Xplore WS3 Instruction Manual

Care of use

 Never try to open the earpiece of the WS3.
 Not to damage the Lithium battery.
 Not put the battery in short-circuit (fire hazard)
 Not heat the battery and the WS3.
 Not to use the WS3 if the battery has suffered damage.
 Not throw the battery or the WS3 with the dustbin (send them back to your retailer or

XPLORER 40 chemin du moulin 31320 Mervilla FRANCE).

 Not try to replace the battery yourself. This one being soldered, the temperature of soldering

or unsoldering should not exceed 350°Celsius and the time of soldering should not be longer
than 3 seconds.

✓ If you note a swelling of the casing of the batteries of the WS3 or if you see some liquid,

isolate them in a tight plastic bag, and turn over them to XP or your retailer.

If in doubt send the WS3 back to: XPLORER 40 chemin du Moulin 31320 Mervilla FRANCE

Warranty

XPLORER ensures a 24 month limited warranty from the date of the purchase of the WS3. If
warranty service should be necessary, the detector must be returned to the retailer, com plete
with proof of purchase and a notice explaining the fault. This warranty, parts and labour, does
not cover : damage due to a fall, shock or accident, deterioration due to an anormal use,
degradation due to the non-observance of the conditions of use prescribed in the instructions.
Any alteration of the electronic circuit by an unauthorized person will lead to breach of
warranty.
Xplorer reserves the right to change design or specifications of the WS3 without notice.

Declaration of conformity for E.C.

This declaration is made under the responsibility of the manufacturer:
XPLORER SARL - 8 rue du Développement – F-31320 CASTANET-TOLOSAN
We, XPLORER, hereby certify that this detector complies with the essential
requirements of European Directives RED 2014/53/EU which aims to harmonise
legislation in member states on the use of the radio spectrum, electromagnetic
compatibility and electrical safety.

Declaration date : 09.10.2018

Disposal of Waste Electrical and Electronic Equipment in the
European Union and Other Countries/Regions with Separate
Collection Systems

This symbol on the product or its packaging means that this product must not be
disposed of with your household waste. Instead, it is your responsibility to hand
this over to an applicable collection point for the recycling of electrical and
electronic equipment. This separate collection and recycling will help to conserve natural
resources and prevent potential negative consequences for human health and the
environment, which inappropriate disposal could cause due to the possible presence of
hazardous substances in electrical and electronic equipment. For more information about
where to drop off your electrical and electronic waste, please contact the shop where you
purchased this product.

INSTRUCTION MANUAL

WS3 is an optional wireless headphone designed specifically for XP detectors:

ADX150 – ADVENTIS 2 – GMAXX II – GOLD MAXX PROWER

As its name would suggest, the WS3 has two selectable input/output channels, thereby
avoiding the risk of interference (noise) between two users.
It features:

✓ a integral headphone with a radio receiver earpiece integrating 2 different

channels selectable.

✓ a batteries charger

This innovative headphone features two microprocessors, one for transmission and one for
reception, enabling a wireless digital connection. Sound quality matches wired headphones
with no hiss or background noise.

This radical new design rests on the fact that all parts are fully integrated. There is no need
for an external control box.

 The receiver is fully integrated into the headphones,

 The transmitter is directly integrated into our detectors' circuit boards and can also be

installed on any old models which were not supplied with wireless WS3 headphones.

SPECIFICATIONS

• Integral type wireless headphone

• 2 selectable channels

• Digital sound transmission by microprocessor

• Headphone built in edge extra flat rechargeable Lithium battery (7g)

• 45 hours battery life

• Fast Lithium charger: full charge in 2 hours.

• Charge monitoring system and full charge LED

• Adjustable/Memorizable volume

• Miniaturised electronics

• Transmitter with very low power consumption

OPERATION

Battery

The WS3was designed with a cutting edge extra flat rechargeable Lithium battery with a 45
hours battery life. Full charge is achieved in only 2 hours.

This Lithium battery has no memory effect and can therefore be charged at any time, even if it
is already partially charged.
Charge the WS3 headphone by connecting the charger to the DC = plug.
An LED is lit whilst charging. Once full recharged, this light will go out.
Users do not have to fully recharge the unit every time. A 20 minutes recharge will provide
around 6 hours use.

 If the battery is completely discharged, it may take up to 10 minutes for the LED to light

up. In this case, the charge system switches to slow charge for the first few minutes to

protect the battery.

 If the battery is already fully charged, the green LED will remain off.

! In the event of nonprolonged use of the WS3, it is highly recommended to leave

your battery charged and to occasionally top up in order to avoid a full

discharge.

! Failing to use the correct WS3's charger is likely to damage the WS3

headphone.

On/Off

Quickly and simultaneously press the ± buttons to switch on the WS3. You will hear a beep and the
LED will start flashing.
The same procedure is used to switch off the WS3.

NB: If you do not want the LED to flash during use, hold down the ± buttons for fifteen
seconds. The LED will not light up, but the headphones will be fully functional.

NB 2: The WS3 headphones are fitted with an AUTO-OFF system, enabling the headphones to
switch themselves off after five hours of use. This conserves battery life in the event that any
user forgets to manually switch off the device. To carry on using them, just switch them back
on.

OPERATION

Volume

Set volume with the two ± tactile keys.
The volume setting is memorized for the next time you use the headphone (unless the battery
is completely discharged).

The small black plastic plug with 'XP' logo on the end should be inserted into the headphone
socket to disable the speaker this also stops dust/water ingress.

Choice of channel

You can change the channel at any time by simultaneously pressing the ± buttons for three
seconds. Two beeps will sound and the channel will then be changed.
You can easily find out which input channel is being used:

• the LED gives off one flash per second on channel 1

• the LED gives off two flashes per second on channel 2.

Your detector is an ADX250, ADVENTIS 2, GMAXX II or a GOLDMAXX Power :

Modify your detector by using the potentiometer FREQ. SHIFT as follows: CH1 – up position; or
CH2 – down position.
For more details please refer to your detector’s instruction manual.

Your detector is an ADX100, ADX200, ADVENTIS, GMAXX or a GOLDMAXX :

Choose the receiver channel of your WS3 wireless headphones based on the transmitter
installed on the circuit board of your detector: CH1 or CH2.

Your detector is an ADX150 :

The channel of your WS3 wireless headphones is CH1.