Xoop Lighting P180 User Manual

Download

Page 1

LIGHT( 4 in 1)LED WASH

USER MANUAL

Page 2

table of CONTENTS

Dimen sio ns

Safet y Inf orm ation

Fixtu re ov erv iew

Intro duc tio n

AC powe r

Power v olt age

Power c abl es

Relay ing p owe r to othe r dev ice s

Data li nk

Tips for r eli abl e data tr ans mis sion

Physical installation

Faste nin g the f ixtur e to a fl at su rface

Setup

Contr ol pa nel a nd menu n avi gat ion

DMX add res s set ting

W-D MX cont rol

Onboa rd co ntr ol menu s

Dimme r mod e

DMX pro toc ols

Speci fic ati ons

Page 3

Dimensions

All dimensions are in millimeters

1.0

Page 4

WARNING! Read the safety precautions in this section before installing, powering, operating or servicing this product

The follo wing sy mbols are u sed to id en tify im portant s afety i nformat ion on th e pr oduct a nd in this ma nual:

DAN GER! Saf ety haz ard. Ris k of seve re inj ury or de ath.

Warning! Risk Group 3 (high risk) LED product according to EN 62471. Do not look into the beam at a distance of less than 3 meters from the front surface of the product. Do not view the light output with optical instruments or any device that may concentrate the beam.

This product is for professional use only. It is not for household use.

This product presents risks of severe injury or death due to fire and burn hazards, electric shock and falls.

Read this manual before installing, powering or servicing the fixture, follow the safety precautions listed below and

observe all warnings in this manual and printed on the fixture. If you have questions about how to operate the fixture

safely, please contact your supplier.

PROTECTION FROM ELECTRIC SHOCK

l Disconnect the fixture from AC power before removing or installing any cover or part and when not in use.

l Always ground (earth) the fixture electrically.

l Use only a source of AC power that complies with local building and electrical codes and has both overload and

l Before using the fixture, check that all power distribution equipment and cables are in perfect condition and rated for

l Power input and through out cables must be rated 20A minimum, have three conductors 1.5 mm² (16 AWG) minimum

l Use only cable connectors to connect to power input sockets. Use only

l Isolate the fixture from power immediately if the power plug or any seal, cover, cable, or other component is

DAN GER! Haz ardou s vol tage. R isk of let hal or se vere ele ctric s hock.

WAR NIN G! Fir e hazar d.

WAR NIN G! LED l ight emi ssion . Risk of eye i njury.

WAR NIN G! Bur n hazar d. Hot sur face. D o not tou ch.

WAR NIN G!

Wea r pro tec tiv e eye wear.

WAR NIN G!

Ref er to use r man ual.

ground-fault (earth-fault) protection.

the current requirements of all connected devices.

conductor size and an outer cable diameter of 5 - 15 mm . Cables must be hard usage type (SJT or equivalent) and heat-resistant to 90° C minimum.

PowerCON TRUE 1 PowerCON TRUE 1

® ®

cable connectors to connect to power through put sockets.

damaged, defective, deformed, wet or showing signs of overheating. Do not reapply power until repairs have been completed.

2.0

Page 5

l Refer any service operation not described in this manual to a qualified technician.

l Socket outlets used to supply the fixture with power or external power switches must be located near the fixtures and

easily accessible so that the fixtures can easily be disconnected from power.

PROTECTION FROM BURNS AND FIRE

l The exterior of the fixture becomes hot during use. Avoid contact by persons and materials.

Allow the fixture to cool for at least 10 minutes before handling.

l Keep all combustible materials (e.g. fabric, wood, paper) at least 100 mm away from the fixture.

l Keep flammable materials well away from the fixture.

l Ensure that there is free and unobstructed airflow around the fixture.

l Do not illuminate surfaces within 200 mm of the fixture.

l Do not attempt to bypass thermostatic switches or fuses.

l If you relay power from one fixture to another using power throughput sockets, do not connect more than ten the

fixture in total to each other in an interconnected chain.

l Connect only other the fixture to fixture power throughput sockets. Do not connect any other type of device to these

sockets.

l Do not connect any other type of device to these sockets.

l Do not stick filters, masks or other materials onto any optical component, besides the optional CLF Yara filters.

l Do not modify the fixture in any way not described in this manual.

l Do not use fixture on a dimmer.

PROTECTION FROM INJURY

l Do not look continuously at LEDs from a distance of less than 3 meters from the front surface of the fixture without

protective eyewear such as shade 4-5 welding goggles. At less than this distance, the LED emission can cause eye injury or irritation. At distances of 3 meters and above, light output is harmless to the naked eye provided that the eye’s natural aversion response is not overcome.

l Do not look at LEDs with magnifiers, telescopes, binoculars or similar optical instruments that may concentrate the

light output.

l Ensure that persons are not looking at the LEDs from within 3 meters when the product lights up suddenly. This can

happen when power is applied, when the product receives a DMX signal, or when SERVICE menu items are selected.

l Fasten the fixture securely to a fixed surface or structure when in use.

l Ensure that any supporting structure and/or hardware used can hold at least 10 times the weight of all the devices

they support.

l Allow enough clearance around the fixture to ensure that it cannot collide with an object or another fixture when it

moves.

l Check that all external covers and rigging hardware are fastened securely.

l Block access below the work area and work from a stable platform whenever installing, servicing or moving the

fixture.

l Do not operate the fixture with missing or damaged covers, shields or any optical component.

3.0

Page 6

fixture overview

LCD Display

Control buttons

AC mains power

throughput

5P DMX output

3P DMX output (optional)

5P DMX input

3P DMX input (optional)

Antenna wireless solutions(optional)

Safety cable

attachment point

AC mains power

input

4.0

Page 7

Introduction

Outdoor RGBW LED Fixture

¢ RGBW color control with color temperature control ¢ Onboard control panel and backlit OLED graphic display

¢ Electronic shutter with strobe and pulse effects

¢ Smooth RGBW color mixing ¢ XLR Connector upgrade software ¢ IP65 rating ¢ Silent operation ¢ Smooth projection ¢ Powercon true 1 ¢ RDM ready

in & out

Using for the first time

Warning! Read “Sa fety Info rmation” on page 2 before installing, powering, operatin g or servicing the fixture. Before applying power to the fixture:

l Check that the loca l AC mains power source is within the fixt ure’s power voltage and freq uency ranges.

l See “Power cabl es and power plug” on page 6. Install a power input connecto r on a suitable

power cable.

AC power

War ning! Read “Safet y Information” star ting on page 2 before connectin g the fixtures to AC mains power.

War ning! For protectio n from electric shock, the fixt ure must be grounded (earth ed). The power distributi oncircuit must be equip ped with a fuse or circuit breaker and grou nd-fault (earth -fault) protect ion.

War ning ! Sock et outlets or exter nal power swi tches used to suppl y the fix ture with power mus t be loc ated near the fixtu re and ea sily acces sibl e so that the fixt ures can easily be discon nect ed fro m power.

Impor tan t! Do n ot inse rt or r emo ve live conne cto rs to a pply or c ut po wer, a s this may cau se ar cin g at the te rmi nal s that wi ll da mag e the con nec tor s.

Impor tan t! Do n ot use an e xte rna l dimmi ng sy ste m to supp ly po wer t o the fix tur e, as t his may c aus e damag e to th e fix ture th at is n ot co vered b y the p rod uct war ran ty.

The fix tur e can b e hard- wir ed to a e lectr ica l ins talla tio n if yo u want to i nst all i t perma nen tly, o r a pow er plug that is s uit abl e for the l oca l pow er outl ets c an be i nstal led o n the p ower ca ble .

PowerCON TRUE 1

Power CON T RUE 1

power voltage

War nin g! Ch eck tha t the v olt age ran ge sp eci fied on t he fi xtu res ser ial n umber labe l mat ches the loc al AC main s pow er vo ltage b efo re ap plyin g pow er to t he fixt ure .

The fix tur es ac cepts AC m ain s pow er at 100 -24 0 V nom inal, 5 0/6 0 Hz. D o not app ly AC ma ins p ower to t he fixtu re at a ny ot her vol tag e tha n speci fie d.

5.0

Page 8

power cables

Wire Color (EU models)

Wire Color (US models)

Conductor

Symbol

Brown

Black

LiveLBlue

White

Neutral

Yellow/Green

Green

Ground (earth)

Power i npu t and t hroug hpu t cab les mus t be ra ted 1 6A minim um, h ave t hree co ndu cto rs 1.5 mm ² (16 AWG) minim um co ndu ctor si ze an d an ou ter cab le di ame ter of 5 - 15 m m. Ca ble s must be h ard u sag e type (S JT or equiv ale nt) a nd heat - res ist ant to 90 °C mi nim um. In th e EU th e cab le must b e HAR a ppr oved or e qui val ent.

If you in sta ll a po wer plu g on th e pow er cabl e, in sta ll a grou ndi ng- type (e art hed ) plug th at is r ate d 16A minim um. F oll ow the pl ug ma nuf actur er ’s in str uct ions. Tabl e 1 shows s tan dar d wire co lor -co ding sc hem es and som e pos sib le pin id ent ifi catio n sch eme s; if pin s are n ot cl early i den tif ied.

Table 1 : Wire color-coding and power connections

Relaying power to other devices

War nin g! Do n ot conn ect m ore t han ten f ixt ure s in tota l to AC ma ins p ower in o ne in ter conne cte d chain. Power c an be r ela yed to an oth er de vice vi a the throu ghp ut so cket.

If you da isy c hai n the fix tur es in a c hain so t hat t hey a ll draw AC m ain s pow er via th e fir st fi xture , cer tai n point s mus t be re spect ed:

• A heavy d uty, t hre e-c onduc tor, 1 6 AWG or 1.5 mm cabl e wit h SJT o r equ ivale nt ca ble j acket m ust b e use d to conne ct th e fir st fixt ure t o AC mai ns powe r.

Power CON T RUE 1

• connectors must be used to draw AC mains powe r from the fixtures power throu ghput sockets and yellow co nnectors must be used to supply pow er at the fixture’s power input sockets.

• No matt er wh at th e AC mains p owe r vol tage is , do no t con nect mo re th an te n the fix tur e in to tal ( inc lud ing the fir st fi xtu re) to AC ma ins p owe r in one in ter con necte d dai sy ch ain usi ng po wer i nput an d thr oug h out conne cto rs.

PowerCON TRUE 1

Power CON T RUE 1

DATA LINK

A DMX 512 da ta li nk is r equir ed in o rde r to cont rol a f ixt ure via D MX. T he fi xtu re has 5- pin X LR co nnect ors f or DMX dat a inp ut an d outpu t. Th e pin -ou t on all co nne cto rs is pin 1 = s hie ld, p in 2 = cold ( -), a nd pi n 3 = hot (+) Pins 4 an d 5 in th e 5-p in XLR co nne cto rs are no t use d.

tips for reliable data transmission

To connec t the f ixt ure to da ta:

1. Conne ct the DM X data ou tput from the contr olle r to the 5- pin X LR conn ect or of t he near est f ixt ure.

2. Conn ect t he DM X outpu t of th e fix ture cl ose st to t he cont rol ler t o the DMX i npu t of th e next fi xtu re an d conti nue c onn ectin g fix tur es outp ut to i npu t.

6.0

Page 9

Physical installation

War nin g! Th e fix ture mu st be e ith er fast ene d to a fl at surf ace s uch a s a stage o r wal l, or c lampe d to a tr uss o r simil ar st ruc ture in a ny or ien tatio n usi ng a ri gging c lam p.

War nin g! If t he fixt ure c an ca use inj ury o r dam age it if f all s, at tach an a ppr ove d safet y cab le to o ne of the safet y cab le at tachm ent p oin ts on the b ase ( see “ Fixtu re ov erv iew” on p age 4 ).

Check t hat a ll su rface s to be i llu minat ed ar e min imum 20 0 mm. f rom t he fixt ure , tha t combu sti ble m ateri als (wood , fab ric , paper, e tc. ) are m inimu m 100 m m. fr om the fi xtu re, t hat the re is f ree a irflo w aro und t he fixt ure and tha t the re ar e no flam mab le ma teria ls ne arb y.

Fastening the fixture to a flat surface

The fix tur e can b e faste ned t o a fix ed flat s urf ace t hat is or ien ted a t any ang le. C hec k that th e sur fac e can suppo rt at l eas t 10 time s the w eig ht of all f ixt ure s and equ ipm ent t o be inst all ed on i t.

War nin g! Th e sup porti ng su rfa ce must b e har d and f lat or ai r ven ts in t he base m ay be b loc ked, wh ich w ill cause o ver hea ting. F ast en th e fixtu re se cur ely. Do not sta nd it o n a sur face or l eav e it wh ere it ca n be mo ved or can fa ll ov er. Att ach a sec ure ly an chore d saf ety c able to t he sa fet y cable a tta chm ent poi nt (s ee “F ixtur e overv iew ” on pa ge 4) if th e fix tur e is to be in sta lle d in any lo cat ion w here it m ay fa ll an d cause i nju ry or damag e if th e pri mary at tac hme nt fail s.

1. Bloc k acc ess u nder th e wor k are a. Wo rking f rom a s tab le plat for m, ha ng the fi xtu re on t he trus s. Tig hte n the rig gin g cla mp.

2. Secu re th e fix ture ag ain st cl amp fai lur e wit h a secon dar y att achme nt su ch as a n appro ved s afe ty cabl e that is r ate d for t he weig ht of t he fi xture u sin g one o f the att ach men t point s at th e edg es of the b ase ( see “Fixt ure o ver view” o n pag e 4). D o not use a ny ot her p art of th e fix tur e as a safe ty ca ble a ttach men t poi nt.

7.0

Page 10

SETUP

War nin g! Re ad “Saf ety I nfo rmati on” o n pag e 2 befor e ins tal ling, p owe ring, oper ati ng the fixtu re.

Control panel and menu navigation

The onb oar d con trol pa nel a nd ba cklit g rap hic d ispla y are u sed t o set the f ixt ure ’s DM X addre ss, c onf igure indiv idu al fi xture s ett ing s (pers ona lit y), rea d out d ata a nd exec ute s erv ice uti lit ies . See “On boa rd co ntrol menus ” on pa ge 15 f or a comp let e lis t of menu s and c omm ands.

Using t he co ntr ol butt ons

• To ente r the men u sel ect [ MODE] .

• Press [ UP] a nd [D OWN] to s cro ll wi thin a me nu or a dju st valu es.

• To ente r a menu, s ele ct a fu nctio n or ap ply a s elect ion , pre ss [ENT ER] .

• To esca pe a func tio n or mo ve back o ne le vel i n the men u str uct ure, pr ess [ MOD E].

• Holdi ng do wn th e "UP" an d "DO WN" b utton f or mo re th an 3 seco nds , the M ENU dis pla y wil l rotat e 180 °.

DMX address setting

The DMX address, also known as the start channel, is the first channel used to receive instructions from the controller.

For ind epe nde nt cont rol , eac h fixtu re mu st be a ssign ed it s to a se parat e cha nne l .

The DMX a ddr ess c an be con fig ure d by usin g the D MX ADD RESS me nu in t he co ntrol p ane l. Fo r setti ng th e DMX add res s pre ss [ENT ER] b efo re you ca n cha nge t he addr ess .

• The m ain scr een w ill s how a 'do t' an d the b ackli ght w ill b e switc hed o ff wh en a DM X signa l is de tec ted.

• The f ixtur e is fu lly R DM read y. So when yo u are u sing a RDM rea dy co nsole y ou ca n add ress th e uni t and read ou t its c omp lete st atu s. Fo r RDM fun cti ons p lease r efe r to th e ANSI/E STA E1. 20- 200 6 stand ard

W-DMX control

Go to the W-DMX section in the main menu, press the button “UP” to switch off Wireless DMX or disconnect with all connected Transmitters.

Press t he bu tto n “DOWN' t o set t he un it in the ” rea dy to c onnec t wit h all n ot conn ect ed tr ansmi tte rs' mode. I f you p res s the mod e but ton o n the Wir ele ss so lutio n tra nsm itter a ll th e uni ts in thi s mod e wil l be conn ect ed.

If the un it is s ucc essfu lly c onn ected i n the h ome d ispla y the s ign“ V ” . Appea rs. I f the u nit is no t conne cte d to a tr ansmi tte r in th e home di spl ay th e sign “ ? ”. I f the u nit i s switc hed o ff in t he ho me displ ay th e sig n “X ”.

l Holding the MENU and ENTER button for more than 3 seconds, the wireless board will reset.

l Do not use Wireless DMX and Wired DMX at the same time because it will give unwanted interference

8.0

Page 11

Onboard control menus

NO.

Main Menu

Menu level 2

Menu level 3

Remark

DMX

001-512

Default 001

PERS

HSV

1. Hue 2. Sat ura tion 3. Valu e

Default : STAG

COL

1.Red, 2.Green, 3.Blue

COL.D

1. Dimmer, 2.Red, 3.Green, 4.Blue

Co2

1.Red , 2 .Gr een , 3 .Blue , 4 .Wh ite

Co2.D

1. Dimmer, 2.Red, 3.Green, 4.Blue, 5 .White

Co2.S

1.Str obe , 2. Di mmer, 3. Red , 4.G reen, 6 .Bl ue,

6.Whi te, 7 .CC T

STAG

1.Str obe , 2. Di mmer , 3. Fun cti on set , 4. Red ,

5.Gre en , 6. Blu e , 7.Whi te, 8 .CC T , 9.M acro co lor,

10.AU TO, 11. Speed , 1 2.I D

COLOR

Dimme r

0-255

Default : 255

Red

0-255

Default : 255

Green

0-255

Default : 255

Blue

0-255

Default : 255

White

0-255

Default : 255

Strob e

0-20

Default : 00

AUTO

AT (1 - 10)

Speed 0 20-

Default : AT01

PR (1 )-10

SET

01 - 66

Default : 01

ID.SW

ON / OFF

Default : OFF

REFRE SH

600 / 120 0 / 240 0 / 480 0 Hz

Default : 600

KEYLO CK

ON/OF F

Passw ord <mode , up, m ode , down>

D.spe ed Norma l

Default : Normal Smoot h 1/S moo th 2/Sm oot h 3/S mooth 4

D.cur ve

linea r

Default : linear

Squar e (Sq uar e law)

INV Sq (I NV Sq uar e law)

S-Cur ve

Speci al

WDMX

ON / OFF / RE SET

Default : OFF

CALIB NORMA L

Default : FACTORY FACTORY

UPLD

Passw ord

< up, up, d own , dow n>

9.0

Page 12

Onboard control menus

NO.

Main Menu

Menu level 2

Menu level 3

Remark

EDIT

Progr ame

(01 - 09)

Scene

(01 - 30)

Red 0-2 55

Progr ame 1 0 has 9 0 Scene s

Green 0 -25 5

Blue 0- 255

White 0 -25 5

Progr ame 1 0

Scene

(01 - 90) Strob e 0-2 0

Tim e 0-2 55

Fade 0- 255

INFO

VERSI ON

VX.XX

USAGE .T Xxxx H

RESET

Use tim e res et (p asswo rd)

TEMP

XXX℃

RDM.U ID

0x080 008 0xx xx

FACTORY

LOAD

10.0

Page 13

DIMMER MODE

provides five dimming options (see picture below):

Outpu t

DMX %

LINEA R

Outpu t

DMX %

S-CURVE

l LINEAR – the increase in light intensity appears to be linear as DMX value is increased.

l SQUARE LAW – light intensity control is finer at low levels and coarser at high levels.

l INV Square law – light intensity control is coarser at low levels and finer at high levels.

l S-CURVE – light intensity control is finer at low levels and high levels and coarser at medium levels.

l Special – the light intensity was linear increase with DMX value , and light intensity control is finer at low level

with DMX values decrease , the dimmer speed will also has effect on it

Whichever DIMMER CURVE option you select, you can choose between NORMAL or SMOOTH 1 / 2 / 3 / 4 dimming

settings:

l NORMAL is the default setting. It gives a virtually instantaneous reaction when you dim from one intensity to

another, but dimming slowly from one intensity to another may appear slightly uneven.

l The MOOTH 1 / 2 / 3 / 4 setting gives smoother dimming during slow changes in intensity, but it limits the speed

of dimming changes slightly. This makes it ideal for slow, smooth dimming, but a short time-lag may be

noticeable if you try to dim quickly from one intensity to another.

Outpu t

DMX %

SQUAR E LAW

Outpu t

DMX % Up DM X % Dow n

SPECI AL

Outpu t

DMX %

INVER SE SQ UAR E LAW

11.0

Page 14

dmx protocols

HSV

Function

Value

Setting

Remark

Hue

000 - 255

0 - 100%

Saturation

000 - 255

0 - 100%

Value

000 - 255

0 - 100%

3 CH

Function

Value

Setting

Remark

Red

000 - 255

0 - 100%

Green

000 - 255

0 - 100%

Blue

000 - 255

0 - 100%

4 CH

Function

Value

Setting

Remark

Dimmi ng

000 - 255

0 - 100%

Red

000 - 255

0 - 100%

Green

000 - 255

0 - 100%

Blue

000 - 255

0 - 100%

4 CH

Function

Value

Setting

Remark

Red

000 - 255

0 - 100%

Green

000 - 255

0 - 100%

Blue

000 - 255

0 - 100%

White

000 - 255

0 - 100%

5 CH

Function

Value

Setting

Remark

Dimmi ng

000 - 255

0 - 100%

Red

000 - 255

0 - 100%

Green

000 - 255

0 - 100%

Blue

000 - 255

0 - 100%

White

000 - 255

0 - 100%

3 cha nnels：H SV

Note: In H SV m ode , Hue s tan ds f or t he vis ibl e li ght, such as r ed, yellow, an d cy an, etc. Satu rat ion refer s to the dom inanc e

of hue i n t he col or; when satu rat ion is at 100% , t hen the col or is at its pure st. Value is the co lor 's brigh tne ss; when value i s at 10 0%, t hen the c olo r is at i ts brig hte st.

3 cha nnels：C oL

4 cha nnels：C oL.d

4 cha nnels：C o2

5 cha nnels：C o2.d

12.0

Page 15

dmx protocols

7CH

Function

Value

Setting

Remark

Shutt er

000 - 019 020 - 024 025 - 064 065 - 069 070 - 084 085 - 089 090 - 104 105 - 109 110 - 12 4 125 - 129 130 - 144 145 - 149 150 - 164 165 - 169 170 - 184 185 - 189 190 - 204 205 - 209 210 - 224 225 - 229 230 - 244 245 - 255

No func tio n Shutt er op en Strob e 1 (fa st → sl ow) Shutt er op en Strob e 2: op eni ng puls e (fa st → sl ow) Shutt er op en Strob e 3: cl osi ng puls e (fa st → sl ow) Shutt er op en Strob e 4: ra ndo m strob e (fa st → sl ow) Shutt er op en Strob e 5: ra ndo m openi ng pu lse ( fast → sl ow) Shutt er op en Strob e 6:r and om clos ing p uls e (fast → s low ) Shutt er op en Strob e 7: bu rst p ulse (f ast → s low ) Shutt er op en Strob e 8: ra ndo m burst p uls e (fa st → slow ) Shutt er op en Strob e 9:s ine w ave (fa st → sl ow) Shutt er op en Strob e 10: b urs t (fast → s low ) Shutt er op en

Dimmi ng

000 - 255

0 - 100%

Red

000 - 255

0 - 100%

Green

000 - 255

0 - 100%

Blue

000 - 255

0 - 100%

White

000 - 255

0 - 100%

CCT

000 - 009 010 - 255

No func tio n 10000 K - 250 0K

7 cha nnels：C o2.s

13.0

Page 16

dmx protocols

12CH

Function

Value

Setting

Remark

1 Shutt er

Dimmi ng

000 - 255

0 - 100%

Fixtu re contr ol setti ngs

000 - 044 045 - 049 050 - 054 055 - 059 060 - 064 065 - 069 070 - 074 075 - 089 090 - 094 095 - 099 100 - 104 105 - 129 130 - 134 135 - 139 140 - 144 145 - 149 150 - 154 155 - 159 160 - 164 165 - 169 170 - 174 175 - 179 180 - 249 250 - 255

No fu nction Normal dimming, speed o f cha nge s unr est ric ted 1 No fu nction

Dimmer 1

Dimmer 2

Dimmer 3

Dimmer 4 No fu nction

Calibrated color output mo de- C OLO R CAL IB = ON No function

Raw color output mode- COLOR C ALI B = OFF No fu nction 600 Hz Refresh rate 1200Hz Refresh rate 2400Hz Refresh rate 4800Hz Refresh rate No Fu nction

WDM X - ON No Fu nction

WDM X - OFF No Fu nction

WDM X - RESET No Fu nction illuminate display

Valu e mus t be he ld fo r 3 seconds to activate.

Red

000 - 255

0 - 100%

Green

000 - 255

0 - 100%

Blue

000 - 255

0 - 100%

White

000 - 255

0 - 100%

CCT

000 - 009 010 - 255

No func tio n 10000 K - 250 0K

12 ch annel s：Stag

14.0

Page 17

12CH

Function

Value

Setting

Remark

Macro c olo r

contr ol

0 - 9 10 - 179

180 - 201 202 - 207 208 - 229 230 - 255

No func tio n. RGBW co lor m ixi ng enab led

Color w hee l rot ation e ffe ct

Clock wis e, fa st → slow Stop (thi s wil l sto p where ver t he co lor is at t he ti me) Count er -c loc kwise , slo w → fas t Stop (thi s wil l sto p where ver t he co lor is at t he ti me)

auto &

custo m

progr am

000 009 - 010 019 - 020 029 - 030 039 - 040 049 - 050 059 - 060 069 - 070 079 - 080 089 - 090 099 - 100 109 -

110 119 - 120 129 - 130 139 - 140 149 - 150 159 - 160 169 - 170 179 - 180 189 - 190 199 - 200 255 -

No Func tio n Out1 AUTO1 Out2 AUTO2 Out3 AUTO3 Out4 AUTO4 Out5 AUTO5 Out6 AUTO6 Out7 AUTO7 Out8 AUTO8 Out9 AUTO9 Out10 AU TO1 0 cust1 c ust om pr ogram 1 Cust2 c ust om pr ogram 2 Cust3 c ust om pr ogram 3 Cust4 c ust om pr ogram 4 Cust5 c ust om pr ogram 5 Cust6 c ust om pr ogram 6 Cust7 c ust om pr ogram 7 Cust8 c ust om pr ogram 8 Cust9 c ust om pr ogram 9 Cust1 0 cus tom p rogra m10

Speed

000 - 255

Auto Sp eed o r Dim mer Spe ed( fas t → slow)

ID addr ess

selec tio n

000 009 - 010 019 -

0 - 100% ID 01 - ID 66

12 ch annel s：Stag

15.0

Page 18

ID AD DRESS S ELECT ION

VALU E

Function

VALU E

Function

VALU E

Function

VALU E

Function

000~0 09

All IDs

170~1 79

ID 17

223

ID 34

240

ID 51

010~0 19

ID 1

180~1 89

ID 18

224

ID 35

241

ID 52

020~0 29

ID 2

190~1 99

ID 19

225

ID 36

242

ID 53

030~0 39

ID 3

200~2 09

ID 20

226

ID 37

243

ID 54

040~0 49

ID 4

210

ID 21

227

ID 38

244

ID 55

050~0 59

ID 5

211

ID 22

228

ID 39

245

ID 56

060~0 69

ID 6

212

ID 23

229

ID 40

246

ID 57

070~0 79

ID 7

213

ID 24

230

ID 41

247

ID 58

080~0 89

ID 8

214

ID 25

231

ID 42

248

ID 59

090~0 99

ID 9

215

ID 26

232

ID 43

249

ID 60

100~1 09

ID 10

216

ID 27

233

ID 44

250

ID 61

110~ 119

ID 11

217

ID 28

234

ID 45

251

ID 62

120~1 29

ID 12

218

ID 29

235

ID 46

252

ID 63

130~1 39

ID 13

219

ID 30

236

ID 47

253

ID 64

140~1 49

ID 14

220

ID 31

237

ID 48

254

ID 65

150~1 59

ID 15

221

ID 32

238

ID 49

255

ID 66

160~1 69

ID 16

222

ID 33

239

ID 50

ID Ad dress I nstructions

1.Set tin g ID ad dress

1、Acces s con tro l panel f unc tio n by pres sin g MOD E until 【I D】 is di spl ayed. 2、Press E NTE R, in creas e or re duc e ID valu es by p res sing UP /DO WN be tween 0 1 and 6 6.

3、Press M ODE t o exi t.

2. Enab le or d isa ble ID 【SE T】-【IDS W】-【ON- OFF】

For ev ery DM X51 2 address the us er c an set 66 sep ara te ID a ddr esses . ID addre ssi ng is a secon dar y func tio n in DM X51 2 mode. In DMX 512 Cont rol ler Mode , the u ser ca n s imultane ous ly con trol t he ind ividu al DMX addre ss of all light s, and can contr ol th e lig hts whi ch ha ve se parat e ID ad dre ss in ind epe nde nt DMX5 12.

Selec t STAG chan nel on fi xtu re' s c ont rol pa nel (Ple ase re fer to DM X51 2 C han nel s S elect ion ). The figur e abov e s how s a simpl e D MX lay out wh ich has use d thre e u nit s a t e ach DM X a ddr ess . T he thr ee uni ts hav e d iff ere nt ID add res ses. In the DMX a ddres s: 00 1, th e use r can cont rol t he firs t thr ee li ght s sim ult aneou sly. When usi ng ch ann el 12 s elect the ch ann el numbe r is 020-02 9 and ID Addre ss= 02, the contr oll er can contro l the secon d lig ht ind ivi dua lly. Whe n using cha nne l 12 selec t the c han nel num ber i s 000 -010 an d ID Add res s=00, a ll th e lig hts are i n com mon u se at the s ame D MX ad dress .

16.0

Page 19

Specifications

Physical

Length

260mm

Width

210mm

Height

320mm

Weight

5.8 kg without accessories

Dynamic Efects

beam angle

15°

Optics

Light source

14 pcs high-power LEDs (RGBW)

Control and Programming

Control

DMX512-A

DMX channels

3 / 3 / 4 / 4 / 5 / 7 / 12

Setting and addressing

Control panel with backlit LCD graphic display

Protocol

RDM, USITT DMX512-A

CONSTRUCTION

Color

Black

Housing

High strength die-casting aluminum

Protection rating

IP 65 ( If rubbers covers are place correctly when connectors are not used )

Installation

Orientation

Any

Minimum distance to combustible materials

100 mm. from fixture

Minimum distance to illuminated surfaces

200 mm. from fixture

Connections

AC power input

PowerCON TRUE 1 input socket

AC power throughput

PowerCON TRUE 1 output socket

DMX data in/out

5 pin locking XLR (3 pin optional )

Electrical

AC power

100-240 V nominal, 50/60 Hz

Maximum total power consumption

140 W

Power supply unit

Auto-ranging electronic switch mode

Power consumption, all efects static, zero light output

<15 W

Power consumption

120 V, 60 Hz

140 W, PF * 0.994

240 V, 50 Hz

135 W, PF * 0.943

* PF = power factor. Measurements made at nominal voltage with all LEDs at full intensity. Allow for a deviation of +/- 10%.

Cooling

Passive

17.0

Page 20