Xtant Technologies 603-X Owners manual

INPUT SENSITIVITY ADJUSTMENT
Each set of inputs (front/rear) on the 603x are adjustable in 10 dB steps from -20 dB to + 20 dB The five (5) input gain settings allow the 603x to accept input voltages from 100 mV to 8 V. The front and rear input sensitivity is adjusted independently by installing a jumper across the associated input voltage/pin location. Refer to the illustra­tion on the reverse side of this document prior to setting the input sensitivity.
CROSSOVER MODES OF OPERATION
The 603x is equipped with independent FRONT and REAR crossovers. Each crossover is controlled by two (2) crossover mode jumpers labeled AMP & LINE XOVR. The header jumper labeled AMP XOVR control the crossover function as it applies to the 603x’s Front (stereo) and Rear (mono) amplifier. The modes of operation are: Position 1 = Bypass (Full Range), Position 2 = High Pass, and Position 3 = Low Pass. (See illustration)
The two (2) header jumpers labeled LINE XOVR control the crossover function as it applies to the 603x’s FRONT and REAR RCA Line Outputs. The modes of operation are: Position 1 = Bypass (Full Range), Position 2 = High Pass, and Position 3 = Low Pass. (See illustration )
The High and Low Pass frequencies are determined by the Frequency Modules (SIPs) installed in the four (4) SIP sockets pictured on the reverse side of this document.
CROSSOVER FREQUENCY MODULES
The following is a chart of the available Xtant frequency module SIPs. The frequency module SIP’s “ID Code” printed on the SIP and the associated frequency value is detailed below.
SIP Number Frequency
224 50 Hz 134 70 Hz 114 80 Hz 104 90 Hz 683 120 Hz 563 150 Hz 273 300 Hz 153 500 Hz 103 700 Hz 682 1 kHz 242 3 kHz 182 4 kHz 152 5 kHz
The 603x amplifier is shipped from the factory with 90 Hz High and Low Pass frequency modules (SIP) installed. To change frequency modules, simply remove each resistor SIP and replace it with the appropriate SIP value to achieve the desired frequency.
The Low and High Pass frequencies are independent. Any combination of the available frequency modules (SIPs) may be used (ie. 80 Hz Low Pass and 120 Hz High Pass).
••••••••••••••••
installer’s reference
xtant technologies
THIS DOCUMENT H A S BEEN CRAFTED T O MAKE INSTALLA-
TION, SYSTEM DESIGN A N D TROUBLE- SHOOTING, A QUICK A ND EASY PROCESS
. THE CHARTS PROVIDED, OFFER A SIM-
PL E METHOD O F DOCUMENTATION.
IT IS IMPORTANT THAT YOU RETAIN THIS LOG FOR YOUR RECORDS. O
N PAGE 12 O F THE OWNERS
MANUAL, YOU WILL FIND THE OWNERS REFERENCE LOG. O
NCE YOU HAVE NOTATED THE FINAL SETTINGS F OR THIS
603X, TRANSFER THOSE SETTINGS TO TH E OWNERS REFERENCE LOG. IN THE FUTURE, A N Y SYSTEM EXPANSION
AND
/ O R PROBLEMS M A Y B E REFERENCED T O THIS LOG.
INSTALLATION SEQUENCE
REMOVE AMPLIFIER COVER:
Loosen allen head screws and lift-off cover. Do not remove protective covering on stainless steel lid until installation is complete.
TEMPORARILY MOUNT AMPLIFIER:
The amplifier is designed to be anchored through the four (4) sleeved holes located on the circuit board/base assembly. (see illustration)
REMOVE AMPLIFIER AND MARK WIRES FOR TERMINATION:
Determine wire lengths and mark for cutting/termination. Remove amplifier base before cutting and terminating all wires.Caution: stripping wires over the
circuit board may cause product failure.
CROSSOVER SET-UP:
Adjust crossover mode jumpers at your work bench. Also, change crossover frequency SIP’s if desired.
INPUT SENSITIVITY:
Make initial adjustment to input gain at your work bench. The factory setting is +10 dB / 300mv -1V. To increase input gain, place jumper in the +20 dB posi­tion. To decrease input gain, place jumper in the 0 or
-10 dB position.
MOUNT THE AMPLIFIER AND MAKE ALL CONNECTIONS:
Re- install the amplifier base and make all wire con­nections. i.e. Speaker, Power, Remote, Ground, and RCAinput.
DOUBLE CHECK ALL CONNECTIONS! TURN ON AMPLIFIER.
Check red LED, it should be on.
ADJUST LEFT, RIGHT & MONO AMPLIFIER OUTPUT LEVELS. ADJUST NOISE GATE THRESHOLD (IF USED):
Turn noise gate on and adjust the threshold by turn­ing clockwise to increase sensitivity (gate will open with less input signal). The green LED will illuminate when the gate passes signal.
AFTER FINE TUNING THE SYSTEM:
Remove protective covering from amplifier and clean per the maintenance section on page 9 of the Owner’s Manual. Attach cover to base.
•••••••••
INSTALLERS REFERENCE LOG
DA TE INSTALLED: OWNERS NAME: PHONE: A DDRESS: CITY/STATE: ZIP: VEHICLE: YEAR: XTANT AMPLIFIER:MODEL SERIAL#
input sensitivity (CIRCLE SETTING)
FRONT INPUTS (2 CHANNELS) REAR INPUTS (MONO CHANNEL)
–20dB –10 dB 0d B +10dB +20 dB –20 dB –10 dB 0 d B +10 dB +20 dB
Front Crossover (2 CHANNELS) Rear crossover (MONO CHANNEL)
CIRCLE JUMPER SETTING: CIRCLE JUMPER SETTING:
Amplifier: Amplifier:
ALL HIGH LOW ALL HIGH LOW
rca outputs rca outputs
ALL HIGH LOW ALL HIGH LOW
frequency v alue (2 CHANNELS) frequency v alue ( MONO CHANNEL)
SIP HIGH PASS FREQUENCY SIP HIGH PASS FREQUENCY SIP L O W PASS FREQUENCY SIP LO W PASS FREQUENCY
output gain adjustment noise gate adjustment
SWITCH: O N OFF
threshold position
Accessory modules ( CIRCLE SETTING)(DRAW ARROW POSITION) pqm-1 ( FRONT) YES N O Balanced input
pqm-1 CHIP FREQUENCY FRONT REAR pqm-1 ( REAR) YES N O ENABLE D ISABLE ENABLE D ISABLE pqm-1 CHIP FREQUENCY
XTANT SELECT DEALER PHONE INSTALLATION SPECIALIST DATE I NSTALLED
xtant technologies •••••••••
7676 SOUTH 46TH STREET PHOENIX, ARIZONA 85040 USA
••••••••602 431.8686
RIGHTLEFT MONO
left gain Right gain mono gain
Front Module port
ENABLE
2 4
DEFEAT
disABLE
left right left right
Front
Input Gain
Front balanced line input
Front Module port
Front Inputs Rear
left right left right
left right left right
Front outputs Rear
rear
Input Gain
+20
+10
0
-10
-20
+20
+10
0
-10
-20
12
dB
24
dB
by hi lo
bnd lo hi by
rear balanced line input
Channel
Input
mode
line out
Amplifier x-over
slope select
lo pass hi pass
Front Module port rear Module port rear Module port
ENABLE
Left lo pass sip
Left hi pass sip
right lo pass sip
right hi pass sip
threshhold adjustment
noise gate
12
dB
24
dB
by hi lo
bnd lo hi by
line out
Amplifier x-over
red LED
Power On
yellow LED
over current
orange LED
over temp
fan
speed
service jumper
slope select
lo pass hi pass
off
remote chassis +12v
on
Left lo pass sip
Left hi pass sip
right lo pass sip
right hi pass sip
insert resistor
module here
front crossover Settings rear crossover Settings
front passive mono
+-+-+-+-+-
normal
slow
CROSSOVER
MODE JUMPERS
:
CROSSOVER
FREQUENCY
SELECTION
:
TO CHANGE THE FRE- QUENCY OF EITHER THE HIGH AND/OR LOW P ASS FIL TERS, REPLACE THE
90 HZ FREQUENCY
MODULE (SIP) INSTALLED ON THE CIRCUIT BOARD.
NOTE THATTHE IDENTITY OF THE HIGH & LOW P ASS SOCKETS ARE MARKED ON THE BOARD . REFER TO THIS DRAWING FOR LOCA TION
& THE CHART ON THE
BACK FOR THE AVAIL- ABLE SELECTION OF SIP
/ FREQUENCY VALUES.
AMPLIFIER:
BND=BANDPASS LO = LOW PASS HI = HIGH PASS BY= BYPASS
RCA OUTPUTS:
BND=BANDPASS LO = LOW PASS HI = HIGH PASS BY= BYPASS
XTANT TECHNOLOGIES 7676 SOUTH 46TH STREET PHOENIX, ARIZONA 85040 PHONE: 888.449.8268 FAX 602.431.8600
INSTALLER’S REFERENCE
..............
XT ANT 603X
..............
Caution: SHARP EDGES
be careful when
handling top and
bottom metal.
–20 dB = 10V– 17V
–10 dB = 3V – 8V 0 dB = 1V – 3V +10 dB = 300mV–1V +20dB= 100– 300mV
DEFEAT
ENABLE
Loading...