less then 48Vdc, 1.5Acan be supported.

The lock will be controlled in two ways:

• When a door open command is received from the Monitor, the lock is activated.

• When the exit door open button is pressed, the lock is activated.

3. CameraAuto-Switching

When multi Door Stations are installed in the system, the Monitor can surveillance the outside via Door Station or CCTV camera, and the video will automatically switch from the first Door Station to the last Door Station. Note that the duration for each Door Station should be set by theXL CONFIG software to enable theAuto Switching function .

• The surveillance time can be set by the computer uing the XL CONFIG software.

• Maximum 6 cameras can be supported.

• ADCU part is needed to connect to the CCTV cameras.

07 15 13 14 11 12 01 02

07 08 23 31 22 21 01 02

System Setup

What’s User Code

In 2-wire DPC, each Monitor installed in system must be programmed with a callingaddress or calling number, which is User Code.

For Monitor, User Code is defined by 1~5 bits DIP switchers on the connection board, according the User Code rules. For example, if you want to program the Monitor’s UserCode to be “03”, the Monitor’s 1~5 bit DIP switcher¬s should be set as: ON, ON, OFF, OFF, OFF(please refer to User Code table at section2-Monitor).

For Door Station, each Call Button on panel is assigned to a specified User Code, and press this button will call related Monitor. For example, press the call button labeled as “03”, system will launch a call to the Monitor which programmed with “03” User Code.

Note

that the Bit-4 of the DIP switches on the Door Station should be set to OFF

for Double line button Door Station, set to ON for Single line button Door Station. The User Code array on panels has been pre-defined as below, that’s the default mapping as follow:

Bit-4=off

Bit-4=on

01 05

1 2 345 6

DPC-D211E-8S DPC-D211E-24S

1 2 345 6

DPC-D211-4S

DPC-D211E-12S DPC-D211E-12S

However, the User Code mapping of Call Buttons can be changed, so as to meet the need of complex required installations. To program the Door Station User Code mapping, you have to use XL-CONFIG software to program each Door Station, by editing User Code, and download. Please see related contest for reference.

For example, when Call button of Guard Center and Cancel button are needed, User Code mapping may be:

In another installation example, 2 Door Stations are installed and need to be setup as below:

07 06 05 04 03 02

C G

Button C is defined for Cancel operation

Button G is defined

for calling Guard Unit operation

DPC-D211E-8S DPC-D211E-8S

DPC-D211-8D

1st door station 2nd door station

DPC-System-Technical

Slave Addr

Set -- 0

Guard

UnitSet -- 0

Date

and

Time

set...

Other

settings... Informations... Exit

What's SlaveAddress

2-wire DPC is capable of connecting up to 4 Monitors in one apartment, which means they will have the same User Code, and will be called simultaneously. In this condition, the Monitors should be programmed as below:

• 1.All the Monitors of same apartment must be programmed with the same User Code on the DIPswitches.

• 2.There is only one masterMonitorintheoneaparment,andtheSlaveAddress of the master Monitor is set to 0. Each Slave Monitor should be set from 1~3.

• By default, Monitor’s SlaveAddress is pre-set to 0(master Monitor).

• When Door Station calls, only the master Monitor will turn on the screen, the slave Monitor will only ring.

Master Monitor Slave Monitor 1 Slave Monitor 2 Slave Monitor

Slave

Address

Slave

Address

Slave

Address

Slave

Address

Please note, when called by Door Station,all Monitors will ring, however, only the Monitor which Sub User Code was programmed to 0 will turn on the screen.

Programming Slave User Code is by meansof Monitor Menu, in the Main

- -

> Setup

- -

>Advance Set page(a password

will be required before enter the setting, the password is:

2008

), operate as below:

• The Slave Addr Set item is for the master and slave user code setting, default is set to 0 for master user code. It can be change to 1, 2 or 3.

• The Guard Unit Set item is for Guard Unit Monitor setting, the default it set to 0, if set to 1, this Monitor is become a Guard Unit Monitor.

Ho m eIntelligent Syste

Online search

Online search function is designed for the purpose of getting a quick view of the Monitors installing situations, or to check if each of them works or not. This is veryuseful for installation maintain. There are 3 differentways to use the Online Search function, manually search, use the ID tab and use theXL CONFIG software.

When the Online search is actting, the Door Station will search every Monitor with the User Code from 1 to 32. If the Monitor is one line(work normally), the LED light of that button will light up, and one 'Di~' sound hit will be heared; if the Monitor is off line(disconnected or mulfunctioning), the LED light of that button will not light up, and a 'Di,Di,Di' sound hit will be heared. After 32 Monitors all be searched, the Monitor will quit out automatically, or press PB button to abort the seaching.

1. Manual search

To execute searching, just press PB button(or hold it for 3 seconds) on Door Station Connection Board, the Door Station will start searching, and the resultis shownby lighting the related Name Label backlight with soundtips.After 5 seconds, Door Station returns to normal.

• Press the PBbutton, will search the Monitors in the right Call Buttons column.

• Press the PB button and hold for 3 seconds, will search the Monitors in the left Call Buttons column.

07 08 05 06 03 04

31 32 29 30 27 28 25 26 23 24 21 22 19 20 17 18 15 16 13 14 11 12

07 08 05 06 03 04

31 32 29 30 27 28 25 26 23 24 21 22 19 20 17 18 15 16 13 14 11 12

01 02 09 10 01 02 09 10

PB button for 3 seconds

Online searchrange

PB button

Online searchrange

For Example, if 01, 03, 04,11, 12, 13, 28 Monitors are installed and work correctly, the result will be:

07 08 05 06

03 04

31 32 29 30 27 28 25 26 23 24 21 22 19 20 17 18 15 16

13 14 11 12

07 08 05 06

03 04

31 32 29 30

27 28

25 26 23 24 21 22 19 20 17 18 15 16 13 14

11 12

01 02 09 10 01 02 09 10

press PB button and hold for 3

seconds

press PB button

once

DPC-System-Technical

2. Use ID tag

The Door Station will be equiped with a Online search Card with a card number of 16666666, which is designed for the online search only.

Show the Online search card on the card window one time within 3 seconds, the Door Station will start to search the Right column Monitors; show the Online search card on the card window tiwce within 3 seconds, the Door Station will start to search the Left colume Monitors

16666666

3. Use XL-CONFIG Software

By means of a PC and software, it is easy to run online check, voltage measuring,and to check device properties. Additionally, the debug log can be saved for future reference. Please refer to section 5XL CONFIG software.

Simulating Call

The simulating call function is designed for the purpose of testing the Monitor's working state, which enable the installer to check a certain Monitor working state by only one person.

Press and hole the Call Button for 2 seconds on anyMonitor, the Door Station will call the Monitor automatically,then the installer can answer the call and check if system work properly(such as video, audio etc).

1 2 3 4 5 6

485 SET

Section5 - XL CONFIG Software

Introduction

XL-CONFIG software is a powerful configuration and debug tool to setup the 2-wire system. As simplified software tools, XL-CONFIG allows installers to check and programDoor Stations rapidly, which is especially useful in complex installation.

XL-CONFIG allows you to view device properties, modify parameters, re-locate Call Button and establish Name List in a PC and then download to the Door Station. Furthermore, you can use XL-CONFIG as a assistance in field debug and maintains, by means of printing ProgrammingTable, online search and diagnose tools.

XL-CONFIG contains a project management utility, which helps installers manage project and device information. For detail informations, please refer to the software document in the CD disk which included in the product.

CALL

UNLOCK

TALK/MON

IN-USE

010100101

NAME

001100101

NAME

Hardware connection

Door Station

+12V

T/R -

LK - (GND) LK+(COM) N.O.

EB+ EB -

T/R+

USB Convertor

Computer

1 2 3

BUS

DPC-System-Technical

Interface Preview

1. Main Menu (Infomation Menu)

2. Paremeters Menu

The Information tab shows the product Model, Hardware Version,

Software Version, Serial No. , Access Control, Access Card Number information.

On the Installer's Information tab, user can input the Project Name and

Block Name for this Door Station.

Note: Series No. is a unique number programmed in factory and used for tracking. Refer to the software document in the disk for detail infomations.

The Parameter Menu is for the timing settings for the system. it includes the following settings:

• Monitor Timing: For the maximun monitoring time setting.

• Camera Swithing Timing: The surveillance time for each Door Station or CCTV camera.

• Wait Timing: To set call wait and ring time, if Monitor don’t answer a call within this time, calling will be canceled.

• TalkTiming: Set limitation time of talking.

• Unlock Timing: To set the time that how long the door keeps open

when lock is released.

• Mon Speak: To enable the talking with the Door Station when the Monitor is under monitoring state.

• Mon Unlock: To enable the door lock opening operation when the Monitor is under monitoring state.

• Unlock Relay: To select the unlock relay mode for different lock types.

3. Namelist Setup

4. Access Control

This menu is for the namelist input and download operations. All user namelist can be input and download to the Door Station and the Door Station will send the namelist to every Monitor in the system.

The Access Control tab included two sub tabs, Device Operation and

File Operation.

The Device Operation is used to add/delete user cards or master cards. And all the card rigister information can be save as a backup file, so that the information can be easy recover should any problem happen to the card reader or any wrong operation to the Door Station.

The File Operation allow the installer to add ID cards by the software without any operation on the Door Station by input the card umbers and the corresponding User Codes.

DPC-System-Technical

5. Debug Tool

The debug tool is very useful when trouble shoot or maintenant the system:

• User Code Range: To change the User Code start and end address, only set valid range will save more time.

• Online Check Button: Use this button to start Online searching, and the result will be showed in list window.(Online search function is designed for the purpose of getting a quick view of the Monitors installing situations, or to check if each of them works or not. This is very useful for installation maintain).

• Diagnose Button: Use this button

to start Diagnose operation, and the result will be showed in list window.

• Diagnose operation will check the Monitor’s working voltage and standby voltage, video signal presentence, and data communication.(By means of this tool, if a Monitor passes the test, generally this Monitor should works well).

• Print Button: To print the debug result window information, for installation delivery documentation or memo.

• Export Button: To export the results for future usage.

6. Trace Tool

TRACE tool will display all data communication information presented on 2-wire BUS, which can be a high

end tool used by expertise to check the system stability, or locate the problem more easily in a complex installation. Please note, it is not suitable for normal installers, as the data streams are complex. However, installers can send back the trace log, thus the engineers can analyze and help.

DPC User Code Programming Table page1/2

User code Bit state Room Name Lable Remark

1 2 3 4 5

DPC-System-Technical

DPC User Code Programming Table page1/2

User code Bit state Room Name Lable Remark

1 2 3 4 5

32(00)

1 2 3 4 5

XtendLan D-2Wire User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual