XP Metal Detectors ADX100 Instruction Manual

CONTENTS - CONTENTS - CONTENTS - CONTENTS - CONTENTS

I. INTRODUCTION _________________________PAGE 1
II. DESCRIPTION __________________________PAGE 2
III. ASSEMBLY ___________________________PAGE 3
IV. ALKALINE BATTERIES, BATTERY LIFE, BATTERY LOW
ALERT _________________________________PAGE 4
V. CONTROLS____________________________PAGE 5
VI. DETECTING TECHNIQUES_________________PAGE 6
VII. TROUBLE SHOOTING PROBLEMS __________PAGE 7
VIII. CARE INSTRUCTIONS___________________PAGE 8
IX. ADVICE TO DETECTORISTS _______________PAGE 9
X. SPECIFICATIONS_______________________PAGE 10
XI. XP ACCESSORIES_____________________PAGE 11

WARRANTY CONDITIONS

CONTENTS - CONTENTS - CONTENTS - CONTENTS - CONTENTS

1

I. INTRODUCTION

CONGRATULATIONS ON PURCHASING AN XP METAL DETECTOR

You have invested in a high tech detector with extreme performance, designed and
developed in France. Therefore, you are taking part in the development of research in the
field of metal detecting undertaken by our Company, we thank you for that.

ADX100 is a clever combination of analog/digital technology and benefits from the latest
advances in the field. Our knowledge of that technology has led us to include a
microprocessor, analysing discrimination signals. This microprocessor, faster for
discrimination signal analysis, gives the ADX100 an increased power and stability, as
well as a better rejection of unwanted targets. The simplicity of the discrimination
adjustment will allow you to adjust it to the ground you wish to detect.

Our high

sensitivity "double D" search coils, provide very good ground penetration.
The ADX100 functions were simplified to the maximum in order to give to the beginners

an easy access and a great ease of use, while profiting from optimal performances.
You will appreciate the sturdiness and the manufacturing quality of our equipment.

Because a metal detector is generally used in extreme conditions, we have given full
attention to the most sensitive parts. ADX100 is been developed and manufactured with
quality components and material, thus ensuring your XP detector a maximum useful life.

 Impact resistant polypropylene armrest.
 Strong Cable, designed to resist movement failures.
 Robust, waterproof search coil.
 3 piece stem
 Fibreglass lower stem

Before using your detector for the first time, we recommend that
you read this instruction manual carefully in order to make full use
of its abilities.

2

II. DESCRIPTION

1 - Robust, waterproof search coil. Diameter 22.5 cm, provided with coil cover
2 – High impact plastic end
3 - Fibreglass Lower stem
4 - Twist lock
5 - Comfortable foam handle
6 – Impact resistant polypropylene armrest
7 – Srong Cable designed to resist movement failures.
8 - ABS electronics box. The box is worn under the armrest thanks to mounts

specially designed for that purpose.

III. ASSEMBLY

The assembly of your detector will only take you a few seconds.
Put the shaft together as shown on the diagram.

1. Press the 2 shafts (3) and (5) one towards the other to help the spring clips (4) locate
themselves.

2. The twist lock (6) is used to stop any movement of the fibre glass stem in the aluminium
shaft (5). Release it before inserting the fibreglass stem and then lock it without forcing
too much as shown on the diagram 9 once it is inserted at the right length.

3. Put the 2 rubber washers on each side of the plastic end (8). To facilitate the insertion
you can wet the rubber washers. Insert the plastic end on the search head and screw the
nylon bolt through, finally adding the nylon nut.

4. Wind the cable around the shaft.

5. The electronic box (1) goes under the armrest. To fix it, insert the 2 wings of the armrest
in the slides of the electronic control unit, as indicated on the diagram above.

Disassembling

To remove the control box from the armrest, proceed as
indicated below.

1. Put your hands around the control box and press
slightly with your thumbs on the sides of the
armrest 1.

2. Whilst you keep pressure with your thumbs slip the

armrest down and remove the control box from the
armrest 2.

3