Xorcom CXR2000, CXR3000 Getting Started Manual
Misgav Industrial Park, POB 60, D.N. Misgav 20174, Israel
9990287
Eth0
Eth1
IPMI
Tel: +972-4-9951999; Fax: +972-4-
CXR2000/CXR3000 CompletePBX: Getting Started Guide
Package Contents
CXR2000/CXR3000 (2U 19'' width unit)
Power cord
Prerequisites
You need a computer equipped with an Internet browser. Firefox is recommended. By default, the
CXR2000/CXR3000 will get its IP address from your DHCP server. To check the IP address or to
set the CXR2000/CXR3000 static IP address you will need to connect a keyboard and a display to
the CXR2000/CXR3000.
Step 1: Powering Up the Unit
1. For safety reasons, if the line wiring exits the building, it is essential to ground the unit.
Note: Not properly grounding this device will void your warranty!
a. Connect a grounding tab to the grounding screw on the rear panel.
b. Using 12-16 gauge wire, connect the grounding tab to a reliable ground.
Support hardware for 19'' cabinet
CompletePBX software preinstalled on
the hardware
Grounding
screw
Power Supply
Figure 1: Grounding Screw on CXR2000 Rear Panel
Grounding
screw
Power Supply
Figure 2: Grounding Screw on CXR3000 Rear Panel
2. Connect a keyboard and a VGA/SVGA screen.
3. Connect the unit to the LAN.
4. Connect the power cord to the device and turn on the power using the switch on the rear panel.
The device startup process takes about 2 minutes. The startup time depends on the number of
telephony ports installed in your CXR2000/CXR3000 unit.
Step 2: Submit Warranty Activation Request
At this point activate the product warranty (a pre-requisite for submitting any request for technical
support). Go to https://xorcom.com/xorcom-product-warranty, complete and submit the form found
there.
PM0616.05 - CXR2000/CXR3000 CompletePBX Getting Started Guide (electronic version) Page 1 of 5
Misgav Industrial Park, POB 60, D.N. Misgav 20174, Israel
9990287
Tel: +972-4-9951999; Fax: +972-4-
Step 3: Configure or Get the IP Settings for CXR2000/CXR3000
If you have a DHCP server: The CXR2000/CXR3000 will get the IP address from the DHCP server.
To get the IP address:
1. Login to the CXR2000/CXR3000:
a. User name: root
b. Password: !x0rc0m!voip5472#
Note: Note the use of the number zero in the password
c. The default CompletePBX keyboard configuration is US English. When entering the
password, the # (hash) key is shift/3 (i.e. uppercase three).
On UK keyboards, the hash character is located below the backspace, above the
right-hand enter key.
2. To get the IP address use the command
ip addr show dev eth0
:
As a result you’ll
get a block of data like this:
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
link/ether 00:22:4d:ab:18:8c brd ff:ff:ff:ff:ff:ff
inet 192.168.0.64/20 brd 192.168.15.255 scope global dynamic eth0
valid_lft 125725sec preferred_lft 125725sec
inet6 fe80::222:4dff:feab:188c/64 scope link
valid_lft forever preferred_lft forever
In this example the CXR2000/CXR3000 IP address is 192.168.0.64.
Method 1: Set up a static IP address via command line.
1. Login into your system as root, as described above
2. Replace 1.2.3.4/24 and 1.2.3.1 with the required IP address (in CIDR format) and default
gateway and then run the following command:
nmcli con mod eth0 ipv4.method manual \
ipv4.address 1.2.3.4/24 ipv4.gateway 1.2.3.1
3. Define the DNS server in the /etc/resolv.conf file. For example:
nameserver 5.6.7.8
4. Run systemctl restart network in order to apply the changes
Method 2: Set up a static IP address by using nmtui utility.
1. Login into your system as root, as it described above
2. Run the nmtui command and define a static IP address and the default gateway
3. Define the DNS server in the /etc/resolv.conf file:
PM0616.05 - CXR2000/CXR3000 CompletePBX Getting Started Guide (electronic version) Page 2 of 5
Loading...