Page 1
Platform: DBALL2
Firmware GM10 Range Extender Ready (RXT) Installation:
Update Alert: Firmware updates are posted to the web on a regular basis. We recommend
that you check for firmware and/or install guide updates prior to installing this product.
Installation Guide
This guide supports the installation of a in Range Extender Ready ( ) mode withDBALL RXT
or without a Plug & Play T-Harness 1 1 ores / DOBDTHDGM OBDGM
OBDTHDGM OBDGM RF2 (optional) Kit or SmartStart (all sold separately)./D2 ,
Range Extender Ready ( ) is usedRXT to dramatically increase the factory remote start activation range
compared to the factory transmitter
Note sold separately: optional .T-Harness 1 1 or 2es / D / D2 areOBDTHDGM OBDGM OBDTHDGM OBDGM
Important:
- 3.18This guide is compatible with the 10 firmware version and higher.GM
- starter.This product is compatible with vehicles equipped with a factory-installed remoteONLY
. Refer to the for more information.Quick Reference Guide
Rev.: 20 701 821
Index
Vehicle Application Guide ....... ................................................... ............................... .......................................................
Installation
Wiring Diagram ...... ... ... ..with T-Harness ..... ..................................................................................... . ..............................
Wiring Diagram ......... ... ..without T-Harness....................... ....................................................................................... . .....
Vehicle Wiring Reference Chart......................................................................................................................................
SmartStart/ 202 Installation Notes...............................................................................................................................XL
Programming
Module Programming....................................... ................................................................................ ...............................
Module Reset & Hard Reset......... ...................................................................... ... .................................................. ........
Feature & Option List... ..................................................................................................................... ...............................
Feature Programming......................................................................................................................................................
LED Diagnostics ..................................................................................................................& Troubleshooting. .............
Limited One-Year Consumer .......Warranty.....................................................................................................................
Quick Reference Guide ...................... ....... ...................................................................................................................... .......... ......
SmartStart Compatible
SmartStart is equipped with D2D which means it can be connected to an interface module and used in, Range
Extender Ready ( ) mode the use of See the section forRXT without a remote starter. Module Programming
more information.
02
03
04
05
11
12
13
14
15
16
18
19
® are registered trademarks and property of .Buick, Chevrolet and their respective companies.GMC
© 2017 Directed. All rights reserved.
Page 2
Vehicles
2017
2016
2015
2014
2013
2012
2011
2010
CC-Heated Seats Ac tivation
DL-Arm Factory Security
DL-Disarm Factory Security
DL-Door Loc k Control
DL-Door U nlock
DL-Driver Priority Unlock
RS-OEM Remote Start Activation
using XL-202 or R F kit
RS-SmartStart
Buick
Encore
•••• ••••• • •
LaCrosse
••••••• ••••• • •
Regal
••••• ••••• • •
Verano
•••••• ••••• • •
Che vrol et
Camaro
•••• •••••• • •
Camaro
•• ••••• • •
Colorado
•• ••••• • •
Cruze
••••••• ••••• • •
Cruze Limited
• ••••• • •
Equinox
•••••• •••••• • •
Equinox
•• ••••• • •
Impa la
••• ••••• • •
Malibu
••• ••••• • •
Malibu Limited
• ••••• • •
Orlando
•• ••••• • •
Silverado 1500
[2]
••• ••••• • •
Silverado 2500/3500
[2]
•• ••••• • •
Sonic
••••• ••••• • •
Spark
[1]
•••• ••••• • •
Suburban
• ••••• • •
Tah oe
• ••••• • •
Trax
••••
••••• • •
GMC
Canyon
•• ••••• • •
Sierra 1500
[2]
••• ••••• • •
Sierra 2500/ 3500
[2]
•• ••••• • •
Terrain
•••••••• ••••• • •
Yukon
• ••••• • •
Legend:
CC: Comfort & Convenience Controls
DL: OEDoor Lock & Alarm Controls
RS: Remote Start & Engine Controls
Platform: DBALL2
Firmware GM10 Range Extender Ready (RXT) Installation:
Rev.: 20 701 821
Vehicle Application Guide
The table below lists the vehicles and features which are compatible with this product. Refer to the following pages for
more information on installation wiring, programming and troubleshooting for these vehicles.
Page 2
[1] T-Harness 610 is compatible with Chevrolet Spark.THGM /THGM610D 2013-2015not
[2] T-Harness 610 is compatible with these models the vehicle is equipped with OnStar.THGM ONLY IF/THGM610D
© 2017 Directed. All rights reserved.
Page 3
Platform: DBALL2
Firmware GM10 Range Extender Ready (RXT) Installation:
Wiring Diagram with T-Harness
Important!
Refer to the Quick Reference Guide for more information on Range Extender Ready ( ).RXT
1. Remove the factory Diagnostic
Connector ( ) from the dash.OBDII
2. Screw style
(# 1/ D1) or clipOBDTHDGM OBDGM
style (# 2/ D2)OBDTHDGM OBDGM
the black female connector to replace
the factory connector.OBDII
Rev.: 20 701 821
Page 3
14
Factory Diagnostic
Connector ( )OBDII
T-Harness Male
connector
#1/D1OBDTHDGM OBDGM
#2/D2OBDTHDGM OBDGM
T-Harness Female
Connector
T-Harness
(Optional)
Note: Diagnostic Connector ( )OBDII
functions will remain identical even
with the T-Harness installed.
12
2
RF
Prog. uttonB
LED
10
DBALL/
4
2DBALL
You can connect to either a 202XL
RFTD a SmartStart module.OR
Refer to the SmartStart/ 202XL
Installation Notes for more information.
© 2017 Directed. All rights reserved.
Page 4
Platform: DBALL2
Firmware GM10 Range Extender Ready (RXT) Installation:
Wiring Diagram without T-Harness
Important!
Refer to the Quick Reference Guide for more information on Range Extender Ready ( ).RXT
Rev.: 20 701 821
Page 4
SW C : pin 1AN Green,
Black, pin 4
(-) Ground:
18
HS CA N Low:
Tan or White, pin 14
Diagnostic Connector
(connector side view)OBDII
HS CA N High:
Tan/Black or Blue, pin 6
169
(+)12V: pin 16
Single Wire CAN: 1Light Green:
[1] HS C AN High: 3Tan/Black:
[1] Tan:HS CAN Low: 4
(+) 12V: 13Red:
(-) Ground: 14Black:
14
12
2
RF
Prog. uttonB
LED
DBALL/
10
4
2DBALL
You can connect to either a 202XL
RFTD a SmartStart module.OR
Refer to the SmartStart/ 202XL
Installation Notes for more information.
[1] These wires must be connected only if installed with SmartStart.
© 2017 Directed. All rights reserved.
Page 5
Platform: DBALL2
Function Color Pin Polarity Location Color Pins
SW CAN Green 1 Data
OBDII Connector
Black 16
CAN High Blue 6 Data
OBDII Connector
Black 16
CAN Low White 14 Data
OBDII Connector
Black 16
(+) 12V Red/Brown 16 (+)
OBDII Connector
Black 16
Ground Black 4 (-)
OBDII Connector
Black 16
SW CAN Dk. Green
1Data
OBDII Connector
Black 16
CAN High Tan/Black
6Data
OBDII Connector
Black 16
CAN Low Tan
14 Data
OBDII Connector
Black 16
(+) 12V Red/White 16 (+)
OBDII Connector
Black 16
Ground Black 4 (-)
OBDII Connector
Black 16
SW CAN Green
1Data
OBDII Connector
Black 16
CAN High Dk. Blue
6Data
OBDII Connector
Black 16
CAN Low White
14 Data
OBDII Connector
Black 16
(+) 12V Red/Dk.Green 16 (+)
OBDII Connector
Black 16
Ground Black 4 (-)
OBDII Connector
Black 16
SW CAN Green
1Data
OBDII Connector
Black 16
CAN High Blue
6Data
OBDII Connector
Black 16
CAN Low White
14 Data
OBDII Connector
Black 16
(+) 12V Red/White 16 (+)
OBDII Connector
Black 16
Ground Black 4 (-)
OBDII Connector
Black 16
SW CAN Green
1Data
OBDII Connector
Black 16
CAN High Blue
6Data
OBDII Connector
Black 16
CAN Low White
14 Data
OBDII Connector
Black 16
(+) 12V Red/White 16 (+)
OBDII Connector
Black 16
Ground Black 4 (-)
OBDII Connector
Black 16
Buick Regal 2011-2012
Buick Regal 2013-2015
Wire Information Connector Information
Buick Encore 2013-2016
Buick La Crosse 2010
Buick LaCrosse 2011-2016
Firmware GM10 Range Extender Ready (RXT) Installation:
Vehicle Wiring Reference Chart
Wire colors should only be used as a reference. You should always test a wire's function and pin location before
connecting to it.
Rev.: 20 701 821
Page 5
© 2017 Directed. All rights reserved.
Page 6
Platform: DBALL2
Function Color Pin Polarity Location Color Pins
SW CAN Green
1Data
OBDII Connector
Black 16
CAN High Blue
6Data
OBDII Connector
Black 16
CAN Low White
14 Data
OBDII Connector
Black 16
(+) 12V Red/White 16 (+)
OBDII Connector
Black 16
Ground Black 4 (-)
OBDII Connector
Black 16
SW CAN Green
1Data
OBDII Connector
Black 16
CAN High Blue
6Data
OBDII Connector
Black 16
CAN Low White
14 Data
OBDII Connector
Black 16
(+) 12V Red/Violet 16 (+)
OBDII Connector
Black 16
Ground Black 4 (-)
OBDII Connector
Black 16
SW CAN Dk. Green
1Data
OBDII Connector
Black 16
CAN High Tan/Black
6Data
OBDII Connector
Black 16
CAN Low Tan
14 Data
OBDII Connector
Black 16
(+) 12V Red/White 16 (+)
OBDII Connector
Black 16
Ground Black 4 (-)
OBDII Connector
Black 16
SW CAN Lt Green 1 Data OBDII Connector Black 16
CAN High Lt. Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
(+) 12V Red 16 (+) OBDII Connector Black 16
Ground Black 4 (-) OBDII Connector Black 16
SW CAN Green 1
Data
OBDII Connector Black 16
CAN High Blue 6
Data
OBDII Connector Black 16
CAN Low White 14
Data
OBDII Connector Black 16
(+) 12V Red/Dk. Blue 16 (+)
OBDII Connector
Black 16
Ground Black 4 (-)
OBDII Connector
Black 16
Chevrolet Camaro 2010-2015
Chevrolet Colora do 2015-2016
Chevrolet Cruze 2011-2017
Wire Information Connector Information
Buick Verano 2012
Buick Verano 2013-2017
Firmware GM10 Range Extender Ready (RXT) Installation:
Vehicle Wiring Reference Chart
Wire colors should only be used as a reference. You should always test a wire's function and pin location before
connecting to it.
Rev.: 20 701 821
Page 6
© 2017 Directed. All rights reserved.
Page 7
Platform: DBALL2
Function Color Pin Polarity Location Color Pins
SW CAN Dk. Green 1 Data OBDII Connector Black 16
CAN High Tan/Black 6 Data OBDII Connector Black 16
CAN Low Tan 14 Data OBDII Connector Black 16
(+) 12V Red/W hite 16 (+) OBDII Connector Black 16
Ground Black 4 (-) OBDII Connector Black 16
SW CAN Dk. Green 1 Data OBDII Connector Black 16
CAN High Tan/Black 6 Data OBDII Connector Black 16
CAN Low Tan 14 Data OBDII Connector Black 16
(+) 12V Red/Lt. Green 16 (+) OBDII Connector Black 16
Ground Black 4 (-) OBDII Connector Black 16
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
(+) 12V Red/Green 16 (+) OBDII Connector Black 16
Ground Black 4 (-) OBDII Connector Black 16
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
(+) 12V Red/Green 16 (+) OBDII Connector Black 16
Ground Black 4 (-) OBDII Connector Black 16
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
(+) 12V Red/Dk. Blue 16 (+) OBDII Connector Black 16
Ground Black 4 (-) OBDII Connector Black 16
Chevrolet Orlando 2012-2013
Wire Information Connector Information
Chevrolet Equinox 2010-2017
Chevrolet Impala 2014-2015
Chevrolet Malibu 2013-2015
Chevrolet Malibu Limited 2016
Firmware GM10 Range Extender Ready (RXT) Installation:
Vehicle Wiring Reference Chart
Wire colors should only be used as a reference. You should always test a wire's function and pin location before
connecting to it.
Rev.: 20 701 821
Page 7
© 2017 Directed. All rights reserved.
Page 8
Platform: DBALL2
Function Color Pin Polarity Location Color Pins
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low W hite 14 Data OBDII Connector Black 16
(+) 12V Red/White 16 (+) OBDII Connector Black 16
Ground Black 4 (-) OBDII Connector Black 16
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low W hite 14 Data OBDII Connector Black 16
(+) 12V Red/White 16 (+) OBDII Connector Black 16
Ground Black 4 (-) OBDII Connector Black 16
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low W hite 14 Data OBDII Connector Black 16
(+) 12V Red/Yellow 16 (+) OBDII Connector Black 16
Ground Black 4 (-) OBDII Connector Black 16
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low W hite 14 Data OBDII Connector Black 16
(+) 12V Red/Brown 14 (+) OBDII Connector Black 16
Ground Black 14 (-) OBDII Connector Black 16
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low W hite 14 Data OBDII Connector Black 16
(+) 12V Red/White 16 (+) OBDII Connector Black 16
Ground Black 4 (-) OBDII Connector Black 16
Chevrolet Suburban 2015
Wire Information Connector Information
Chevrolet Silverado 2500/3500 2016
Chevrolet Sonic 2012-2016
Chevrolet Spark 2013-2016
Chevrolet Silverado 1500 2014-2016
Firmware GM10 Range Extender Ready (RXT) Installation:
Vehicle Wiring Reference Chart
Wire colors should only be used as a reference. You should always test a wire's function and pin location before
connecting to it.
Rev.: 20 701 821
Page 8
© 2017 Directed. All rights reserved.
Page 9
Platform: DBALL2
Function Color Pin Polarity Location Color Pins
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
(+) 12V Red/White 16 (+) OBDII Connector Black 16
Ground Black 4 (-) OBDII Connector Black 16
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
(+) 12V Red/Brown 16 (+) OBDII Connector Black 16
Ground Black 4 (-) OBDII Connector Black 16
SW CAN Lt.Green 1 Data OBDII Connector Black 16
CAN High Lt. Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
(+) 12V Red 16 (+) OBDII Connector Black 16
Ground Black 4 (-) OBDII Connector Black 16
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
(+) 12V Red/White 16 (+) OBDII Connector Black 16
Ground Black 4 (-) OBDII Connector Black 16
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
(+) 12V Red/White 16 (+) OBDII Connector Black 16
Ground Black 4 (-) OBDII Connector Black 16
GMC Sierra 2500/3500 2015-2016
Wire Information Connector Information
Chevrolet Tra x 2013-2016
GMC Canyon 2015-2016
GMC Sierra 1500 2014-2016
Chevrolet Tahoe 2015
Firmware GM10 Range Extender Ready (RXT) Installation:
Vehicle Wiring Reference Chart
Wire colors should only be used as a reference. You should always test a wire's function and pin location before
connecting to it.
Rev.: 20 701 821
Page 9
© 2017 Directed. All rights reserved.
Page 10
Platform: DBALL2
Function Color Pin Polarity Location Color Pins
SW CAN Dk. Green 1 Data OBDII Connector Black 16
CAN High Tan/Black 6 Data OBDII Connector Black 16
CAN Low Tan 14 Data OBDII Connector Black 16
(+) 12V Red/White 16 (+) OBDII Connector Black 16
Ground Black 4 (-) OBDII Connector Black 16
SW CAN Green 1 Data OBDII Connector Black 16
CAN High Blue 6 Data OBDII Connector Black 16
CAN Low White 14 Data OBDII Connector Black 16
(+) 12V Red/White 16 (+) OBDII Connector Black 16
Ground Black 4 (-) OBDII Connector Black 16
Wire Information Connector Information
GMC Yukon 2015
GMC Terrain 2010-2017
Firmware GM10 Range Extender Ready (RXT) Installation:
Vehicle Wiring Reference Chart
Wire colors should only be used as a reference. You should always test a wire's function and pin location before
connecting to it.
Rev.: 20 701 821
Page 10
© 2017 Directed. All rights reserved.
Page 11
Platform: DBALL2
Firmware GM10 Range Extender Ready (RXT) Installation:
Rev.: 20 701 821
SmartStart/ 202 Installation NotesXL
Th solution offers t ( ) configuration options to control your system Kit ore Range Extender Ready ( ) wo 2 :DBALL RXT RF
both This section provides specific installation information for SmartStart and 202.SmartStart ( sold separately). XL
SmartStart Revision A
SmartStart is and not included. It be purchased separately.optional MUST
Configuration Wires (White & Brown or Blue)
Cut Brown or Blue Loop
OR
Page 11
DBALL/
2DBALL
CABLE
D2D (4 pins, white)
The modules must be connected in a specific order. Refer to the section for more information.Module Programming
4 pins
2 pins,
not used
SmartStart
LED
SmartStart Revision B
SmartStart is and not included. It be purchased separately.optional MUST
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
5 pins
DBALL/
2DBALL
CABLE
D2D (4 pins, white)
The modules must be connected in a specific order. Refer to the section for more information.Module Programming
4 pins
2 pins,
not used
THIS SIDE UP
LED
RF Kit
The 202 and antenna are not included and be purchased separately.optional XL MUST
DBALL/
2DBALL
XOVER
LED
4
XL202
Prog.
Button
4
Antenna
1. Use the D2D Crossover ( ) cable that is provided with 202, and the one in the package.XOVER XL NOT DBALL
2. The modules must be connected in a specific order. Refer to the section for more information.Module Programming
RF PKE& CombinationKit
Refer to the Passive Keyless Entry ( ) Installation Guide (N2102T) for detailed wiring information.PKE
RF PKE BT, & SmartStart CombinationKit
Refer to the Passive Keyless Entry ( ) Installation Guide (N2102T) for detailed wiring information.PKE
© 2017 Directed. All rights reserved.
Page 12
Platform: DBALL2
Firmware GM10 Range Extender Ready (RXT) Installation:
Module Programming
Refer to the Diagnostics section on page 16 for more information and for troubleshooting purposes.LED
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the 202 or SmartStart module to , it is important to ensure that the proper feature andXL DBALL
function programming is selected using Xpress (version 4. or higher). Visit www.directechs.com to download the latestVIP 5
version of the application.
Warning! To take advantage of advanced features, you must use Xpress 4.5 (and higher) or the Directechs Mobile app.VIP
Flashing a module using your computer:
1. Connect the interface module to your computer using the
XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and
select the button.Config for RXT
3. Follow the instructions to select your vehicle, installation
type, and configure your options.
4. Once you have configured the firmware options, click on the
FLASH button.
When the flashing operation is successful, you can proceed with the programming instructions below.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your oader3.XKL
2. Launch the Directechs Mobile app on your smartphone or
tablet.
3. Select and follow the on screenFLASH YOUR MODULE
instructions.
Rev.: 20 701 821
Page 12
SmartStart Installation
The module be disconnected from any power source before SmartStart canDBALL must
be connected to it. Failing to do so could damage .DBALL
a. To e nsure that the D2D communication between SmartStart and works properly, theDBALL
Gray wire must be connected to a ground source ( SmartStart), and the Brown or BlueRev B
loop must be cut ( SmartStart).Rev A
b. Do connect the 2-pin harness (on SmartStart). Power and ground will be provided byNOT
the D2D connector.DBALL
Connect SmartStart to using the D2D port.DBALL
OR
XL202 Installation
Connect 202 to using theD2D port.XL DBALL
Connect the 10-pin 2-pin harnesses to, 1 and 14-pin
1
2
DBALL, then w .ait until the turns solid redLED ON
1
5 times on the programming buttonPress then the key to theturn IGN
position.
SmartStart
XL202
D2D
10-pin
st
rd
3
14-pin
12-pin
nd
2
&
Press X5
Key IN
D2D
D2D
10-pin
10-pin
&
OFF
Solid
IGN
START
The orange for 3 seconds .LED turns solid , then shutsON OFF
3
You have successfully completed the module programming sequence.
&
Solid x3 Secs Off
© 2017 Directed. All rights reserved.
Page 13
Platform: DBALL2
Firmware GM10 Range Extender Ready (RXT) Installation:
Rev.: 20 701 821
Page 13
Module Reset
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed
to the module using the web config tool will not be affected.
14-pin
12-pin
nd
2
rd
3
1
If required for your installation, connect the 10-pin & 12-pin
harnesses to the module Press hold the rogramming. and p
button, then connect the 14-pin harness to the module.
D2D
10-pin
st
1
th
4
Wait 3 seconds until the orange then release theLED turns solidON
2
p The turns solid red.rogramming button. LED ON
& &
Solid
Release
Solid
Hard Reset
Warning gainst xecuting a Hard Reset!AE
A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such
as and D2D options) may have to be reconfigured. See the section of this guide.RFTD Feature & Option List
1
2
If required for your installation, connect the 10-pin & 12-pin
harnesses to the module Press hold the rogramming. and p
button, then connect the 14-pin harness to the module.
Wait 3 seconds until the orange aitLED turns solid , and w 10 more secondsON
until the andLED starts to flash orange red.
D2D
10-pin
st
1
th
4
2
nd
14-pin
rd
3
Solid
12-pin
&
Flashes
3
Release the programming button. The turns solid red.LED ON
Release
&
Solid
© 2017 Directed. All rights reserved.
Page 14
Feat. Operation Flashes/Option Description
1. No RF
Output*
Module is c onnected to a remote starter using a s tandard ins tallation.
2. RFTD Output Module is connect ed to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartStart us ing an RSR or RXT installation (when available).
1. Drive r
priority*
Unlock s only the driver door when t he button is first pressed, and unloc ks all doors when it is
pressed a second time within 5 seconds.
2. All Unlocks all doors when the button is first pressed.
1. Disabl ed* No act ion.
2. Enabled for
Windows
Module will perform windows roll up upon lock c ommand.
3. Enabled for
Windows and
Sunroof
Module will perform windows roll up and close s unroof upon lock command.
1. Disabl ed* No operation.
2. Enabled W hen the feature is enabled, it will ac tivate the Heated Seat s and heated steering wheel.
1. 32°F (0°C)*
When Heated Seats or Defroster feature is enabled, it will activate the feature upon remote start
when temperature is below 32 °F (0 °C).
2. 23°F (-5°C)
When Heated Seats or Defroster feature is enabled, it will activate the feature upon remote start
when temperature is below 23 °F (-5 °C).
3. 41°F (+ 5°C)
When Heated Seats or Defroster feature is enabled, it will activate the feature upon remote start
when temperature is below 41 °F (5 °C).
4. Always ON When Heated Seats or Defroster feature is enabled, it will activate the feature at any temperature.
1. Disabled
The OEM alarm will not be c ontrolled by the int erface upon remote st art. No disarm or arm
command will be ex ecuted at the beginning or end of the sequenc e; it must be controlled by the
Remote Starter.
2. Safelock
Smart OEM Alarm Control will behave lik e a standard Safeloc k feature on a remot e starter. It will
unlock at the beginning of t he sequenc e, and relock after start and s hutdown.
3. Enable d*
Smart OEM Alarm Control will s ynchronize with the OEM alarm so that it will disarm and rearm the
vehicle in the remote start sequence, only when required. Smart OEM Alarm Control will monitor
the alarm and door loc k stat us to detect if the disarm or rearm is required. If the vehicle is unlocked
or is not equipped with factory alarm, the disarm/ rearm will not be executed.
Smart OEM Alarm
Control
6
Heated
Seats/Defroster
Temperature Control
5
* Default Option
RF TD Out put Ty pe1
Unlock Driver Priority
4
Comfort Closure with
Lock
3
2
Heated Seats
Platform: DBALL2
Firmware GM10 Range Extender Ready (RXT) Installation:
Rev.: 20 701 821
Page 14
Feature Option List&
It is recommended to configure all features and options listed below thethe using configuration tool found on the module flashing page
on www.directechs.com. The web offers more options such as ; however, manual configuration of the features is possible usingRSR
the information on this page.
© 2017 Directed. All rights reserved.
Page 15
Platform: DBALL2
Firmware GM10 Range Extender Ready (RXT) Installation:
Feature Programming
To enter feature programming routine
-
Turn t , thenhe ignition .ON OFF
-
Within 5 seconds, press and the rogramming button turns after 3 seconds . Release theHOLD LED ONp until the orange ( )
Programming button.
-
The to indicate the feature number is 1. After a short delay, the flashes rapidly to indicateLED LEDwill flash green once slowly red
the current option of feature 1 . repeat(i.e. 1x green followed by 1x red indicates feature 1 is set to option 1) The flashing sequence will
until .a new command is entered
Changing feature options
-
Press the arm or disarm button on aftermarket transmitter to change the option of the selected feature.lock/ unlock/
-
The flashes rapidly the number of times equal to the current option number. After a short delay, the flashes green slowlyLED LEDred
the number of times to indicate the current feature. repeat until .The flashing sequence will a new command is entered
Accessing another feature
-
Press and release the programming button a number of times to advance from the current feature to the next desired feature.
-
The flashes green slowly the number of times equal to the feature number. After a short delay, the flashes red rapidly toLED LED
indicate the current option of the current feature. repeat until .The flashing sequence will a new command is entered
When the maximum number of features or options is reached, the will start flashing again from the first feature or option.LED
Once a feature is programmed
-
Other features can be programmed.
-
The feature programming can be exited.
Programming
Rev.: 20 701 821
Page 15
Button
Exiting feature programming
-
No activity for 30 seconds; after 30 seconds, the will turn orange for 2 seconds to confirm the end of the programmingLED ON
sequence.
OR
-
Press and the programming button for 3 seconds. After 3 seconds, the will turn orange for 2 seconds to confirm theHOLD LED ON
end of the programming sequence.
© 2017 Directed. All rights reserved.
Page 16
LED Description Troubleshooting
Module has no power.
Make sure the D2D harness is c onnected or that the 12
Volt is present between the red and black wires. If the
12 Volt is present, the module may be defective.
Waiting to begin t he programming sequence.
Ensure the correct programming procedure is being
followed.
Initialization failed.
Reset the module and c omplete the programming again.
If the is sue pers is ts, please contact Technical Support.
Transponder functions were skipped.
(If compatible) when RXT mode is not desired or
convenience features are needed, please reset and
reprogram the module.
All required CAN networks has been detected. Normal operation.
1 of 2 CAN networks has been detected. Normal operation
Key2GO initiated.
Pleas e follow the steps indicated in “Module
programming” to complete the Key2GO programming.
Module was success fully programmed with all functions. Normal operation
Module was success fully programmed without
transponder functions.
Normal operation.
CAN2 not detected.
Check the CAN2 Orange/Green and Orange/Brown wire
connections. W ake up the data bus by turning the
ignition on and try again. If your installation does not
require this connection, skip this step by pressing the
programming button 5 times.
J1850 not detected.
Check the J1850 wire connection. W ake up the data bus
by turning the ignition on and try again.
CAN1 not detected.
Check the CAN1 Tan and Tan/Black wire connections.
Wake up the data bus by turning the ignition on and try
again. If your installation does not require this
connection, skip this step by pressing the programming
button 5 times.
Bypass data not detected.
Check the bypass line connection. If more than one wire
is used, make sure they are not inverted. Ensure the
vehicle s till operates correctly using the factory key.
Bypass processing error.
The bypass calculation failed. Reset the module and try
again. If the condition persists, please contact Technical
Support.
ISO 1 not detected.
The Yellow/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts )" to check the c onnections.
ISO 2 not detected.
The Orange/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts )" to check the c onnections.
MUX not detected.
The Violet/Green or Violet/Brown wire did not detect the
expected voltage value. Refer to "Installation (wiring
diagrams & vehicle wiring reference charts)" to c heck
the connections.
Module Programming
Module Programming - Error Codes
Platform: DBALL2
Firmware GM10 Range Extender Ready (RXT) Installation:
LED Diagnostics & Troubleshooting
Off
Solid red
Flashes red
& green
Solid orange
Flashes
green
Flashes
orange
Flashes
orange
slowly
Solid green
x 3 secs
Solid orange
x 3 secs
Rev.: 20 701 821
Page 16
Flashes red
x 1
Flashes red
x 1
Flashes red
x 2
Flashes red
x 3
Flashes red
x 4
Flashes red
x 5
Flashes red
x 6
Flashes red
x 7
© 2017 Directed. All rights reserved.
Page 17
Platform: DBALL2
LED Description Troubleshooting
OBDII feature is not s upported.
The diagnostic data bus was not detected, therefore the
SmartStart features will be limited.
Ground W hen Running (Stat us) command received. The module has initialized the remote start sequence.
Ignition ON command received.
The module has received the Ignition ON command and is
processing the remote start sequence.
Start ON command received.
The module has received the Start ON command and is
processing the remote start sequence.
PTS shutdown error.
The PTS output from the module was not activated due to
safety protection.
CAN bus incorrectly detected.
Verify the CAN1 and CAN2 connections. Refer to “Installation
(wiring diagrams & vehicle wiring reference c harts)” to c heck
the connections.
LOCK command received.
UNLOCK command received.
TRUNK c ommand received.
AUX1 command received.
AUX2 command received.
AUX3 command received.
Takeover successful. Normal operation.
Runsafe was not dis abled.
No UNLOCK command was received prior to opening the
door, or the 45 second timer expired in takeover mode.
Brake was not detected.
The brakes were not detected, which prevents the system
from shutting down the vehicle.
Smart key was not detected.
The smart key was not detected, which prevents the s ystem
from shutting down the vehicle.
Speed was detected.
The vehicle was detected as moving, which prevents the
system from shutting it down.
External module synchronization
Commands
Activation Ground When Running (Status)
If the bypass module fails to flash, it did not receive the
signal. Commands can c ome from RF or D2D.
Shutdown codes
Firmware GM10 Range Extender Ready (RXT) Installation:
(Flashes red,
red then
orange) x 10
Flashes
green
Flashes red
& orange
Flashes
green
quickly
Flashes red
x 10
Flashes red
x 21
Flashes
orange x 1
Flashes
orange x 2
Flashes
orange x 3
Flashes
orange x 4
Flashes
orange x 5
Flashes
orange x 6
Flashes
green x 1
Flashes red
x 1
Rev.: 20 701 821
Page 71
Flashes red
x 2
Flashes red
x 3
Flashes red
x 4
© 2017 Directed. All rights reserved.
Page 18
Platform: DBALL2
Firmware GM10 Range Extender Ready (RXT) Installation:
Rev.: 20 701 821
Page 81
Limited Consumer WarrantyOne Year
For a period of from the date of purchase of a Directed Electronics remote start or security product, DirectedONE YEAR
Electronics. (“ ”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece,theDIRECTED
security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material
under normal use, provided the following conditions are met: the Part was purchased from an authorized dealer;DIRECTED
and the Part is returned to , postageprepaid, along with a clear, legible copy of the receipt or bill of sale bearing theDIRECTED
following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete
product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its
intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or
other causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW EXCEPT AS STATED ABOVE ALL WARRANTIES INCLUDING,,,
BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY,, ,
FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL
PROPERTY ARE EXPRESSLY EXCLUDED AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY,;
PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY OBLIGATION OR LIABILITY IN CONNECTION WITH ITS,
PRODUCTS DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FORANY AND ALLACTS OF.
THIRD PARTIES INCLUDING DEALERS OR INSTALLERS DIRECTED IS NOT OFFERING GUARANTEE OR.A
INSURANCE AGAINST VANDALISM DAMAGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS,, , ,
AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER INCLUDING WITHOUT LIMITATION,,
LIABILITY FOR THEFT DAMAGE OR VANDALISM IN THE EVENT OF CLAIM OR DISPUTE INVOLVING,, . A A
DIRECTED OR ITS SUBSIDIARY THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF,
CALIFORNIA CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE.
DISPUTE THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED.
TO THE AUTHORIZED DIRECTED DEALER PURCHASE PRICE OF THE PART DIRECTED SHALL NOT BE’S .
RESPONSIBLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL,,
DAMAGES INCIDENTAL DAMAGES DAMAGES FOR THE LOSS OF TIME LOSS OF EARNINGS COMMERCIAL,, ,,
LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE THE,.,
MANUFACTURER DOES OFFER LIMITED WARRANTY TO REPLACE OR REPAIRAT DIRECTED OPTION THEA’S
PARTAS DESCRIBEDABOVE.
This warranty only covers Parts sold within the UnitedStates of America and Canada. Parts sold outside of the United States of
America or Canada are sold “ - ” and shall have , expressor implied. Some states do not allow limitationsAS IS NO WARRANTY
on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty
gives you specific legal rights and you may also have other rights that vary from State to State. does not and hasDIRECTED
not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.
For further details relating to warranty information of Directed products, please visit the support section of ’sDIRECTED
website at: www.directed.com
920-10012-01 2013-07
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select
vehicle list upon completion of compatibility testing.Visit website for latest vehicleapplication guide. : Under noDISCLAIMER
circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any
consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor
will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data
bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this
product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes
any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876
B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1;
7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent:
2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European
Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
© 2017 Directed. All rights reserved.
Page 19
Quick Reference Guide
DBALL2- Range Extender Ready (RXT) InstallationGM10
© 2017 Directed. All rights reserved.
Range Extender Ready ( ) is used to amplify the distance coveredRXT
by factory remote starters, which are built into the of the vehicle.BCM
The interface connects to the vehicle and uses the same codes as the
factory remote to remote start the vehicle. The runtime and features are
identical to the ones for the remote starter. Some of theOEM
advantages of are greater distance coverage and 2-wayRXT
compatibility.
Range Extender Ready ( )RXT
Command Engine Result
Start NOT running. The engine will be s tarted (runtim e 10 minutes).
Start Running. The engine will be stopped.
The following table describes the behavior of the vehicle in relation to the RXT
feature. The following commands are performed on the aftermarket remote.
Runtime
T equivalent to the amount set for the ,he runtime is remote starter which is 10OEM
minutes. A maximum of 2 remote start can be performed between ignition cycle .ss
Runtime Reset
Tshe Runtime Reset feature allow the user to increase the runtime duration for a
maximum of 10 minutes. This can only performed per remote start.ONCE
RXT Operations
Button(s)
Actions
Press & hold for 1 second to lock.
Press & hold for 1 second to unlock.
Press & hold for 1 second to remot e
start.
Press & hold for 5 seconds to activate
the trunk release (optional).
Press once, then t o ac tivate the
rear hatc h/t ail glass release (optional).*
Press 3 times, then to act ivate
the panic mode.
Press once, then t o res et the
remote starter runtime.
List of Available Commands
x1 +
x3 +
x1 +
* This output is configurable. see your authorized installation center for more
information.
Note that the information below is for Viper, Clifford and Python models. Icons and
commands may differ depending on the remote brand and model purchased. Refer
to your authorized installation center for more information.
Note: Due to limitations, the remote starter will not activate if “CheckOEM
Engine” indicator or (Diagnostic Trouble Code) is present, or if the hood isDTC
open or if 2 remote start were done without inserting the key to ignition .ON
Page 20
Quick Reference Guide
DBALL2- Range Extender Ready (RXT) InstallationGM10
© 2017 Directed. All rights reserved.
Notes
SmartStart Compatible
This system is compatible with Directed SmartStart 3.0. For
a complete list of supported features, please visit
www.mysmartstart.com.
What is SmartStart?
Now you can remote start, lock and unlock your car just by pushing a button on
your smartphone; using the SmartStart App from Directed, the leader in vehicle
security and remote start. The simple graphical interface gives you control over the
following features of your installed remote start or security with remote start system:
Lock/Arm
Unlock/Disarm
Remote Car Starter
Trunk Release
Panic
Aux Channels
You can also control multiple vehicles – great for families – and assign more than
one user to control a vehicle. It's easy with SmartStart!
But, this is only the beginning! SmartStart is loaded with additional features
including tracking, SmartSchedule, vehicle status, roadside assistance, homeGPS
control, parked car finder and more.
3.0 enables a "Cloud-Connected Car" like never before, providing an entirely new
level of 2-way interaction with your vehicle. Connectivity is managed through the
Directed Cloud Services ( ) network linking car, app, end user, and the Internet.DCS
For more information, visit www.mysmartstart.com.
Loading...