XIAMENSHI C CHIP TECHNOLOGY C 3051L Users Manual

C-3051L V1.0

XIA MEN SIXINWEI TECHNOLOGY CO., LTD.

Product Specification

Product name: WIFI BLE module

Product model: C-3051L

Document no. :

File version: V1.0

Effective date:

(OEM) Integrator has to assure compliance of the entire end-product incl. the integrated RF Module.
For 15 B (§15.107 and if applicable §15.107) compliance, the host manufacturer is required to
show compliance with 15 while the module is installed and operating.

Furthermore the module should be transmitting and the evaluation should confirm that the module's
intentional emissions (15C) are compliant (fundamental / out-of-band). Finally the integrator has
to apply the appropriate equipment authorization (e.g. Verification) for the new host device per
definition in §15.101.

Integrator is reminded to assure that these installation instructions

will not be made available to the end-user of the final host device.

The final host device, into which this RF Module isintegrated" hasto be labelled

with an auxilliary lable stating the FCC IDofthe RF Module,

such as "Contains FCC ID: 2AR7VC-3051L"

"This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions:

(1)this devicemay not cause harmful interference, and

(2)this devicemust accept any interference received, including

interference thatmay cause undesired operation."

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

--Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this unit not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

Module statement

The single-modular transmitter is a self-contained, physically delineated, component
for which compliance can be demonstrated independent of the host operating
conditions, and which complies with all eight requirements of § 15.212(a)(1) as
summarized below.

1) The radio elements have the radio frequency circuitry shielded.

2) The module has buffered modulation/data inputs to ensure that the device will
comply with Part 15 requirements with any type of input signal.

3) The module contains power supply regulation on the module.

4) The module contains a permanently attached antenna.

5) The module demonstrates compliance in a stand-alone configuration.

6) The module is labeled with its permanently affixed FCC ID label

7) The module complies with all specific rules applicable to the transmitter, including
all the conditions provided in the integration instructions by the grantee.

8) The module complies with RF exposure requirements.

This transmitter/module must not be collocated or operating in conjunction with any
other antenna or transmitter.

C-3051L V1.0

XIA MEN SIXINWEI TECHNOLOGY CO., LTD.

Catalogue

1. product overview： ............................................................................................................................... 3

2. Application field： ................................................................................................................................. 3

3.Basic features： .................................................................................................................................... 4

4.Block diagram: ....................................................................................................................................... 6

5.performance parameters： .................................................................................................................... 7

6.Module size drawing： ........................................................................................................................... 8

7.Module footer definition figure: ............................................................................................................... 9

8.Pin function description： .................................................................................................................... 10

9.Matters needing attention： ................................................................................................................. 10

10.Recommended reflux temperature: .................................................................................................... 11

11.Application schematic diagram: .......................................................................................................... 11