XPR Access DINB100-SA v2 User Manual

www.xprgroup.com

1

Standalone Biometric Reader

EN

DINB100SA v2

USER’S MANUAL

v. c3

www.xprgroup.com

2

1. INTRODUCTION

2. MOUNTING

3. SPECIFICATIONS

4. APPLICATION DIAGRAM

5. RECOMMENDED SWIPING TECHNIQUE

6. INDICATION

7. WIRING

8. ADDING ADMIN FINGER

9. PAIRING  BIOMETRIC READER AND REMOTE RELAY UNIT

Pairing dinb100-sa with dinrtt

Pairing dinb100-sa with rtt

Pairing dinb100-sa with ru2

10. ADMINISTRATOR PROGRAMMING

Add inger relay 1

Add inger relay 2

Add inger relay 1&2

Delete inger

Delete all ingers

Change admin inger

Change installer inger

Administrator programming block diagram

11. INSTALLER PROGRAMMING

Set relay 1 time

Set relay 2 time

Buzzer on/o

Backlight on/o

Installer programming block diagram

12. ADMINISTRATOR PROGRAMMING BY KEYPAD

13. INSTALLER PROGRAMMING BY KEYPAD

3
3
4
4
4
4
5
5

6
6
6
6

7
7
7
7
7
8
8
8
9

10
10
10
10
10
11

12

14

CONTENS

www.xprgroup.com

3

1. INTRODUCTION

MAINTENANCE

WARNING!

2. MOUNTING

RECOMMENDATIONS

NOTES

DINB100SA v2 is access control ingerprint reader designed for easy management of the users and coniguration. The
scanner is made with advanced capacitive sensing technology that provides some advantages over optical solutions like:

- making almost impossible to make fake copy of the users ingers

- same performance in the dierent light conditions

- good reading of ingers with stains from daily jobs
Built in strong scanning and matching algorithm provides excellent tolerance in the way inger is swiped over the sensor
reducing to minimum the need to repeat inger swiping at the sensor.
The reader can store up to 100 inger templates. One template is reserved for User manager (Administrator), one
template is reserved for Reader coniguration (Installer) and up to 98 templates are for Users.

No special or periodic maintenance is required. If cleaning is needed, use soft wet cloth and wipe gently the dirt. Do not use
chemicals and materials that can scratch the sensor.

Do not touch the sensor with other objects than inger. Do not pour or splash with water or other liquids. When painting or
construction work is ongoing in the area around the reader, protect the reader sensor area from possible damages and paint.
If reader is to be dismounted or relocated, call authorized installer for the job. Disposal of this product must be handled
according to all national laws and regulations.

Consult with installer about safety level of the installation. There are devices with relays compatible with this reader that can
increase the security of the system if needed. One or two enrolled ingers are enough for one user. Ask the installer before he
leaves the site to enroll your inger as administrator.

The Reader is using physical roughness of the ingerprint to scan the inger. Some of the users may have very lat ingertips,
making diicult for the sensor to recognize correctly the ingerprint. In most cases, these are children and older persons. To
solve this problem, do the following:

1. Try with dierent user’s ingers to ind the “best” inger.

2. Check with the installer other models of the reader with added card reader or keypad for other type of access.

Do not install the device and cabling close to a source of strong electro-magnetic ields like radio-transmitting antenna.
Do not place the device near or above heating equipments.
If cleaning, do not spray or splash water or other cleaning liquids but wipe it out with smooth cloth or towel.
Do not let children touch the device without supervision.
Note that if the sensor is cleaned by detergent, benzene or thinner, the surface will be damaged and the ingerprint can’t be entered.

The operating temperature of the product is between -20ºC - + 50ºC. If the reader is installed in an environment where the
temperature can drop below -10ºC or/and if the sensor could only be exposed to direct sunlight, it is strongly recommended
to install the reader inside a third party sealed wall mount box (itted with additional heater if very low temperature) to keep
a constant sensor level performance. XPR™ cannot guarantee the functionality of the product if measures and advice before
are not followed.
It is also strongly recommended to use double technology biometric readers when use outdoor to oer irst higher security
but also the possibility to use dierent readers depending on users.

www.xprgroup.com

4

4. APPLICATION DIAGRAM

6. INDICATION

3. SPECIFICATIONS

5. RECOMMENDED SWIPING TECHNIQUE

Fingerprint Capacity:
Output:
Push Button Input:
Door Open Time:
Entry Mode:

Programming:
Admin/Installer Fingers:
Backlight ON/OFF:
Buzzer ON/OFF:
Firmware upgrade:
Current Consumption:
Power Supply:
Indication:
IP Factor:
Storage/Operating Temperature :
Storage/Operating Humidity:
Dimensions(mm):

98 templates
1 x Relay (2 A /24V AC/DC)
Yes
Pulse (1 to 30 seconds) or Toggle(ON/OFF)
Finger (basic installation)

Finger or Card (when used with card reader DIN Card reader)
Finger or PIN code (when used with keypad DINPADM)

By swiping
1 Administrator and 1 Installer Finger
Yes
Yes
via RS485 converter and windows application
100 mA max.
914 V DC
Tricolor Status LED
IP40

-20°C to +50°C
5% to 93% RH without condensation
80 x 80 x 9

DINB100-SA v2

Follow the below instructions for correct inger swiping. Starting from the irst inger joint,
place the selected inger on the swipe sensor and move it evenly towards oneself in one
steady movement.
Result:
For a valid swipe: Tricolour Status LED turns green + OK Beep(short + long beep)
For an invalid or misread swipe: Tricolour Status LED turns red + Error Beep ( 3 short beeps)

Tricolor Status LED

Green - Access Granted

Red - Access denied

Orange - Idle Mode

OK Beep - short + long beep

Error Beep - 3 short beeps

Swipe Finger - 2 short beeps

www.xprgroup.com

5

7. WIRING

8. ADDING ADMIN FINGER

1. Close the jumper on the back of the device.

2. Reset the Power of the device.

3. Wait for One long + multiple short beeps

4. Open the jumper. (short beeps will stop)

5. Wait for about 15 seconds for the LED to blink in Orange.

6. Swipe the Master inger min.6 times. (Until Ok Beep)

Warning: This procedure also deletes all the users and the installer inger.
Warning: This procedure will unpair the connected relay unit (RTT, DINRTT or RU2)

NC

C

NO

12V

GND

B

PB

A

GND

tamp

tamp

Relay Output

1N4007

Electric Door Strike

(DC powered)

+

-

Jumper (Adding Master Finger)

12 VDC

+

-

12V

GND

B

PB

A

GND

tamp

tamp

PB

tamp

tamp

C

NO

Alarm

12V

GND

Power Supply

(9-14V DC)

GND
B

+12V

PB
GND

A

Rs485

Push Button

Tamper

tamp
tamp

NC

C

NO

NC

C

NO

Connection to additional

card reader or keypad

DINB100-SA v2

12/24V AC/DC

12V

GND

B

A

DINB100-SA

x 6

www.xprgroup.com

6

9. PAIRING - BIOMETRIC READER AND REMOTE RELAY UNIT

If secure installation is needed, the reader can be connected to remote relay unit at secured area, which also can play the role of
request-to-exit push button. Follow the instructions bellow to pair(couple) both devices or refer to the Remote Relay’s Manual.

Pairing DINB100-SA with DINRTT

Pairing DINB100-SA with RTT

Pairing DINB100-SA with RU2

1. Close the Jumper. DINRTT beeps continuously and
the red led blinks.

2. Open the Jumper

3. Wait for Beep + OK Beep (short + short + long beep)

After the OK beep, the coupling is done.

1. Put Dipswitch No.1 to position ON. RTT
beeps continuously and the red ledblinks.

2. Put Dipswitch No.1 to position OFF.

3. Wait for Beep + OK Beep (short + short +
long beep)

After the OK beep, the coupling is done.

1. Put the Jumper to closed position. RU2
beeps continuously and the red led blinks.

2. Put the Jumper to open position.

3. Wait for Beep + OK Beep (short + short + long
beep)

After the OK beep, the coupling is done.

Pb2

GND

Pb1

GND

Nc1

COM

No1

Nc2

COM

No2

A

B

Tamp

Tamp

Rs485

GND

+12V

GND

+12V

Exit Button

(NO)

1N4007

+

-

Rs485

A

B

12V

GND

B

A

+12V

GND

12 VDC

+

-

12 VDC

+

-

DINB100-SA v2

DINRTT

A

B

+12V

+12V

GND

GND

GND

Pb1

No1

COM

12

max. 50 meters

Rs485

A

B

12V

GND

B

A

+12V

GND

12 VDC

+

-

DINB100-SA

A

B

+12V

GND

1N4007

+

-

12 VDC

+

-

No

COM

RTT

12

ON

max. 50 meters

12 VDC

+

-

1N4007

+

-

Ru2

Violet

Pink

COMNO

A (RS485)

B (RS485)

+12V

GND

GND

+12V

DINB100-SA v2

1

2

max. 50 meters

Warning: Changing the ADMIN inger will also unpair the remote relay unit.

www.xprgroup.com

7

10. ADMINISTRATOR PROGRAMMING

ADD Finger Relay 1 (Finger that will activate relay 1)

ADD Finger Relay 2 (Finger that will activate relay 2)

ADD Finger Relay 1&2 (Finger that will activate relay 1&2)

Use point ingers as Administrator and Installer. You can use the other ingers as access ingers.
Administrator inger is enrolled at the end of the system installation. Initial enrollment of the Admin inger is described in
installer manual.

Action Finger Backlight Buzzer Sound

Swipe Admin Finger 1 time

x 1

slow blinking

short beep

Wait 5 seconds (until fast blinking) short beep

Swipe User Finger min. 6 times

(until short + long beep)

x 6

fast blinking

short + long beep

Action Finger Backlight Buzzer Sound

Swipe Admin Finger 2 times

x 2

slow blinking

short beep

Wait 5 seconds (until fast blinking) short beep

Swipe User Finger min. 6 times

(until short + long beep)

x 6

fast blinking

short + long beep

Action Finger Backlight Buzzer Sound

Swipe Admin Finger 3 times

x 3

slow blinking

short beep

Wait 5 seconds (until fast blinking) short beep

Swipe User Finger min. 6 times

(until short + long beep)

x 6

fast blinking

short + long beep

or

or

or

Present card/tag 1 time

x 1

fast blinking short + long beep

Present card/tag 1 time

x 1

fast blinking short + long beep

Present card/tag 1 time

x 1

fast blinking short + long beep

Relay 2 is available if the reader is used with remote relay unit with 2 relays(DINRTT and RU2). Consult the installer if Relay 2 is available in your system.

Relay 2 is available if the reader is used with remote relay unit with 2 relays(DINRTT and RU2). Consult the installer if Relay 2 is available in your system.

www.xprgroup.com

8

DELETE Finger

DELETE ALL Fingers and Cards

CHANGE ADMIN Finger

CHANGE INSTALLER Finger

Action Finger Backlight Buzzer Sound

Swipe Admin Finger 4 times

x 4

slow blinking

short beep

Wait 5 seconds (until fast blinking) short beep

Swipe User Finger

x1

fast blinking

short + long beep

Action Finger Backlight Buzzer Sound

Swipe Admin Finger 4 times

x 4

slow blinking

short beep

Wait 5 seconds (until fast blinking)

slow blinking

short beep

Swipe Admin Finger 2 times

x2

fast blinking

multiple beeps

Action Finger Backlight Buzzer Sound

Swipe Admin Finger 5 times

x 5

slow blinking

short beep

Wait 5 seconds (until fast blinking)

slow blinking

short beep

Swipe NEW Admin Finger

min.6 times

x6

fast blinking

short + long beep

Action Finger Backlight Buzzer Sound

Swipe Admin Finger 6 times

x 6

slow blinking

short beep

Wait 5 seconds (until fast blinking)

slow blinking

short + long beep

Swipe NEW Installer Finger

min.6 times

x6

fast blinking

3 short beeps

or

Present card/tag 1 time

x 1

fast blinking short + long beep

CONNECTING DINB100 WITH DINMTPX PROXIMITY READER

Connect both devices with the cable provided.
The proximity reader will be powered via that
cable. No extra power supply for the proximity
reader is needed. Once connected, no further
settings are needed.

www.xprgroup.com

9

Administrator Programming block diagram

Swipe the ADMIN Finger 1 to 6 times depending of the desired menu

ADD Finger

Relay 1

(on board)

1 swipe

ADD Finger

Relay 2

(remote)

ADD Finger

Relay 1&2

DELETE FINGER

Change

ADMIN
Finger

Enroll

INSTALLER

Finger

2 swipes 3 swipes

4 swipes

5

swipes

6 swipes

Wait

5 seconds

(until fast blinking)

SWIPE

new finger

min. 6 times

or

present

card/tag

SWIPE

already enrolled

finger

1 time

or

present

card/tag

SWIPE

new finger

min. 6 times

or

present

card/tag

SWIPE

new finger

min. 6 times

or

present

card/tag

SWIPE

ADMIN finger

2 times

to

DELETE ALL

SWIPE

new ADMIN

FINGER

min. 6 times

SWIPE

new

INSTALLER

FINGER

min. 6 times

END END

END

END

END

END END

Only in combination

with DINRTT and RU2

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

www.xprgroup.com

10

11. INSTALLER PROGRAMMING

Set Relay 1 Time

Set Relay 2 Time

BUZZER ON/OFF

BACKLIGHT ON/OFF

Action Finger Backlight Buzzer Sound

Swipe Installer Finger 1 time

x1

slow blinking

short beep

Wait 5 seconds (until fast blinking) short beep

Swipe the INSTALLER Finger

and start counting seconds

x1

fast blinking

beeps on 1 second

Swipe the INSTALLER Finger

to stop or wait 30 seconds to

put the relay in toggle mode

x1

fast blinking short + long beep

Action Finger Backlight Buzzer Sound

Swipe Installer Finger 2 times

x2

slow blinking

short beep

Wait 5 seconds (until fast blinking) short beep

Swipe the INSTALLER Finger

and start counting seconds

x1

fast blinking

beeps on 1 second

Swipe the INSTALLER Finger

to stop or wait 30 seconds to

put the relay in toggle mode

x1

fast blinking short + long beep

Action Finger Backlight Buzzer Sound

Swipe Installer Finger 3 times

x3

slow blinking

short beep

Wait 5 seconds (until fast blinking) short beep

Swipe Installer Finger

x1

fast blinking

short + long beep

Action Finger Backlight Buzzer Sound

Swipe Installer Finger 4 times

x4

slow blinking

short beep

Wait 5 seconds (until fast blinking) short beep

Swipe Installer Finger

x1

fast blinking

short + long beep

Relay 2 is available if the reader is used with remote relay unit with 2 relays(DINRTT and RU2). Consult the installer if Relay 2 is available in your system.

www.xprgroup.com

11

Installer Programming block diagram

Swipe the Installer Finger 1 to 4 times depending of the desired menu

Set

RELAY 1

Time

(on board)

1 swipe

Set

RELAY 2

Time

(remote)

BUZZER

ON/OFF

BACKLIGHT

ON/OFF

2 swipes 3 swipes

4 swipes

Wait

5 seconds

(until fast blinking)

END END

END

END

Swipe the Installer Finger

and start counting seconds

Swipe the Installer Finger

to put the Buzzer ON/OFF

Swipe the Installer Finger

to stop or wait 30 seconds

to put the relay in toggle

ON/OFF mode

Only in combination

with DINRTT and RU2

Swipe the Installer Finger

and start counting seconds

Swipe the Installer Finger

to stop or wait 30 seconds

to put the relay in toggle

ON/OFF mode

Swipe the Installer Finger

to put the Backlight

ON/OFF

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

www.xprgroup.com

12

12. ADMINISTRATOR PROGRAMMING BY KEYPAD

Programming by keypad can be done only if the DINB100SA V2 reader is connected to keypad DINPADM as shown
in the pictures bellow. The connection is done by the cable provided with the biometric reader. Once connected,
the keypad must be put in slave mode.

Connect both devices with the cable provided.

Put the keypad in slave mode:

Press B (3 seconds) + 000000
Press 0
Press 2
Press A to exit

Reset the device

Note: In some previous versions of our keypads,
you can enter the menu only by pressing B +

000000. Please refer to the Keypad’s Manual.

www.xprgroup.com

13

ADMINISTRATOR PROGRAMMING BY KEYPAD

Note: Entering this menu is done by
admin PIN Code. You can not enter
with Admin Finger.

Note: The Fingerprint can be
deleted by keypad, only if it is
enrolled with keypad.

Example 1: Add user inger to Relay1 - Press 1234 + A + 1 + 1 + 1 + 01 + A + Enroll inger 6 times. 0A to exit.
Example 2: Add user PIN 147 to Relay2 - Press 1234 + A + 1 + 2 + 2 + 02 + A + 147 + A. 0A to exit.

ENTER ADMIN CODE

default: 1234+A

ADD

User

MENU

Press 0A to exit the Menu

Press “A”

DELETE

User

ENROLL

Admin Finger

or PIN Code

ENROLL

Installer Finger

or PIN Code

FINGER
Location

01-97

Press “A”

ENROLL

Finger

Swipe

the finger

min.

6 times

PIN Code

Location

01-97

Press “A”

PRESS

the

PIN Code

1 to 8

digits

Press “A”

ENROLL

Finger

Swipe

the finger

min.

6 times

ENROLL

Finger

Swipe

the finger

min.

6 times

PRESS

the

PIN Code

1 to 8

digits

PRESS

the

PIN Code

1 to 8

digits

Press “A”Press “A”

PIN Code

Location

FINGER
Location

1

2

DELETE

ALL

Users

3

4

5

01-97 01-97

ADD

Finger

1

ADD

PIN Code

2

Press “A”

Press “A” Press “A” Press “A” Press “A”

DELETE

PIN Code

DELETE

Finger

RELAY 1

(on board)

RELAY 2

(remote)

RELAY

1 & 2

3

CONFIRM

ADD

Finger

ADD

PIN Code

ADD

Finger

ADD

PIN Code

7

Press 0A to exit the Menu

Exit

multiple beeps

2

2

2

2

1

1

1

1

x 6

x 6

x 6

Press “A”

www.xprgroup.com

14

13. INSTALLER PROGRAMMING BY KEYPAD

Note: Entering this menu is done by
installer PIN Code. You can not enter
with Installer Finger.

Example: Change relay1 time to 2 seconds - 5678 + A + 1 + 02 + A.

ENTER INSTALLER CODE

default: 5678+A

Set Relay 1

TIME

(on board)

MENU

1

Set Relay 2

TIME

(remote)

2

Press 0A to exit the Menu

Press

01 to 30 for

time in seconds

or

00 for toggle

(ON/OFF) Mode

Backlight

ON/OFF

Buzzer

ON/OFF

3

4

Press

01 to 30 for

time in seconds

or

00 for toggle

(ON/OFF) Mode

0 = OFF

1 = ON

0 = OFF

1 = ON

Press “A”

Press “A”

Press “A” Press “A”

Press 0A to exit the Menu

www.xprgroup.com

15

www.xprgroup.com

16

This product herewith complies with requirements of EMC directive 2014/30/EU. In addition it complies with
RoHS2 directive EN50581:2012