Xtant Technologies P-500 Owners manual

PARAMETRIC EQUALIZATION

The P500 is a 5-band parametric equalizer. Its design
allows the user to vary center frequency, select a “Q” of 1­10, and select up to 18 dB of boost or cut.

Center frequencies range from 20 Hz to 20 KHz. The on­board frequency jumper divides the frequency range into three
bands: 20 Hz to 200 Hz, 200 Hz to 2 KHz, and 2 KHz to 20 KHz.
Simply place the jumper in one of the three positions which cor­responds with the frequency to be adjusted. The specific fre­quency is then selected via the “frequency” potentiometer

“Q” determines the range of frequencies affected on either
side of the center frequency. “Q” is equal to the center fre-
quency divided by the bandwidth. As “Q” goes up, bandwidth
decreases. The P500’s “Q” adjustment ranges from a narrow
bandwidth of 10 to a very broad bandwidth of 1.

Boost / Cut on the P500 is +/–18 dB. The rotary poten­tiometer provides continuously variable adjustment.

P500 TUNING SEQUENCE

The P500 is designed to be “set-up” or “tuned” with the aid
of a Real Time Spectrum Analyzer measuring a pink noise sig-
nal generated by the mobile audio system. The analyzer pro­vides visual feedback when following the steps listed below.

RTA the system and determine points of adjustment. Turn
the system off and place each of the frequency range jumpers
into their corresponding “frequency range” positions.

•••••••••

installer’s reference

xtant technologies

THI S DOCUMENT HA S BEEN CRAFTED TO MAKE INSTALLA-

TION, SYSTEM DESIGN A N D TROUBLE- SHOOTING, A QUICK
A ND EASY PROCESS

. THE CHARTS PROVIDED, OFFER A SIM-

PL E METHOD O F DOCUMENTATION.

IT IS IMPORTANT THAT YOU RETAIN THIS LOG
FOR YOUR RECORDS. O

N PAGE 8 OF THE OWNER’S

MANUAL, YOU WILL FIND THE OWNER’S REFERENCE LOG.
O

NCE YOU HAVE NOTATED THE FINAL SETTINGS FOR THIS

P500, TRANSFER THOSE SETTINGS TO TH E OWNER’S
REFERENCE LOG. IN THE FUTURE, A N Y SYSTEM EXPANSION

AND

/ OR PROBLEMS M AY BE REFERENCED TO THIS LOG.

INSTALLATION SEQUENCE

REMOVE P500 COVER:

Loosen allen head screws and lift-off cover. Do not remove
protective covering on stainless steel lid until installa­tion is complete.

TEMPORARILY MOUNT P500:

The P500 is designed to be anchored through the four (4)
holes located on the circuit board/base assembly.

MARK WIRES FOR TERMINA TION AND REMOVE P500:

Determine wire lengths for Power, Ground & Remote and
mark for cutting/termination. Remove P500 before cut­ting and terminating all wires. CAUTION: stripping
wires over the circuit board may cause product failure.

INPUT SENSITIVITY:

Make initial adjustment to input gain at your work bench.
Refer to the section “Input Sensitivity” on the reverse
side.

BALANCED LINE:

Make initial adjustment at your work bench. Refer to the
section “Balanced Line” on the reverse side

MOUNT THE P500 AND MAKE ALL CONNECTIONS:

Re-install the P500 and make all wire connections. i.e.
Power, Ground, Remote and RCA input/outputs.

DOUBLE CHECK ALL CONNECTIONS! TURN ON P500:

Check red LED, it should be on.

MAKE ALL EQUALIZATION ADJUSTMENTS:

Refer to “P500 Tuning Sequence” in this “Reference”

ADJUST NOISE GATE THRESHOLD (IF USED):

Refer to “Activating the Noise Gate” on the reverse side

AFTER FINE TUNING THE SYSTEM:

Remove protective covering from P500 and clean. Attach
cover to base.

•••••••••

INSTALLER’ S REFERENCE LOG

DA T E INSTALLED:
OWNER’S NAME: PHONE:
A DDRESS:
CITY/STATE: ZIP:
VEHICLE: YEAR:
XTANT P500 SERIAL#

MODES OF OPERATION: (CIRCLE SETTING)

INPUT MODE: 4 CHANNEL 2 CHANNEL
BALANCED LINE: ENABLE DISABLE
NOISE GATE: O N DEFEAT

P500 ADJUSTMENTS (DRAW POSITION OF CONTROL & CIRCLE FREQ. RANGE SELECTED)

system components

SOURCE SERIAL #
PROCESSOR( S) SERIAL #

SERIAL #

AMPLIFIER( S) SERIAL #

SERIAL #
SERIAL #

xtant technologies •••••••••

7676 SOUTH 46TH STREET PHOENIX, ARIZONA 85040 USA

••••••••602 431 8686

CENTER FREQUENCY

RANGE OF BOOST

/CUT

LOW “Q”: A WIDER RANGE OF FRE-
QUENCIES (ON EITHER SIDE OF THE
CENTER FREQUENCY

) ARE AFFECT-

ED BY EQUALIZATION.

HIGH “Q”: A NARROW RANGE OF
FREQUENCIES

(ON EITHER SIDE OF

THE CENTER FREQUENCY

) ARE

AFFECTED BY EQUALIZATION

.

Perform the following steps per band:

With the system playing pink noise, turn on the
RTA and adjust pink noise SPL to 85 – 90 dB.

Turn the boost/cut control to +18 dB (full clockwise
rotation). This will show the present center frequen­cy and “Q” settings on the analyzer.

Rotate frequency control to the frequency you wish to
adjust.

Adjust “Q” setting to match the width of the dip or
peak you are addressing.

Finally, adjust the gain control to achieve the desired
response curve.

Freq. Range

20 – 200 Hz
200 – 2 KHz
2K – 20 KHz

Freq. Range

20 – 200 Hz
200 – 2 KHz
2K – 20 KHz

Freq. Range

20 – 200 Hz
200 – 2 KHz
2K – 20 KHz

Freq. Range

20 – 200 Hz
200 – 2 KHz
2K – 20 KHz

Freq. Range

20 – 200 Hz
200 – 2 KHz
2K – 20 KHz

front “a”

front “b” front “c” rear “a” rear “b”

+/– 18 dB

Q ADJUST

FREQ.

+/– 18 dB

Q ADJUST

FREQ.

+/– 18 dB

Q ADJUST

FREQ.

+/– 18 dB

Q ADJUST

FREQ.

+/– 18 dB

Q ADJUST

FREQ.

XTANT TECHNOLOGIES 7676 SOUTH 46TH STREET PHOENIX, ARIZONA 85040 PHONE: [phone] FAX 60

INSTALLER’S
REFERENCE

..............

XT ANT P500

..............

SETTING THE E

TION OF THE POTENTIO
ROTATION DECREASES
THE USE OF AN RTA, P
ENCE – KEEP IN MIND
ATED VALUES PICTUR
STRONGLY SUGGESTS

2

1

-18dB

3

1.1

-10dB -6dB

1.6

“Q”

Center FREQUENC

FREQUENCY VALUE IS A
1000 DEPENDING UPON
= X 10, FREQ JUMPER 2

Full counter clockwi
clockwise rotation p

FULL COUNTER CLOCKWIS

ROTATION PRODUCES A

“Q

2CH / 4CH INPUT MODE JUMPER:THE POSI-

TION OF THE INPUT MODE JUMPER DETERMINES THE OPER-
ATIONALMODE OF THE EQUALIZER. IN THE 2CHMODE, ONLY
THE FRONT INPUTS AND REAROUTPUTS ARE USED AND ALL

5 BANDS OF EQUALIZATION ARE AVAILABLE FOR USE. IN

THE 4CH MODE, BOTH THE FRONT AND REAR INPUTS/OUT-
PUTS ARE OPERA TIONAL AND THE 3 EQ BANDS LABELED

“FRONT A, B &C” ARE TIED TO THE FRONT INPUTS/OUT-

PUTS AND THE 2 EQ BANDS LABELED “R EAR A & B”
ARE TIED TO THE REAR INPUTS/OUTPUTS.

INPUT SENSITIVITY: FRONT AND REAR INPUT

SENSITIVITY IS DESIGNED T O BE SET INDEPENDENTLY. TO
ADJUST INPUT GAIN, PLACE THE JUMPER IN THE POSITION
WHICH ALLOWS MAXIMUM GAIN BEFORE CLIPPING (DIS-
TORTING). IN THE 2 CHANNEL MODE, ONLY THE FRONT
INPUTS (MAY) REQUIRE ADJUSTMENT.

PLEASE REFER T O THE CHART BELOW WHEN SETTING

INPUT SENSITIVITY. THESE SETTINGS ARE DESIGNED TO BE
A STARTING POINT OR REFERENCE. IF MORE INPUT GAIN IS
DESIRED, MOVE THE JUMPER TO A HIGHER “+” SETTING.

TO ACHIEVE LOWER GAIN, MOVE THE JUMPER TO ONE OF

THE “–” POSITIONS. THE P500 IS SHIPPED WITH THE

F/R INPUT SENSITIVITY SET AT +10 dB.

+20 dB = 100 – 300 mV

+10 dB = 300mV – 1V

0 dB = 1V – 3V

–10 dB = 3V – 8V

–20 dB = 10V – 17V

BALANCED LINE: XTANT’S BALANCED LINE TECH-
NOLOGY MAY BE USED TO ELIMINATE INDUCED AND/OR
GROUND-LOOP RELATED NOISE, RECEIVE SIGNAL FROM A
BALANCED SOURCE, INTERFACEWITH A HIGH LEVEL SIGNAL

(SPEAKER OUTPUTS) AND/OR BE USED AS AN OEM

SOURCE UNIT INTERFACE.

EACH SET OF INPUTS (FRONT/REAR) OF THE P500

FEATURE BALANCED LINE CIRCUITR Y. TO ACTIVATE THIS CIR-
CUITRY, SIMPLY MOVE THE BALANCED LINE JUMPER TO THE

“ENGAGE” POSITION.

TO USE BALANCED LINE IN THE 2 CHANNEL MODE,

ONL Y “ENGAGE” THE FRONT INPUTS.

THE OUTPUTS OF THE P500 ARE NOT BALANCED.

GENERALL Y, THE BENEFITS DERIVED FROM BALANCED
INPUTS ARE AVAILABLE AT THE OUTPUTS.

FREQUENCY RANGE JUMPER: EACH BAND OF
EQUALIZA TION HAS A FREQUENCY RANGE JUMPER WHICH
DETERMINES THE RANGE OF CENTER FREQUENCIES AVAIL-
ABLE FOR ADJUSTMENT. THREE RANGES ARE AVAILABLE:

20 TO 200 HZ, 200 TO 2,000 HZ AND 2,000 TO
20,000 HZ.

TO SELECT A RANGE, SIMPLY PLACE THE JUMPER IN

THE CORRESPONDING POSITION AS DETAILED IN THE ILLUS-
TRATION. ONCE IN PLACE, THE FREQUENCY ADJUSTMENT
POTENTIOMETER ALLOWS YOU TO SELECT ANY FREQUENCY
WITHIN THAT RANGE.

BOOST/CUT

ACTIVATING T

GATE IS DESIGNED TO
TRACKS ON CD’S. ITIS
LOCATED BEHIND THE
MOVE THE SWITCH TO T
THE SWITCH IN THE DIS

NOISE GATE

INCREASES SENSITIVIT
TERCLOCKWISE ROTATIO
MORE INPUT SIGNAL. N
CLOSE AT A SLOWER R

NOISE GATE TH

OPEN AND CLOSE VIA T
IS PROVIDED TO INDICA

(PASSING SIGNAL) THE

PASSING SIGNAL), THE

SELECT A CD AND

IMUM LISTENING LEVE
PLAYING, TURN THE T
GATE “CLOSES”. ATT
GROUND HISS”. IF THE
LEVEL MUSIC INFORMA
PROPER THRESHOLD S

The P500 can be

powered by a Radio

Shack

®

AC Adapter

# 273 1653B

(12VDC/1000MA)

BYPA SS JUMPERS: THESE JUMPERS
ARE USED TO COMPARE SIGNAL BEFORE
AN AFTER EQUALIZA TION. IN 4CH MODE,
THE FR ONT AND REAR EQ BANDS MA Y BE
BYP ASSED INDEPENDENTLY. IN THE 2CH
MODE, ONLY THE JUMPER LABELED
REAR/2CH IS USED TO BYPASS.

FREQ

“Q” “Q”“Q”“Q” “Q”

BOOST/CUT BOOST/CUTBOOST/CUTBOOST/CUTBOOST/CUT

INPUT SENSITIVITY ADJUSTMENT

FRONT INPUT REAR INPUT

+20 dB
+10 dB

0 dB
–10 dB
–20 dB

DISABLE

ENABLE

FRONT INPUT

BALANCED LINE INPUTS

REAR INPUT

2 / 4 CH INPUT MODE

4 CHANNEL

THRESHOLD ADJUST

DISABLE

ENABLE

FRONT OUTPUT

NOISE GATE

FRONT

2 CHANNEL

REAR OUTPUT

RIGHT RIGHT

LEFTLEFTLEFTLEFT RIGHT RIGHT

2 CH INPUT 2 CH OUTPUT

Front “C”Front “B”Front “A ”

REAR

/2 CH

BYPASS

EQ

THRESHOLD LED INDICATOR

ENABLE
DISABLE

BYPASS

POWER ON LED

EQ

CHASSIS

REMOTE

Rear “A ” Rear “B”

FREQFREQFREQ FREQ

FREQUENCY RANGE
JUMPER POSITIONS

2KTO20 KHZ
200 TO 2 KHZ

20 TO 200 HZ

1 AMP FUSE

+12V

AUX +12V IN