XPR Access B100PROX-EH-SA v2, B100PROX-MF-SA v2 Installer Manual

B100PROX-EH-SA v2 B100PROX-MF-SA v2

Standalone Biometric Reader

1

INSTALLER’S MANUAL

v. c2

Contents

INTRODUCTION

MOUNTING

SPECIFICATIONS

APPLICATION DIAGRAM

RECOMMENDED SWIPING TECHNIQUE

INDICATION

WIRING

ADDING ADMIN FINGER

PAIRING - BIOMETRIC READER AND REMOTE RELAY UNIT

Pairing B100PROX-SA v2 with DINRTT

Pairing B100PROX-SA v2 with RTT

Pairing B100PROX-SA v2 with RU2

ADMINISTRATOR PROGRAMMING

ADD Finger Relay 1

ADD Finger Relay 2

ADD Finger Relay 1&2

DELETE Finger

DELETE ALL Fingers

CHANGE ADMIN Finger

CHANGE INSTALLER Finger

Administrator Programming block diagram

INSTALLER PROGRAMMING

Set Relay 1 Time

Set Relay 2 Time

BUZZER ON/OFF

BACKLIGHT ON/OFF

Installer Programming block diagram

2

3

4

5

..............................................................

...........................................................

.............................................................

....................................................................

...........................................

..............................................................

..............................

...........................................................

..............................................................

...........................................................

7 7 7 7 7 8 8 8

8

6 6 6

9 9 9

9 9

10

...........................................................

6

2

B100PROX-SA v2 is access control ﬁngerprint reader designed for easy management of the users and conﬁguration. The scanner is made with advanced capacitive sensing technology that provides some advantages over optical solutions like:

- making almost impossible to make fake copy of the users ﬁngers

- same performance in the diﬀerent light conditions

- good reading of ﬁngers with stains from daily jobs Built in strong scanning and matching algorithm provides excellent tolerance in the way ﬁnger is swiped over the sensor reducing to minimum the need to repeat ﬁnger swiping at the sensor. The reader can store up to 100 ﬁnger templates and 2000 cards. One template is reserved for User manager (Administrator), one template is reserved for Reader conﬁguration (Installer) and up to 98 templates are for Users.

This manual is used for both B100PROX-EH-SA (EM/HID Cards) and B100PROX-MF-SA (Mifare Cards).

INTRODUCTION

Consult with installer about safety level of the installation. There are devices with relays compatible with this reader that can increase the security of the system if needed. One or two enrolled ﬁngers are enough for one user. Ask the installer before he leaves the site to enroll your ﬁnger as administrator.

Do not touch the sensor with other objects than ﬁnger. Do not pour or splash with water or other liquids. When painting or construction work is ongoing in the area around the reader, protect the reader sensor area from possible damages and paint. If reader is to be dismounted or relocated, call authorized installer for the job. Disposal of this product must be handled according to all national laws and regulations.

RECOMMENDATIONS

NOTES

The Reader is using physical roughness of the ﬁngerprint to scan the ﬁnger. Some of the users may have very ﬂat ﬁngertips, making diﬀicult for the sensor to recognize correctly the ﬁngerprint. In most cases, these are children and older persons. To solve this problem, do the following:

1. Try with diﬀerent user’s ﬁngers to ﬁnd the “best” ﬁnger.

2. Check with the installer other models of the reader with added card reader or keypad for other type of access.

MAINTENANCE

No special or periodic maintenance is required. If cleaning is needed, use soft wet cloth and wipe gently the dirt. Do not use chemicals and materials that can scratch the sensor.

WARNING!

3

MOUNTING

100 mm

94 mm

30 mm

Cable

Ø6.0

30mm

MCD-MINI

Do not install the device and cabling close to a source of strong electro-magnetic ﬁelds like radio-transmitting antenna. Do not place the device near or above heating equipments. If cleaning, do not spray or splash water or other cleaning liquids but wipe it out with smooth cloth or towel. Do not let children touch the device without supervision. Note that if the sensor is cleaned by detergent, benzene or thinner, the surface will be damaged and the ﬁngerprint can't be entered.

If the biometric reader is installed and used outdoor, the reader MUST be ﬁtted with the MCD-MINI metal cover available in our accessories in order to protect the sensor from direct rainfall. The operating temperature of the product is between -20ºC - + 50ºC. If the reader is installed in an environment where the temperature can drop below -10ºC or/and if the sensor could only be exposed to direct sunlight, it is strongly recommended to install the reader inside a third party sealed wall mount box (ﬁtted with additional heater if very low temperature) to keep a constant sensor level performance. XPR™ cannot guarantee the functionality of the product if measures and advice before are not followed. It is also strongly recommended to use double technology biometric readers when use outdoor to offer first higher security but also the possibility to use different readers depending on users.

Fingerprint Capacity: Prox. cards Capacity: Card Type:

Output: Push Button Input: Door Open Time: Entry Mode: Programming: Master/Admin Fingers: Backlight ON/OFF: Buzzer ON/OFF: Firmware upgrade: Current Consumption: Power Supply: Indication: IP Factor: Storage/Operating Temperature : Storage/Operating Humidity: Dimensions(mm):

98 templates 2000 cards EM or HID compatible (125KHz) - B100PROX-EH-SA or Mifare (13,56 Mhz; Classic 1K & 4K, Ultralight, Desfire) - B100PROX-MF-SA 1 x Relay (2A/24V AC/DC) Yes Pulse (1 to 30 seconds) or Toggle(ON/OFF) Finger or Card By swiping 1 Administrator and 1 Installer Finger Yes Yes via converter and windows applicationRS485 150 mA max. 9-14 V DC Tricolor Status LED IP65

-20°C to +50°C 5% to 93% RH without condensation 100 x 94 x 30

4

SPECIFICATIONS

APPLICATION DIAGRAM

R

S485 (max. 50m)

DINRT T (Oponal)

2 Relay Remote Unit

and request-to-exit Buon

RTT (Oponal)

1 Relay Remote Unit

and request-to-exit Buon

RU2 (Oponal)

2 Relay Remote Unit

OR

Secured Area Outside

B100PROX-EH/MF-SA v2

Standalone Biometric Reader

MCD- MINI

(Oponal)

Metal Cover

NC COM

NO

Tamp

Blue

Yellow

Red

Black

Pink

Violet

Orange

Gray

White

PB

RS485

+

_

12VDC

POWER SUPPLY

+

_

NC

COM

GND (PB)

PB

+

_

Electro Magnetic Lock

Green

Blue

Yellow

Red

Black

Pink

Violet

Orange

Gray

White

Green

Colour

Connection

Tamper

12V DC

Red

Black

White

Yellow

Grey

NC COM

NO

GND

Green

Relay

(2A)

Push Button

Orange

Pink

Violet

Blue

Tamper

A (RS485)

B (RS485)

1N4001

Diode

12V DC GND

A B

+

-

+

_

12VDC

POWER SUPPLY

NO

COM

GND (PB)

PB

+

_

Blue

Yellow

Red

Black

Pink

Violet

Orange

Gray

White

Green

1N4001

Diode

Electric Strike

ON

1 2

ON

1 2

Adding Admin Finger

CARD Type

Dipswitch A: Card Type

ON: HID OFF: EM

ON

1 2

Dipswitch A Dipswitch B

Dipswitch B: Adding Admin Finger

ON

1 2

reader back view

Switch No. 2

B100PROX-SA

+12V GND NO COM

A

B

NC

PB1

TAMP TAMP

Relay

(2A)

RS 485

Power Supply

ON

1 2

Dipswitch A (sw. no.2)

Card Type

ON

1 2

Dipswitch B (sw. no.2)

Adding Master Finger

Push Button

ON: HID OFF: EM

5

Only in B100PROX-EH-SA v2

WIRING

Wiring B100PROX-SA with magnetic lock

Wiring B100PROX-SA with electric strike

DIPSwitch settings

6

ADDING ADMIN FINGER

1.Push dip switch no.2 in position ON.

2.Reset the Power of the device.

3.Wait for One long + multiple short beeps

4.Put the dip switch in position OFF. (short beeps will stop)

5.Wait for about 15 seconds for the LED to blink in Orange.

6.Swipe the Master ﬁnger min.6 times. (Until Ok Beep)

No.2

Warning: This procedure also deletes all the users and the installer ﬁnger. Warning: This procedure will unpair the connected relay unit (RTT, DINRTT or RU2)

x 6

ON

1 2

ON

1 2

Tricolor Status LED

- Access GrantedGreen

- Access deniedRed

- Idle ModeOrange

OK Beep - short + long beep

- 3 short beepsError Beep

Swipe Finger - 2 short beeps

INDICATION

Follow the below instructions for correct finger swiping. Starting from the first finger joint, place the selected finger on the swipe sensor and move it evenly towards oneself in one steady movement.

Result: For a valid swipe: Tricolour Status LED turns green + OK Beep(short + long beep) For an invalid or misread swipe: Tricolour Status LED turns red + Error Beep ( 3 short beeps)

RECOMMENDED SWIPING TECHNIQUE

12/24V AC/DC

B (RS485)

A (RS485)

1. Close the Jumper. DINRTT beeps continuously and the red led blinks.

2. Open the Jumper

3. Wait for Beep + OK Beep (short + short + long beep)

After the OK beep, the coupling is done.

P

B2

G

ND

PB1

G

N

D

NC1

COM

NO1

NC2

COM

NO2

A

B

T

A

MP

TA

M

P

R

S485

GND

+12V

GND

+12V

Exit Button

(NO)

1N4007

+

-

12 VDC

+

-

DINRT T

+12V

GND

G

N

D

P

B1

NO1

COM

1 2

Black

Red

Pink

Violet

B

R

S485

12 VDC

+

-

1. Put Dipswitch No.1 to position ON. RTT beeps continuously and the red led blinks.

2. Put Dipswitch No.1 to position OFF.

3. Wait for Beep + OK Beep (short + short + long beep)

After the OK beep, the coupling is done.

1 2

ON

If secure installation is needed, the reader can be connected to remote relay unit at secured area, which also can play the role of request-to-exit push button. Follow the instructions bellow to pair(couple) both devices or refer to the Remote Relay’s Manual.

12 VDC

+

-

1N4007

+

-

RTT

Black

Red

Pink

Violet

Black

Brown

Pink

Violet

Red

White

Yellow

COM

NO

GND

12V out

A (RS485)

B (RS485)

7

Warning: Changing the ADMIN ﬁnger will also unpair the remote relay unit.

PAIRING - BIOMETRIC READER AND REMOTE RELAY UNIT

Pairing B100PROX-SA v2 with DINRTT

Pairing B100PROX-SA v2 with RTT

Pairing B100PROX-SA v2 with RU2

1. Put the Jumper to closed position. RU2 beeps continuously and the red led blinks.

2. Put the Jumper to open position.

3. Wait for Beep + OK Beep (short + short + long beep)

After the OK beep, the coupling is done.

12 VDC

+

-

1N4007

+

-

RU2

Violet

Pink

COMNO

A (RS485)

B (RS485)

+12V

GND

+12V

B100PROX-SA

1

2

max. 50 meters

8

short beep

Swipe Admin Finger 1 time

Action

Wait 5 seconds (until fast blinking)

Swipe User Finger min. 6 times

(until short + long beep)

Finger

Backlight

Buzzer Sound

x 1

Use point ﬁngers as Administrator and Installer. You can use the other ﬁngers as access ﬁngers. Administrator ﬁnger is enrolled at the end of the system installation. Initial enrollment of the Admin ﬁnger is described in installer manual.

ADMINISTRATOR PROGRAMMING

ADD Finger Relay 1 (Finger that will activate on board relay 1)

slow blinking

fast blinking

short + long beep

short beep

INSTALLER

RIGHT

ADMIN

LEFT

x 6

Present card/tag 1 time

fast blinking

short + long beep

x 1

or

Swipe Admin Finger 2 times

Action

Wait 5 seconds (until fast blinking)

Finger

Backlight

Buzzer Sound

x 2

ADD Finger Relay 2 (Finger that will activate remote relay 2)

slow blinking

fast blinking

short beep

short + long beep

short beep

Swipe User Finger min. 6 times

(until short + long beep)

x 6

Relay 2 is available if the reader is used with remote relay unit with 2 relays(DINRTT and RU2). Consult the installer if Relay 2 is available in your system.

Present card/tag 1 time

fast blinking

short + long beep

x 1

or

Swipe Admin Finger 3 times

Action

Wait 5 seconds (until fast blinking)

Finger

Backlight

Buzzer Sound

x 3

Relay 2 is available if the reader is used with remote relay unit with 2 relays(DINRTT and RU2). Consult the installer if Relay 2 is available in your system.

ADD Finger Relay 1&2 (Finger that will activate relay 1&2)

slow blinking

fast blinking

short beep

short + long beep

short beep

Swipe User Finger min. 6 times

(until short + long beep)

x 6

Present card/tag 1 time

fast blinking

short + long beep

x 1

or

Swipe Admin Finger 4 times

Action

Wait 5 seconds (until fast blinking)

Swipe User Finger

Finger

Backlight

Buzzer Sound

x 4

DELETE Finger

slow blinking

fast blinking

short beep

short + long beep

short beep

x 1

Present card/tag 1 time

short + long beep

x 1

or

fast blinking

Swipe Admin Finger 5 times

Action

Wait 5 seconds (until fast blinking)

Swipe NEW Admin Finger min.6 times

Finger

Backlight

Buzzer Sound

x 5

x 6

short beep

short + long beep

3 short beeps

Swipe Admin Finger 6 times

Action

Wait 5 seconds (until fast blinking)

Swipe NEW Installer Finger min.6 times

Finger

Backlight

Buzzer Sound

x 6

CHANGE ADMIN Finger

CHANGE INSTALLER Finger

slow blinking

fast blinking

short beep

short + long beep

short beep

slow blinking

fast blinking

short beep

multiple beeps

Swipe Admin Finger 4 times

Action

Wait 5 seconds (until fast blinking)

Swipe Admin Finger 2 times

Finger

Backlight

Buzzer Sound

x 4

x 2

DELETE ALL Fingers and Cards

slow blinking

fast blinking

short beep

9

ADD Finger

Relay 1

(on board)

1 swipe

ADD Finger

Relay 2

(remote)

ADD Finger

Relay 1&2

DELETE FINGER

Change

ADMIN

Finger

Enroll

INSTALLER

Finger

2 swipes 3 swipes

4 swipes

5 swipes

6 swipes

Wait

5 seconds

(until fast blinking)

SWIPE

new finger

min. 6 times

or

present

card/tag

SWIPE

already enrolled

finger 1 time

or present card/tag

SWIPE

new finger

min. 6 times

or

present

card/tag

SWIPE

new finger

min. 6 times

or

present

card/tag

SWIPE

ADMIN finger

2 times

to

DELETE ALL

SWIPE

new ADMIN

FINGER

min. 6 times

SWIPE

new

INSTALLER

FINGER

min. 6 times

Swipe the ADMIN Finger 1 to 6 times depending of the desired menu

END END

END

END END

Administrator Programming block diagram

Only in combination

with DIN RTT and R U2

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

10

short beep

Swipe Installer Finger 1 time

Action

Swipe the INSTALLER Finger

and start counting seconds

Finger

Backlight

Buzzer Sound

Set Relay 1 Time (on board)

slow blinking

fast blinking

beeps on 1 second

short beep

INSTALLER PROGRAMMING

x 1

Swipe the INSTALLER Finger

to stop or wait 30 seconds to

put the relay in toggle mode

fast blinking

short + long beep

x 1

short beep

Swipe Installer Finger 2 times

Action

Swipe the INSTALLER Finger

and start counting seconds

Finger

Backlight

Buzzer Sound

Set Relay 2 Time (remote)

slow blinking

fast blinking

beeps on 1 second

short beep

x 2

Swipe the INSTALLER Finger

to stop or wait 30 seconds to

put the relay in toggle mode

fast blinking

short + long beep

x 1

Swipe Installer Finger 3 times

Action

Swipe Installer Finger

Finger

Backlight

Buzzer Sound

x 3

Swipe Installer Finger 4 times

Action

Swipe Installer Finger

Finger

Backlight

Buzzer Sound

x 4

BUZZER ON/OFF

slow blinking

fast blinking

short beep

short + long beep

short beep

slow blinking

fast blinking

short beep

short + long beep

short beep

BACKLIGHT ON/OFF

x 1

Wait 5 seconds (until fast blinking)

Relay 2 is available if the reader is used with remote relay unit with 2 relays(DINRTT and RU2). Consult the installer if Relay 2 is available in your system.

11

12

Set

RELAY 1

Time

(on board)

1 swipe

Set

RELAY 2

Time

(remote)

BUZZER

ON/OFF

BACKLIGHT

ON/OFF

2 swipes 3 swipes

4 swipes

Wait

5 seconds

(until fast blinking)

Swipe the Installer Finger 1 to 4 times depending of the desired menu

END END

END

Installer Programming block diagram

Swipe the Installer Finger

and start counting seconds

Swipe the Installer Finger

to put the Buzzer ON/OFF

Swipe the Installer Finger

to stop or wait 30 seconds

to put the relay in toggle

ON/OFF mode

Only in combination

with DIN RTT and R U2

Swipe the Installer Finger

and start counting seconds

Swipe the Installer Finger

to stop or wait 30 seconds

to put the relay in toggle

ON/OFF mode

Swipe the Installer Finger

to put the Backlight

ON/OFF

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

This product herewith complies with requirements of EMC directive 2014/30/EU. In addition it complies with RoHS directive EN50581:2012

XPR Access B100PROX-EH-SA v2, B100PROX-MF-SA v2 Installer Manual

Specifications and Main Features

Frequently Asked Questions

User Manual