Xtant Technologies 403-A Owners manual

ADDING ACCESSORY MODULES

The 403a is equipped with five accessory docking ports. The four

ports dedicated to the amplifier are labeled

Amp Vert/Hor iz Acc. Port

and

Amp V ert. Acc.Port

. The fifth port is dedicated to the RCAline out-

puts and is labeled

Line Out Vert. Acc. Port

Xtant offers two types of accessory modules which are designed for either “Horizontal” or “Vertical” mounting. The docking port, located behind the RCA line outputs, labeled

Amp Vert/Horiz Acc. Port

will accept any module, while the ports labeled “Vert” will only accept modules designed for vertical mounting.

The four accessory ports dedicated to the amplifier allow you to add the level(s) of signal processing that your system requires. An example would be if a

band pass function

is required, a CM12H (high pass at the lowest frequency of the band pass) and a CM12L(low pass at the highest frequency of the band pass) could be used to create a 12 dB per octave band pass filter. A more basic set-up would be a PQM-1 EQ module and a CM 12 crossover module.

The

Line Out Vert. Acc. Port

will only accept one of the “vertical” accessory modules. This will allow bass equalization or a crossover function to be dedicated to the RCAline outputs. If a module is not used (jumpers in place), signal is still present at the RCA outputs.

FUSING

The 403a does not have an on-board fuse. An out-board, 60 Amp

fuse must be added at the positive terminal of the battery. For

added safety, an outboard 60 Amp

service

fuse may also be added

close to the amplifier.

CONNECTING THE WIRES

Xtant recommends that all wires be terminated with “spade” or “ring

“ style connectors. Care should be taken not to strip the Power,

Ground,Remote Turn-On lead and Speaker Wires over or near the exposed circuit board.If a stray wire falls on the board and power is applied to the amplifier,failure may occur!

There are five sets of speaker terminals provided on the 403a. The

outputs labeled

Chan 1 and 2

are a direct connection to the amplifier.

The terminals labeled

Passive Chan 1 and 2 only become active when one of Xtant’s RM Modules is installed.on the module port towers.

These terminal are connected in parallel to the main terminals via the RM Module.The terminals labeled mono are a direct connection to the amplifier’s mono channel.

For high-powered, bridged operation, connect the speaker(s) to the Channel 1 “plus” terminal and the Channel 2 “minus” terminal. The speaker load across the bridge should be 4Ω or higher. With an RM Module installed, a bridged connection can be made across the “passive” terminals. This output will be attenuated based upon the value of the RM module installed. If a bridge connection is made across both sets of terminals, each speaker load must be 8Ω or higher.

RESISTOR MODULES

The RM Modules serve two purposes – They activate the “

passive

speaker terminals”

while adding attenuation to any speakers connect-

ed to these terminals. Normally, the “

passive terminals”

are used for the rear fill speakers but any speakers (ie tweeters / center channel) that you desire to attenuate (turn down) may be connected to these terminals. The RM Modules offer four levels of attenuation: -4, -8, -12, or -16 dB.The appropriate RM Module is dependent upon speaker efficiency and the distance of the listener to the speakers. In a pick-up truck, where the rear speakers are in relatively close proximity, the higher value RM 12 or RM 16 may be appropriate. In a sedan or coupe, the RM 4 or RM 8 may be better suited. The modules are easily interchanged and a little experimentation will help you determine the best value.

SERVICE JUMPER

This jumper breaks the connection of the Remote Turn-On lead. It has been provided to allow easy “turn-off” and “turn-on” of the amplifier during the fine-tuning process. With the amp playing, simply move the

Remote Turn-On

jumper to

Amp-Off

position, make your adjust-

ments and move the jumper to the

Enable

position to turn the amp back

installer’s reference

xtant technologies

THIS DOCUMENT HAS BEEN CRAFTED TO MAKE INSTALLATION, SYSTEM

EXPANSION AND TROUBLE

-SHOOTING, A QUICK AND EASY PROCESS.THE

INFORMATION PROVIDED

, SHOULD BE REVIEWED PRIOR TO INSTALLING

AND

/OR ADJUSTING THE 403a.

CONNECTING THE HEAD UNIT

The 403a is a three channel, full-range, 400 Watt amplifier . It is equipped with a 2 pair of RCAinput jacks to simplify connection to a standard two or four channel head unit.

Both front and rear inputs must be used when the amplifier is in the 4 channel mode. Only front inputs need be used when you select 2 channel mode on the 2/4 channel jumper. When this procedure is followed, the signal available at both RCA input jacks will be identical. If you intend to utilize the amplifier’s RCAoutput jacks to supply a stereo signal to another amplifier, you must supply a stereo signal to the inputs.

INPUT SENSITIVITY

The input stage of the 403a incorporates Xtant’s

Balanced Line

circuitry.

This circuitry may be “enabled” or disabled (“defeat”) via the

Balanced Input

Mode Jumper

located above and to the left of the RCA input jacks. With the

Balanced Line

circuitry “engaged”, the input sensitivity ranges from 100 mV to 17 Volts. When in the “defeat” mode, input sensitivity ranges from 100 mV to 8 Volts. Input sensitivity is adjustable in 10 dB steps via the

Input Gain Select

jumper located above the

Balanced Input Mode Jumper

. Each of the five jumper positions correlate to a specific range of input signal levels. A chart detailing jumper position to input signal levels is located on the opposite side of this “Installer’s Reference”.

The amplifier is shipped with the

Input Gain

set at the +10 dB position. If you do not know the output signal level of the head unit and you want to change the factory setting, simply move the jumper to the +20 dB position to increase the gain. Move the jumper to the 0, –10 or –20 dB position to decrease the gain.

The input circuitry operates similar to a line driver by increasing the signal level when placed in the +10 and +20 dB positions. The following chart illustrates this function:

INPUT VOLTAGE MULTIPLYING FACTOR

INPUT JUMPER POSITION MULTIPLYING FACTOR

+20 dB = 10 +10 dB = 3

0 dB = 1 –10 dB = .3 –20 dB = .1

(ie: A head unit with 300mV output with input jumper @ +20dB = 3 Volts input)

The input stage may be over-loaded by a high-level signal if the input gain

is set too high. If this should occur, simply reduce the input sensitivity setting.

USING THE BALANCED LINE CIRCUITRY

The

Balanced Line

circuitry provides two unique features which add ver-

satility to your head unit selection. First, the

Balanced Line

circuitry increases the input sensitivity to 17 Volts when receiving a signal from a balanced source and, secondly, isolates signal ground. These two features allow connection with OEM factory head units and high-powered (BTL) head units. The

Balanced Line

circuitry will also accept a speaker level input signal. If the

head unit has a

Floating Ground

output, you must “enable” the

Balanced Line

circuitry prior to connecting the head unit. Failure to

“enable” the

Balanced Line

may result in damage to the head unit.

The

Balanced Line

circuitry also helps eliminate noise (ie alternator whine) induced into the signal cables. If you are experiencing a noise problem, simply “engage” the

Balanced Line

circuitry. If the problem continues, call

Xtant Technologies’ Customer Service at 888•449•8268 for assistance.

•••••••••

OUTPUT GAIN

The output gain for each channel is controlled by board-mounted potentiometers. These pots independently adjust the output level of each channel.Xtant suggests setting this level in conjunction with any equalization or signal processing equipment in the system. Output gain is adjusted independently from the

Input

Gain Select.

If your customer desires max output, don’t be afraid to adjust the

Input Gain

Select

to +20 and turn the output gain pot wide open (full clockwise rotation). If

you should encounter distortion (input clip), turn the amp off via the

Remote T urn-

jumper and reset your

Input Gain Select

to +10. Place the

Remote Turn-On

jumper to the “enable” position and audition the system. Repeat this process if distortion (input clip) continues. The object is to pass as much input signal as possible without over-loading the input stage. Finally, adjust the output pot for desired “max” volume setting on the head unit’s volume control.

DIAGNOSTIC LED’S

The Red LED indicates that the amplifier is on.

The Yellow LED indicates that an over-current condition (low impedance) exist and will turn the amp’s output power down to maintain uninterrupted operation. The Yellow LED will light if a speaker load falls below the 403a’s 2Ω rating and/or a speaker lead / speaker voice coil is shorted.

The Orange LEDindicates that an over-heating condition exists and will turn the amp’s output power down to maintain uninterrupted operation. The Orange LED will light if the heatsink temperature exceeds rated spec due to a blocked air intake or exhaust opening. If the fan should fail, the Orange LED will also light.

TROUBLE SHOOTING

Symptom/Condition Cause Solution

Red LED not on. No Sound. Loss of 12V Power at Amplifier Check out-board fusing

Check +/– 12 Volt connections Measure for + 12 Volts or higher @ amp. Check Turn-On lead

Red LED on. No Sound. No Input Signal Check integrity of RCA cables

Check connection at amp and head Unit.

Red LED on. No Sound. Loose Speaker Wires Check integrity of speaker

connection at amp and speakers.

Red LED on. No Sound. Lack of Turn-On Voltage Voltage @ Turn-On lead needs

to be 8 Volt minimum

Red LED on. No Sound. Missing Accessory Port Jumper Check Port Jumpers, two jumpers

per port are required. Check jumper alignment, jumper must be seated properly.

Red LED on. No Sound. Accessory module not installed properly Be sure “key” on module

connector and port are aligned when installing module. Reseat module to insure proper connection.

Alternator/System Noise Induced noise / ground loop “Enable” Balanced Input

xtant technologies •••••••••

7676 SOUTH 46TH STREET PHOENIX, ARIZONA 85040 USA

••••••••602 431 8686

REV 1197

INSTALLER’S REFERENCE

. . . . . . . . . . .

XTANT 403A

............

remove amplifier cover

Do not remove protective covering until installation is complete.

temporarily mount amplifier

The amplifier is designed to be anchored through the four holes located on the circuit

board/base assembly.

mark wires for termination

Determine wire lengths for Power, Ground, Remote, & Speaker cables. Mark for

cutting/termination. Remove

403a. Cut and terminate all wires. CAUTION:

Stripping wires over the circuit board may cause product failure.

balanced inputs

Make all initial adjustments at your work bench. To select “Balanced Input” for OEM integration or inductive noise cancellation, move the two jumpers, located above and to the left of the

RCAinput connectors to the “enable” position.

input gain

The input gain is factory preset at +10dBand will work with an input signal of

300mVto 1 Volt. To increase the gain, move the jumper to the +20dB position. To

decrease input gain, place jumper in the 0, -10, or -20dBposition.

install accessory modules

At your bench, adjust crossover mode jumpers and change crossover frequency SIP’s . Remove port jumpers and install module(s) – observe “key” on connector for proper fit . Adjust

PQM-1 or LFQ 45 EQmodules after amp is mounted.

mount the amplifier and connect speakers

Two pairs of speaker terminals are provided. The attenuation function of the termi-

nals labeled “passive” is only activated when Xtant’s “passive attenuation boards” –

RM 4, RM 8, RM 12 or RM 16 are installed.

Channel input mode jumper

Both front and rear inputs must be used when the amplifier is in the 4 channel mode. only front inputs need be used when you select 2 channel mode on the 2/4 channel jumper.

make remaining connections

Double check all connections! Turn on amplifier. Check red led, it should be on. If any other adjustments need to be made (crossover modules/input gain adjustment) thE Service jumper may be used to turn the amp off. Make adjustments and place jumper in the enable position to turn the amp back on.

adjust output gain to set system level.

after fine tuning the system,

remove protective

covering and spra y a light coating of

WD40™on a soft cloth and clean cover.

XTANT TECHNOLOGIES 7676 SOUTH 46TH STREET PHOENIX, ARIZONA 85040 PHONE: 888.449.8268 FAX 602.431.8600

amplifier gain controls:

TURN CLOCKWISE TO INCREASE GAIN

Amplifier Accessory Ports

CAUTION:

THE 403AISNOT FUSE PROTECTED! FOR SAFTEY, AN OUTBOARD

60 AMP FUSE MA Y BE ADDED CLOSE TO THE AMPLIFIER.

A 60 AMP FUSE MUST BE INSTALLED IN-LINE

WITH THE POWER WIRE AT THE BATTER

Caution: SHARP EDGES

be careful when

handling top and

bottom metal.

Speaker output terminals:

THE 403A FEATURES TWO PAIRS OF SPEAKER TERMINALS. THE ATTENUATION FUNCTION OF THE TERMINALS LABELED “PASSIVE” IS ACTIVATED WHEN XTANT’S PASSIVE ATTENUATION BOARDS - RM4, RM8, RM12OR RM16 ARE INSTALLED. THE AMOUNT OF SERIES RESISTANCE ADDED WILL REDUCE THE LEVEL OF THE SPEAKER SYSTEM (ATTACHED TO THE “PASSIVE TERMINALS”) BY -4, -8,-12 OR 16 db.

2/4 Channel Jumper

fan

speed

+-+-+-+-+-