xit404 TOKINA FISHEYE10-17mm 3.5-4.5:2.8 (CANON) MANTA FOCUS RING Assembly Instructions

Revsion 2.0 - APR2013

www.xit404.com

Thank you for purchasing Xit 404’s Tokina 10-17mm Focus Ring to use
with our Manta Gears. On the back is our warranty information to help you
prolong the life of this product.

This product is in our Manta Line. The advantage of the Manta Line of
Rings and Gears is that the parts are interchangeable. For example the
Manta Gear fits on all Manta Focus/Zoom Rings as well as our
Manta Teleconverter Extension Rings. This allows you to purchase one
gear that mates with a variety of lenses.

Assembling the Focus Ring to your Manta Gear

Look at the drawing to the left and note which end of the lens the Focus
Ring slides onto. Then follow the instructions below.

1. Make sure your Focus Ring is in the unlocked position. Slide the Focus
Ring onto your lens from the front. Push until it won’t go any further.

2. Once on the lens, grasp the Focus Ring, then press and hold the red
latch on the Focus Ring while twisting the gray and red rings in opposite
directions until the white dots line up. (Note: the locked icon). The Focus
Ring is now locked onto the lens.

3. Set your lens to ‘manual’ focus. Then orient the Slip Ring as you see in
the drawing to your left, the white dot and switch do not line up. Push the
Slip Ring on until it stops. Next twist the Slip Ring counter clockwise until
the white dot is in the center of the switch.

4. Slide the Manta Gear on from the back of the lens. Align the white
dot on the Manta Gear with the unpainted red dot on the Focus Ring.
Then press the two parts together. Once the the two parts are fully
mated, while holding the Focus Ring with one hand, and pressing
the red Manta Gear latch with thumb, twist the Gear until the white
dots line up (note: the locked icon). The Manta Gear is now locked
onto the Focus Ring.

Disassembling the Focus Ring

1. Remove the Manta Gear by pressing and holding the latch on the
Manta Gear. Then twist it until the white dot on the Manta Gear is
lined up with unpainted red dot on the Focus Ring (note: the
unlocked icon).

2. Pull the Manta Gear off the lens.

3. Remove the Focus Ring by reversing the steps 1 and 2. above The
white dot and the unpainted red dot will not be lined up after step 2,
allowing you to slide the Focus Ring off your lens.

TOKINA FISHEYE10-17mm 3.5-4.5:2.8 (CANON)

MANTA FOCUS RING ASSEMBLY INSTRUCTIONS

TOKINA 10-17 LENS

GRAY/RED
FOCUS
RING

SLIP RING

NOTE:
DOT AND SWITCH
ARE NOT LINED UP

ROTATE SLIP RING UNTIL
DOT & SWITCH ARE LINED UP

FOCUS RING PROPERLY

LOCATED ON LENS

UNLOCKED
POSITION

ROTATE
FOCUS
RING INTO
LOCKED
POSITION

RED LATCH

LENS WITH
FOCUS RING
ATTACHED

HOOK THIS EDGE
OVER THE SWITCH
AND ROTATE RING
ONTO LENS

LENS WITH

FOCUS RING

ATTACHED

ONCE SLIP RING
IS OVER SWITCH
PUSH UNTIL IT
STOPS

TOKINA 10-17 LENS

GRAY/RED

SLIDE FOCUS RING
ONTO LENS FROM
BACK UNTIL IT STOPS

PRODUCT CODE: GM2201TK

TOKINA 10-17
LENS WITH FOCUS
RING, 1.4X EXTENSION
RING AND GEAR

TOKINA 10-17
LENS WITH FOCUS
RING, 2X EXTENSION
RING AND GEAR

Revsion 2.0 - APR2013

www.xit404.com

TOKINA FISHEYE 10-17mm 3.5-4.5:2.8 (CANON)

FOCUS RING ASSEMBLY INSTRUCTIONS AND WARRANTY INFORMATION

1.4X TELE
EXTENSION
RING

2X TELE
EXTENSION
RING

SHOWING
THE
UNLOCKED
POSITION

RED GEAR

LENS WITH
FOCUS RING
ATTACHED

ORIENT GEAR IN
THE UNLOCKED
POSITION

ROTATE INTO
LOCKED POSITION

RED LATCH

NOTE:

THE SLIP RING IS NOT NEEDED
WHEN USING TELECONVETERS

FDM parts - a brief description

Xit 404 manufactures a number of its parts using a process called Fused Deposition Modeling (FDM). This process involves extruding a thread of plastic and laying it down
in thin layers to build a part. This enables us to supply you products that enhance your underwater photography and videography.

Care and Maintenance

The FDM part is impact resistant and will withstand most drops from table height. However, as with all plastic parts, they cannot withstand excessive pressure and
force without breaking. Being careful means handling the product during assembly with a light touch, do not force.

If your part gets wet let it drip-dry for about an hour. If you have to pack it before it is dry then wrap it in something absorbent such as a paper towel, tee shirt or sock
and put it into a plastic bag. This will keep your other parts from getting dripped on.

FDM Plastic Part Warranty

FDM parts are guaranteed to be free of manufacturing defects for a period of one year from date of purchase. Unnecessary force can cause excessive wear and
possibly break the parts voiding warranty. Damaged or broken parts will be inspected. If Xit 404 determines that the parts were misused or abused, warranty will be void.
Valid purchase receipt isrequired for all warranty claims.