XLPower Specter700 User Manual
IMPORTANT NOTES:
SAFETY GUIDELINES:
*THIS RADIO CONTROLLED HELICOPTER IS NOT A TOY.
*THIS RADIO CONTROLLED HELICOPTER CAN BE VERY DANGEROUS.
*THIS RADIO CONTROLLED HELICOPTER IS A TECHNICALLY COMPLEX DEVICE WHICH HAS
TO BE BUILT AND HANDLED VERY CAREFULLY.
*THIS RADIO CONTROLLED HELICOPTER MUST BE BUILT FOLLOWING THESE INSTRUCTIONS.
THIS MANUAL PROVIDES THE NECESSARY INFORMATION TO CORRECTLY ASSEMBLE THE
MODEL. IT IS NECESSARY TO CAREFULLY FOLLOW ALL THE INSTRUCTIONS.
*INEXPERIENCED PILOTS MUST BE MONITORED BY EXPERT PILOTS.
*A RADIO CONTROLLED HELICOPTER MUST ONLY BE USED IN OPEN SPACES WITHOUT
OBSTACLES, AND FAR ENOUGH FROM PEOPLE TO MINIMIZE THE POSSIBILITY OF
ACCIDENTS OR OF INJURY TO PROPERTY OR PERSONS.
*A RADIO CONTROLLED HELICOPTER CAN BEHAVE IN AN UNEXPECTED MANNER,
CAUSING LOSS OF THE MODEL, MAKING IT VERY DANGEROUS.
*LACK OF CARE WITH ASSEMBLY OR MAINTENANCE CAN RESULT IN AN UNRELIABLE AND
DANGEROUS MODEL.
*FLY ONLY IN AREAS DEDICATED TO THE USE OF MODEL HELICOPTERS.
*FOLLOW ALL CONTROL PROCEDURES FOR THE RADIO FREQUENCY SYSTEM.
*IT IS NECESSARY THAT YOU KNOW YOUR RADIO SYSTEM WELL. CHECK ALL FUNCTIONS OF
THE TRANSMITTER BEFORE EVERY FLIGHT.
*THE BLADES OF THE MODEL ROTATE AT A VERY HIGH SPEED; BE AWARE OF THE
DAMAGE THEY MAY CAUSE.
*NEVER FLY IN THE VICINITY OF OTHER PEOPLE.
NEITHER XLPOWER NOR ITS AGENTS HAVE ANY CONTROL OVER THE
ASSEMBLY, MAINTENANCE AND USE OF THIS PRODUCT.
THEREFORE, NO RESPONSIBILITY CAN BE TRACED BACK TO THE
MANUFACTURER. YOU HEREBY AGREE TO RELEASE XLPOWER FROM ANY
RESPONSIBILITY OR LIABILITY ARISING FROM THE USE OF THIS PRODUCT.
LENGTH: 1300MM
WIDTH: 134MM
HEIGHT: 376MM
MAIN ROTOR BLADES: 685-716MM
TAIL ROTOR BLADES: 105-115MM
MOTOR PINION: 11T INCLUDED;10,12 OPTIONAL
MAIN GEAR: 106T
TAIL PINION: 17T
AUTOROTATION GEAR: 80T
MAIN TO TAIL GEAR RATIO: 4.7
RTF WEIGHT: 4900G-5300G
MAIN SHAFT DIAMETER: 15MM
FEATHERING SHAFT DIAMETER: 10MM
TAIL BOOM DIAMETER: 27MM
BATTERY TRAY SIZE: L:350MM W:66MM H:70MM (12s-14s)
1
HB-1
SPECIFICATION:
HB-1
BAGS:
HB-1 HB-1-1 HB-1-2 HB-1-4 HB-1-5 HB-1-6
WASHER
10x16x1
BEARING
10x19x7
BEARING
10x19x7
SCREW
M3x10
LINKAGE BALL
5x10.6
THRUST BEARING
10x18x5.5
INSIDE
OUTSIDE
THRUST BEARING
APPLY GREASE
B
I
G
G
E
R
D
I
A
M
E
T
E
R
S
M
A
L
L
E
R
D
I
A
M
E
T
E
R
CUSTOMISABLE
INNER HOLE:AGILE
OUTER HOLE:STABLE
PITCH ARM
2
APPLY A LITTLE AMOUNT OF
243 THREADLOCK WHEN
FIXING A METAL PART
HB-1
BAGS:
HB-1 HB-1-1 HB-1-2 HB-1-4 HB-1-5 HB-1-6
WASHER
10x16x1
THE BLADE GRIPS MUST MOVE FREELY
BUT THEY SHOULD NOT MOVE JUST
FROM THEIR OWN WEIGHT
ADD MORE 0.1MM SHIMS
IF PRELOAD CHANGED
HB-1-6
PUT THE O-RINGS
OUTSIDE
INSIDE
ONTO THE DAMPER
3
APPLY A LITTLE AMOUNT OF
243 THREADLOCK WHEN
FIXING A METAL PART
WASHER
6x16x2
SCREW
M6x12
HEAD DAMPER
HB-1
LINKAGE BALL
5x10.6
LINKAGE BALL
5x26.6
LINKAGE BALL
5x10.6
HB-1
BAGS:
HB-1 HB-1-1 HB-1-2 HB-1-4 HB-1-5 HB-1-6
4
SCREW
M2x4
APPLY A LITTLE AMOUNT OF
243 THREADLOCK WHEN
FIXING A METAL PART
HB-1
LINKAGE BALL
5x10.6
HB-1
BAGS:
HB-1 HB-2
5
SCREW
M4x20
SCREW
M3x25
PIN
BEARING
3x7x3
MAIN
SHAFT
WASHER
3x5x0.5
APPLY A LITTLE AMOUNT OF
243 THREADLOCK WHEN
FIXING A METAL PART
BEARING
3x7x3
LINKAGE BALL
5x10.6
BAGS:
BB-1
6
NOTE
DIRECTION
APPLY A LITTLE AMOUNT OF
243 THREADLOCK WHEN
FIXING A METAL PART
SCREW
M2.5x5
HB-1
HB-1
BAGS:
BB-1 BB-2 BB-1-1
6
APPLY A LITTLE AMOUNT OF
243 THREADLOCK WHEN
FIXING A METAL PART
RIGHT SIDE
OF THE FRAME
BEARING
3x7x3
LINKAGE BALL
5x10.6
BAGS:
BB-1
6
NOTE
DIRECTION
APPLY A LITTLE AMOUNT OF
243 THREADLOCK WHEN
FIXING A METAL PART
HB-1
BAGS:
BB-1
7
APPLY A LITTLE AMOUNT OF
243 THREADLOCK WHEN
FIXING A METAL PART
SERVO
MOUNT
SCREW
M2.5x10
SCREW
M2.5x5
SERVO SHAFT
FACING DOWN
LEFT SIDE
OF THE FRAME
BEARING
15x24x7
HB-1
HB-1
BAGS:
BB-1 BB-2 BB-1-3 BB-1-4 BB-1-5 BB-1-6 BB-1-7 BB-1-8 BB-1-9
8
APPLY A LITTLE AMOUNT OF
243 THREADLOCK WHEN
FIXING A METAL PART
FLAT CAP SCREW
M3x6
HB-1
HB-1
BAGS:
BB-1 BB-2 BB-1-3 BB-1-4 BB-1-5 BB-1-6 BB-1-7 BB-1-8 BB-1-9
8
APPLY A LITTLE AMOUNT OF
243 THREADLOCK WHEN
FIXING A METAL PART
FLAT CAP SCREW
M3x6
Loading...