X-Taste ARES User Manual
1
ARES
User Manual V1.10
2
The ARES is designed for professional vapers. To ensure safety and
proper usage of the device please read the instruction carefully.
It is prohibited to open body of the device otherwise warranty will
be void.
Do not expose device to heat source for long period. It might
damage the battery.
Warning: Abnormal operation may damage the device!
This product is strictly for above 18 years only.
Open Box (Basic configuration):
1. 1x ARES device
2. 1 x USB cable (support up to 2A)
3. 1 x user manual
3
1. Specification and features
Model: ARES
Dimension: Height x Width x Length (93mmx48mmx32mm)
Weight: 165g
Body Material: Zinc Alloy + Aluminium Alloy
Atomizers Connector: Stainless Steel 510 Connection, Nickel Plated Brass Contact
Display: 1.3 OLED
Support both dual 18650 or dual 20700 Li-On Battery
Atomizers
o Output power range: 5W ~ 220W
o
Maximum 40A continuous current.
o
Output voltage range: 0.5V ~ 15.5V (Buck-Boost DC-DC converter)
Power consumption (Without fire): 0.4W
Very low standby current: 39.5uA (Able to standby 3.9 years for fully charge battery)
Coil resistance
o
Measurement range 0.04Ohm ~ 10Ohm
o Resolution: 1m Ohm (based on 0.1ohm measurement)
Power control mode
o Recommended resistance range: 0.08Ohm~3Ohm
o
Coil over heat protection. Refer to coil material table for detail.
Temperature control mode
o
Recommended resistance range: 0.08Ohm~2Ohm
o Repeatability: 1 degree Celsius / 1.8 Fahrenheit
o Support Ni-200, Ti 01/02, SS316L, NiFe30, NiFe70. Refer to coil material table for
detail.
o Temperature adjustment range can be change through “X-Taste Advance”.
o
Dry coil protection.
Power control / Temperature control mode
Battery Management
o Support maximum up to 2A USB charging current.
o
Support cell by cell monitoring
o
Support cell balancing: 99.5%
4
Safety feature
o
Dry coil protection (only applicable for temperature control mode)
o Coil overheat protection
Support Ni200, Ti01/02, SS316L, NiFe30, NiFe70, Nichrome N60. Refer to coil
material table for detail.
Protection temperature can be change through “X-Taste Advance”.
o Real-time battery temperature monitoring. Auto shutdown device if temperature
too high or too low.
o
Real-time on-board temperature monitoring. Auto shutdown device if temperature
too high.
o Battery health condition checking feature. Able to give alert if battery not in good
condition.
o Coil over voltage protection.
o Coil over current protection.
o Coil short/open circuit protection.
o Weak battery protection.
o Battery over charge protection.
o
Battery over load protection.
o
10 seconds maximum fire duration protection.
Support firmware upgrading through USB port.
Screen lock features.
Coil resistance measurement features.
Real-time display data during fire on
o Battery voltage, capacity
o
Coil resistance (power mode)
o Sensing coil temperature (temperature mode)
o Coil voltage
Auto power off features, 6 minutes.
o Can be modifying through “X-Taste Advance”.
5 individual preset configurations.
Continuous short press “Fire ON” button 3 times to power on devices.
Smart auto lock coil resistance.
Using TCR or temperature coefficient based on type of coil material for more precise
temperature control and coil overheats protection.
X-Taste Advance software allow user to modify setting and operation of the device.
5
Coil Material Table:
Coil Material
Overheat protection
Temperature Control
Range
Temperature Control
Resolution
Ni200
331 Degree C
628 Fahrenheit
100~316 Degree C
212~600 Fahrenheit
1 Degree C
1 Fahrenheit
Ti01/Ti02
331 Degree C
628 Fahrenheit
100~316 Degree C
212~600 Fahrenheit
1 Degree C
1 Fahrenheit
NiFe30 (Stealth Vape)
331 Degree C
628 Fahrenheit
100~316 Degree C
212~600 Fahrenheit
1 Degree C
1 Fahrenheit
NiFe70
331 Degree C
628 Fahrenheit
100~316 Degree C
212~600 Fahrenheit
1 Degree C
1 Fahrenheit
SSL316L
331 Degree C
628 Fahrenheit
100~316 Degree C
212~600 Fahrenheit
1 Degree C
1 Fahrenheit
Nichrome N60
331 Degree C
628 Fahrenheit
NA
NA
Kanthal A1
NANANA
Active Region Table:
6
Structure Diagram
Fire Button
“Left” Button
“Right” Button
7
2. Operation (Power Up Device)
- Short press “Fire” button 3 times to power up devices.
- This design is to avoid “fire” being trigger accidently.
- Device auto enter power off mode after 6 minutes of idling.
3. Operation (Coil Resistance measurement)
- Press “Left” + “Right” for coil resistance measurement.
Firmware version
8
4. Operation (Power mode)
- Long press “Left” button to trigger adjust target power. Press “Right” to increase and
“Left” to decrease power. Press “fire” button to confirm the power setting.
- Short press “Right” to switch different fire mode (soft, standard, powerful)
- Long press “Right” to enter main menu.
- Short press “Left” to switch different preset memory setting.
- Press “Left” + “Right” for coil resistance measurement.
- Press “fire” button to start fire.
- Under “MENU/Control” select “Wattage” to enter power mode.
- Fire mode “Powerful” giving 10% more power than “Standard “mode configuration.
- Fire mode “Soft” giving 10% less power than “Standard” mode configuration.
Target power
Preset memory
Coil material
Fire mode: Soft, Standard, Powerful
Elapsed time
Measured coil voltage, V
Measured coil
resistance, ohm
Battery 1,2
capacity and
voltage.
Loading...