Xoceco LC-19HU5610UAE Schematic

LCD TELEVISION

LC-19HU56S

CONTENTS

Safety precautions………………………………………………………………………..…
Alignment instructions …………………………….…….…………………………………
Method of software upgrading……………………………………………………………..
Working principle analysis of the unit……………………………….………….………….
Block diagram…………………………………..………………………………….…………
IC block diagram………………………………………………………………………..……
Wiring diagram …………………………………………………………………………….
Troubleshooting guide ………………………………………………………………..……
Schematic diagram…………………………………………………………………………
APPENDIX-A: Assembly list
APPENDIX-B: Exploded View

1
3

7

13
14
15
19

20
25

Attention: This service manual is only for service personnel to take reference with. Before

servicing please read the following points carefully.

Safety precautions

1. Instructions

Be sure to switch off the power supply before replacing or welding any components or
inserting/plugging in connection wire. Anti static measures must be taken (throughout the entire
manufacturing process!):
a) Do not touch here and there by hand at will;
b) Be sure to use anti static electric iron;
c) It’s a must for the welder to wear anti static gloves.
Please refer to the detailed list before replacing components that have special safety requirements.
Do not change the specs and type at will.

2. Points for attention in servicing of LCD

2.1 Screens are different from one model to another and therefore not interchangeable. Be sure to
use the screen of the original model for replacement.

2.2 Be sure to take proper measures in protecting yourself and the machine when testing the
system in the course of normal operation or right after the power is switched off. Please do not
touch the circuit or the metal part of the module that is in operation mode. Relevant operation is
possible only one minute after the power is switched off.

2.3 Do not use any adapter that is not identical with the TV set. Otherwise it will cause fire or
damage to the set.

2.4 Never operate the set or do any installation work in bad environment such as wet bathroom,
laundry, kitchen, or nearby fire source, heating equipment and devices or exposure to sunlight etc.
Otherwise bad effect will result.

2.5 If any foreign substance such as water, liquid, metal slices or other matters happens to fall into
the module, be sure to cut the power off immediately and do not move anything on the module lest it
should cause fire or electric shock due to contact with the high voltage or short circuit.

2.6 Should there be smoke, abnormal smell or sound from the module, please shut the power off at
once. Likewise, if the screen is not working after the power is on or in the course of operation, the
power must be cut off immediately and no more operation is allowed under the same condition.

2.7 Do not pull out or plug in the connection wire when the module is in operation or just after the
power is off because in this case relatively high voltage still remains in the capacitor of the driving
circuit. Please wait at least one minute before the pulling out or plugging in the connection wire.

2.8 When operating or installing LCD please don’t subject the LCD components to bending, twisting
or extrusion, collision lest mishap should result.

2.9 As most of the circuitry in LCD TV set is composed of CMOS integrated circuits, it’s necessary
to pay attention to anti statics. Before servicing LCD TV make sure to take anti static measure and
ensure full grounding for all the parts that have to be grounded.

2.10 There are lots of connection wires between parts behind the LCD screen. When servicing or
moving the set please take care not to touch or scratch them. Once they are damaged the screen
would be unable to work and no way to get it repaired.
If the connection wires, connections or components fixed by the thermotropic glue need to
disengage when service, please soak the thermotropic glue into the alcohol and then pull them out

1

in case of damage.

2.11 Special care must be taken in transporting or handling it. Exquisite shock vibration may lead to
breakage of screen glass or damage to driving circuit. Therefore it must be packed in a strong case
before the transportation or handling.

2.12 For the storage make sure to put it in a place where the environment can be controlled so as to
prevent the temperature and humidity from exceeding the limits as specified in the manual. For
prolonged storage, it is necessary to house it in an anti-moisture bag and put them altogether in one
place. The ambient conditions are tabulated as follows:

Temperature Scope for operation 0 ~ +50 oC

Scope for storage -20 ~ +60 oC

Humidity Scope for operation 20% ~ 85%

Scope for storage 10% ~ 90%

2.13 Display of a fixed picture for a long time may result in appearance of picture residue on the
screen, as commonly called “ghost shadow”. The extent of the residual picture varies with the
maker of LCD screen. This phenomenon doesn’t represent failure. This “ghost shadow” may remain
in the picture for a period of time (several minutes). But when operating it please avoid displaying
still picture in high brightness for a long time.

3. Points for attention during installation

3.1 The front panel of LCD screen is of glass. When installing it please make sure to put it in place.

3.2 For service or installation it’s necessary to use specified screw lest it should damage the screen.

3.3 Be sure to take anti dust measures. Any foreign substance that happens to fall down between
the screen and the glass will affect the receiving and viewing effect

3.4 When dismantling or mounting the protective partition plate that is used for anti vibration and
insulation please take care to keep it in intactness so as to avoid hidden trouble.

3.5 Be sure to protect the cabinet from damage or scratch during service, dismantling or mounting.

2

Alignment instructions

1. Test equipment

PM5518 (video signal generator)
VG-848 (VGA, HDMI signal generator)
VG-849 (digital video signal generator)
CA210 (color analyzer)

2. Power test

Connect main board, power board and IR board according to the wiring diagram, connect the power
and press “standby” to turn on the TV.
Measure the pin voltage of XB1, the data is shown in table1:

Table1 voltage data of XB1

XB1 Pin1 Pin2/4/7/8/13 Pin3 Pin5/6 Pin12
LC-19HUXX
LC-22HUXX

4.75 V～5.25 V

4.75 V～5.25 V

3. Alignment flow-chart

The alignment flow-chart is shown as fig-1

Check DDC, FLASH, HDCP and power control IC

Combined test for general assembly

IF channel AFT voltage of TV and AGC voltage adjustment

4. Alignment instruction

4.1 Unit adjustments
Connect all the boards according to wiring diagram, then power on and observe the display.
Method for entering factory menu: press “INPUT”, “2”, “5”, ”8” and “0” in turn to enter factory
menu; press “CH+” and “CH-” to select adjustment items and press “VOL+” and “VOL-” to adjust
value items, press “MENU” repeatedly to exit.
Method for software upgrading: When software upgrading please enter factory menu first, select
ISP from OPTION, set ISP to 1 and you can begin to upgrade. Af ter upgrade finished, it needs to set

GND

GND

4.75 V～5.25 V 11.4 V～12.6 V 28.8 V～35.2 V

4.75 V～5.25 V 11.4 V～12.6 V 28.8 V～35.2 V

Factory initialization setup

White balance adjustment

Performance check

Preset ex-factory

Fig-1 Alignment flow-chart

3

ISP back to 0. If the picture can’t display when upgrading, it needs to solder JB1 on main board.
Please unsolder JB1 again after upgrading.

4.2 Initialization
Enter factory menu, select “OPTION”, “EEPROM” and “HOTEL OPTION” sub-menu, for adjusting
items see table 4.

Table 4 sub-menu adjustment

Items Preset Remarks

HOTEL 0 1: HOTEL OPTION of factory menu is optional

0: HOTEL OPTION of factory menu is not optional

LOGO 1 1: display LOGO in no signal or turn on

0: no LOGO display
ADC PRESCALE 046 Software will preset the data according to different status.
SIF PRESCALE 02E Software will preset the data according to different status.
BACK LIGHT FF Software will preset the data according the type of panel
ALL COLOR 1 1: white balan ce of each channel auto offset based on the HDMI white

balance

0: white balance of each channel adjust the offset base separately

Note: don’t set ALL COLOR to 1after the offset adjustment, if you do so, the

adjusted parameter of each channel will recover to the parameter of HDMI.
EEPROM-MEMORAY
RECALL

> EEPROM Initialization (operate when EEPROM data chaos)

4.3 Adjustment for AFT voltage and AGC voltage of IF channel in TV

4.3.1 IF AFC adjustment
Disconnect J1(B face), input 38.9MHz PAL signal of 80dB to the pole of J1 near L1 1, Adjust L5

to value 1.25V of TP2. Enter factory menu, adjust TDA4470 from BG to LL, input 33.9MHz SECAM
signal of 80dB, adjust R71 to value 1.25V of TP2 then solder J1.

4.3.2 IF AGC adjustment

Input 184.25MHz(PAL/BG) RF signal of 60dBuv to RF terminal, adjust R64 to value 3.75 V±

0.25 V of TP4 and there should be no obvious snowy picture. Increase the signal to 90dBuv and it

should be display normally and no obvious noise.

4.4 White balance adjustment

4.4.1 white balance adjustment of HDMI

a. Input VG-849 signal from HDMI: TIMING854 (800* 600/60Hz) and eighth-level gray scale

signal of PAT920. Use color analyzer CA210 to adjust white balance.

b. Enter submenu of COLOR TEMP, Select 9300k of color temperature

c. Fix value of B OFF, adjust R OFF and G OFF, let the color coordinate of the second level be
(285, 293) and the brightness be about 3nit-6nit. Fix value of B GAIN, adjust R GAIN and G GAIN,
let the color coordinate of the seventh level be (285, 293). Adjust R OFF, G OFF, R GAIN and G
GAIN repeatedly until the value of the two levels gray-scale are (285, 293).

4.4.2 VGA/YPBPR/AV white balance check and correct

a. Connect VG-848 signal of VGA to VGA terminal: TIMING854 ( 800 x 600 / 60Hz)
(PATTERN:CROSS) and auto adjust to full screen, then input PAT948 black/white signal, enter
factory menu ADC ADJ, select AUTOTUNE and wait for OK display. Input PAT920(8 gray levels),
check if the white balance is normal, if not, enter COLOR TEMP menu and set ALL COLOR to 0 and
fine adjust according to the method of 4.4.1c)

4

b. Connect VG-848 signal of YPBPR to YPBPR terminal and input TIMING972(1080i/60HZ)
100% color bar of PAT976(include black/white bars), Enter ADC ADJ submenu, select AUTOTUNE
and wait for OK display. Input PAT920(8 gray levels), check if the white balance is normal, if not, set
ALL COLOR to 0 and fine adjust according to the method of 4.4.1c)

c. Connect AV signal (PM5518, 8 gray levels, NTSC) to VIDEO1 terminal, check if the white
balance is normal, if not, set ALL COLOR to 0 and fine adjust according to the method of 4.4.1c)

Note: it can’t set back to 1 once ALL COLOR changes to 0.

5. Performance check

5.1 TV function
Enter searching menu → auto search, connect RF-TV terminal with central signal source and check
if the picture is normal, if there are channels be skipped. Check TXT and parental control.

5.2 A V, YPbPr terminals
Input AV/S, YPbPr/YCbCr HD signal, check if the picture is normal.

5.3 VGA terminal
Insert VGA terminal, input VGA format signal of 640x480@60 Hz and check if the display is normal.

5.4 Check sound channel
Check the speaker of each channel.

5.5 Other function check
Check the ON/OFF timer, sleep timer, picture/sound mode, OSD, freeze/mute, stereo, etc.

5.6 Presetting before ex-factory

Item Setting Item Setting Item Setting

PICTURE MODE STANDARD BALANCE 50 OSD LANGUAGE English
COLOR MODE NORMAL VOLUME 50 OSD HPOSITION 50
NR WEAK SLEEP TIMER OFF OSD VPOSITION 50
ZOOM FULL TTX LANGUAGE WEST OSD HALFTONE 50
SOUND MODE STANDARD BLUE SCREEN OFF OSD DURATION 15
AVC OFF WSS OFF

6. Software instruction

No.

Code No.

Software instruction

Function

Type

Flash written
before paste

Method

NS14 5270008001 ATMEGA8L Power management IC Yes

NS3 5272540003 EN25F40
NA3(NB3) 5272402002 24C02N-10SI27 HDMI EDID Yes

NB3(NB7)

NS5 5272404002 24C04N-10SI27 HDMI HDCP Yes

NS1 5272432001 AT24LC32A/SN

5272421001

(5272402002)

24LCS21A/SN

(24C02N-10SI27)

Main CPU program

VGA EDID Yes

Store some important
information

Yes

No

5

Written with
instrument like
ALL11

Unnecessary to

write

6.2 Main CPU software burn-in need write-protection, below is the setting:

6.2.1 If use ALL - 100:

a) Enter into AUTO interface, select Config. Make sure Config must be selected
when burn-in Flash.
b) Click Config Setting, set Protect item to All Protect, set SRWD item to Enable,
then click OK, write-protection setting is finished. Every time when exit from ALL-100
burn-in program, if want to enter again, the above two steps’ setting must be done
again.

If SRWD item is not available, please upgrade ALL-100 burn-in program.

6.2.2 If use Mstar on-line burn-in tool

6.2.2.1 Open the tool, click Device.

a) Select WP Pin pull to high during ISP
b) Select New Setting Below.

c) Select Status Register Bit2 Bit3 Bit4 Bit7. Now write-protection setting is

finished.

6.2.2.2 When do on-line upgrade, firstly make sure to confirm write-protection is set
correctly.

6

Method of software upgrading

1. The tools and software demanded

1) Please confirm that PC has the software of ISP_TOOL and install the parallel interface drive
program Port95nt.

2) ISP_TOOL icon is bellow:

3) One parallel cable (25 pins) and one VGA cable (15 pins), t he p arallel cable connect s the PC and
the upgrade instrument, the VGA cable connects the TV and the upgrade instrument.

2. The steps for upgrading software

1) Please confirm that the connection wires and the upgrade instrument are connected well before
the software written and then power on the TV.

2) Double click the icon ISP_TOOL to open it:

3) Press “Connect“ to connect TV, if the connection is done successfully as shown below, then
press “enter”.

7

Note: if it appears error, check the connection wires and check if ISP item of the factory menu is set
to 1, if not, please set it to 1.

4) After connection is done, it needs to read the Binary document. Press “Read” as shown below:

5) Search the document needed to write in the “Read” check box.

8

Select

6) Select the document then the window will appear as shown below:

9

7) Press “Auto” to select the writing function.

Select the items shown in the picture above:
(a) Read File

10

(b) Program
(c) Exit ISP
(d) Erase Device
(e) File Area

8) Press “Run” to begin the writing program, wait till the blue bar is complete.

After writing, it will display OK:

If there is error appeared (shown as below), press “Run” again to rewrite the program till it is
success.

11

Note1: keep the connection well and don’t cut off the power during the writing process.
Note2: the writing speed can be adjusted as shown below. Select “Config” then adjust Speed BAR,
the value is bigger the speed is faster . But it is e asier to appear error when increase the speed, so it
need to select a suitable speed according the PC.

Step 1

Step 2

12

Working principle analysis of the unit

The RF signal received by antenna will be sent to tuner TUN1, then IF signal will be obtained
through high amplifier and mixed frequency, through pre-intermediate amplified by V15, then it will
be sent to SAW filter Z17 to do IF filter and get better IF characteristics, then it will be sent to N3
(TDA4470) to do intermediate amplification, phase-locked loop VCO and synchronous wave
detection to get video signal TV-V; after pre-intermediate amplification IF will also be sent to SAW
filter Z16 to do filter at the same time, then it will be sent to TDA4470 to do intermediate
amplification and output the second sound intermediate frequency signal (TV-SIF).

The TV-V signal output from TDA4470 together with TV-SIF will be sent to main chip
NS2(MST9E19B).

Video signals of AV, VGA and HDMI will be sent to MST9E19B, too.

Video signal of YPbPr and Video RGB of SCART1 via video switch N5 ( PI5V330) will be sent to
MST9E19B.

Video signal V (CVBS) of SCART1, YPbPr L/R and SCART1 L/R will be sent to MST9E19B.

The main chip NS2(MST9E19B) is a high performance and fully integrated IC, which can
realize video demodulating, video switch selection, A/D and D/A conversion, interlace/progressive
processing, modes conversion, OSD and low-voltage differential output, etc. And it also has
functions of audio selection, processing and MCU.

The video signal via MST9E19B processing, sends out 4 pairs of dif ferential signal and 1 p air of
clock signal for LCD panel display. TV-V output fromTDA4470 via double video amplifying, it will be
sent to SCART1 for AV-OUT.

Audio signal via MST9E19B processing will be sent to sound amplifier NV12 (TDA7266SA)
amplifying to speaker. TV-SIF via MST9E19B demodulating and sound processing then output to
NV11(LM358D) amplifying, the signal will be sent to SCART1 as AV-OUT.

133

Block diagram (LC-19HU56S)

HDMI
VGA
AV
YPbPr

SCART1-RGB

SCART1-V
SCART1-L/R
L/R-AV
L/R-VGA
L/R-YPbPr
L/R
TUNER

EDID
24C02

PRE AMP

TV-SIF

TV-V

SCART1-V OUT
TV-L/R SCART1-L/R OUT

IF AMP
TDA4470

HDTV SW.
PI5V330

SAW

KEY
24C02

EDID
24C02

2*AMP

LCD TV
CONTROLLER

MST9E19B

FLASH

EEPROM

PANEL

AUDIO AMP .
TDA7266SA

SPEAKER

PRE AMP
LM358D

14

IC block diagram

1. MST9E19A

The MST9E19A is a h igh performance and fully integrated IC for multi-function LDC monitor/TV with
resolutions up to SXGA (1280X1024)/WXGA+(1440X900). It is configured with an integrated
triple-ADC/PLL, an integrated DVI/HDCP/HDMI receiver, a multi-standard TV video and audio
decoder, a video de-interlacer, a scaling engine, the MStarACE-3 color engine, an on-screen
display controller , an 8-bit MCU, and a built-in output panel int erface. To further reduce system costs,
the MST9E19A also integrates intelligent power management control capability for green-mode
requirements and spread-spectrum support for EMI management.

15

2. TDA7266SA

The TDA7266SA is a dual bridge amplifier.

16

3. TDA4470

The TDA4470 is an integrated bipolar circuit for multi-standard video/sound IF(VIF/SIF) signal
processing in TV/VCR and multimedia applications. The circuit processed all TV video IF signals
with negative modulation (e.g., B/G standard), positive modulation (e.g., L standard) and the AM,
FM/NICAM sound IF signals.

17

18

Wiring Diagram

Board

Back light

Power Board

Speaker

IR Board,
Key Board

30-pin

13-pin

Main Board

7-pin

4-pin

Pin

Insert

Tuner Board

Pin

19

Trouble shooting

1. Fault clearance

Before servicing please check to find the possible causes of the troubles according to the table

below.

1.1 Antenna (signal):

Picture is out of focus or jumping  Bad status in signal receiving

 Poor signal
 Check if there are failures with the electrical connector or

the antenna.

 Check if the antenna is properly connected.

Fringe in picture  Check if the antenna is correctly oriented.

 Maybe there is electric wave reflected from hilltop or

building.
Picture is interfered by stripe shaped
bright spots

There appear streaks or light color
on the screen

1.2 TV set:

Symptoms Possible cause
Unable to switch the power on  Check to see if the power plug has been inserted properly

No picture and sound  Check to see if the power supply of liquid crystal TV has

Deterioration of color phase or color
tone
Screen position or size is not proper  Check is the screen position and size is correctly set up.
Picture is twisted and deformed  Check to see if the picture-frame ratio is properly set up.
Picture color changed or colorless  Check the “Component” or “RGB” settings of the liquid

 Possibly due to interference from automobile, train, high

voltage transmission line, neon lamp etc.

 Maybe there is interference between antenna and power

supply line. Please try to separate them in a longer

distance.

 Maybe the shielded-layer of signal wire is not connected

properly to the connector.

 Check if interfered by other equipment and if interfered

possibly by the equipment like transmitting antenna,

non-professional radio station and cellular phone.

into the socket.

been switched on. (As can be indicated by the red LED at
the front of the TV set)

 See if it’s receiving the signal that is transmitted from other

source than the station

 Check if it’s connected to the wrong terminal or if the input

mode is correct.

 Check if the signal cable connection between video

frequency source and the liquid crystal TV set is correct.

 Check if all the picture setups have been corrected.

crystal TV set and make proper adjustment according to the

20

signal types.
Picture too bright and there is
distortion in the brightest area

 Check if the contrast setting is too high.
 Possibly the output quality of DVD broadcaster is set too

high.

 It maybe also due to improper terminal connection of the

video frequency signal in a certain position of the system.
Picture is whitish or too bright in the
darkest area of the picture

 Check if the setting for the brightness is too high
 Possibly the brightness grade of DVD player (broadcaster)

is set too high.
No picture or signal produced from
the displayer if “XXX in search”
appears.
There appears an indication ­“outside the receivable scope)

 Check if the cable is disconnected.
 Check if it’s connected to the proper terminal or if the input

mode is correct.

 Check if the TV set can receive input signal. The signal is

not correctly identified and VGA format is beyond the

specified scope.
Remote control cannot work
properly

 Check if the batteries are installed in the reverse order.
 Check if the battery is effective.
 Check the distance or angle from the monitor.
 Check if there is any obstruct between the remote control

and the TV set.

 Check if the remote control signal- receiving window is

exposed to strong fluorescence.
No picture and sound, but only

hash.

 Check if the antenna cable is correctly connected, or if it

has received the video signal correctly.
Blur picture  Check if the antenna cable is correctly connected.

 Of if it has received the right video signal.

No sound  Check if the “mute” audio frequency setting is selected.

 Check if the sound volume is set to minimum.
 Make sure the earphone is not connected.
 Check if the cable connection is loose.

When playing VHS picture search
tape, there are lines at the top or
bottom of the picture.

 When being played or in pause VHS picture search tape

sometimes can’t provide stable picture, which may lead to

incorrect display of the liquid crystal TV, In this case please

press “auto” key on the remote control so as to enable the

liquid crystal TV set to recheck the signal and then to

display correct picture signal

21

2. Troubleshooting guide

k

f

p

d

2.1. No raster

Turn-on power supply, chec
if the red indicator is light in
the STANDBY?

no

Check if PIN 3(5V) of XS11
on main board is normal?

no

Check STANDBY circuit o

ower supply board

Check NS2 and its

peripheral circuit

no

yes

Press POWER button on the
unit or remote control an
check the indicator.

blue

Check if the PIN 9, 10 of XS11 on main
board is high-level?

yes

Check back light board

no

Check N801 and its

peripheral circuit

red

Check if the PIN 11 of XS11
on main board is low-level?

yes

Check power
supply board

22

2.2. Raster appears, but no picture

f p

d

P

t

f

d

p

u

d

P

Check if the unit button
and remote control are
active?

yes

Check if the OSD men
can be displaye
normally after pressing
MENU.

no

no

Replace
main board

no

Enter factory-menu,
initialize EEPROM,
then turn off the TV,
turn on again, check i

icture appears?

Adjust main boar

again

yes

Check TUN1 an
its periphery

yes

yes

yes

Check if TP1 on the

Check if TP1 on the
TV board has 1VP

TV board has 1VP
signal or noise?

signal or noise?

no

Check if all channels
have no signal?

Which channel has

no signal ?

TV

Check if outpu
IF signal o
TUN1 (pin 11) is
normal?

Check N3 and its

eriphery

no

VGA/YPBPR/SCART/HDMI

Replace
main board

no

yes

23

2.3. No sound (Use TV input as an example)

f

N

p

d

p

p

Check if PIN 3, 13
voltage of NV12 is
normal?

yes

Check the waveform

of PIN 4, 12 o

V12

no

Check power supply

Check N3 PIN 24

waveform.

Check TUN1 PIN 11

waveform.

Check TUN1 and its

eriphery

no

no

no

yes

yes

yes

Check NV12 an
its periphery

Check NS2 and its

eriphery

Check N3 and its

eriphery

24

Main Board Schematic diagrams

25

Page 1, total 8 pages

Main Board Schematic diagrams

26

Page 2, total 8 pages

Main Board Schematic diagrams

27

Page 3, total 8 pages

Main Board Schematic diagrams

28

Page 4, total 8 pages

Tuner Board Schematic diagrams

29

Page 5, total 8 pages

30

IR & Key Board Schematic diagrams

Page 6, total 8 pages

31

Power Board Schematic diagrams

Page 7, total 8 pages

32

Back light Board Schematic diagrams

Page 8, total 8 pages

Appendix-A: Board list (9219HU5610)

Name No. Main components & its number

Tuner Board 6HU0885510 N3 TDA4470 （5274470001）

Main Board 6HU0880110 NS2 MST9E19B （5270919002）

NV12 TDA7266SA （5277266001）

Key Board 6HU08805A0

IR Board 6HC0060910

Back Light Board 6LV0261410

Power Board 6HU0822010

Remote Control 6010N03401 RC-N34-0A

Display Panel 5203195201 CLAA185WA02

33

APPENDIX-B: Exploded view (LC-19X56)

34

PART LIST OF EXPLODED VIEW

NO. DESCRIPTION

1 panel
2 front cabinet
3 speaker
4 light conducting column
5 IR decorative piece
6 IR light conducting piece
7 IR board
8 main board

9 interface baffle
10 wall mounting bracket
11 screw
12 back cabinet
13 stand
14 screw
15 power switch bracket
16 conductive interleaver
17 key board
18 backlight board
19 power board
20 main board frame
21 EVA adhesive tape

Note: design and specifications are subject to change without notice.

35

9219HU5610
Ver.1.0