XPiQ inc RTC20048M42, RTC200PM42 Datasheet

•

•

Input

Input Voltage • 36-72 VDC, DC input versions

90-264 VAC, AC input versions
Input Frequency • 47-63 Hz
Inrush Current • 30 A at 120 VAC, 60 A at 230 VAC

40 A at 48 VDC for DC version
Power Factor • 0.99
Leakage Current • <3 mA

Output

Output Adjustment • ±0.25 V on each rail
Line Regulation • See Table
Load Regulation • See Table
Ripple & Noise • See Table
Overvoltage • 125-135% Vnom recycle input

Protection to reset
Overload • Recycle input to reset

Protection
Overtemperature • Automatic shutdown at 100 °C

Protection measured internally with auto restart
Remote Sense • V1, V2 compensates for 0.3 V drop
Power Fail • TTL compatible signal, open collector

active low signal. Indicates any output

below 90% and/or low input below

60 VAC for AC version or 36 VDC for

DC version
Front Panel LED • Power good (green)

Power fail (amber)
Remote Enable • TTL LOW to turn output ON
Remote Inhibit • TTL HIGH (or open circuit) to turn

output ON

General

Efficiency • 70% minimum 110 VAC,

70% typical at 48 VDC full load
Switching Frequency • 125-145 kHz
Current Share • Accuracy of current share with up to 6

parallel units is 10%, available on

V1 & V2
Isolation • Input to ground 1500 VAC

Input to output 3000 VAC
Weight • 0.9 kg (2 lbs)

Environmental

Operating • 0 °C to +50 °C ambient. Full power to
Temperature +50 °C then derate by 2.5%/°C

to +70 °C
Cooling • 400 LFM/30 CFM full power operation
Storage • -40 °C to +85 °C

Temperature
Overtemperature • TTL compatible signal provides

Warning warning when power supply

temperature exceeds rating
Relative Humidity • 5-95% non-condensing
Shock & Vibration • MIL-STD-810D

EMC & Safety

Safety Approvals • EN60950 (TÜV), UL1950,

CSA950/234 per cUL, CE LVD
EMC • EN55022 level A radiated & conducted
Immunity • EN61000-4-2 level 4,

EN61000-4-3, 4, 5 level 3,

EN61000-4-6 level 2

200 Watts

RTC200 Series

Compact PCI®

Specification

•

PH: 508 429.9883

FAX: [phone]

Email: [e-mail]

Holliston, MA 01746 USA

www.XPiQ.com

Intelligent Design Quality Product

XPiQ inc.

Industry Standard

•

AC or DC Input Versions

•

Power Factor Corrected

•

Hot Swap N + 1 Redundancy

•

Active Current Share

•

International Safety Approvals

•

PICMG 2.11 Compatible

RTC200.qxd 14/5/03 3:47 pm Page 1

PH: 508 429.9883

FAX: [phone]

Email: [e-mail]

Holliston, MA 01746 USA

www.XPiQ.com

Input Output Output Output Regulation Ripple & Noise Model

Voltage Voltage Current

(1)

Line Load Pk-Pk

(2)

Number

V1 +5.0 V 25.0 A ±2% ±2% 1%

90-264 VAC

V2 +3.3 V 35.0 A ±2% ±2% 1%

RTC200PM42

V3 +12.0 V 8.0 A ±2% ±2% 1%
V4 -12.0 V 1.5 A ±2% ±3% 1%
V1 +5.0 V 25.0 A ±2% ±2% 1%

36-72 VDC

V2 +3.3 V 35.0 A ±2% ±2% 1%

RTC20048M42

V3 +12.0 V 8.0 A ±2% ±2% 1%
V4 -12.0 V 1.5 A ±2% ±3% 1%

OUTPUT VOLTAGE & CURRENT RATINGS RTC200

PIN CHART RTC200

1. V1 and V2 combined output power must not exceed 175 W .

2. Output ripple and noise is measured using 10 µf tantalum and 0.1 µf capacitors across probe and 20 MHz bandwidth.

Notes

Pin Pin Length Signal Name Description Pin Pin Length Signal Name Description
1-4 Medium V1 V1 Output 32 Medium V2 Margin V2 Marginate

5-12 Medium RTN V1 & V2 Return 33 Medium V2 SENSE V2 Remote Sense

13-18 Medium V2 V2 Output 34 Medium S RTN Sense Return

19 Medium RTN V3 Return 35 Medium V1 SHARE V1 Current Share
20 Medium V3 V3 Output 36 Medium Reserved Reserved
21 Medium V4 V4 Output 37 Medium Reserved Reserved
22 Medium RTN Signal Return 38 Medium TEMP WNG Thermal Warning
23 Medium Reserved Reserved 39 Medium INH# Inhibit
24 Medium RTN V4 Return 40 Medium Reserved Reserved
25 Medium Reserves Reserved 41 Medium V2 SHARE V2 Current Share
26 Medium Reserved Reserved 42 Medium FAL# Fail Signal
27 Short EN# Enable 43 Medium Reserved Reserved
28 Medium Reserved Reserved 44 Medium Reserved Reserved
29 Medium V1 Margin V1 Marginate 45 Long CGND Chassis Ground
30 Medium V1 SENSE V1 Remote Sense 46 Medium ACN or +DC IN +DC Input/AC IN - Neutral
31 Medium Reserved Reserved 47 Medium ACL or -DC IN -DC Input/AC IN - Line

Note: Long length pins = First mate last break, Short length pins = last mate first break.

Overall 30 mm x 170 mm x 8 HP

Mechanical Details

•

Rev 1.0

RTC200.qxd 14/5/03 3:47 pm Page 2