X-Rite 301 Operating Manual

X-Rite 301 Operator Manual

i

FCC

This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.

Canada

This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.

NOTE: Shielded interface cables must be used in order to maintain compliance
with the desired FCC and European emission requirements.

For 230V~ replace with 400ma, 5 by 20mm fuse only
For 115V~ replace with 500ma, 5 by 20mm fuse only.

Para 230V~ Reemplazar solamente con el fusible 400ma, dimensión 5mm por

20mm.
Para 115V~ Reemplazar solamente con el fusible 500ma, dimensión 5mm por
20mm.

Per 230V~ Sostituire il fusible solamente con il tipe di 400ma, dimensione 5mm
per 20mm.
Per 115V~ Sostituire il fusible solamente con il tipe di 500ma, dimensione 5mm
per 20mm.

Für 230V~ bitte nur mit einer 400ma Sicherung, Größe 5 mal 20mm, ersetzen!
For 115V~ bitte nur mit einer 500ma Sicherung, Größe 5 mal 20mm, ersetzen!

Pour 230V~ remplaçer seulement par un fusible de 400ma, 5 sur 20mm!
Pour 115V~ remplaçer seulement par un fusible de 500ma, 5 sur 20mm!

X-Rite 301 Operator Manual

ii

Replace with only Same Type Lamp Assembly, X-Rite P/N 301-21.
Ersetzen Sie die Lampenmontage nur mit einer vom gleichen Typ (X-Rite P/N

301-21).
Reemplace la unidad de lampara solamente con una del mismo tipo como la pieza

X-Rite 301-21.
Ne remplacer l’assemblage de lampe qu’avec un assemblage du même type

(X-Rite P/N 301-21).
Sostituire il gruppo di lampada solamente con uno dello stesso tipo che come il

pezzo X-Rite 301-21.

Replace with only Same Type Fluorescent Lamp Assembly, Type F6T5/D.
Ersetzen Sie die Fluoreszenzlampen-Montage nur mit einer vom gleichen Typ

(Typ F6T5/D).
Reemplace la unidad de lampara fluorescente solamente con una del mismo tipo

como la pieza X-Rite F6T5/D.
Ne remplacer l’assemblage de lampe fluorescente qu’avec un assemblage du

même type (type F6T5/D).
Sostituire il gruppo di lampada fluorescente solamente con uno dello stesso tipo

che come il pezzo X-Rite F6T5/D.

Replace with 3/8 Amp-3 AG Fuse Only.
Ersetzen Sie nur mit einer Sicherung von 3/8 Ampere - 3AG.
Reemplace el fusible solamente con el tipo de 3/8 amperios - 3AG.
Ne remplacer qu’avec un fusible de 3/8 ampère - 3 AG.
Sostituire il fusibile solamente con il tipe di 3/8 ampere - 3AG.

X-Rite 301 Operator Manual

iii

CE DECLARATION

Manufacturer's Name: X-Rite, Incorporated
Manufacturer's Address: 3100 44th Street, S.W.

Grandville, Michigan 49418
U.S.A.

Model Name: Densitometer
Model No.: 301

Directive(s) Conformance: EMC 89/336/EEC LVD 73/23/EEC

X-Rite 301 Operator Manual

iv

Relamping Instructions

NOTE: Disconnect Power Before Relamping

Fluorescent Bulbs(s) Replacement

Replace the Fluorescent Bulb(s) as Follows:

1. Remove the four (4) screws on the corners of the light table and remove the
light table.

2. Remove the faulty bulb(s) and replace with type F6T5/D fluorescent bulb(s).

3. Locate the light table and refasten with the four (4) screws.

Anleitung zum Ersetzen der Lampe

N.B. Stromkabel muß dabei ausgezogen werden.

Zum Ersetzen der Fluoreszenz-Leuchtbirne:

Folgen Sie den folgenden Anweisungen:

1. Entfernen Sie die vier (4) Schrauben an den Ecken vom Leuchttisch und
entfernen Sie die Leuchtplatte.

2. Entfernen Sie die kaputten Birnen und ersetzen Sie sie mit Fluoreszenz­Leuchtbirnen vom Typ F6T5/D.

3. Legen Sie die Leuchtplatte wieder auf den Leuchttisch und befestigen Sie sie
mit den vier (4) Schrauben.

Instrucciones de reemplazar la lampara

AVISO: Interrumpa la fuente de energía antes de continuar

El reemplazo de las bombillas fluorescentes

Siga las instrucciones a continuación para reemplazar las bombillas fluorescentes:

1. Quite los quatro (4) tornillos de los ángulos de la mesa luminosa, luego quite la
mesa luminosa.

2. Reemplace las bombillas defectuosas con bombillas fluorescentes del tipo
F6T5/D.

3. Coloque la mesa luminosa en su sitio y asegúrela apretando con los quatro (4)
tornillos.

Instructions pour remplacer l’ampoule d’éclairage
fluorescent

ATTENTION: Pour commencer, déconnecter le cordon secteur.

Pour remplacer l’ampoule d’éclairage fluorescent

Suivre les instructions suivantes:

1. Enlever les quatre (4) vis dans les coins de la table lumineux, et démonter la
plaque translucide.

2. Enlever l’ampoule d’éclairage cassé et le remplacer avec un ampoule d’éclairage
fluorescent du type F6T5/D.

3. Remplacer la plaque translucide et la retenir avec les quatre (4) vis.

Istruzioni per sostituire la lampada

AVVISO: Interrompere l’energia prima di continuare
La sostituzione delle lampade fluorescenti
Eseguire l’istruzioni seguenti per sostituire le lampade fluorescenti:

1. Togliere le quattro (4) viti dei angoli del tavolo luminoso, quindi togliere il
tavolo luminoso.

2. Sostituire le lampade difettose con lampade fluorescenti del tipo F6T5/D.

3. Collocare il tavolo luminoso en suo posto y assicurarlo con le quattro (4) viti.

X-Rite 301 Operator Manual

v

Dear Customer:
Congratulations! We at X-Rite, Incorporated are proud to present you with

your X-Rite 301 Black and White Transmission Densitometer. Your 301 is a
rugged and reliable instrument whose performance and design exhibit the
qualities of a finely engineered laboratory instrument.

To fully appreciate and protect your investment, we suggest that you take
several minutes to read this manual. As always, X-Rite stands behind your 301
Instrument with a full one-year limited warranty and a dedicated service
organization. If the need arises, please do not hesitate to call on us.

Thank you for your trust and confidence.

X-Rite, Incorporated

X-Rite 301 Operator Manual

vi

CUSTOMER INFORMATION

These provisions are intended to state all of the rights and responsibilities
between X-Rite, Incorporated and customer. They take the place of and
supersede all warranties, express or implied, and whether of
merchantability, fitness, or otherwise. The remedies contained in this
installation and operation manual are exclusive. Customer and X-Rite,
Incorporated waive all other remedies, including but limited to,
consequential damages.

Limited Warranty

X-Rite, Incorporated warrants each instrument manufactured by them to
be free of defects in materials and workmanship for a period of 12 months.
THERE ARE NO WARRANTIES OF MECHANTABILITY OR
FITNESS. THIS WARRANTY OBLIGATION IS LIMITED TO
SERVICING THE UNIT RETURNED TO THE FACTORY FOR THAT
PURPOSE AND EXCLUDES THE TUNGSTEN-HALOGEN LAMPS.
The instrument shall be returned with transportation charges prepaid. If
the fault has been caused by misuse or abnormal conditions of operation,
repair will be billed at a nominal cost. If requested, an estimate will be
submitted before non warranty work is started.

An Instrument Registration Card is enclosed with each instrument.
The purchaser should fill in the card completely and return it to X-Rite
postmarked no later than 10 days form the date of receipt. This card
registers your instrument with us for warranty coverage. Once your
instrument is registered we are able to maintain a file to help expedite
service in case it is needed. Always include serial number and place of
purchase in any correspondence concerning your instrument. The serial
number is located at the rear of the instrument.

X-Rite, Incorporated offers a repair program for instruments out of
warranty. For more information, contact X-Rite Instrument Services
Department.

This agreement shall be interpreted in accordance with the laws of the
State of Michigan and jurisdiction and venue shall lie within the courts of
Michigan as selected by X-Rite, Incorporated.

X-Rite 301 Operator Manual

vii

Proprietary Notice

The information contained in this manual is derived from patent and
proprietary data from X-Rite, Incorporated. This manual has been
prepared solely for the purpose of assisting operation and maintenance
personnel in their use of the X-Rite 301 Instrument.

The contents of this manual are the property of X-Rite, Incorporated and
are copyrighted. Any reproduction in whole or part is strictly prohibited.
Publication of this information does not imply any rights to reproduce it or
use it for any purpose other than installing, operating, or maintaining the
equipment described herein.

This instrument is covered by the following U.S. and foreign patents:
U.S. Patent #4,080,075 and other patents pending.

Copyright ©1984, 1996, 1999 by X-Rite, Incorporated.
“ALL RIGHTS RESERVED.”

X-Rite 301 Operator Manual

viii

TABLE OF CONTENTS

Customer Information................................................................. vi

Relamping Instructions...............................................................iv

Table of Contents.......................................................................viii

List of Figures ............................................................................viii

Introduction .................................................................................. 1

Specifications .......................................................................... 1

Unpacking................................................................................3

Operating Instructions................................................................. 2

Power Application...................................................................2

Aperture Replacement............................................................. 3

Nulling (Zeroing) Procedure....................................................3

Absolute Density Measurement...............................................4

Density Comparison Measurement..........................................4

Calibration ....................................................................................5

Calibration Frequency .............................................................5

Calibration Procedure..............................................................5

Maintenance..................................................................................7

Cleaning................................................................................... 7

Fluorescent Bulb Replacement................................................ 8

Reading Lamp Replacement....................................................9

Fuse Replacement..................................................................10

Factory Repair....................................................................... 11

Troubleshooting.......................................................................... 12

Output Connection (model 301RS) ........................................... 14

RS-232 Connection................................................................14

Data Instruction Format.........................................................15

LIST OF FIGURES

Figure 1. Applying Power.............................................................2

Figure 2. Aperture Removal ......................................................... 3

Figure 3. Calibration..................................................................... 6

Figure 4. Calibration Step Tablet.................................................. 6

Figure 5. Cleaning Instrument Optics........................................... 7

Figure 6. Fluorescent Lamp Access.............................................. 8

Figure 7. Lamp PC Board Access.................................................9

Figure 8. Densitometer PC Board Access................................... 10

Figure 9. Transmit Function Switch Access ............................... 13

1

INTRODUCTION

The X-Rite 301 Black and White Densitometer is a highly accurate and
reliable instrument designed for ease of operation. This unit features push
button nulling and will compute density comparisons and subtractions.
Voltage and temperature compensation provides drift-free operation.

SPECIFICATIONS

Size:.......................................... 10.25W x 15L x 5.25H

Weight: ..................................... 8.5lbs.

Range:....................................... 0 to 5.0D w/2mm and 3mm apertures

.......................................... 0 to 4.0D with 1mm aperture

Accuracy:.................................. ±0.02D

.......................................... ±1.5%D (1mm aperture, 3.5D to 4.0D)

Repeatability:............................ ±0.01D

Operating Temp. Range:........... +10° to +40°C (+50° to 104°F)

Operating Relative Humidity:... ≤76%

Voltage Range: ......................... 301 (Domestic) 100Vac to 130Vac, 60Hz

301X (Export) 200Vac to 240Vac, 50Hz

Power Requirement: ................. 80VA maximum

Warm-up Time:......................... 60 seconds

Scale Factor Stability:............... ±1.0% per six months

Null Drift:................................. ±0.03D max., ±0.01D typical

Safety........................................ UL 3101-01

.......................................... C22.2, No. 1010-1-92

Altitude..................................... 2000m

IEC 664..................................... Pollution Degree 2

Installation Type....................... Category 2

Usage........................................ Indoor only

FCC .......................................... Part 15, Class A, Digital Device

Industry Canada........................ ICES-003 Issue 2, Revision 1

International.............................. EN50081-1:1992

.......................................... Class B Generic Emmision Standard

.......................................... EN50082-1:1992

.......................................... Generic Immunity Standard

NOTE: Due to heat generated by the fluorescent lamps, accuracy

to the 301 Densitometer is improved with the lamps off.

Operating Instructions

2

UNPACKING

Remove the instrument from shipping carton. Inspect for possible damage.
If any damage is noted, contact the transportation company immediately.
Do nothing more until the carrier’s agent has inspected the damage.

If damage is not evident, make sure the following items are included.

• X-Rite 301 Operation Manual (with Warranty Card)

• 1mm, 2mm and 3mm apertures (inside back cover of manual)

• Standard Reference Step Tablet (inside front cover of manual)

• 301(X) Instrument

OPERATING INSTRUCTIONS

Operation of the X-Rite 301 is very simple. Procedures of the various
modes of operation are provided in the following paragraphs. When
operating the instrument, use these recommended common sense
suggestions to protect yourself and your instrument:

• Avoid dangerous environments (e.g., don’t use instrument in damp,

wet areas)

• Use proper electrical connections.

• Ensure electric cord does not interfere with work.

• Disconnect power before servicing.

POWER APPLICATION

The 301(X) is designed to operate from a standard grounded line source.
Always plug the instrument into a 3-wire receptacle.

1. Plug line cord into a 3-wire grounded outlet.

2. Turn on power switch.

Operating Instructions

3

APERTURE REPLACEMENT

Remove the installed aperture by lifting the edge upward. Install a new or
different aperture by inserting the aperture into the light source cavity,
making sure that the aperture is fully seated and pressed flush against the
cavity.

Figure 2. Aperture Removal

NULLING (ZEROING) PROCEDURE

Due to the electronic memory loss caused by power removal, null must be
established each time power to the instrument is removed. Null remains
very stable (±0.01D) as long as power remains on.

Null the instrument as follows:

1. Remove film from reading area.

2. Lower the reading head by pressing the read button until it deflects

totally and actuates the switch.

3. Momentarily push the null button.

4. Remove pressure on the read button to release the reading head.

NOTE: The read button is a read-hold activator. Compress the

button with only as much pressure as necessary for total
deflection.

Read Button

Operating Instructions

4

ABSOLUTE DENSITY MEASUREMENT

Measure absolute density as follows:

1. Null the instrument as previously described in Nulling (Zeroing)

Procedure.

2. Center the film area directly over the bright green light spot under the

reading head.

3. Lower the reading head by pressing the read button until it totally

deflects and actuates the switch.

4. Allow the instrument reading to settle to a stable number.

5. Remove pressure on the read button to release the reading head.

NOTE: Always measure density with the film emulsion side up.

When measuring density values above 2.50D, ensure that
reading head light seal is completely on surface of the film
being measured.

DENSITY COMPARISON MEASUREMENT

Compare density readings as follows:

1. Place reference film over aperture. Press read button and momentarily

press the null button.

2. Place the film to be compared over the aperture and measure density.

• This measurement is the difference between the reference film

density and the compared film density.

• A negative (–) display indicates a lower compared film density

than the reference film.

NOTE: When referencing with densities greater than 3.00D,

press the null button longer to allow the instrument
electronics to fully stabilize.

5

CALIBRATION

Calibration of this instrument should remain stable over a long period of
time and over an extended range of voltage and temperature. However, a
calibrated step tablet is provided (inside front cover) to verify the
instrument calibration. Handle the step tablet with care to prevent
accumulation of dirt and fingerprints on the surface.

CALIBRATION FREQUENCY

Under normal operating conditions, the instrument calibration should be
verified once a week by the following the Calibration Procedure.

CALIBRATION PROCEDURE

See illustrations on the following page for calibration adjustment locations
and reference.

To verify calibration:

1. Null the instrument as described in Nulling (Zeroing) Procedure page

1. Center the “CAL” portion of step tablet under read head.

2. Press read button to measure step tablet.

3. Hold read button down until a stable reading is attained.

• The “CAL” reading should be ±0.02D of the “CAL” value marked

on the step tablet.

If “CAL” reading is NOT within tolerance, calibrate instrument.

To calibrate instrument:

1. Center the “CAL” portion of step tablet under the read head .

2. Press and hold read button to measure the step tablet.

3. Use a small screwdriver or adjustment tool into hole on the right side

of instrument, to engage the calibration adjustment (potentiometer).

4. With read button still depressed, adjust as necessary to within ±0.02D

of the “CAL” value marked on the calibrated step tablet.

• Rotate counterclockwise to increase value, clockwise to decrease.

5. Remove step tablet and press read button to check null, re-null the

instrument as necessary.

6. Repeat until the calibration value and null are within tolerance.

NOTE: Always return the step tablet to the plastic bag on inside

front cover for protection.

Calibration

6

Figure 3. Calibration

Figure 4. Calibration Step Tablet

“CAL” portion of step tablet
centered on Target Window

Calibration Adjustment

Read Button

Calibration Point

CAL Density

Value

7

MAINTENANCE

The 301 Densitometer is completely covered by a one (1) year warranty
and should be referred to the factory or authorized service center for
repairs within the warranty period. Attempts to make repairs within the
warranty period may void the warranty. If repairs are needed after the
warranty period, only qualified technicians should perform such repairs.
Refer to the exploded view illustration of the 301 on page 16.

WARNING: DISCONNECT POWER BEFORE PERFORMING

ANY MAINTENANCE.

CLEANING

General cleaning of the 301 Densitometer should be done with mild a soap
solution.

CAUTION: Do not use alcohol based solutions to clean light

table.

Clean the instrument optics (apertures and read head opal glass) with a
cotton swab moistened with alcohol. Remove residue and lint with lens
paper. See Figure 5.

CAUTION: To prevent contamination of optics, always cover

the reading area when cleaning the opal glass.

Figure 5. Cleaning Instrument Optics

Cover read area

and aperture

Read Button

Cotton Swab

Maintenance

8

FLUORESCENT BULB REPLACEMENT

Replace fluorescent bulbs as follows:

1. Remove four (4) screws securing light table to the unit chassis.

2. Remove light table.

3. Remove the faulty bulb(s) and replace with new, type F6T5/D

fluorescent bulb(s).

4. Reinstall light table and secure to unit chassis with four (4) screws.

Figure 6. Fluorescent Bulb Access

Screws Lamp

Maintenance

9

READING LAMP REPLACEMENT (P/N 301-21)

Replace the reading area lamp as follows:

1. Remove the unit bottom cover by removing the four (4) screws located

in the rubber feet.

2. Remove the four (4) screws securing the Lamp P.C. board to the arm

assembly at bottom of chassis.

3. Disconnect lamp connector and remove faulty Lamp P.C. board.

NOTE: Ensure lamp P.C. board bulb is clean. Use alcohol on a

lint free cloth or cotton swab to remove smudges.

CAUTION: The bulb on Lamp P.C. board has been prealigned

for optimum optical performance. Use care not to
bend or reposition the bulb when cleaning or
installing.

4 Connect the lamp connector to new Lamp P.C. board.

5. Secure Lamp P.C. board to arm assembly with four (4) screws.

6. Reinstall bottom cover and secure with four (4) screws.

Figure 7. Lamp PC Board Access

Screws

Screws

Lamp PC
Board Assy

Lamp Connector

Maintenance

10

FUSE REPLACEMENT

NOTE: Your 115VAC instrument may have a “twist-off” type fuse

carrier not shown below. If this is the case, replace fuse
with a 500ma, ¼” x 1-¼” type.

A spare fuse is located in the fuse carrier if required.

To replace fuse:

1. Turn power off (O) and remove detachable line cord.

2. Insert small flat-blade screwdriver into left edge of fuse carrier and pry

out.

3. Remove blown fuse from carrier clip and discard.

4. Remove spare fuse from carrier compartment and place in fuse clip.

5. Reinsert fuse carrier into fuse cavity. Make sure carrier is firmly

seated.

6. Reinstall detachable line cord.

Flat-blade Screwdriver

Power Switch

Fuse Carrier

Maintenance

11

FACTORY REPAIR

X-Rite recognizes the need to provide complete technical repair service to
customers. X-Rite provides repair of any 301 submitted past warranty. The
customer shall pay shipping costs and the instrument shall be submitted in
its original shipping carton as a complete unaltered unit.

Spare Fuse

Fuse Location

Fuse Carrier

12

TROUBLESHOOTING

The following chart is included to aid in troubleshooting your 301
instrument. Use care to avoid danger of electrical shock when
troubleshooting or performing any type of maintenance. Only qualified
technicians should perform repairs.

WARNING: DISCONNECT POWER BEFORE REPLACING PARTS.

PROBLEM CAUSE REMEDY

Unit keeps blowing
fuses (500ma for 301)
(400ma for 301X)

Fuse loose in holder
Short in p.c. board
Short in wiring
Short in ballast
Short in transformer

Tighten fuse holder
*
*
*
*

Unit display will not
turn on

Unit not nulled
Blown fuse
Loose connector(s)
Faulty P.C. board
Faulty switch
Bad transformer winding
Open wiring

Null unit
Replace fuse
Re-seat connector(s)
*
*
*
*

Light source will not
illuminate

Blown fuse
Loose connector(s)
Faulty Lamp P.C. board
Faulty switch
Bad transformer winding
Open wiring

Replace fuse
Re-seat connector(s)
*
*
*
*

Unit will not Null Faulty light source

Faulty P.C. board
Faulty null switch
Loose connector(s)
Faulty sensor wiring
Faulty sensor(s)

(See light source)
*
Replace switch
Re-seat connector
*
*

* = Contact X-Rite Instrument Services or an authorized service center for

repair.

Troubleshooting

13

PROBLEM CAUSE REMEDY

Fluorescent bulb(s)
will not illuminate

Loose bulb(s)
Blown fuse
Loose connector
Faulty bulb(s)
Faulty switch
Faulty ballast(s)
Open wiring

Seat bulb(s)
Replace fuse
Re-seat connector
Replace bulb(s)
*
*
*

Reading will not
change or hold

Loose connector(s)
Faulty P.C. board
Faulty switch
Open wiring

Re-set connector
*
*
*

* = Contact X-Rite Instrument Services or an authorized service center for

repair.

14

OUTPUT CONNECTION (301RS)

The Model 301RS has the capability of sending measurement data to a
printer, computer, or modem. This is done through the use of a RS-232
output connection located in the rear of the instrument. Data is sent each
time the READ button is released.

RS-232 CONNECTION

Use a RS-232S type cable to connect the 301RS and the receiving device.
The Transmit Function Switch, located inside the instrument, must be set
to DTE (Data Terminal Equipment) or DCE (Data Communication
Equipment) to correspond with the receiving device. The DTE setting
sends the TRANSMIT signal through pin 2 and is normally used for
printers or computers outputs. The DCE setting sends the TRANSMIT
signal through pin 3 and is normally used for modem outputs.

NOTE: The output connection is preset from factory to DTE

operation for X-Rite 301 units and DCE operation for Fuji
301 units.

To change the Transmit Function Switch setting:

1. Disconnect power to instrument.

2. Turn unit upside down and remove bottom cover by the four screws in

located in the rubber feet.

3. Set the Transmit Function Switch to DTE for printer or computer

connections or DCE for modem connections.

4. Return bottom cover in place and secure with four screws.

Figure 9. Transmit Function Switch Access

Screws

RS-232 Connection

Transmit Function
Switch

Troubleshooting

15

DATA INSTRUCTION FORMAT

Data is sent in the following format:

<Lead Character><Units><Tenths><Hundredths><Carriage
Return>

Lead Character represents the ASCII code for a positive character
(space) or negative character (–).

Units, Tenths, & Hundredths are three ASCII digits (0-9) representing
density values.

Data is transmitted at the rate of 300 baud with one start bit and stop bit,
and the parity bit set to logic zero.

Output logic level is −5Vdc to +5Vdc
DTE (Pin 2 = TRANSMIT)
DCE (Pin 3 = TRANSMIT)
Ground = Pin 7

X--Rite, Incorporated—World Headquarters

3100 44th Street S.W. • Grandville, Michigan 49418 • USA
www.x-rite.com • [phone]
Toll-Free U.S. Numbers
Tel: [phone] • Fax: [phone]
Toll-Free International Numbers
Tel: [phone] • Fax: [phone]

X-Rite GmbH

Stollwerckstraße 32 • 51149 Köln • Germany
Tel: [phone] • Fax: [phone]

X-Rite GmbH

Sochorova 705 • CZ-682 • 11 Vyskov • Czech Republic
Tel: [phone] • Fax: [phone]

X-Rite Asia Pacific Ltd.

Room 808-10 • Kornhill Metro Tower • 1 Kornhill Road
Hong Kong • Tel: [phone] • Fax: [phone]

X-Rite Ltd.

The Acumen Centre • First Avenue
Poynton, Cheshire • England
Tel: [phone] • Fax: [phone]

X-Rite Méditerranée

Parc du moulin de Massy • 35, rue du Saule Trapu • 91300 Massy • France
Tel: [phone] • FAX [phone]

X-Rite Asia Pacific Limited - Japan Office

Suite 506 AIOS Gotanda • 1-7-11 Higashi-Gotanda
Shinagawa-ku, Tokyo • 141-0022 Japan
Tel: [phone] • Fax: [phone]

P/N 301-30 Rev. JJ-11/18/99