Using a power
ADS-2400 IP DSLAM
QQuuiicckk IInnssttaallllaattiioonn GGuuiidde
e
Thank you for purchasing the ADS-2400 ADSL2/2+ IP DSLAM. Following
the Quick Installation Guide, your can quickly deploy this device in several
minutes. For getting advanced information, refer to the user manual.
Check Your Package Contents
I
• ADSL2/2+ IP DSLAM
• CD-ROM
•Ethernet Cable (CAT5 UTP Straight-Through)
• AC Power Cord
• RS-232 cable
supply with a
different voltage rating
will damage and void
the warranty for this
product.
Setup the IP DSLAM
The DSLAM can be installed in a standard 19-inch rack, by using the
mounting brackets provided. Mount the shelf on the rack using the
large screws provided. The procedure to connect and wire the system
is as follows.
Rear Panel Connection
The following figure shows the rear panel connection of DSLAM
Step 1: Ground the DSLAM by connecting a grounded wire
Step 2: Connect the “Line” connector, a 50-pin centronic connector, of
DSLAM to CPE. Each connector supports 24 ports of
ADSL/ADSL2/2+ for Data path.
Step 3: Connect the “Phone” connector, a 50-pin centronic connector,
of IPAM-4800/4824 to Exchange/PBX.
Note: (1) Patch panel and Telco cables are optional to standard
package.
(2) The 1st port of each connector comes to pair of pin #25
and pin #50, instead of pair of pin #1 and pin #26
Step 4: Hook power cord and apply the power.
Connect to another IPAM
-
4800
Front Panel Connection
EMS Configuration
This section shows how to prepare the system to perform basic
communication functions through Element Management System
(EMS). Perform initial configuration procedures as follows:
Management
1. Click the EMS button on the screen of autorun to install EMS
2. Before you start to connect to EMS, it is necessary that your
Note: Default IP address of Management port is 192.168.200.111
3. To enable SNMP for EMS access, one needs to issue
a. “$create snmp comm community public rw”
b. “$create snmp host ip 192.168.200. xxx community public”,
c. “$create snmp traphost ip 192.168.200.xxx community public
into your PC with Windows NT, XP or 2000.
PC’s IP and DSLAM`s IP are in the same group.
commands below to DSLAM by Telnet to management port or
connecting to console port (9600, N, 8 ,1) and then log in with
default username and password of “admin”.
where 192.168.200.xxx is the IP of your PC.
version v1”, where 192.168.200.xxx is the IP of your PC.
4. Launch the EMS and then log in with the “Admin” for both
user name and password. Click on to enter the EMS
system.
5. Add the IP address of DSLAM into the Agent manager.
6. Then the IP address and alias name will be displayed on
the Agent Desktop. Double click the DSLAM’s IP address
in the Agent desktop.
7. After that, you could enter the main menu of EMS for your
configuration.
Default Setting
Click on the Default Setting from the DSLAM main menu. The
Default Setting window will be displayed.
Configure the System
Note: the
Click on the System Information from the DSLAM main menu in
which some parameters related to the system are available for
configuration. The DSLAM System Information window will appear
as follows:
Configure DSL Profile
Click on the DSL from the Configuration menu.
The DSLAM DSL menu tree and related windows
will appear as follows:
value as CPE.
Item Description
Line Profile
Configuration
Alarm Profile
Configuration
Port Configuration
To browse and create ADSL
line profiles.
To browse and create ADSL
alarm profiles.
To display, modify or delete
the status of the port. It
provides the configuration of
a port’s status.
“vpi” & “vci” in “port configuration” page has to be set as same
Line Profile Configuration window
Alarm Profile Configuration window
Port Configuration window
Advanced Setting
For more detailed information about complete configuration, please refer
to the User’s Manual on the support CD
MEMO
Loading...