Xiamen Intretech 0000G2 User Manual

Installation Steps

FAQ and Tips

MEMOBIRD has two print modes: Cloud Mode and Local Mode.

Cloud Mode: Requires Wi-Fi and Internet.

Local Mode: Does not require Wi-Fi or Internet.

(NOTE: Before Local Mode can be enabled for the first time, setup and registration

must first be completed in Cloud mode, with an internet connection.)

Cloud Mode (set up before using Local Mode for the first time)

Step 1

Please power on MEMOBIRD. Green light will turn on.

Step 2

Please turn on Wi-Fi on your phone, and make sure your phone
is

connected to the Internet.

Step 3

Please scan the QR code in the bottom right comer below. Download the App,
and register a new account.

Step 4

Turn on the switch on the bottom of MEMOBIRD. The Cloud Mode icon " "
should be displayed.

Step 5

Please double click the button on the front of MEMOBIRD, and scan the QR
code using your phone to bind a new device (your phone) .

Step 6

Please press the button on the front of MEMOBIRD for 6 seconds to set
Wi-Fi. Ensure your phone and MEMOBIRD are on the same Wi-Fi
network. Enter the password for your Wi-Fi network.

Local Mode (after setup in Cloud Mode)

Step 1

Please turn off the switch at the bottom of the MEMOBIRD, and hide the
icon

" "

, namely Local Mode.

Step 2

On your phone connect to the "MEMOBIRD " Wi-Fi network listed. Enter
the password printed out on MEMOBIRD.

★ Please use only the MEMOBIRD power adaptor

supplied.

★ 5G Wi-Fi networks are not supported.
★ Your phone will not receive Wi-Fi traffic from

other sources when in Local Mode.
☆ Double click the front button to print a diagnostic

report.
☆ Press and hold the front button for 6 seconds to

reset Wi-Fi settings.
☆ Switch the bottom switch to toggle between

Cloud Mode and Local Mode.

☆ Orange LED: Important Message.

(restore when pressing the button)

☆ Red LED: Overheated or out of paper.
☆ Blue LED : In Local Mode.
☆ Green LED On: Normal status/ Ready.
☆ Green LED flashing: Flashes during printing or

network connection.

80℃

Note- Print head temperature

is 80°C. Please do not touch.

Note-Sharp paper cutting blade.Please do
not touch.

Contact Information

Support and Customer Service :
email [e-mail]

Hot line: 400-8613-222

(Monday to Friday 8:00-17:30）

App Download

Quick Installation Guide

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device
must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the us
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
RF Exposure: A distance of 20 cm shall be maintained between the antenna and users, and the transmitter may not be co-located with any other transmitter or antenna.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
This equipment complies with Canada radiation exposure limits set forth for uncontrolled environments. This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.

The distance between user and products should be no less than 20cm
la distance entre l'utilisateur et les produits devraient être au moins 20 cm

er is