X1M Platinum [V3.01b]
HF TRANSCEIVER
XG
-----------------------------------------------------------------------------------------------------------------------------------------------------
Basic Parameters
Receive frequency range: 0.1~30MHz
Transmit frequency range: 3.5~3.9MHz
7.0~7.3MHz
14.0~14.35MHz
21.0~21.45MHz
28.0~29.7MHz
In order to comply with the requirements of corresponding countries and regions, others with frequency band are
forbidden to transmit!
Working mode: SSB (A3J)
CW (A1)
Receiving sensitivity: superior to 0.45uV
Radio frequency output power: ≥4.5W
Frequency stability: superior to 0.5ppm
Frequency accuracy: superior to 0.5ppm (start-up 5min)
Working voltage: 12.0~13.0V DC (heat generation can be reduced within this voltage range)
Receiving standby current: 0.5A
Emission current: 1.8A Max
Volume: 97*40*155（mm）
-----------------------------------------------------------------------------------------------------------------------------------------------------
Intellectual Property
Unauthorized by XG Radio team, the product and its copy of this Operation Guidebook is forbidden to
use for commercial purposes.
Tip:
This equipment is able to connect with any HAM RADIO DELUXE software, with any ICOM mode,
and IC-718 is recommended to select.
(Coordinate with serial adapter plate)
Services
QQ: 24438765
X1M Discussion Group: 301951091
Information Issue
http://blog.sina.com.cn/bg8ht
Be sure to read the following precautions!!!
1. Do not directly connect the serial port or USB-serial devices to the DB9 port on the tail of the machine (as DB9 port is also used as the
band signal output port, with voltage), so as to avoid damages to the serial device;
2. Do not open emit to avoid burning power amplifier tube; receiver, transmitter, please connect the appropriate shortwave antenna during
receiving and transmitting;
3. Generally, do not change settings under project menu after getting the machine, because each machine is individually debugging before
delivery. If there exist frequency deviation under a certain mode during use, it will be subject to fine tuning according to the deviation!
4. In order to avoid short circuit due to assembly errors at installation, please keep in mind the plug direction of adaptor during disassembly!!
Wire splice of power plug:
Core wire is positive, and the sheath is negative (inside positive and outside negative)
Key Operating Instructions
As for X1M Platinum, multi-function keys (F1 - F5) are pressed to operate the machine. The control portion includes 4
groups of menu in total, click the frequency knob to switch between menu groups. The related functions are described as
follows:
The first group of menu:
TS+: frequency step bit moving to the left for one bit;
MD: mode selection. Press it to show LSB-USB-CW ；
A/B: switching between VFOA and VFOB of the voltage controlled oscillator;
A=B: setting VFOB the same as VFOA;
TS-: frequency step bit moving to the right for one bit;
The second group of menu:
V/M: switching between the frequency mode and the channel mode;
MC: clearing the current channel storage in channel mode;
V>M: saving the current frequency and mode into the current channel if the current channel is empty;
The third group of menu:
PRE: preamplifier switch. Switch on the preamplifier, a white spot will be displayed before the at the upper left
corner of the screen, which means that the preamplifier is switched on; when the preamplifier is switched off, the white spot
becomes hollow.
ATT: pre-attenuator switch. X1M Platinum has no this function.
SPL: different-frequency T-R switch.
The fourth group of menu:
RIT: frequency tuning switch. Switching on the RIT and rotating the frequency knob for tuning frequency. When switching
off the RIT, the tuning data is automatically cleared;
MUT: system beep mute switch;
KYR: key mode selection. Manual/automatic mode and left-hand/right-hand mode are available.
LK/SYS key: short-press the key to lock the keyboard and the frequency knob, and a lock sign will be shown on the upper
right corner; long-press the key to enter the project menu setting interface.
Description of Project Menu
Note: Do not change the Project Menu settings in order to avoid abnormality of machine!
Press “LK/SYS” for 2s, and enter into the interface of project menu setting.
In the project menu mode, rotate the encoder knob to select options; if you want to select a setting function, rotate the encoder to the current
item, press the encoder to enter the setting status; F1 and F5 keys will move the current position to carry. Rotate frequency knob to increase or
decrease the number of selected bits.
01.IF OFST: medium frequency setting
the customer.
02.LSB BFO: BFO frequency setting under LSB mode
03.USB BFO: BFO frequency setting under USB mode
04.CW BFO: BFO setting under CW mode
05.CW TONE: Side tone settings under CW mode
06.CW TDLY: Emission delay setting under CW mode
07. KYR SPD: Automatic telegraph key transmission rate setting
08.TXP TIM: Long-term protection time settings, unit: s
09.BRITNES: Screen brightness setting
10.CNTRST: Screen contrast setting
11.FBND TX: Prohibition transmitter settings of non-amateur frequency
12.DDS CLK: DDS clock settings
13.DDS MLT: DDS multiple frequency setting
14.RST ALL: Reset of project menu parameters: selected this option, set 0 to 1, exit this option; and then press LK /
SYS key, rotate frequency knob and select yes, press the frequency knob again to exit the project
menu; finally, start up the machine again, the setting parameters of project menu will restore to the
default parameters.
After adjusting all settings, press the frequency
knob to exit, and then press the "LK / SYS" key,
the system prompts whether to save the settings
and displays "NO" and "Yes", rotate frequency
knob to select the appropriate option, and press
frequency knob again to exit from the project
menu.
全文完。
After-sales service
l The proper of the X1M Platinum is backed by one-year guarantee
(including amplifier tube, display screen, but excluding hand
microphone, chassis and DDS). In case of failure during the warranty
period, it will be repaired to the normal working condition for free. In
case of man-made damage, only the maintenance cost is charged.
l If the product software upgrade is available, the software shall be
upgraded for free.
l Out of the warranty period, lifelong maintenance services shall be
provided at cost price.
l Roundtrip logistics costs incurred for maintenance shall be borne by
Loading...