Xtant Technologies 3150-X Owners manual

INPUT SENSITIVITY ADJUSTMENT

Each set of inputs (front/rear) on the 3150x are
adjustable in 10 dB steps from -20 dB to + 20 dB The five
(5) input gain settings allow the 3150x to accept input
voltages from 100 mV to 8 V. The front and rear input sen­sitivity is adjusted independently by installing a jumper
across the associated input voltage/pin location. Refer to
the illustration on the reverse side of this document prior
to setting the input sensitivity.

CROSSOVER MODES OF OPERATION

The 3150x is equipped with independent FRONT and
REAR crossovers. Each crossover is controlled by two (2)

crossover mode jumpers labeled AMP & LINE XOVR. The
header jumper labeled AMP XOVR control the crossover
function as it applies to the 3150x’s Front (stereo) and
Rear (mono) amplifier. The modes of operation are: Position
1 = Bypass (Full Range), Position 2 = High Pass, and
Position 3 = Low Pass. (See illustration)

The two (2) header jumpers labeled LINE XOVR control
the crossover function as it applies to the 3150x’s FRONT
and REAR RCA Line Outputs. The modes of operation are:
Position 1 = Bypass (Full Range), Position 2 = High Pass,
and Position 3 = Low Pass. (See illustration )

The High and Low Pass frequencies are determined by the
Frequency Modules (SIPs) installed in the four (4) SIP
sockets pictured on the reverse side of this document.

CROSSOVER FREQUENCY MODULES

The following is a chart of the available Xtant frequency
module SIPs. The frequency module SIP’s “ID Code” printed on
the SIP and the associated frequency value is detailed below.

SIP Number Frequency

224 50 Hz
134 70 Hz
114 80 Hz
104 90 Hz
683 120 Hz
563 150 Hz
273 300 Hz
153 500 Hz
103 700 Hz
682 1 kHz
242 3 kHz
182 4 kHz
152 5 kHz

The 3150x amplifier is shipped from the factory with 90
Hz High Pass and Low Pass frequency modules (SIP)
installed. To change frequency modules, simply remove
each resistor SIP and replace it with the appropriate SIP
value to achieve the desired frequency.

The Low and High Pass frequencies are independent. Any
combination of the available frequency modules (SIPs) may
be used (ie. 80 Hz Low Pass and 120 Hz High Pass).

••••••••••••••••

installer’s reference

xtant technologies

THIS DOCUMENT H A S BEEN CRAFTED TO MAKE INSTALLA-

TION, SYSTEM DESIGN A N D TROUBLE- SHOOTING, A QUICK
A ND EASY PROCESS

. THE CHARTS PROVIDED, OFFER A SIM-

PL E METHOD OF DOCUMENTATION.

IT IS IMPORTANT THAT YOU RETAIN THIS LOG
FOR YOUR RECORDS. O

N PAGE 12 O F THE OWNER’S

MANUAL, YOU WILL FIND THE OWNER’S REFERENCE LOG.
O

NCE YOU HAVE NOTATED THE FINAL SETTINGS FOR THIS

3150X, TRANSFER THOSE SETTINGS TO THE OWNER’S
REFERENCE LOG. IN THE FUTURE, AN Y SYSTEM EXPANSION

AND

/ OR PROBLEMS MA Y BE REFERENCED TO THIS LOG.

INSTALLATION SEQUENCE

REMOVE AMPLIFIER COVER:

Loosen allen head screws and lift-off cover. Do not
remove protective covering on stainless steel lid until
installation is complete.

TEMPORARILY MOUNT AMPLIFIER:

The amplifier is designed to be anchored through the
four (4) sleeved holes located on the circuit
board/base assembly. (see illustration)

REMOVE AMPLIFIER AND MARK WIRES FOR TERMINATION:

Determine wire lengths and mark for cutting/termination.
Remove amplifier base before cutting and terminating
all wires.Caution: stripping wires over the

circuit board may cause product failure.

CROSSOVER SET-UP:

Adjust crossover mode jumpers at your work bench.
Also, change crossover frequency SIP’s if desired.

INPUT SENSITIVITY:

Make initial adjustment to input gain at your work
bench. The factory setting is +10 dB / 300mv -1V. To
increase input gain, place jumper in the +20 dB posi­tion. To decrease input gain, place jumper in the 0 or

-10 dB position.

MOUNT THE AMPLIFIER AND MAKE ALL CONNECTIONS:

Re- install the amplifier base and make all wire con­nections. i.e. Speaker, Power, Remote, Ground, and
RCA input.

DOUBLE CHECK ALL CONNECTIONS

! TURN ON AMPLIFIER.

Check red LED, it should be on.

ADJUST LEFT

, RIGHT & MONO AMPLIFIER OUTPUT LEVELS.

ADJUST NOISE GATE THRESHOLD (IF USED):

Turn noise gate on and adjust the threshold by turn­ing clockwise to increase sensitivity (gate will open
with less input signal). The green LED will illuminate
when the gate passes signal.

AFTER FINE TUNING THE SYSTEM:

Remove protective covering from amplifier and clean
per the maintenance section on page 9 of the Owner’s
Manual. Attach cover to base.

•••••••••

INSTALLER’ S REFERENCE LOG

DA TE INSTALLED:
OWNER’S NAME: PHONE:
A DDRESS:
CITY/STATE: ZIP:
VEHICLE: YEAR:
XTANT AMPLIFIER:MODEL SERIAL#

input sensitivity (CIRCLE SETTING)

FRONT INPUTS (2 CHANNELS) REAR INPUTS ( MONO CHANNEL)

–20dB –10 dB 0dB +10dB +20 dB –20 dB –10 dB 0 dB +10 dB +20 dB

Front Crossover (2 CHANNELS) Rear crossover (MONO CHANNEL)

CIRCLE JUMPER SETTING: CIRCLE JUMPER SETTING:

Amplifier: Amplifier:

ALL HIGH LOW ALL HIGH LOW

rca outputs rca outputs

ALL HIGH LOW ALL HIGH LOW

frequency v alue (2 CHANNELS) frequency value ( MONO CHANNEL)

SIP HIGH PASS FREQUENCY SIP HIGH PA SS FREQUENCY
SIP L O W PASS FREQUENCY SIP LO W P ASS FREQUENCY

output Level adjustment noise gate adjustment

SWITCH: O N OFF

threshold position

Accessory modules (CIRCLE SETTING)(DRAW ARROW POSITION)
CM 24X FRONT REAR pqm-1 ( FRONT) YES N O

YES N O YES N O

pqm-1 CHIP FREQUENCY

BLM-1 FRONT REAR pqm-1 (REAR) YES N O

YES N O YES N O

pqm-1 CHIP FREQUENCY

system components

SOURCE SERIAL #
PROCESSOR( S) SERIAL #

SERIAL #

AMPLIFIER( S) SERIAL #

SERIAL #
SERIAL #

xtant technologies •••••••••

7676 SOUTH 46TH STREET PHOENIX, ARIZONA 85040 USA

••••••••602 431 8686

REV
1197

RIGHTLEFT MONO

MAXI

FUSE

50 AMP

REMOTE

GROUND

+ 12 V

GREEN LED

NOISE GATE

YELLOW LED

LOW IMPEDANCE

LEFT

MONO RIGHT

ORANGE LED

THERMAL PROTECT

RED LED

POWER ON

SPEAKER OUTPUTS

LEFT

LEFTLEFT

LEFT LEFT

LEFT

RIGHTRIGHTRIGHT RIGHT

FRONT REAR

PASSIVE ATTENUA TED

MONO

RIGHT

INPUTS

FRONT

FRONT

FRONT

REAR

REAR

REAR

REARFRONT

OUTPUTS

RCA INPUT

SELECTOR

FRONT INPUT SENSITIVITY

REAR/MONOINPUT SENSITIVITY

PASSIVE (REAR) SPEAKER

ATTENUATION SWITCH

+20
+10

0
–10
–20

+20

4CH INPUT

2 CH INPUT

+10

0

–8dB

–4dB

0dB

–10

–20

+

–

+ POSITIVE

–

– NEGATIVE

+

+

–

–

+

+

–

FRONT XOVR

REAR / MONO XOVR

FAN

CROSSOVER

MODE JUMPERS:

CROSSOVER SIP SOCKETS

CROSSOVER SIP SOCKETS

DEFEAT

IN

2 HP

3 LP

1 BYP

2 HP

3 LP

1 BYP

REMOTE SWITCHED 12 VOLTS

16 GAUGE MINIMUM

NOTE: ADD 50 AMP
FUSE AT POSITIVE TER

-

MINAL OF THE BATTERY .

NOISE GATE SWITCH: UP POSITION = ON; DOWN POSITION = OFF
NOISE GATE THRESHOLD ADJUST: TURN CLOCKWISE TO INCREASE SENSITIVITY

(GA TE WILL OPEN WITH LESS INPUT SIGNAL)

GROUND – 8 GAUGE MINIMUM

POWER

– 8 GAUGE MINIMUM

BRIDGED OUTPUT

ACCESSORY MODULE PORTS

BALANCED LINE MODULE PORTS

INPUT SENSITIVITY:TO ADJUST INPUT GAIN, MOVE JUMPER (IF NEEDED) – AND INSTALL IT IN THE LOCATION WHICH

MATCHES YOUR INPUT SIGNAL LEVEL. REFER TO THE ILLUSTRATION BELOW FOR PROPER JUMPER LOCATION / LEVEL SETTING.

NOTE: –20 dB = 10V – 17V IS ONLY TO BE USED WITH BALANCED INPUT FROM A BALANCED SOURCE.

–20 dB = 10V– 17V

–10 dB = 3V – 8V 0 dB = 1V – 3V +10 dB = 300mV–1V +20dB= 100– 300mV

THIS SYMBOL INDICATES
THE LOCATION OF THE
FOUR

(4) MOUNTING

SLEEVES

.

CROSSOVER

FREQUENCY SELECTION:

TO CHANGE THE FREQUENCY
OF EITHER THE HIGH AND/OR
LOW PASS FIL TERS, REMOVE
AND REPLACE THE 90 HZ
FREQUENCY MODULE (SIP)
INST ALLED ON THE CIR CUIT
BOARD NEXT TO THE
CROSSOVER MODE JUMPERS.

NOTE THAT THE IDENTITY OF
THE HIGH & LOW P ASS
SOCKETS ARE MARKED ON
THE BOARD. HOWEVER, YOU
MA Y REFER T O THIS DRA W-
ING FOR LOCA TION & THE
CHART ON THE BACK FOR
THE INCLUDED SELECTION
OF SIP / FREQUENCY VAL-
UES.

RCA OUTPUTS:

3 – LOW PASS
2 – HIGH PASS
1 – BYPASS

AMPLIFIER:

3 – LOW PASS
2 – HIGH PASS
1 – BYPASS

HIGH PASS

HIGH PASS

INDEPENDENT LEFT, RIGHT AND MONO AMPLIFIER GAIN CONTROLS

ROTATE CLOCKWISE TO INCREASE SENSITIVITY

.

XTANT TECHNOLOGIES 7676 SOUTH 46TH STREET PHOENIX, ARIZONA 85040 PHONE: [phone] FAX [phone]

LOW PASSLOW PASS

INSTALLER’S
REFERENCE

..............

XT ANT 3150X

..............

Caution: SHARP EDGES

be careful when

handling top and

bottom metal.

factory adjustment onl y
do not attempt to adjust

these controls

REMOVE JUMPERS (2) PRIOR TO INSTALLATION
OF ACCESSORY MODULES

. JUMPERS MUST BE

IN

-PLACE WHEN MODULES ARE NOT INSTALLED.

SPEAKER WIRE – 14 GAUGE MINIMUM

RIGHT

RCA

AMP

2 HP

3 LP

1 BYP

2 HP

3 LP

1 BYP

RCA

AMP