COLOR TELEVISION
TS2050J
(TK2050)
CONTENTS
Safety instruction………………………………………………………………………1
General instruction……………………………… ……………………………………… .1
Alignment instruction……………………………………………………………………2
Alignment flow ..……………………………………………………………………..2
Alignment method…………………………………………………………………..3
Block diagram......………………………………………………………………………...10
MAIN IC………… …………………………………………… ………………………..11
Parts list………………………………………………………………..............16
Exploded view…………………….……………………………………………….34
Schematic diagram………………………………………………………………….36
Note: This service manual is only for professional service personnel’s reference. Before
servicing the unit, please read the following items carefully.
1 Safety instruction
1.1 X-RAY radiation precaution
1.1.1 Excessive voltage will cause harmful X-ray. To avoid this radiation hazard, the high voltage should
fall within the limitation. The appliance works at AC 120V, 60Hz. The high voltage of zero beam
current(brightness, contrast and color is min) should be within 27kV on condition that the main power
(B+) voltage is AC120V. And it should not exceed 28kV in any condition.
When servicing, please refer to the HIGH VOLTAGE CHECK procedure this service manual before
check the high voltage and the high voltage meter should be reliable and accurate.
* Keep the main power voltage at 120V when checking the high voltage.
1.1.2 The primary source of X-RAY RADIATION is the CRT. The CRT of this TV set have gotten the
approval of safety authentication inspection. The replacement CRT should be exactly the same type and
specification CRT which has gotten a similar safety approval, and check the high voltage according to
the HIGH VOLTAGE CHECK procedure.
1.2 safety precaution
a. Since the power supply circuit of this receiver is directly connected to the AC power line, an isolation
transformer is necessary during dynamic service to avoid possible shock hazard.
b. Always discharge the graphite layer conductor when moving the CRT.
c. Disconnect the power cord before replacing parts.
d. When replacing high-power resistor, keep the resistor 10 mm away from the circuit board.
1.3 Component safety precaution
Many electrical and mechanical parts in the chassis have special safety-related characteristics. These
characteristics are often passed unnoticed by a visual inspection. Replacement parts which have these
special safety characteristics are identified in this manual and its supplement electrical components
having such features are shaded or marked by on the schematic diagram and the parts list. Before
replacing any of these components, read the parts list in this manual carefully. The use of substitute
replacement parts which do not have the same characteristic as specified in the parts list may create
shock, fire, X-RAY RADIATION or other hazards.
2.General instruction
2.1 Copy the standard model data to let EEPROM (N702 24C08)of the chassis have those data before
placing it on the unit, do “factory adjustment” if necessary. If use a blank EEPROM directly, you should
preset IIC data and then do other common adjustment. Refer to TABLE1 to preset EEPROM.
2.2 the adjustment should be done under following circumstances without additional instruction
a) Alternating current 120V/60Hz
b) Preheat at least 30 min
2.3The unit has auto degaussing circuit, the auto degaussing process can be finished within 2s when the
main power. only when turn on the unit at least 20min after last time turn off TV does the auto
degaussing circuit work.
2.4 If the CRT with magnetism affects color purity and convergence, when the auto degaussing eraser. if
the color purity and convergence are still not very good, then corresponding adjustment should be done.
Refer to picture tube adjustment method for adjustment.
1
3 Alignment instruction
3.1 Debugging item
a)adjust mode instruction
b)B+ voltage adjustment
c)RFAGC voltage adjustment
d)focus adjustment
e)Screen-grid voltage white balance, sub brightness adjustment
f)filed scan center, line , amplitude adjustment
g)H-scan center adjustment
3.2 Alignment flow
E2PROM copy
High voltage check
B+ adjustment
RFAGC adjustment
Focus adjustment
Screen-grid voltage white
balance
Scan amplitude
center
X-ray protect check
Filament voltage check
AV check
Sub brightness check
White balance check
Color Purity, convergence check
AV, S terminal check
check
Fig-1 alignment flow
2
The unit and remote control
CCD function check
3.3 Enter/exit factory adjustment method
Use remote control, press “MENU” button, then press 6483,”TEST”will appear on screen to show that
you have entered the factory adjustment method, press “STANDBY” to exit it. Use factory remote control,
press the “PRESET” and “TEST” button, then the screen display “test” which means you have entered
into the factory adjustment mode, press the “TEST” or “STANDBY” to exit.
3.4 select adjustment item and adjust data
after entering factory adjustment mode, press 1-4 number buttons to select menu 1- menu 4; To enter
into MENU0, MENU5-MENU9, you may return to MENU1-MENU4 or just after you enter into “TEST”
interface, quickly press“CHILD LOCK” button and then the number button (0,5-9) to enter into relative
menus. Press “CH+” and “CH-” to select and “V+” and “V-”to adjust.
3.5 User purview
a).Factory adjustment mode menu1-menu4: only debugging worker, service checker, craftwork
technician, designer may operate.
b).Factory adjustment mode menu0, menu5-menu9: only craftwork technician, designer may operate.
4 Alignment method
4.1 B+ voltage adjustment
a) connect B+ point with a digital voltmeter to measure the negative pole of VD524
b) receive PHILIPS test pattern signal and set the picture to standard.
c) Adjust VR501 to let the value of B+ voltage be 110 V ±0.5 V (yongxin super pure flat)
4.2 AGC adjustment
a) receive VHF-H band,60 dB RF signal.
b) Select factory menu2 of “AGC”.
c) Adjust AGC-TOP to let the picture just without noisy, then the voltage of tuner AGC is the
required value for adjustment.
d) exit factory menu
4.3 Normal temperature aging
a) do not receive signals.
b) under ”Test” condition, set the accelerator to an appropriate point for aging.
4.4 Accelerator adjustment
a) do not receive signals;
b) select “SC” of factory menu3 to let the field scanning stop working.
c) adjust acceleration potentiometer to let bright lines just appears on screen.
d) exit SC menu.
4.5 High voltage check
Note: the main power voltage (B+=110 V)can affect the high voltage directly, so be sure to let the B+
power voltage accurate. Under any state, the high voltage should not exceed 28 kV.
a) connect an accurate high voltage meter between the second anode cap of picture tube and
ground.
b) turn on TV and receive testing card signal.
c) set picture to standard, the high voltage should be 25 kV± 0.5 kV.
d) the high voltage should not exceed 27KV with minimum brightness and contrast.
4.6 Focus adjustment
a) receive A12-PHILIPS (NTSC)signal
3
b) adjust focus electrode potentiometer on FBT to optimize B area focus of screen.
4.7 White balance adjustment (color temperature 12000°K± 8MPCD,X=0.270± 0.008,Y=0.283± 0.008)
a) receive full white signal, set color is 0
b) select factory menu3
c) on the basis of blue gun ”BD”, select and adjust “RD, GD” item to make white balance
respectively at brightness Y=6cd/m
2
, Y=80cd/m2 meet standard (color temperature 12000°K± 8MPCD,
x=0.270± 0.008, y=0.283± 0.008)
d)If at brightness Y=6cd/m
2,
white balance can not meet standard, you may adjust “RB, GB”item,
then repeat step C) until white balance meet standard.
4.8 Filed scanning adjustment (fig-2)
a) Receive NTSC of A12-PHILIPS test pattern signal.
b) select factory menu1
c) adjust V-SLOPE menu to let the horizontal center line of test pattern above blanking.
d) select V-SHIFT menu and adjust to let the vertical center of picture coincide with
vertical center of picture tube.
e) Select V-SIZE menu and adjust to let the vertical reproduction ratio of picture acceptable 8%.
f) Adjust V.SC to optimise the vertical S correction of picture.
Horizontal line
Under part banking
Fig-2 field scan adjustment
4.9 Horizontal scanning adjustment (Fig-3)
a) Receive A12-PHILIPS(NTSC) signal
b) Select factory menu1
c) Select H.SHIFT menu and adjust to let the scanning horizontal center coincide with mechanical
center of picture tube
d) Exit factory menu
Fig-3 line scan adjustment
a
4.10 Sub-brightness adjustment
a) Receive A12-PHILIPS(NTSC) signal
b) Select “SB” of factory menu3
c) Adjust “SB” to let things between the sixth and seventh grey scale clear
4.11 OSD adjustment
a) Receive A12-PHILIPS(NTSC) signal
b) Select OSD H and OSD V of factory menu4. Adjust OSD H and OSD V to let OSD at a specified
4
place.
c) Exit factory menu
4.12. Checking point
4.12.1 High voltage check
1) Connect High Voltage meter between CRT second anode and GND.
2) Receive A7 signal, set the control to “STANDARD”, measure the high voltage value, the reading
should be 25 kV±0. 5 kV
3) Set the brightness and contrast to miminum (zero beam current), measure the high voltage, the
reading should not exceed 27kV.
4.12.2 CRT filament voltage check
Receive A7 signal, set user control to “STANDARD” mode, use effective voltage meter to measure CRT
filament voltage, the reading should be (6.3±0.3) Vrms
4.12.3 X-ray protection check
1) Receive A7 signal, set user control to “STANDARD” mode.
2) Use voltameter to measure VD482 positive pole to GND voltage, the reading should be between 1.0
V~2.5 V.
3) Use 5.3V DC regulated voltage power with 1K resistor in series to touch TP1 (VD482 positive pole),
connect DC regulated voltage power negative pole to GND, X-Ray protection circuit should function,
at this time the TV set should be without raster, without sound. Disconnect the DC regulated voltage
power, picture and sound should restore to normal.
4.12.4 Picture and sound check
1) Receive standard TV signal.
2) Use picture control buttons to check color, contrast, brightness, sharpness, tint’s function.
3) Use sound control buttons to check volume control function.
4.12.5 Sub-brightness check
Receive A7 signal, set brightness to 75, contrast to 50, color to 0, sharpness to 50, picture left side 1-6
lattices slightly light up.
4.12.6 Color purity and convergence check (in normal way)
4.12.7 AV terminals IN/OUT check, S-VIDEO in check, Y,Cb,Cr in check.
4.12.8 Other buttons on the TV set and remote controller function check.
4.13 Degaussing
a) The unit has and auto degaussing circuit, the degaussing circuit works several seconds after turning
on TV
b) If you want to move TV or change the direction, turn off TV and ten minutes later the degaussing
circuit will work
c) For better degaussing effect, you can use magnetic eraser
d) Move the magnetic eraser clockwise before your TV, when it is 2m away from your TV, turn off the
magnetic eraser. If the effect is still not very good, you can adjust “color purity” and “convergence”
5
4.14 Color purity correction
a) Turn on your TV
b) At least 15 minutes later, use anti-magnetized coil for degaussing
c) Obtain maximum brightness and contrast
d) Select factory menu3 and adjust to let R and B be zero, then let only green raster appear on the
screen at the moment
e) Loosen screws of deflection yoke frame to let vertical green belt appear on screen only
f) Move the rubber wedge
g) Rotate along neck of picture tube and slide color-purity magnets until the green belt at the middle of
screen and is vertical at the same time
h) Slowly move the deflection yoke backward of forward until the whole green raster appears on screen,
tighten the screws of the deflection yoke
i) Check the color purity of red raster and blue raster
j) Adjust white balance again to obtain white raster
4.15 Convergence correction
4.15.1 Central convergence correction
a) Turn on your TV
b) At least 15 minutes later, receive square test pattern signal
c) Adjust brightness and contrast to get the best picture
d) Adjust the angle of two tetrode magnetic rings to let the red vertical line coincide with the blue
vertical line at middle of screen
e) Keep the angle unchanged, move the two tetrode magnetic rings at the same time to let the red and
blue horizontal lines coincide at middle of screen
f) Adjust two hexode magnetic rings to let the green line coincide with the mixed line of red and blue.
Adjust the angle between them will affect the vertical line, move them together will affect the
horizontal line.
g) Repeat d), e), f) and observe the movement of red, green and blue.
4.15.2 Ambient convergence correction
a) Turn on your TV
b) At least 15 minutes later, loosen the screws of the deflection yoke
c) Fixate the rubber wedge temporarily under the deflection yoke
d) Move the deflection yoke upward or downward to get best convergence, push the rubber wedge into
space between picture tube and deflection yoke to fixate the deflection yoke temporarily
e) Place the rubber wedge whose overlay paper has been removed at the bottom space
f) Move the deflection yoke left and right to get best convergence
g) Keep the condition unchanged, place another rubber wedge whose overlay paper has been
removed also at the upper space at the same time
h) Remove the interim rubber wedge, adhere it to picture tube and deflection yoke
i) After placing three rubber wedges, check all the convergence again
j) Stick three transparent viscous belts to the rubber wedge
4.16 Software adjustment instructions
4.16.1 instructions
This software contain MTS (option), English, Frence and Spanish of OSD, CCD and Parental Control
function, FS tuner mode, 181 channel.
6
4.16.2 turn on the unit in the STANDBY state
Press CH+/CH- buttons turn on in the STANDBY state.
4.16.3 Information of software version
Enter MEU9 of the factory menu in the top.
4.16.4 “STANDARD”, “COLORFUL” and “ SOFTNESS”
a).Enter MENU5 Mode of the factory menu
b).charge their for seemly analog quantity, then return standard option.
Chart 1 I
2
I
C standard UOC for export bus control adjustment i t em def ault setting
2
C TDA (NOM)8377-B-6NA E
2
PROM pre-set data
MI Items range Preset
M0 SUBCON 0-63 56(sub-contrast)
SUBCOL 0-63 56(sub-chroma)
SUBSHP 0-63 48(sub-acutance)
SUBTINT 0-63 31(sub-hue)
AKB ON/OFF ON
M1 V.SLOPE 0-63 36(field center adjustment)
V.SHIFT 0-63 32(field point adjustment)
V.SIZE 0-63 36(field amplitude adjustment)
V.SC 0-63 32(field line )
HSHIFT 0-63 32(line point adjustment)
PROGRAMA.NO 2(channel)
M2 AGCTAKEOVER 0-63 21(AGC adjustment)
SHIPPING 0(leave factory set)
M3 BT 0-100 75(adjust white balance of brightness)
CT 0-100 75(adjust white balance of brightness contrast)
SC 0
RB 0-63 32(red cut off level adjustment)
GB 0-63 32(green cut off level adjustment)
RD 0-63 32(red cut off level adjustment)
GD 0-63 32(green cut off level adjustment)
BD 0-63 32(blue cut off level adjustment)
SB 0-63 40(sub brightness adjustment)
M4 OSD.V.POSITION 0-63 15(OSD position)
OSD.H.POSITION 0-63 25(OSD H-position)
BTSC-MODE MONO/STEORO MONO(STEORO,SAP )
BTSC-ST 0-15 13
BTSC-SP 0-15 12
BTSC-L1 0-15 1
7
BTSC-A1 0-31 15
BTSC-A2 0-31 0
BTSC-TC 0-7 0
BTSC-STS 0-1
BTSC-ADJ
M5 MODE STANADARD(standard, soft, floweriness)
BRIGHT 0-100 75
COLOR 0-100 50
SCBRIGHT 0-63 23
YDELAYTV 0-15 12
YDELAYAV 0-15 12
M6 OSO 0-1 1(field over-scan switch)
AGCSPEED 0-3 1(AGC of speed)
FFI 0-1 0(IF PLL SPEED)
FMWS 0-1 1(frequency range of sound OFF=225KHZ,ON=450KHZ)
RP0 0-3 0(pre-shock and over-shock scale)
NTSCMATRIX USA/JAPAN USA
VOLPIN 0-1 0(1:push-pull output; 0: OC gate output.)
SOFT CLIP 0-3 3(white level limit)
PEAK WHITE 0-15 15(peak white limit)
CORING 0-1 0(coring noise reduction)
M7 AV2 0/1 1
SVHS 0/1 1
YUV 0/1 1
VOLADJPOING 1(volume value have:1,25,50,75)
VOLVALUE 20(volume curve value:20,60,75,90)
M8 CATHOOELEVEL 0-15 7(cathode level)
UOCVOLUME 0/1 0(0:PWM terminal control; 1:UOC sound amplitude
FMATT 0-63 45(UOC sound output of amplitude) BTSC : 38
COMBFILTRE 0-1 0(N comb filter)
HEADPHONE 0-1 0(earphone function selection)
VM OPTION 0/1 0(VM function selection)
FRANCE 0/1 1 French
SPANISH 0/1 1 Spaish
M9 NOM8377-B-6NA
STARTON 0-2 2(turn on)
CONTRAST
0-100 75
0
control of inside)
8
STARTTIME 6-15 8(turn on time)
IF OFFSET 0-63 32(IF compensate)
TUNER OPTION 0-2 0(BXATB011F---X/ BXATB108F---K) 1 (BXATB017F---K)
2(XXX)
GAME 0/1 0
GALENDA 0/1 0
9
Block diagram
rCb
DY
S
F
S
Speaker
A101 Z301 V801
TDA8377
TUNER
AN702
KA5Q0765
T501
POWER
UNIT
video
180V
+13.5
-13V
Y
C
CRT
BOARD
CREEN
OCU
SAW
V352 N121
S
TRAP
24C08
110V
26V
12V
8V
5V
3.3V
video
bus
IF IN Y IN
RF AGC V IN
U IN
CVBSINT
CHROMA
IFVO OUT
CVBS/Y IN
SDA
SCL
AUDIO OUT IK
RGB OUT
V OUT H OUT
V IN
STV9302A
V OUT
H IN
H OUT
TT2140
T451
H OUT
video
audio
CRT
video
BU4052
audio
N801
video
audio
Y
C
BU4052
AN7522
Vo
V2i
V1i
S-VHS
ARo
ALo
ARi2
ARi1
ALi2
ALi1
L
OUT1+
OUT1-
R
OUT2OUT2+
10
MAIN IC 8377:
ICs functional description
UOC TDA(OM)8377
SYMBOL PIN DESCRIPTION
STAND BY output. 1 In STAND BY mode, high level (Power OFF).
For Power ON this pin will be reduced to low.
SCL 2 I2C-bus clock line
SDA 3 I2C-bus data line
TUNING 4 NC
P3.0/NTSC SW 5
KEY 6 Control keys input
VOL 7 Sound Volume control PWM output
MUTE 8 Sound mute output
VSSC/P 9 Digit ground for µ-controller core and periphery
BAND1 10
BAND2 11
VSSA 12 Analog ground of teletext decoder and digital ground of
SECPLL 13
VP2 14 2nd supply voltage TV-processor(+8V)
NC
NC
NC
TV-processor
PLL decoupling
11
DECDIG 15 decoupling digital supply of TV-processor
PH2LF 16 Phase-2 filter
PH1LF 17 Phase-1 filter
GND3 18 Ground 3 for TV-processor
DECBG 19 Band gap decoupling
AVL/EWD 20 Automatic volume leveling /EAST-WEST drive output
VDRB 21 Vertical drive B output
VDRA 22 Vertical drive A output
IFIN1 23 IF input 1
IFIN2 24 IF input 2
IREF 25 Reference current input
VSC 26 Vertical sawtooth capacitor
TUNER AGC 27 Tuner AGC output
AUDEEM/SIFIN1 *1 28 Audio deemphasis or SIF input
DECSDEM/SIFIN2 29 decoupling sound demodulator or SIF input 2
GND2 30 ground 2 for TV processor
SNDPLL/SIFAGC *1 31 narrow band PLL filter or AGC sound IF
AVL/SNDIF/REF0/
AMOUT *1
32 Automatic Volume Levelling / sound IF input / subcarrier
reference output / audio
deemphasis
HOUT 33 horizontal output
FBISO 34 flyback input/sandcastle output
AUDEXT/QSSO/
35 external audio output / QSS intercarrier out
AMOUT *1
EHTO 36 EHT/overvoltage protection input
PLL IF 37 IF-PLL loop filter
IFVO/SVO 38 IF video output / selected CVBS output
VP1 39 supply voltage TV processor
CVBS INT 40 internal CVBS input
GND1 41 ground for TV processor
CVBS/Y 42 CVBS/Y input
CHROMA 43 C input
AUDOUT/AMOUT *1 44 audio output /AM audio output (volume controlled)
INSSW2 45 2nd RGB / YUV insertion input
R2/VIN 46 2nd R input / V (R-Y) input / PR input
G2/YIN 47 2nd G input / Y input
B2/UIN 48 2nd B input / U (B-Y) input / PB input
BCLIN 49 beam current limiter input
BLKIN 50 black current input / V-guard input
RO 51 Red output
GO 52 Green output
BO 53 Blue output
VDDA 54 analog supply of Closed Caption decoder and digital supply of
12
TV-processor (3.3 V)
VPE 55 OTP Programming Voltage
VDDC 56 digital supply to core (3.3 V)
OSCGND 57 oscillator ground supply
XTALIN 58 crystal oscillator input
XTALOUT 59 crystal oscillator output
RESET 60 reset
VDDP 61 digital supply to periphery (+3.3 V)
P1.0/INT1 62 TV/AV (AV1) / AV2 /S-VHS mode Output.
P1.1/T0 63 TV/AV (AV1) / AV2 /S-VHS mode Output.
P1.2/INT0 64 Remote control signal input.
AN7522/AN17821A Function : audio output
Symbol PIN Function Symbol PIN Function
Vcc 1 Power supply GND 7 ground
Out 1 (+) 2 Ch 1 output (+) In 2 8 Ch 2 input
GND(out 1) 3 Ch 1Ground VOL 9 Volume Control
Out 1 (-) 4 Ch 1 output (-) Out 2 (-) 10 Ch 2 output (-)
Standby 5 Mute input GND(out 2) 11 Ch 2 Ground
In 1 6 Ch 1 input Out 2 (+) 12 Ch 2 output (+)
STV9302A/LA78040 Function : vertical output
Symbol PIN Function Symbol PIN Function
INV IN 1 Input V OUT 5 Vertical output
VCC1 2 Power VCC2 6 Output power
supply
PUMP UP 3 Pump up power NON INV IN 7 Negative feedback
GND 4 Ground
IC voltages
TDA(OM)8377
PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
V 2.8 3.8 3.6 3.3 3.5 3.5 0.1 0.1 0 5.4 0.1 0 2.3 8 5 3
PIN 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
V 4 0 4 0.9 0.7 0.8 1.9 1.9 3.9 3.8 1.6 3.2 3.4 0 2.4 0.1
PIN 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
V 0.6 0.5 3.7 1.7 2.4 3.1 8 3.8 0 3.4 1.5 3.6 2.3 2.6 2.6 2.6
PIN 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
V 2.3 7.2 2.7 2.7 2.7 3.5 0 3.5 0.1 1.7 1.8 0 3.5 0.1 0.1 5
STV9302A/LA78040
PIN 1 2 3 4 5 6 7
V 0.7 15 -12 -15 0.3 15.9 -0.07
13
AN 7522/AN17821A
PIN 1 2 3 4 5 6 7 8 9 10 11 12
V 12 7 0 7 3.3 1.4 0 1.4 0 7 0 7
6. Test point Waveforms
2.6Vpp
H
TDA8377 PIN38
95Vpp
H
1Vpp
TDA8377 PIN21
V
H H
1.2Vpp
H
TDA8377 PIN40
95Vpp
H H
CRT KG CRT KR
0.8Vpp
V
TDA8377 PIN22
300Vpp 22Vpp
T501 PIN7
3.8Vpp
H
TDA8377 PIN53
95Vpp
CRT KB
TDA8377 PIN59
2.5Vpp
H H
TDA8377 PIN52 TDA8377 PIN51
0.9Vpp
H
TDA8377 PIN33
2.7Vpp
H
V451 B
2.5Vpp
5Vpp
H
TDA8377 PIN34
920Vpp
H
V451 C
14
Wiring diagram
15
PART LIST
PART# DESCRIPTION LOCA.NO.
203-TK20500-12 TS2050J, PRIMA BRAND JENSEN,N100-TK20500-01 TK2050
123-30001-04 TWIST WIRE
655-62101-01 (6-PINS) LEAD WITH HOUSING
700-60151-00 LED LED COLUMN
700-60152-00 LED LED COLUMN
742-30005-09 LINE TIE
742-30006-09 GRADING TIE
742-30029-00 POWER CORD CLASPER
742-30032-00 TIE
742-30032-00 TIE
742-30032-00 TIE
742-30038-00 TIE
770-37112-40 RV105 12X0.15 370mm BLACK
780-10915-J40A BACK CABINET (HIPS V0 MOLD GREY )
880-10205-802A BACK PLATE (TS2050J,JENSEN)
808-70239-00 EVA GLUE 150X50X1
838-10012-00 BRAIDED WIARE SPRING
851-23010-11 SCREW SJ2824 ST3X10C-D.Zn
851-23012-14 SCREW SJ2824 ST3X12C-Y
851-24016-14 SCREW SJ2824 ST4X16C-Y
851-24020-11 SCREW SJ2824 ST4X20C-D.Zn
851-24020-14 SCREW SJ2824 ST4X20C-Y
851-53010-11 SCREW SJ2825 ST3X10C-D.Zn
851-53012-14 SCREW SJ2825 ST3X12C-D.Zn
851-53012-14 SCREW SJ2825 ST3X12C-D.Zn
851-53018-11 SCREW SJ2825 ST3X18C-D.Zn
855-A0029-00 SCREW ST4X14
855-96024-31 COMPOSE SCREW ST6X24BT-D.Zn
857-10002-09 COTTON FLANNEL
857-10004-00 COTTON FLANNEL
863-80747-00 POLY FOAM (TOP ) ( SMALL )
863-80748-00 POLY FOAM (BOTTOM ) ( SMALL )
868-10107-00 CUSHION
868-20007-00 SLEEVE
868-20142-00 RUBBER WASHER (δ1.5)
868-20465-00 CUSHION
868-20472-00D CRT FIXER
868-20491-00 CRT SUPPORT
870-20845-00 LEFT LEADING TRACK
870-20846-00 RIGHT LEADING TRACK
881-60085 BLANK WARNING LABEL
887-20044-01 POWER CORD COVER
887-20171-00 PALSTIC BAG 70-500-0.06
887-21096-P0 PE/PEARL COTTONPALSTIC BAG 1100X1000
887-21135-00 CLASPER PALSTIC BAG 230X330X0.1
335-21225-00U CRT A51KQK99X01THICK !
602-TK2026-01 SCHEMATIC DIAGRAM
604-TK20506-02 OWNER'S MANUALJENSEN MTS NEWCPU
611-C50X0J0HC
FRONT CABINET ASS'Y (HIPS V0 SILVER WHITE 03
808-6B758-04 INTERFACE SPACE PLATE (SILK-SCREEN )
880-10423-01
FRONT LOGO (JENSEN, SILVERY GLOSS GREY 10
881-63030-00A POWER SYMBOL LABEL ( JENSEN)
881-63758-00 BAR CODE LABEL (69020712050)
881-80666-00 REGISTER CARD ( JENSEN AMERICA )
881-80679-00 SERVICE CARD ( AMERICA 20-24 CRT)
886-31132-121 CARTON BOX (TS2050J,JENSEN)
887-21135-00 CLASPER PALSTIC BAG 230X330X0.1
887-21135-02 CLASPER PALSTIC BAG 230X330X0.1
615-20429-00 SPEAKER ASS'Y
384-40308-40 SPEAKER ST511-02
655-51201-185 (5-PINS) LEAD WITH HOUSING
851-53012-11 SCREW SJ2825 ST3X12C-D.Zn
868-20217-00 WASHER
870-20849-00 SPEAKER BRACKET
667-M24501-05 STANDBY KEY BOARD ASS'Y
360-10001-00 TACT SWITCH KFC-A06-4X4.5X5B
665-2E301-24 (2-PINS) LEAD WITH HOUSING
782-13Y90-050A BUTTON PCB
667-TKP50-01C MAIN PCB ASS'Y
667-TKP50-01C\ MAIN PCB ASS'Y (MANUAL INSERTION )
364-32101-00 2-PINS CONNECTORS TJC3-02A
XS702
464-6D647-M0 ELECTROLYTIC CAPACITOR CD110-16V-47uF-M C121
467-2E120-H0 METAL RESISTOR 1/2W-200Ω-JL R407
491-70240-02 POWER CORD UL !
535-TK2050-02W OUTSOURCING ASS'Y
BT-0330D---CH
RC.TRANSMIT(PRIMA) REMOTE CONTROL ( JENSEN ) ZZ030
BXATB017F---K TUNER(ET-5T5E-AF108) A101
CAF104K1-H-FC 50V0.1u C326 C338 C365
C411 C511
CAF224K1-H-FC 50V0.22u C331 C334 C404
CCF330J1CA-FN 50V33P C761 C762
CED102M1ACHNP 25V1000u C522
CED222M2ACKNP 25V2200u C524
CED471M1ACENP 25V470u C161
CEE331M1ACFNP 35V330u C530
CEH100M1ACENP 160V10u C458
CEH221M2ECLNP 160V220u C528B
CEJ221M3AEHNM 200V220u C507
CEK100M1ACHNP 250V10u C477 C941
CKF472K1BA-FN 50V4700P C324 C336
CKMX102M301ND AC400V1000P C515A
CKMX471K301ND AC400V470P C515 C598 C598B
CKP101K1BA-FD 500V100P C482
CKW102K2BJ-ND 1KV1000P C503 C504
C505 C506
CKW471K2RA-ND 1KV470P C529
CKX102P2EJ-ND 2KV1000P C512 C943
CKX331K2RA-ND 2KV330P C456
CKX471K2RA-ND 2KV470P C543
CKX681K2RA-ND 2KV680P C527
CMNX224M801NP AC275V0.22u C501 C502
CMZ752J7-H-NE 1.6KV7500p C455
CNJ394J9-H-NE 200V0.39u C467
DH24R5M001-NC PTC4.5ohm(3 END ) PS501
DN15R0M001-NN NTCMF72-5D13 5ohm R502
DRRGP10D---TD RGP10D VD401 VD436
VD470 VD471
DRRGP10D---TD RGP10D VD510 VD512
VD522 VD525
DRRGP10D---TD RGP10D VD581 VD482A
DRRGP10J---TD RGP10J VD472 VD524
DRRGP15D---TD RGP15D VD521 VD543
DRTVR4J----ND TVR4J VD503 VD504 VD505
VD506 VD508
DZHZ12A2---TH HZ12A2 VD588
DZHZ3C3----TQ HZ3C3 VD564
DZHZ4A2----TQ HZ4A2 VD509
DZHZ5C1----TQ HZ5C1 VD300A
DZHZ7C1----TQ HZ7C1 VD381 VD382 VD383
DZHZ9A3----TQ HZ9A3 VD483 VD822
VD941 VD861A
FBA3004S02U-A FUSE 3A RT1-20 UL F501
GAAV2001----A 2S SOCKET(BIG ) XR502
GABV2001----N 2S SOCKET(MIDDLE ) XS502
)
)
GACV5001----A 5S SOCKET(SMALL XH) XS161
GACV6001----A 6S SOCKET XS895
GBAVL007----A CRT SOCKET THICK GZS10-2-108 XS901
GBBB9-06----8 AVSOCKET(AV16-09-004) XS801
GBCH5001----Y S END XS861
HAA0004-----G SMIT-SS-112DM(27ohm) RL581
JW4451-J001-A 4P LINE(450mm D2-D2) XS402(XS402→XS902
JW5431-J132-A 5P LINE(E3D 430mm) XS903(XS903→XS301
LEA001-5---NJ M-COIL( FERRITE BEAD ) L450 L505
LEE004-----NJ FERRITE BEAD (6*5*1.5mm) ZD524+ ZD524-
LF-037-2---NJ LINE COIL ROW LINELX37 L452
LG-003-----NL LINE FILTER(4MH) L502
LG-013-----NL LINE FILTER10*12.5 L501
LM-067-----NG DEGAUS COIL L511
M90X0003---91 INSULATING CUSHION 18*13 D4.8 Z1
MB0X0011---G8 FUSE SOCKET(FUSE HOLDER ) F501A F501B
MB1X0040---BF 12V RADIATOR H-N505
MB1X0114---BF 5V RADIATOR (CUBA) H-N503
MB1X0196---BF ROW RADIATOR H-V451
MB1X0228---BG SOUND RADIATOR H-N161
MB1X0269---BF POWER RADIATOR H-N501
MG3X0036---D7 INSULATING WASHER (D9) Z2
MG3X0037---D7 INSULATING WASHER (D9) Z3
NAN17821A--N- AN17821A N161
NAT24C08---N- AT24C08 N702
NCW574CS---N- CW574CS N703
NHEF4052---BP HEF4052 N121 N801
NK1010B----N- K1010B N504
NKA431AZ---F- KA431AZ V540
NKA5Q0765H-N- KA5Q0765H N501
NMC7805CT--N- MC7805CT N505
NMC7808CT--N- MC7808CT N503
NOM8377-B-6NC NOM8377-B-6NC N301
NOM8377-B-9NA OM8377PS/N3/2 N301
NSTV9302A--N- STV9302A N401
PX20074----3Q MAIN+CRTPCB ZZ60
Q2PA1015-GNF- 2PA1015G V171 V581
Q2PA1015-GNF- 2PA1015G V492
Q2PC1815-GNF- 2PC1815 G V121 V122
V173 V351
Q2PC1815-GNF- 2PC1815 G V352 V395
V504 V801
Q2PC1815-GNF- 2PC1815G V491
R
B
Q2SB1443--NN- 2SB1443 TV2 Q V542
QBF421----NF- BF421 V913 V923 V933
QBF422----NF- BF422 V912 V922 V932
QKSC1674C-NN- KSC1674C V308
QKSC2330-YNN- KSC2330 V911 V921 V931
QKSC2383-ONF- KSC2383O V450
QTT2140---BN- TT2140 V451
RDD102J-NACTD 1/2W 1K R453
RDD683J-NACTD 1/2W 68K R507 R508
RFER27J5ACDNF 1W 0.27 R555 R565 R566
RFER47J5ACDNF 1W 0.47 R165 R470
R472 R545
RGDX126K-03NA 1/2W 12M(PMSR34015126) R519
RGDX152K-03NZ 1/2W 1.5K R918 R928 R938
RJB393F-NAATD 1/6W 39K R411
RSE102J4ACCND 1W 1K R466
RSE1R2J5DCCND 1W 1.2 R406
RSE220J5ACCND 1W 22 R300A
RSF103J5ACDND 2W 10K R467 R703
RSF103J7ACDND 2W 10K R915 R925 R935
RSF153J7ACDND 2W 15K R556
RSF1R5J7ACDND 2W 1.5 R480
RSF271J7ACDND 2W 270 R454
RSF560J5ACDND 2W 56 R530
RSF5R6J5ACDND 2W 5.6 R941
RWH3R9K3AK-N
5W 3.9 R458
SCA-25016FE-H GB818 M2.5*12 SN401
SFAC30010FE1H SJ2836-87(M3*10.I) SN503 SN161A SN161
SFAC30012FE1H SJ2836-87(M3*12.I) S-N501 S-V451
SKA-308R0FE-H GB845-78 ST3*8 S-N505 S-V432
SXN1A25--FF-H M2.5NUT zz360
SXN1A30--FF-H M3(NUT ) NN161A NN161B
SXN1A30--FF-H M3(NUT ) N-N501 N-N503
N-V451
SXW1A25--FE-H GB97.1 D2.5 WASHER ZN401
TD-0004----0L H-DRIVER( ROW PUSH) T450
TF-0133U---2U F.B.T(BSC24-01N4004U) T451
TM-0105U---0L CON.TRANS(SPT4001 UL) T501
VDAAA203A001C 20KB VR501
XFS031-----NB SAWF M1967 Z301
XTC009-----NP T4.5MTRAP FILTER Z351
XX-021-----NC CR.OSC12M(18P) X761
340-00001-00 DIODE 1N4148 VD911
364-32101-00 2-PINS CONNECTORS TJC3-02A XS702A
364-34101-00 4-PINS CONNECTORS TJC3-04A XS701
364-36102-00 6-PINS CONNECTORS TJC2-6A XS403
459-B222M-20 CERAMIC CAPACITOR ECK-DNS222MEX !
459-2133K-90 CERAMIC CAPACITOR RBU07SL331K-H46CA
C911
459-2147H-90 CERAMIC CAPACITOR CC1-12-SL-63V-471J C732
464-6D610-M0 ELECTROLYTIC CAPACITOR CD110-16V-10uF-M C322
464-6D610-M0 ELECTROLYTIC CAPACITOR CD110-16V-10uF-M C751
464-6D647-M0 ELECTROLYTIC CAPACITOR CD110-16V-47uF-M C723A
464-6D647-M0 ELECTROLYTIC CAPACITOR CD110-16V-47uF-M C815
464-6D710-M0 ELECTROLYTIC CAPACITOR CD110-16V-100uF-M C743
464-6D733-M0 ELECTROLYTIC CAPACITOR CD110-16V-330uF-M C581
464-60510-M0 ELECTROLYTIC CAPACITOR CD110-50V-1uF-M C841
464-60522-M0 ELECTROLYTIC CAPACITOR CD110-50V-2.2uF-M C755
464-60547-M0 ELECTROLYTIC CAPACITOR CD110-50V-4.7uF-M C340
464-60547-M0 ELECTROLYTIC CAPACITOR CD110-50V-4.7uF-M C340
467-1C022-H0 CARBON RESISTOR 1/6W-22Ω-J R914
467-1C130-H0 CARBON RESISTOR 1/6W-300Ω-J R913
467-1C310-H0 CARBON RESISTOR 1/6W-10K-J C535
467-2D218-G0 METAL RESISTOR 1/4W-1.8K-G R403
467-2D218-G0 METAL RESISTOR 1/4W-1.8K-G R405
467-2E210-H0 METAL RESISTOR 1/2W-1kΩ-JL R460
467-8E522-H0U SOLID RESISTOR 1/2W-2.2MΩ-JL ! R588
471-2001K-00 PEAKING COIL SPT0305-1R0K-5 L302
475-25451-00 CERAMIC TRAP FILTER XT4.5MB Z351
666-12301-00 FERRITE BEAD TY23X13.5X6
666-13501-00 FERRITE BEAD TBL-P# 2122651A
V451-C
666-13501-00 FERRITE BEAD TBL-P# 2122651A V451-B
681-40003-00 OK LABEL
742-30005-09 LINE TIE
742-30005-09 LINE TIE
775-60044-00 SOCKET PIN RT-01T-1.3B
TP2
775-60044-00 SOCKET PIN RT-01T-1.3B TP3
881-60074-00 HIGH VOLTAGE WARNING LABEL
998 JUMPER WIRE
W025
742-30005-09 LINE TIE
775-10054-00 SOLDERING BLADE
L
775-10054-00 SOLDERING BLADE N
998 JUMPER WIRE W101A
998 JUMPER WIRE W102A
667-TKP50-01C* MAIN PCB ASS'Y (AUTOMATIC INSERTION )
459-2133K-902 CERAMIC CAPACITOR RBU07SL331K-H46CA C323
462-B0233-H02 POLYESTER CAPACITOR CL21X-50V-3300PF-J C321
462-00256-H02 POLYESTER CAPACITOR CL11-100V-5600PF-J C154
462-00256-H02 POLYESTER CAPACITOR CL11-100V-5600PF-J C158
464-6D647-M02 ELECTROLYTIC CAPACITOR CD110-16V-47uF-M C123
467-1C033-H03 CARBON RESISTOR 1/6W-33Ω-J R398
467-1C047-H03 CARBON RESISTOR 1/6W-47Ω-J R921
467-1C047-H03 CARBON RESISTOR 1/6W-47Ω-J R931
467-1C215-H03 CARBON RESISTOR 1/6W-1.5K-J R397
467-1C256-H03 CARBON RESISTOR 1/6W-5.6K-J R481
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R395
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R396
340-00001-003 DIODE 1N4148 VD171
340-00001-003 DIODE 1N4148 VD461
340-00001-003 DIODE 1N4148 VD462
340-00001-003 DIODE 1N4148 VD511
340-00001-003 DIODE 1N4148 VD544
340-00001-003 DIODE 1N4148 VD561
340-00001-003 DIODE 1N4148 VD562
340-00001-003 DIODE 1N4148 VD734
340-00001-003 DIODE 1N4148 VD921
340-00001-003 DIODE 1N4148 VD931
340-00001-003 DIODE 1N4148 VD582
340-51790-003 *ZENER DIODE HZ18C2 VD481
459-2133K-902 CERAMIC CAPACITOR RBU07SL331K-H46CA C921
459-2133K-902 CERAMIC CAPACITOR RBU07SL331K-H46CA C931
459-2147H-902 CERAMIC CAPACITOR CC1-12-SL-63V-471J C803
459-2147H-902 CERAMIC CAPACITOR CC1-12-SL-63V-471J C805
459-2147H-902 CERAMIC CAPACITOR CC1-12-SL-63V-471J C812
459-2147H-902 CERAMIC CAPACITOR CC1-12-SL-63V-471J C814
459-2147H-902 CERAMIC CAPACITOR CC1-12-SL-63V-471J C824
459-2147H-902 CERAMIC CAPACITOR CC1-12-SL-63V-471J C826
459-2156K-002 CERAMIC CAPACITOR CT1-06-2B4-63V-561K C381
459-2210K-002 CERAMIC CAPACITOR CK45-B1H102KYR C308
459-2210K-002 CERAMIC CAPACITOR CK45-B1H102KYR C311
459-2210K-002 CERAMIC CAPACITOR CK45-B1H102KYR C401
459-2210K-002 CERAMIC CAPACITOR CK45-B1H102KYR C402
459-2210K-002 CERAMIC CAPACITOR CK45-B1H102KYR C721
459-2210K-002 CERAMIC CAPACITOR CK45-B1H102KYR C861
459-2222K-002 CERAMIC CAPACITOR CT1-08-2B4-63V-222K C335
459-2310R-002 CERAMIC CAPACITOR CK45-F1H103ZYR C309
459-2310R-002 CERAMIC CAPACITOR CK45-F1H103ZYR C313
459-2310R-002 CERAMIC CAPACITOR CK45-F1H103ZYR C332
459-2310R-002 CERAMIC CAPACITOR CK45-F1H103ZYR C362
459-2310R-002 CERAMIC CAPACITOR CK45-F1H103ZYR C472
459-2310R-002 CERAMIC CAPACITOR CK45-F1H103ZYR C475
459-2310R-002 CERAMIC CAPACITOR CK45-F1H103ZYR C723
459-2310R-002 CERAMIC CAPACITOR CK45-F1H103ZYR C744
459-2310R-002 CERAMIC CAPACITOR CK45-F1H103ZYR C752
459-2310R-002 CERAMIC CAPACITOR CK45-F1H103ZYR C756
459-2310R-002 CERAMIC CAPACITOR CK45-F1H103ZYR C399
459-2410R-002 CERAMIC CAPACITOR DD308-63F104Z50 C302
459-2410R-002 CERAMIC CAPACITOR DD308-63F104Z50 C703A
459-5122K-002 CERAMIC CAPACITOR RQC05B221K-6H46UA C405
459-5147K-002 CERAMIC CAPACITOR RQC05B471K-H46CA C513
459-5210K-002 CERAMIC CAPACITOR CK45-B2H102KYR C452
459-5239K-002 CERAMIC CAPACITOR CK45-B2H392KYR C451
462-B0422-H02 POLYESTER CAPACITOR CL21X-50V-0.22uF-J C491
462-00333-H02 POLYESTER CAPACITOR CL11-100V-0.033uF-J C403
462-00333-H02 POLYESTER CAPACITOR CL11-100V-0.033uF-J C510
462-00333-H02 POLYESTER CAPACITOR CL11-100V-0.033uF-J C544
462-00410-H02 POLYESTER CAPACITOR CL11-100V-0.1uF-J C460
464-6C710-M02 ELECTROLYTIC CAPACITOR CD110-10V-100uF-M C301
464-6C710-M02 ELECTROLYTIC CAPACITOR CD110-10V-100uF-M C548
464-6D610-M02 ELECTROLYTIC CAPACITOR CD110-16V-10uF-M C163A
464-6D610-M02 ELECTROLYTIC CAPACITOR CD110-16V-10uF-M C172
464-6D610-M02 ELECTROLYTIC CAPACITOR CD110-16V-10uF-M C363
464-6D610-M02 ELECTROLYTIC CAPACITOR CD110-16V-10uF-M C364
464-6D610-M02 ELECTROLYTIC CAPACITOR CD110-16V-10uF-M C367
464-6D610-M02 ELECTROLYTIC CAPACITOR CD110-16V-10uF-M C807
464-6D622-M02 ELECTROLYTIC CAPACITOR CD110-16V-22uF-M C745
464-6D622-M02 ELECTROLYTIC CAPACITOR CD110-16V-22uF-M C352
464-6D647-M02 ELECTROLYTIC CAPACITOR CD110-16V-47uF-M C116
464-6D647-M02 ELECTROLYTIC CAPACITOR CD110-16V-47uF-M C171
464-6D647-M02 ELECTROLYTIC CAPACITOR CD110-16V-47uF-M C333
464-6D647-M02 ELECTROLYTIC CAPACITOR CD110-16V-47uF-M C561
464-6D647-M02 ELECTROLYTIC CAPACITOR CD110-16V-47uF-M C811
464-6D647-M02 ELECTROLYTIC CAPACITOR CD110-16V-47uF-M C823
464-6D647-M02 ELECTROLYTIC CAPACITOR CD110-16V-47uF-M C871
464-6D647-M02 ELECTROLYTIC CAPACITOR CD110-16V-47uF-M C804
464-6D647-M02 ELECTROLYTIC CAPACITOR CD110-16V-47uF-M C806
464-6D647-M02 ELECTROLYTIC CAPACITOR CD110-16V-47uF-M C813
464-6D647-M02 ELECTROLYTIC CAPACITOR CD110-16V-47uF-M C825
464-6D647-M02 ELECTROLYTIC CAPACITOR CD110-16V-47uF-M C827
464-6D710-M02 ELECTROLYTIC CAPACITOR CD110-16V-100uF-M C361
464-6D747-M02 ELECTROLYTIC CAPACITOR CD110-16V-470uF-M C525
464-6D747-M02 ELECTROLYTIC CAPACITOR CD110-16V-470uF-M C532
464-6D747-M02 ELECTROLYTIC CAPACITOR CD110-16V-470uF-M C801
464-6E710-M02 ELECTROLYTIC CAPACITOR CD110-25V-100uF-M C471A
464-6E710-M02 ELECTROLYTIC CAPACITOR CD110-25V-100uF-M C474A
464-6E722-M02 ELECTROLYTIC CAPACITOR CD110-25V-220uF-M C471
464-6E722-M02 ELECTROLYTIC CAPACITOR CD110-25V-220uF-M C474
464-6F647-M02 ELECTROLYTIC CAPACITOR CD110-35V-47uF-M C453
464-6F647-M02 ELECTROLYTIC CAPACITOR CD110-35V-47uF-M C460A
464-6F710-M02 ELECTROLYTIC CAPACITOR CD110-35V-100uF-M C406
464-60447-M02 ELECTROLYTIC CAPACITOR CD110-50V-0.47uF-M C372
464-60447-M02 ELECTROLYTIC CAPACITOR CD110-50V-0.47uF-M C374
464-60510-M02 ELECTROLYTIC CAPACITOR CD110-50V-1uF-M C163
464-60510-M02 ELECTROLYTIC CAPACITOR CD110-50V-1uF-M C337
464-60510-M02 ELECTROLYTIC CAPACITOR CD110-50V-1uF-M C862
464-60522-M02 ELECTROLYTIC CAPACITOR CD110-50V-2.2uF-M C339
464-60547-M02 ELECTROLYTIC CAPACITOR CD110-50V-4.7uF-M C325
464-60547-M02 ELECTROLYTIC CAPACITOR CD110-50V-4.7uF-M C464
464-60547-M02 ELECTROLYTIC CAPACITOR CD110-50V-4.7uF-M C481
464-60547-M02 ELECTROLYTIC CAPACITOR CD110-50V-4.7uF-M C153
464-60547-M02 ELECTROLYTIC CAPACITOR CD110-50V-4.7uF-M C157
464-60547-M02 ELECTROLYTIC CAPACITOR CD110-50V-4.7uF-M C307
464-60622-M02 ELECTROLYTIC CAPACITOR CD110-50V-22uF-M C703
464-60647-M02 ELECTROLYTIC CAPACITOR CD110-50V-47uF-M C462
464-60647-M02 ELECTROLYTIC CAPACITOR CD110-50V-47uF-M C517
464-62547-M02 ELECTROLYTIC CAPACITOR CD288-160V-4.7uF-M C466
467-1C022-H03 CARBON RESISTOR 1/6W-22Ω-J R924
467-1C022-H03 CARBON RESISTOR 1/6W-22Ω-J R934
467-1C033-H03 CARBON RESISTOR 1/6W-33Ω-J R806
467-1C047-H03 CARBON RESISTOR 1/6W-47Ω-J R368
467-1C047-H03 CARBON RESISTOR 1/6W-47Ω-J R708
467-1C047-H03 CARBON RESISTOR 1/6W-47Ω-J R911
467-1C056-H03 CARBON RESISTOR 1/6W-56Ω-J R355
467-1C056-H03 CARBON RESISTOR 1/6W-56Ω-J R801
467-1C068-H03 CARBON RESISTOR 1/6W-68Ω-J R304
467-1C082-H03 CARBON RESISTOR 1/6W-82Ω-J R313
467-1C082-H03 CARBON RESISTOR 1/6W-82Ω-J R815
467-1C082-H03 CARBON RESISTOR 1/6W-82Ω-J R824
467-1C110-H03 CARBON RESISTOR 1/6W-100Ω-J R301A
467-1C110-H03 CARBON RESISTOR 1/6W-100Ω-J R302A
467-1C110-H03 CARBON RESISTOR 1/6W-100Ω-J R363
467-1C110-H03 CARBON RESISTOR 1/6W-100Ω-J R365
467-1C110-H03 CARBON RESISTOR 1/6W-100Ω-J R366
467-1C110-H03 CARBON RESISTOR 1/6W-100Ω-J R381
467-1C110-H03 CARBON RESISTOR 1/6W-100Ω-J R382
467-1C110-H03 CARBON RESISTOR 1/6W-100Ω-J R383
467-1C110-H03 CARBON RESISTOR 1/6W-100Ω-J R401
467-1C110-H03 CARBON RESISTOR 1/6W-100Ω-J R402
467-1C110-H03 CARBON RESISTOR 1/6W-100Ω-J R452
467-1C110-H03 CARBON RESISTOR 1/6W-100Ω-J R723
467-1C110-H03 CARBON RESISTOR 1/6W-100Ω-J R724
467-1C110-H03 CARBON RESISTOR 1/6W-100Ω-J R743
467-1C110-H03 CARBON RESISTOR 1/6W-100Ω-J R861
467-1C110-H03 CARBON RESISTOR 1/6W-100Ω-J R862
467-1C110-H03 CARBON RESISTOR 1/6W-100Ω-J R354
467-1C115-H03 CARBON RESISTOR 1/6W-150Ω-J R815A
467-1C115-H03 CARBON RESISTOR 1/6W-150Ω-J R848
467-1C115-H03 CARBON RESISTOR 1/6W-150Ω-J R852
467-1C115-H03 CARBON RESISTOR 1/6W-150Ω-J R304A
467-1C118-H03 CARBON RESISTOR 1/6W-180Ω-J R353
467-1C118-H03 CARBON RESISTOR 1/6W-180Ω-J R805
467-1C122-H03 CARBON RESISTOR 1/6W-220Ω-J R311
467-1C122-H03 CARBON RESISTOR 1/6W-220Ω-J R917
467-1C122-H03 CARBON RESISTOR 1/6W-220Ω-J R927
467-1C122-H03 CARBON RESISTOR 1/6W-220Ω-J R937
467-1C130-H03 CARBON RESISTOR 1/6W-300Ω-J R923
467-1C130-H03 CARBON RESISTOR 1/6W-300Ω-J R933
467-1C133-H03 CARBON RESISTOR 1/6W-330Ω-J R916
467-1C133-H03 CARBON RESISTOR 1/6W-330Ω-J R926
467-1C133-H03 CARBON RESISTOR 1/6W-330Ω-J R936
467-1C139-H03 CARBON RESISTOR 1/6W-390Ω-J R322
467-1C139-H03 CARBON RESISTOR 1/6W-390Ω-J R775
467-1C147-H03 CARBON RESISTOR 1/6W-470Ω-J R308
467-1C168-H03 CARBON RESISTOR 1/6W-680Ω-J R316
467-1C210-H03 CARBON RESISTOR 1/6W-1K-J R128
467-1C210-H03 CARBON RESISTOR 1/6W-1K-J R129
467-1C210-H03 CARBON RESISTOR 1/6W-1K-J R369
467-1C210-H03 CARBON RESISTOR 1/6W-1K-J R380
467-1C210-H03 CARBON RESISTOR 1/6W-1K-J R464
467-1C210-H03 CARBON RESISTOR 1/6W-1K-J R531
467-1C210-H03 CARBON RESISTOR 1/6W-1K-J R541
467-1C210-H03 CARBON RESISTOR 1/6W-1K-J R544
467-1C210-H03 CARBON RESISTOR 1/6W-1K-J R734
467-1C210-H03 CARBON RESISTOR 1/6W-1K-J R802
467-1C210-H03 CARBON RESISTOR 1/6W-1K-J R803
467-1C210-H03 CARBON RESISTOR 1/6W-1K-J R816
467-1C210-H03 CARBON RESISTOR 1/6W-1K-J R818
467-1C210-H03 CARBON RESISTOR 1/6W-1K-J R825
467-1C210-H03 CARBON RESISTOR 1/6W-1K-J R827
467-1C210-H03 CARBON RESISTOR 1/6W-1K-J R492
467-1C210-H03 CARBON RESISTOR 1/6W-1K-J R351
467-1C212-H03 CARBON RESISTOR 1/6W-1.2K-J R305
467-1C212-H03 CARBON RESISTOR 1/6W-1.2K-J R560
467-1C215-H03 CARBON RESISTOR 1/6W-1.5K-J R732
467-1C222-H03 CARBON RESISTOR 1/6W-2.2K-J R371
467-1C222-H03 CARBON RESISTOR 1/6W-2.2K-J R451
467-1C224-H03 CARBON RESISTOR 1/6W-2.4K-J R515
467-1C227-H03 CARBON RESISTOR 1/6W-2.7K-J R540
467-1C233-H03 CARBON RESISTOR 1/6W-3.3K-J R463
467-1C233-H03 CARBON RESISTOR 1/6W-3.3K-J R702
467-1C233-H03 CARBON RESISTOR 1/6W-3.3K-J R721
467-1C233-H03 CARBON RESISTOR 1/6W-3.3K-J R722
467-1C233-H03 CARBON RESISTOR 1/6W-3.3K-J R728
467-1C233-H03 CARBON RESISTOR 1/6W-3.3K-J R735
467-1C233-H03 CARBON RESISTOR 1/6W-3.3K-J R741
467-1C233-H03 CARBON RESISTOR 1/6W-3.3K-J R742
467-1C239-H03 CARBON RESISTOR 1/6W-3.9K-J R455
467-1C239-H03 CARBON RESISTOR 1/6W-3.9K-J R462
467-1C239-H03 CARBON RESISTOR 1/6W-3.9K-J R321
467-1C247-H03 CARBON RESISTOR 1/6W-4.7K-J R131
467-1C247-H03 CARBON RESISTOR 1/6W-4.7K-J R133
467-1C247-H03 CARBON RESISTOR 1/6W-4.7K-J R154
467-1C247-H03 CARBON RESISTOR 1/6W-4.7K-J R158
467-1C247-H03 CARBON RESISTOR 1/6W-4.7K-J R306
467-1C247-H03 CARBON RESISTOR 1/6W-4.7K-J R733
467-1C247-H03 CARBON RESISTOR 1/6W-4.7K-J R491
467-1C256-H03 CARBON RESISTOR 1/6W-5.6K-J R370
467-1C256-H03 CARBON RESISTOR 1/6W-5.6K-J R583
467-1C262-H03 CARBON RESISTOR 1/6W-6.2K-J W555
467-1C282-H03 CARBON RESISTOR 1/6W-8.2K-J R153A
467-1C282-H03 CARBON RESISTOR 1/6W-8.2K-J R157A
467-1C282-H03 CARBON RESISTOR 1/6W-8.2K-J R562
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R126
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R127
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R163
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R434
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R482A
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R543
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R548
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R816A
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R818A
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R825A
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R827A
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R851A
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R852A
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R912
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R922
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R932
467-1C310-H03 CARBON RESISTOR 1/6W-10K-J R709
467-1C315-H03 CARBON RESISTOR 1/6W-15K-J R331
467-1C318-H03 CARBON RESISTOR 1/6W-18K-J R804
467-1C322-H03 CARBON RESISTOR 1/6W-22K-J R162
467-1C322-H03 CARBON RESISTOR 1/6W-22K-J R384
467-1C327-H03 CARBON RESISTOR 1/6W-27K-J R484
467-1C327-H03 CARBON RESISTOR 1/6W-27K-J R487
467-1C333-H03 CARBON RESISTOR 1/6W-33K-J R171
467-1C333-H03 CARBON RESISTOR 1/6W-33K-J R175
467-1C333-H03 CARBON RESISTOR 1/6W-33K-J R317
467-1C333-H03 CARBON RESISTOR 1/6W-33K-J R385
467-1C347-H03 CARBON RESISTOR 1/6W-47K-J R172
467-1C347-H03 CARBON RESISTOR 1/6W-47K-J R732A
467-1C347-H03 CARBON RESISTOR 1/6W-47K-J R745
467-1C347-H03 CARBON RESISTOR 1/6W-47K-J R807
467-1C368-H03 CARBON RESISTOR 1/6W-68K-J R173
467-1C410-H03 CARBON RESISTOR 1/6W-100K-J R483
467-1C410-H03 CARBON RESISTOR 1/6W-100K-J R802A
467-1C410-H03 CARBON RESISTOR 1/6W-100K-J R803A
467-1C410-H03 CARBON RESISTOR 1/6W-100K-J R582
467-1C415-H03 CARBON RESISTOR 1/6W-150K-J R318
467-1C427-H03 CARBON RESISTOR 1/6W-270K-J R174
467-1C456-H03 CARBON RESISTOR 1/6W-560K-J R465
467-1DA27-H03 CARBON RESISTOR RT14-1/4W-2.7Ω-J R468
467-1DA82-H03 CARBON RESISTOR RT14-1/4W-8.2Ω-J R513
467-1D001-H03 CARBON RESISTOR RT14-1/4W-1Ω-J R404
467-1D010-H03 CARBON RESISTOR RT14-1/4W-10Ω-J R871
467-1D027-H03 CARBON RESISTOR RT14-1/4W-27Ω-J R561
467-1D110-H03 CARBON RESISTOR RT14-1/4W-100Ω-J R486
467-1D222-H03 CARBON RESISTOR RT14-1/4W-2.2K-J R161
467-1D227-H03 CARBON RESISTOR RT14-1/4W-2.7K-J R512
467-1D310-H03 CARBON RESISTOR RT14-1/4W-10K-J R485
467-1D351-H03 CARBON RESISTOR RT14-1/4M-51K-J R539A
467-1D356-H03 CARBON RESISTOR RT14-1/4W-56K-J R539
467-1D433-H03 CARBON RESISTOR RT14-1/4W-330K-J R942
467-2C322-G03 METAL RESISTOR 1/6W-22K-G R482
471-2A56K-003 PEAKING COIL SPT0305-5R6K-5 L351
471-2010K-003 PEAKING COIL SPT0305-100K-5 L331
471-2010K-003 PEAKING COIL SPT0305-100K-5 L361
471-2010K-003 PEAKING COIL SPT0305-100K-5 L751
471-2010K-003 PEAKING COIL SPT0305-100K-5 L752
471-2010K-003 PEAKING COIL SPT0305-100K-5 L753
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M1
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M2
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M3
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M4
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M5
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M6
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M7
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M8
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M9
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M10
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M11
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M12
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M13
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M14
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M15
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M16
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M17
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M18
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M19
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M22
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M28
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M5A
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M23
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M24
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M25
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M26
895-6025030-50 RIVET GB876-86-2.5X3 COPPER D3
895-6025030-50 RIVET GB876-86-2.5X3 COPPER D4
998 JUMPER WIRE W021
998 JUMPER WIRE W022
998 JUMPER WIRE W023
998 JUMPER WIRE W101
998 JUMPER WIRE W102
998 JUMPER WIRE W155
998 JUMPER WIRE W156
998 JUMPER WIRE W161
998 JUMPER WIRE W162
998 JUMPER WIRE W163
998 JUMPER WIRE W164
998 JUMPER WIRE W167
998 JUMPER WIRE W168
998 JUMPER WIRE W169
998 JUMPER WIRE W231
998 JUMPER WIRE W241
998 JUMPER WIRE W242
998 JUMPER WIRE W243
998 JUMPER WIRE W251
998 JUMPER WIRE W252
998 JUMPER WIRE W253
998 JUMPER WIRE W254
998 JUMPER WIRE W265
998 JUMPER WIRE W266
998 JUMPER WIRE W271
998 JUMPER WIRE W312
998 JUMPER WIRE W313
998 JUMPER WIRE W331
998 JUMPER WIRE W341
998 JUMPER WIRE W342
998 JUMPER WIRE W343
998 JUMPER WIRE W344
998 JUMPER WIRE W352
998 JUMPER WIRE W353
998 JUMPER WIRE W354
998 JUMPER WIRE W356
998 JUMPER WIRE W357
998 JUMPER WIRE W358
998 JUMPER WIRE W362
998 JUMPER WIRE W363
998 JUMPER WIRE W371
998 JUMPER WIRE W372
998 JUMPER WIRE W384
998 JUMPER WIRE W391
998 JUMPER WIRE W411
998 JUMPER WIRE W421
998 JUMPER WIRE W422
998 JUMPER WIRE W431
998 JUMPER WIRE W451
998 JUMPER WIRE W452
998 JUMPER WIRE W453
998 JUMPER WIRE W455
998 JUMPER WIRE W461
998 JUMPER WIRE W462
998 JUMPER WIRE W472
998 JUMPER WIRE W473
998 JUMPER WIRE W475
998 JUMPER WIRE W476
998 JUMPER WIRE W482
998 JUMPER WIRE W491
998 JUMPER WIRE W541
998 JUMPER WIRE W542
998 JUMPER WIRE W551
998 JUMPER WIRE W552
998 JUMPER WIRE W554
998 JUMPER WIRE W561
998 JUMPER WIRE W562
998 JUMPER WIRE W563
998 JUMPER WIRE W571
998 JUMPER WIRE W581
998 JUMPER WIRE W591
998 JUMPER WIRE W621
998 JUMPER WIRE W622
998 JUMPER WIRE W642
998 JUMPER WIRE W643
998 JUMPER WIRE W652
998 JUMPER WIRE W653
998 JUMPER WIRE W654
998 JUMPER WIRE W661
998 JUMPER WIRE W662
998 JUMPER WIRE W663
998 JUMPER WIRE W664
998 JUMPER WIRE W751
998 JUMPER WIRE W752
998 JUMPER WIRE W753
998 JUMPER WIRE W754
998 JUMPER WIRE W772
998 JUMPER WIRE W773
998 JUMPER WIRE W774
998 JUMPER WIRE W775
998 JUMPER WIRE W777
998 JUMPER WIRE W781
998 JUMPER WIRE W783
998 JUMPER WIRE W784
998 JUMPER WIRE W785
998 JUMPER WIRE W786
998 JUMPER WIRE W787
998 JUMPER WIRE W791
998 JUMPER WIRE W862
998 JUMPER WIRE W871
998 JUMPER WIRE W872
998 JUMPER WIRE W873
998 JUMPER WIRE W874
998 JUMPER WIRE W875
998 JUMPER WIRE W876
998 JUMPER WIRE W877
998 JUMPER WIRE W878
998 JUMPER WIRE W879
998 JUMPER WIRE W881
998 JUMPER WIRE W981
998 JUMPER WIRE R729
998 JUMPER WIRE R737A
998 JUMPER WIRE R312
998 JUMPER WIRE W355
998 JUMPER WIRE W454
998 JUMPER WIRE R520
998 JUMPER WIRE R581
998 JUMPER WIRE R551
895-6016030-50 RIVET GB876-86 1.6X3 COPPER M29
998 JUMPER WIRE W262
998 JUMPER WIRE W267
667-TK2050-05 KEY BOARD ASS'Y
340-10039-20 LED HFR205 (RED )
VD601
352-38060-60 IC HRM138BB3006 (M) U601
360-10001-00 TACT SWITCH KFC-A06-4X4.5X5B S901
360-10001-00 TACT SWITCH KFC-A06-4X4.5X5B S902
360-10001-00 TACT SWITCH KFC-A06-4X4.5X5B S903
360-10001-00 TACT SWITCH KFC-A06-4X4.5X5B S904
360-10001-00 TACT SWITCH KFC-A06-4X4.5X5B S905
360-10001-00 TACT SWITCH KFC-A06-4X4.5X5B S906
459-2310R-00 CERAMIC CAPACITOR CT1-08-2F4-63V-103Z C602
464-6D647-M0 ELECTROLYTIC CAPACITOR CD110-16V-47uF-M C601
467-1C033-H0 CARBON RESISTOR 1/6W-33Ω-J R602
467-1C133-H0 CARBON RESISTOR 1/6W-330Ω-J R601
467-1C215-H0 CARBON RESISTOR 1/6W-1.5K-J R901
467-1C218-H0 CARBON RESISTOR 1/6W-1.8K-J R902
467-1C230-H0 CARBON RESISTOR 1/6W-3K-J R903
467-1C230-H0 CARBON RESISTOR 1/6W-3K-J R904
467-1C262-H0 CARBON RESISTOR 1/6W-6.2K-J R905
467-1C318-H0 CARBON RESISTOR 1/6W-18K-J R906
655-21201-57 (2-PINS) LEAD WITH HOUSING X901
655-41201-169 (4-PINS) LEAD WITH HOUSING X601
782-M2550-0500 BUTTON PCB
877-50411-00 KEY
877-50412-01 KEY CAP ( PLATE )
998 JUMPER WIRE
667-TK2150-29A SIDE AV BOARD ASS'Y
364-93202-00 AV JACK AV306-2
655-6E301-04 (6-PINS) LEAD WITH HOUSING #XA03
782-M2150-290B SIDE AV PCB
808-6B786-07 AV BAFFLE (SILK-SCREEN )
851-53010-31 SCREW SJ2825 ST3X10FT-D.Zn
868-10043-00 WASHER (14X4X1 METAL)
870-20843-40 SIDE AV BRACKET ( MOLD GREY )
998 JUMPER WIRE
998 JUMPER WIRE LA02
J901
XA01
LA01
EXPLODED VIEW
TK2050
PART LIST OF EXPLODED VIEW
NO. DESCRIPTION PART#
1 PORT BAFFLE 808-6B758-04
2 REAR CABINET 780-10915-J40A
3 SCREW 851-24020-14
4 POWER LINE CLASP 742-30029-00
5 MAIN BOARD ASSY 667-TKP50-01A
6 CRT 335-21225-00U
7 CRT FIXED BLOCK 868-20472-00D
8 CRT SUPPORT 868-20491-00
9 SCREW 851-53010-11
10 RIGHT LEAD TRACK 870-20846-00
11 SPEAKER BRACKET 870-20849-00
12 SIDE AV BRACKET 870-20843-40
13 WASHER 868-20217-00
14 SPEAKER 384-40308-40
15 FRONT CABINET 611-C50X0J0HC
16 BUTTON 877-50411-00
17 SCREW 855-A0029-00
18 BUTTON PCB 782-13Y90-050A
19 STANDYBY BOARD ASSY 667-TK2050-05
20 SCREW 851-24020-11
21 COMPONENT SCREW 855-96024-31
22
23 CRT BOARD No number
24 SCREW 851-24020-14
25 REAR CABINET 780-10915-J40A
SCHEMATIC DIAGRAM
CAUTION:all the parts in the schematic diagram marked with shodows and the signs of
are extremely
important for safety. In case of replacement of any part of components. Be sure to consult the service manual
carefully.
1. the schematic diagram is characteristic. The various valus in the electric circuits are basic data, which are
changeable according to the various basic circuits.
2. testing waves are abtained by inputing the standard color bar of the signed.
3. resistance unit is in Ohm, namely: K=1000; M=1000K; Capacitance unit is in µF; P=µµF(µ=10
6
)
4. Unless othervise noted inside, all resistors are 1/6W, the withstand voltage of all capacitor are 50V.
5. Inductance unit is in µH.
6. The mark
in the diagram means Ferrite ring
7. The symbols of various types of resistors and capacitors are listed as follows:
Carbon film resistor
Metal film resistor
M
Potentiometer resistor
1/2w resistor
1w resistor
2w resistor
3w resistor
Ceramic capacitor
AC Ceramic capacitor
Terylene capacitor
Polypropylene capacitor
Metal Terylene capacitor
Aluminium electrolyse capacitor
Tantalum electrolyse capacitor
AC
1
2
3
T
36
Loading...