Xfinity Remote User Manual
Back
4
Remote with Voice Control
Start
Meet Your Remote Turn On Your Remote
1 32
Your remote arrives with the AA batteries
already installed, but not activated. Here is
how to power it on for the rst time.
TV Power
Status LED
All Power
Voice Control
Push and hold to ta lk. Discover co ntent
by chann el, program or key words .
XFINITY / Menu
Access Gu ide, Saved, XFINIT Y On Demand,
Apps, S earch and Set tings.
Pick up your remote and remove the “Pull”
A
tab (on back) by pulling away from the
remote. The Status LED will blink green
four times as the remote powers up (about
5 seconds).
Pair Remote for “Aim
Anywhere” Control
Control your set-top box without having to
point your remote at the device, even
when it is located inside a cabinet or
entertainment center.
Press and hold the Setup button (about 3
A
seconds) until the Status LED changes
from red to green.
Press the XFINITY button.
B
Number Keys
Use pre dictive tex t (T9) to quickl y search
for content.
TV Input
Change s to the next av ailable inpu t on
your T V (if program med in Step 4).
Setup
Progr am remote for Aim Anyw here or
to control your T V or audio device.
Turn on your TV.
B
Turn on your set-top box.
C
Follow the on-screen instructions to enter
C
the 3-digit code that appears.
Once the code is correctly entered, your
XFINITY Remote is paired with the device.
Not working? Make sure the battery tab from
your remote is removed, your TV is on and you are
entering the correct 3-digit code on your TV screen.
Need to r emove Aim Anywhere co ntrol? Press
and hold the Setup button on the remote until the
status LED changes from red to green. Press A on
the remote. If the status LED blinks green twice,
you have successfully removed Aim Anywhere.
Need help ?
Visit xnity.com/voiceremote
Use the My Account app
Start
for Mobile (iOS/Android) or X1
Remote with Voice Control
Control Your TV’s Power and Volume
4
Using the list on the right, nd the rst 5-
A
digit code for your TV manufacturer.
Press and hold the Setup button (about 3
B
Popular Manufacturer Codes
seconds) until the Status LED changes
from red to green.
Enter the rst 5-digit code for your TV
C
manufacturer. The Status LED should ash
green twice.
Verify that the code was accepted by using
D
your remote to adjust volume and turn the
TV on and o.
LG 1017 8 , 112 6 5
Panasonic 10051, 10250
Samsung 10812, 10060
Sanyo 1015 4, 10159
Sony 10000, 11100
Sharp 100 93, 10165
Toshiba 1015 6, 1115 6
Vizio 11758 , 117 5 6
If your code isn’t listed or you would
like to control an audio device, visit
xnity.com/voiceremote.
Not working? Try the second code listed. Still
not working? Visit xnity.com/voiceremote for a
complete list of codes or use the My Account app
for mobile (iOS/Android) or X1.
Test Voice Control
5
Once your remote is paired with your set-top
box, you can use voice control.
Press and hold the Voice button until you
A
hear the audio tone.
Speak a voice command to the remote
B
while continuing to hold down the button.
Try one of the suggestions below. The
Status LED will be solid blue while you
speak your command.
WATCH CNBC
FIND The Voice
SHOW ME all Eagles games
SHOW ME all kids mov ies on HBO
RECORD The Bigges t Loser
LAUNCH Pandora
GUIDE
WHAT SHOUL D I WATCH?
WHAT’S ON N OW?
FCC Compliance Statement
This equipment has been tested and found to comply with
the limi ts for a Class B dig ital de vice, pu rsuant to part 15
of the FCC rules. T hese lim its are design ed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can r adiate r adio frequency ener gy and, i f not use d
in accordance with the ins truc tions, m ay cause harmf ul
inter ference to radi o communications.
There is no guara ntee that inter ference wil l not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Incre ase or decrea se the separa tion betwe en the
equipment and receiver.
• Connect the equip ment into an outle t on a circuit
dier ent from that w hich the receiver is connected .
• Consult the dealer or an experienced remote control
/T V technician for help.
• It is st rongly recom mended that the TV be p lugged
into a sep arate wall outlet.
The user is cautioned that changes and modications made
to this equipment without the approval of the manufacturer
could vo id the user’s a uthority to opera te this equipme nt.
This device complies with part 15 of the FCC rules. Operation
is subje ct to the f ollowi ng two co nditio ns: (1) This devi ce
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
“Caution” : Exposure to Radio Frequency Radiation. Antenna
shall be mounted in such a manner to minimize the potential
for human contact during operation to avoid the possibility of
exceed ing the FCC radio f requency exposu re limit.
Radio Exposure Statement: This equipment complies with
the FCC radiation exposu re limit s set forth fo r devices
operating in an uncontrolled environment. This equipment
should be oper ated with a minimu m distance of 2 cm
betw een the r adiator and front of face . This equipment
should not be pla ced directl y on the ear when the speake r
is acti ve.
Keep for futur e reference, b ut if you
decide to toss, please recycle.
Quick St art Guide v.1.0
1698397C Prin ted in China
Release the Voice button when your
C
command is complete. Look at the TV for
the results of your voice command.
Not working? Make sure yo u’re pressin g the
Voice but ton while you speak into the remo te,
and rel ease it when com plete.
Loading...