Xmark TGL User Manual

User Manual - INTRODUCTION
TAG LINK
The eXI Tag Link device automates tag administration by providing a localized eLink between the Halo or Assetrac application software and the targeted tag device.
The Tag Link communicates directly with the system computer through a serial port and may be powered by an internal 9 volt battery or accessory AC wall adapter. The Tag Link enables the software application to transparently interact with the tags.
Tag Link Views
PHOTO ILLUS: TAG LINK WITH PTAG
WITH LED HIGHLIGHTED
PHOTO ILLUS: TAG LINK WITH MOTHER TAG
Copyright 2003 - eXI Wireless Systems Inc. Page XX 980-000003 – 002. R1.01
User Manual - INTRODUCTION
Tag Link Range
The communication range for Tag Link is designed to be typically less than 12 inches. Therefore, it is recommended that the tags be located within 6 to 12 inches of Tag Link. Those tags with ‘off body’ sensor must be placed on the front panel in the marked area. This will assure that the alarm TIC message is not transmitted.
Tag Link Functions
The following table lists the functions that are performed transparently in response to commands from the application software:
COMMAND TAG LINK ACTION LED
Power Up Powers up from sleep mode
Power Down Return to sleep mode immediately or after 30
seconds if no application command
Check RF Noise Measures and reports interference at 307 kHz
Measures and reports interference at 433.92 MHz
Test Tag TIF Interrogates tag and returns ID and tag status
Test Tag TIC Tag Link waits for TIC signal from specified tag
Set TLM Tag Link issues eLink TLM set command
Disable TLM Tag Link issues eLink TLM disable command
Check TLM Tag Link queries tag and reports rate to application
Assign MTAG Reads Mother Tag ID and assigns dynamic ID
MTAG Bond Sends baby tag ID(s) to Mother Tag, Mother Tag is
then bonded to the assigned tag(s)
none
none
Green Flashes
Red Flashes
See next table
See next table
See next table
See next table
See next table
See next table
See next table
Each operation is performed for a maximum of 10 seconds. During application the following audio-visual signals are output:
ACTION BEEPER LED’s
Command received Very short beep None
Command succeeded Longer beep random
Command failed 4 short beeps
Copyright 2003 - eXI Wireless Systems Inc. Page XX 980-000003 – 002. R1.01
Both briefly on
User Manual - SUPERVISOR
Restricted Rights
eXI's commercial software and commercial computer software documentation is provided to United States Government agencies in accordance with the terms of this Agreement, and per subparagraph "(c)" of the "Commercial Computer Software - Restricted Rights" clause at FAR 52.227-19 (June 1987). For DOD agencies, the restrictions set forth in the "Technical Data-Commercial Items" clause at DFARS 252.227-7015 (Nov 1995) shall also apply.
FCC Regulations
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
eXI Wireless Systems Model No.: Tag Link
CANADA: 287710217261A
* This device complies with Part 15 of the FCC Rules. Operation is subject to the following two rules: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
FCC ID: HE7TGL
Made in Canada
Copyright 2003 - eXI Wireless Systems Inc. Page 137 980-000003 – 002. R1.01
Loading...