XPiQ inc PD110-13LA, PD110-13LC, PD110-13MA, PD110-13MC, PD110-14HA Datasheet

110 Watts

PD110 Series

Low Cost

•

100% Burn-In

•

Small Size, Light Weight

•

Three Wide Input Ranges

•

Overvoltage Protection

•

Overcurrent Protection

•

•

•

Specification

All specifications typical at nominal line, full load and 25°C

Intelligent Design Quality Product

XPiQ inc.

DC/DC Converters

Input

Input Voltage • 10 to 20 VDC

(PD110 “L” series)
18 to 36 VDC

(PD110 “M” series)
36 to 72 VDC

(PD110 “H” series)

Input Current • 15A (rms) for 12 VDC

9.4A (rms) for 24 VDC

4.7A (rms) for 48 VDC

Output

Output Voltage/ • See rating chart
Current

Ripple • 1% peak to peak maximum
Overvoltage • Provided on output #1 only,

Protection set at 112-132% of its nominal

output voltage

Overcurrent • All outputs protected in short
Protection: circuit conditions

Temperature • All outputs ±0.04%/°C maximum
Coefficient:

General

Efficiency • 60% minimum
Hold-up time • 10 msec
Line Regulation • ±0.5% max.
Isolation Voltage • 1000 VDC from input to output

Environmental

Operating • 0°C to +70°C*
Temperature

Storage • -40°C to +85°C
Temperature

MTBF • 100,000 hours
Weight • 670 g without cover

* Derate linearly from 100% load to 50°C to 50% load at 70°C

PH: 508 429.9883

FAX: [phone]

Email: [e-mail]

Holliston, MA 01746 USA

www.XP-iQ.com

53

Model 1, 2, 3 4, 5 6, 7 8, 9 10 11 12 13

PD110-10, PD110-12 OUTPUT RETURN RETURN OUTPUT N.C. N.C. KEY N.C.
PD110-13, PD110-14 #1 #1
PD110-16
PD110-23 OUTPUT COMMON COMMON OUTPUT N.C. N.C. KEY N.C.

#1 RETURN RETURN #2

PD110-31, PD110-32 OUTPUT COMMON COMMON OUTPUT N.C. OUTPUT KEY N.C.

#1 RETURN RETURN #2 #3
PD110-40, PD110-41 OUTPUT COMMON COMMON OUTPUT N.C. OUTPUT KEY OUTPUT
PD110-42, PD110-45-1 #1 RETURN RETURN #2 #3 #4
PD110-45-2, PD110-46

Notes

•

Mechanical Details

Pin Chart

1. For output #2, minimum load is 0 A and peak current is shown for 10% maximum duty cycle for less than 60 seconds.

2. PD110 “M” & “H” series is suitable for 110 watts maximum at 20 CFM forced air cooling or 80 watts maximum at convection cooling.

3. PD110 “L” series is suitable for 90 watts maximum at 20 CFM forced air cooling or 70 watts maximum at convection cooling.

4. Suffix codes for mechanical format and input range are as follows: PD110-XXYZ: “XX” is the model code from the above table. “Y” is
the input range.

(L=10-20VDC, M=18-36VDC, H=36-72VDC); “Z” is the mechanical format (A=open PCB, C=enclosed) EX: PD110-31MC, 18-36VDC input,

enclosed form.

OPEN PCB “A” ENCLOSED “C”

Output #1 Output #2

(1)

Output #3 Output #4 Maximum

Output

Model Vnom Imin Imax Tol. Vnom Imax Ipeak Tol. Vnom Imin Imax Tol. Vnom Imin Imax Tol. Power
PD110-10 5 V 0.0 A 22.0 A 3% 110 W
PD110-12 12 V 0.0 A 9.0 A 2% 110 W
PD110-13 15 V 0.0 A 7.5 A 2% 110 W
PD110-14 24 V 0.0 A 4.5 A 2% 110 W
PD110-16 30 V 0.0 A 3.6 A 2% 110 W
PD110-23 +5 V 0.8 A 10.0 A 3% +12 V 5 A 9.0 A 3% 110 W
PD110-31 +5 V 0.8 A 10.0 A 3% +12 V 5 A 9.0 A 3% -12 V 0 A 1 A 4% 110 W
PD110-32 +5 V 0.8 A 10.0 A 3% +15 V 4 A 7.5 A 3% -15 V 0 A 1 A 4% 110 W
PD110-40 +5 V 0.8 A 10.0 A 3% +12 V 5 A 9.0 A 3% -12 V 0 A 1 A 4% -5 V 0 A 1 A 4% 110 W
PD110-41 +5 V 0.8 A 10.0 A 3% +15 V 4 A 7.5 A 3% -15 V 0 A 1 A 4% +24 V 0 A 1 A 4% 110 W
PD110-42 +5 V 0.8 A 10.0 A 3% +12 V 5 A 9.0 A 3% -12 V 0 A 1 A 4% +12 V 0 A 1 A 4% 110 W
PD110-45-1 +5 V 0.8 A 10.0 A 3% +12 V 5 A 9.0 A 3% -12 V 0 A 1 A 4% +24 V 0 A 3 A 8% 110 W
PD110-45-2 +5 V 0.8 A 10.0 A 3% +24 V 3 A 5.0 A 5% -12 V 0 A 1 A 4% +12 V 0 A 1 A 4% 110 W
PD110-46 +5 V 0.8 A 10.0 A 3% +15 V 4 A 7.5 A 3% -15 V 0 A 1 A 4% -5 V 0 A 1 A 4% 110 W

OUTPUT VOLTAGE & CURRENT RATINGS PD110

Dimensions shown in inches (mm). Tolerance 0.02 (0.5) maximum. Input connector mates with Molex
housing 09-50-3051 and Molex 2878 series crimp terminal. Output connector mates with Molex housing
09-50-3131 and Molex 2878 series crimp material.

PH: 508 429.9883

FAX: [phone]

Email: [e-mail]

Holliston, MA 01746 USA

www.XP-iQ.com

54