Xerox XM3-19w User Manual

LCD Monitor
User’s Guide
XM3-19w
LCD Monitor
©2006 by Xerox Corporation. All rights reserved.
Copyright protection claimed includes all forms and matters of copyrightable material
and information now allowed by statutory judicial law or hereinafter granted, including without limitation, material generated from the software programs which are displayed on the screen such as icons, screen displays, looks, etc.
of XEROX CORPORATION. Other company trademarks are also acknowledged.
Changes are periodically made to this document. Changes, technical inaccuracies, and typographic errors will be corrected in subsequent editions.
2
Xerox© LCD Monitor User’s Manual
Table of Contents
CE Marking Declaration Of Conformity .................................................4
Federal Communications Commission (FCC) Statement ....................5
Important Safety Instructions .................................................................6
1 Introduction
Features ........................................................................................................9
Package Contents ....................................................................................... 10
Front View and Controls .............................................................................. 11
2 Installation
Connecting Your LCD Monitor to a Computer ............................................ 12
Method 1 : Analog (D-SUB) Connection ................................................. 12
Method 2 : Digital (DVI) Connection) ......................................................14
Installing Your LCD Monitor .........................................................................16
3 OSD Menu
Using the OSD Menu ..................................................................................17
The OSD Options ........................................................................................ 18
The picture Options ..................................................................................... 19
The advanced Options ................................................................................ 20
The audio Options ....................................................................................... 21
The options Options .................................................................................... 22
The utilities Options .....................................................................................23
4 Technical Information
Preset Mode Timing Chart ...........................................................................24
DVI Connector PIN Assignment .................................................................. 25
D-SUB Connector PIN Assignment .............................................................26
Plug and Play ..............................................................................................27
Visual Inspection ......................................................................................... 27
Troubleshooting ........................................................................................... 28
Specifications .............................................................................................. 29
Authorized Service Centers ......................................................................... 30
ENGLISH
3Xerox© LCD Monitor User’s Manual
Recycling Place
EUROPE When disposing of Xerox Branded Monitors in Europe, please contact one of the following three locations to make arrangements for recycling.
Proview International (UK) Limited 30 The Avenue, Watford, Hertfordshire WD17 4AE United Kingdom Timothy Lo Tel: +44 1923-248-111 Fax: +44 1923-248-222 Email: tim.lo@proview.co.uk
PGL Europe B.V. (Proview Group Limited Rotterdam) Satijnbloem 37, 3068 JP Rotterdam Hollande David Hsieh Tel: +31-10-238-1090 Fax: +31-10-238-1091 Email: david@proview-group.nl
e-back GmbH Sondermoninger Straße 5,83339 Chieming Ullrich Didszun Tel: +02234/9859-11 Fax: +02234/9859-60 Email: e-back@rde-gmbh.de
ASIA When disposing of Xerox Branded Monitors in Asia, please contact the following location to make arrangements for recycling.
Proview Technology (ShenZhen) Co., Ltd. North Block 21, 23# Shatoukok Free Trade Zone, ShenZhen, China. Mr. Dennis Chang Tel: +86-755-2526-1512
Fax: +86-755-2526-1565 Email:recycling@proview.com.cn
AMERICA When disposing of Xerox Branded Monitors in America, please call the following location to make arrangements for recycling.
Proview Technology, Inc. (U.S.A.) 7373 Hunt Avenue, Garden Grove, CA 92841 U.S.A. Patrick Yen Tel:714-799-3865 Fax:714-379-6290 Email:pyen@proview.net
“THIS DISPLAY UNIT IS AN ELECTRIC DEVICE WHICH MAY CONTAIN HAZARDOUS MATERIALS AND COMPONENTS, AND WHICH MUST BE DISPOSED OF AT END OF LIFE ACCORDING TO THE PROPER PROCEDURE”
FCC/CE
4
Xerox© LCD Monitor User’s Manual
CE Marking Declaration Of Conformity
This LCD monitor complies with the requirements of the EC Directive 89/336/EEC “EMC Directive” and 73/23/EEC “Low Voltage Directive” as amended by Directive 93/68/EEC. The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterized by their connection to the public low voltage power supply system.
FCC/CE
ENGLISH
5Xerox© LCD Monitor User’s Manual
This equipment has been tested and found to comply with the limits of a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient/Relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit which is different from what the receiver is connected to.
4. Consult the dealer or an experienced radio/TV technician
for help.
CAUTION:
Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user authority to operate the equipment.

Federal Communications

Commission (FCC) Statement

Important Safety Instructions

6
Xerox© LCD Monitor User’s Manual
To prevent any injuries, the following safety precautions should be observed in the installation, use, servicing and maintenance of this equipment.
Before operating this equipment, please read this manual completely, and keep it nearby for future reference.
Important Safety Instructions
Warnings
• Do not place the equipment on any uneven or unstable carts, stands, tables, shelves etc. The equipment may fall, causing serious injury to children or adults and serious damage to the equipment itself.
• Use only a cart or stand recommended by the manufacturer. This equipment and recommended cart or stand should be handled with care. Quick stops, excessive force, and uneven surfaces may cause the equipment and cart/stand to overturn.
• Do not disable the 3-wire grounding type plug. The grounding pin on the 3-prong plug is an important feature. Removing the grounding pin will increase the risk of damaging the equipment. If you can not fit the plug into the electrical outlet, contact an electrician to install a grounding outlet.
• Always operate this equipment from the type of power source indicated on the rear of the serial/model plate.
• Never overload wall outlets and extensions.
• Use and handle the power cord with care.
• Do not place any heavy objects on the AC power cord.
• Do not pull the AC power cord. Do not handle the AC power cord with a wet hand.
Important Safety Instructions
ENGLISH
7Xerox© LCD Monitor User’s Manual
• Do not touch the power cord and antenna cable during lightning.
• Remove the plug from the wall outlet if the equipment will not be used for a long period of time.
• Do not place, use or handle this equipment near water.
• Never expose the equipment to liquid, rain, or moisture.
Seek qualified service if any of the above is spilled into the
equipment.
• Do not attempt to service the equipment yourself.
• Opening and removing the covers may expose you to dangerous voltage or other hazards and may void your warranty. Refer service to qualified personnel.
• Always remove the power cord from the outlet before cleaning the equipment.
• Never use liquid or aerosol cleaners on the equipment. Clean only with a soft dry cloth.
• Do not expose the equipment to extreme temperature or to direct sunlight, as the equipment may heat up and suffer damage.
• Do not install the equipment near any heat sources such as radiators, heat registers, stoves, or any other apparatus that might produce heat.
• Do not block any ventilating openings. Leave an open space around the equipment.
• Never place the equipment :on a bed, sofa, rug, or any other similar surfaces; too close to drapes/curtains/walls, in a bookcase, built-in cabinet, or any other similar places that may cause poor ventilation.
(continued on next page)
Important Safety Instructions
8
Xerox© LCD Monitor User’s Manual
• If any of the following conditions occur, unplug the power cord from the outlet and request service from qualified personnel.
a. The power cord or plug is damaged. b. Liquid is spilled into the product . c. An object falls onto or into the product. d. The product has been dropped or damaged. e. The product’s display is abnormal.
DISPOSAL OF WASTE ELECTRONIC EQUIPMENT BY PRIVATE HOUSEHOLDS WITHIN THE EUROPEAN UNION
This sign indicates that this product may not be disposed of with your regular household waste. The recycling and separate collection of such products is your responsibility. Please drop off the above-mentioned waste at a designated place for recycling waste electrical and electronic equipment. If you do not know where to drop off your waste equipment for recycling, please contact your local city office or household waste
collection service.
9Xerox© LCD Monitor User’s Manual

Introduction

ENGLISH
• Rapid Video Response Fast action media such as gaming, DVD and video
conferencing will playback smoothly thanks to the rapid video response time of the LCD panel.
• High Contrast Ratio Colors will appear vibrant and lifelike producing superior
image quality.
• Plug-and-Play Capability Easy trouble-free configuration and set-up.
• Very High Resolution The 19” wide screen has the outstanding 1440x900
resolution. It can make the image displayed more precise. XM3-19w is excellent to be your first wide screen monitor.
• Multimedia Enhanced Speakers True multimedia sound without using valuable desktop
space. The XM3-19w features two built-in stereo speakers integrated into the stylish design.
• Wall-Mounting Capability Compatible with the VESA industry standard for wall/arm
mounts to save valuable desktop space.
1 Introduction
Features
10
Xerox© LCD Monitor User’s Manual
Introduction
Make sure the following items are in the box.If any items are missing, please return this product to the original place of purchase.
CAUTION:
Be sure to save original box and all packing material for future transport of monitor.
AC
Power Cord

Package Contents

LCD Monitor
Quick Guide
Warranty
Card
CD-ROM
(Driver/Manual)
 


 
D-SUB Cable
 


 
AUDIO Cable
11Xerox© LCD Monitor User’s Manual
Introduction
ENGLISH

Front View and Controls

▼▲
In OSD mode, press the ▲/▼ buttons to select the desired
menu. Adjusts the speaker volume up and down.
MENU
Press once to display the OSD (On Screen Display). And
press again to activate the desired setting.
LED The LED light indicates when the LCD monitor is activated
(blue light indicates power on and amber light indicates power saving).
Turns the LCD monitor on and off.
AUTO Press to automatically adjust the display settings to optimize
performance based on the D-SUB signal.
1
2
3
4
5
1
2
3 4
5
Installation
12
Xerox© LCD Monitor User’s Manual
1 Turn off the computer and unplug the power cord.
2 Connect the signal cable to the D-SUB port on the back of
the computer.
3 Connect the audio cable to the line-in port on the back of the
computer.
Refer to the owner’s manual of the computer for connections. In the process of connecting external equipment, do not connect any AC power cords to wall outlets until all other connections are completed.
2 Installation
Connecting Your LCD Monitor to a Computer
Method 1 : Analog (D-SUB) Connection
Connect to power source
Connect to the D-SUB port
2
4
Connect to the Line-in port
3
Installation
ENGLISH
13Xerox© LCD Monitor User’s Manual
4 Connect the power cord to the LCD monitor and wall outlet.
5 Press the button, located on the bottom side of the main
unit to turn the monitor on, then turn the computer on. If the monitor displays an image, the monitor is successfully installed. If no image is displayed, check all connections.
NOTE:
Unplug the monitor before installation to avoid electric shock or damage.
NOTE:
The button is used for switching the LCD monitor on and off, it does not disconnect the device from the main voltage. To completely disconnect the main voltage, please remove the power plug from the socket.
NOTE:
The LED indicator is blue when the monitor operates normally and will turn to amber when in power saving mode. When the monitor is off, the LED turns dark.
Installation
14
Xerox© LCD Monitor User’s Manual
Method 2: Digital (DVI) Connection
1 Turn off the computer and unplug the power cord
2 Connect the DVI signal cable (not included) to the DVI port
on the back of the computer.
3 Connect the audio cable to the line-in port on the back of the
computer.
4 Connect the power cord to the LCD monitor and wall outlet.
5 Press the button, located on the bottom side of the main
unit to turn the monitor on, then turn the computer on. If the monitor displays an image, the monitor is successfully installed. If no image is displayed, check all connections.
6 When the DVI and VGA input ports are connected at the
same time, press down the AUTO button after 3 seconds to switch between the VGA mode and DVI mode.
Installation
ENGLISH
15Xerox© LCD Monitor User’s Manual
Connect to power source
4
2
Connect to the DVI port
Connect to the Line-in port
3
The wide-screen display enables you to view your content in a brand new way. The next generation of computing environments and game consoles are planning to support wide­screen resolutions.
■ Multitask - view applications side by side and reduce toggling between them.
■ Enrich - view DVD films in their native wide format for an enhanced multimedia experience.
■ Experience - enjoy gaming action at higher wide-screen resolution.
However, having the effective wide resolution (WXGA+, 1440x900), you need to select the correct setting in your Display Property of Windows® system.
Please note, some video cards and PCs with integrated video will not probably support the wide-screen resolutions. You have to update the video chip/card driver or even
purchase a new video card to utilize the advantages of the wide-screen.
For your PC, refer to the available drivers and downloads from the PC manufacturer’s web site. For upgraded video card, refer to the video card manufacturer’s web site: nVIDIA® (www. nvidia.com), ATI® (www.ati.com), S3® (www.s3graphics.com), Intel® (www.intel.com) and so on.
HOW TO GET SUPPORT FOR YOUR WIDE SCREEN?
Installation
16
Xerox© LCD Monitor User’s Manual
Installing Your LCD Monitor
Follow the instructions below to set up and install the monitor.
1 The package contains:
Display unit Stand
2 Cover an even stable surface with a soft cloth. Place the unit
face-down on the cloth. Fit the stand onto the bottom of the display unit as shown, then push until the two latches snap into their sockets.
LATCHES
LATCH
SOCKETS

OSD Menu

ENGLISH
17Xerox© LCD Monitor User’s Manual
To create the best picture, your XM3-19w has been preset at the factory with the Preset Mode Timing shown on page 24. The OSD (On Screen Display) Menu allows the user to adjust various settings and options by following the steps below.
1 Press the MENU button to display the OSD. The OSD main
menu provides an overview of the selection of controls available.
2 Press the ▲ or ▼ button to highlight the desired icon. Then,
press the MENU button to activate the highlighted icon.
3 Press the ▲ or ▼ button to select the desired adjustment
icon. Then, press the MENU button.
4 Press the ▲ or ▼ button to change the value of the selected
item.
5 Select the exit icon to exit the OSD.
6 Repeat steps 1 through 4 to make further adjustments. All
changes are stored immediately.
Using the OSD Menu
3 OSD Menu
picture
advanced
audio
options
utilities
reset
exit
auto adjust <up>to select
brightness
contrast
h position
v position
phase
clock
exit
OSD Menu
18
Xerox© LCD Monitor User’s Manual
picture
advanced
audio
options
utilities
reset
exit
auto adjust <up>to select
brightness
contrast
h position
v position
phase
clock
exit
The main menu includes the following options:
picture Adjusts picture settings such as brightness, contrast.
advanced Allows selection of the general color tint: CUSTOM COLOR,
WARM, or COOL.
audio Allows selection of the sound options and effects.
options Adjusts picture settings such as H/V position, H size and
phase.
utilities Adjusts the setting of the display time of the on-screen menu.
Allows selection of the language used on all the on-screen
menus.
reset
Restores the factory settings.
exit
Exits the on-screen menus.
The OSD Options
OSD Menu
ENGLISH
19Xerox© LCD Monitor User’s Manual
picture
advanced
audio
options
utilities
reset
exit
auto adjust <up>to select
brightness
contrast
h position
v position
phase
clock
exit
1 The picture menu provides access to the following menus:
The picture Menu
2 The picture menu includes the following options:
ON DESCRIPTION
auto adjust
Automatically adjust the display settings to optimize
performance based on the D-SUB signal.
brightness Controls the overall brightness.
contrast Controls the difference between the brightest and darkest
regions of the picture.
h. position Adjusts the position of the picture left and right in the
window.
v. position Adjusts the position of the picture up and down in the
window.
phase
Adjusts signal phase, which can improve focus clarity and image stability.
clock
Adjusts the width of the picture.
exit
Exits the picture menu.
OSD Menu
20
Xerox© LCD Monitor User’s Manual
2 The advanced menu includes the following options:
ON DESCRIPTION
sharpness
Increase this setting to see crisp edges in the picture;
decrease for soft edges.
color
Allows selection of the general color tint: user, natural, warm, or cool.
cool
Inclines colors toward the blue end of the spectrum. Fixes the red, green and blue component levels at factory settings; they cannot be independently adjusted.
natural
Inclines colors toward the natural end of the spectrum. Fixes the red, green and blue component levels at factory settings; they cannot be independently adjusted.
warm
Inclines colors toward the red end of the spectrum. Fixes the red, green and blue component levels at factory settings; they cannot be independently adjusted.
user
Allows the user to adjust red, green and blue color component levels independently.
exit
Exits the advanced menu.
1 The advanced menu provides access to the following menus:
The advanced Menu
picture
advanced
audio
options
utilities
reset
exit
sharpness 1 2 3 4 5
color cool natural warm user
user red
user green
user blue
exit
OSD Menu
ENGLISH
21Xerox© LCD Monitor User’s Manual
2 The audio menu includes the following options:
ON DESCRIPTION
volume
Adjusts the speakers volume up and down.
mute
Mutes and restores the monitor speakers sound.
exit
Exits the audio menu.
1 The audio menu provides access to the following menus:
The audio Menu
picture
advanced
audio
options
utilities
reset
exit
volume
mute on off
exit
OSD Menu
22
Xerox© LCD Monitor User’s Manual
2 The options menu includes the following options:
ON DESCRIPTION
osd h. position
Moves the OSD left and right in the window.
osd v. position
Moves the OSD up and down in the window.
exit
Exits the OSD menu.
1 The options menu provides access to the following menus:
The options Menu
picture
advanced
audio
options
utilities
reset
exit
osd h position
osd v position
exit
OSD Menu
ENGLISH
23Xerox© LCD Monitor User’s Manual
2 The utilities menu includes the following options:
ON DESCRIPTION
osd timeout
Allows selection of the display time of the on-screen menu.
osd background
Controls the translucence of the on-screen menu’s background.
languages Allows selection of the languages used on all the on-screen menus.
exit
Exits the utilities menu.
1 The utilities menu provides access to the following menus:
The utilities Menu
picture
advanced
audio
options
utilities
reset
exit
osd timeout 15 seconds
osd background opaque translucent
language
exit
Technical Information
24
Xerox© LCD Monitor User’s Manual
The screen image has been optimized during manufacture for the display modes listed below.
Video signal: (IBM PC/AT)
Dot X Line
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
720 x 400 31.47 70.00
640 x 480 31.47 60.00
37.86 72.80
37.50 75.00
800 x 600 35.16 56.25
37.88 60.30
48.08 72.20
46.87 75.00
1024 x 768 48.36 60.00
56.48 70.10
60.02 75.00
1280 x 1024 63.98 60
79.98 75
1440 x 900 55.47 59.90
70.64 74.98

Preset Mode Timing Chart

4 Technical Information
Technical Information
ENGLISH
25Xerox© LCD Monitor User’s Manual
PIN DESCRIPTION PIN DESCRIPTION
1 TMDS Data 2- 15 GND
2 TMDS Data 2+ 16 Hot Plug Detect
3 TMDS Data 2/4 shield 17 TMDS Data 0-
4 18 TMDS Data 0+
5 19 TMDS Data 0/5 shield
6 DDC Clock 20
7 DDC Data 21
8 Analog Vertical Sync 22 Clock shield
9 TMDS Data 1- 23 Clock +
10 TMDS Data 1+ 24 Clock -
11 TMDS Data 1/3 shield C1 Analog red
12 C2 Analog green
13 C3 Analog blue
14 +5V Power C4 Analog
1 8
169
17 24
C1 C2
C3 C4
DVI Connector PIN Assignment
Technical Information
26
Xerox© LCD Monitor User’s Manual
PIN DESCRIPTION
1 Red
2 Green
3 Blue
4 Ground
5 Self Test
6 Red Ground
7 Green Ground
8 Blue Ground
9 5 VDC
10 Ground
11 Ground
12 SDA (FOR DDC)
13 H. Sync
14 V. Sync
15 SCL (FOR DDC)
1 5
6
11
5
10
1

D-SUB Connector PIN Assignment

Technical Information
ENGLISH
27Xerox© LCD Monitor User’s Manual
Permanently unlit or lit pixels
The standard of production techniques today cannot guarantee an absolutely fault free LCD display. A few isolated permanently lit or unlit pixels may be present. The maximum permitted number of pixel faults is stipulated in the stringent international standard ISO 13406-2 (Class II).
Example: A 17” flat-screen monitor with a resolution of 1280 x 1024 has 1280 x 1024 = 1310720 pixels. Each pixel consists of three subpixels (red, green and blue), so there are about 4 million dots in total.
According to ISO 13406-2 (Class II), a maximum of 6 pixels and 7 subpixels may be defective, i. e. a total of 25 faulted dots. This corresponds to approx. 0.002 % of the entire screen surface.
Visual Inspection
This monitor conforms to the VESA DDC (Display Data Channel) standard, which means that when it is used with a DDC compatible video card, the monitor is easier to set up. With VESA DDC 1/2B, when the monitor is turned on, it will automatically notify a windows 9X/2000/XP host computer of its scanning frequencies, capabilities and characteristics. Windows 9X/2000/XP will automatically recognize the presence of the monitor and select the appropriate display resolution.
Plug and Play
Technical Information
28
Xerox© LCD Monitor User’s Manual
Before consulting service personnel, check the following chart for a possible cause and solution to the trouble you are experiencing.
Monitor will not turn on
Make sure the power cord is plugged in.
No picture
Make sure the power cord is plugged in.
Check the signal cable connecting the LCD monitor
and the computer (refer to page 12-15).
Press the button on the front panel of the monitor.
Poor picture or abnormal picture
Check the D-SUB cable connecting the LCD monitor
and the computer (refer to page 12-15).
Press the MENU button to adjust the Brightness
Contrast option in the OSD.
Adjust the Color Select option in the OSD.
Press the AUTO button on the front panel of the
monitor, to automatically adjust the display mode.
Out of range message appears
Press the AUTO button on the front panel of the
monitor, to automatically adjust the display mode.
Press the MENU button to adjust the V Position, H
Position and H Size options in the OSD.
If using Windows 9X/2000/XP, wait a few seconds;
once Windows detects the problem, a dialog will appear allowing you to manually set up the video mode according to the preset mode timing chart
(refer to page 24).

Troubleshooting

Technical Information
ENGLISH
29Xerox© LCD Monitor User’s Manual
Specifications
MODEL
XM3-19w
LCD Panel Panel Size 19”w TFT LCD
Brightness 300
Contrast Ratio 500:1
Dot Pitch 0.284mm x 0.284mm
Speakers Built-In
Max. Resolution 1440x900
Input Connector D-SUB x 2/ DVI x 1/PC AUDIO
Power Source AC100-240V, 50-60Hz
Power Consumption 48W
Dimension 457x371x210 mm
Changes are periodically made to this specifications. Current specifications may also be obtained via the internet, www.xerox-displays.com or www.xerox-displays.info
Technical Information
30
Xerox© LCD Monitor User’s Manual
U.S.A. CALIFORNIA: AUTHORIZED SERVICE CENTER 7373 HUNT AVENUE GARDEN GROVE, CA 92841 (714) 799-3899 (800) 469-1175 (714) 379-6290 Fax Hours: 8AM ~ 6PM - Pacific Standard Time
TEXAS: AUTHORIZED SERVICE CENTER 10849 KINGHURST SUITE # 120 HOUSTON, TX 77099 (281) 530-4100 (281) 530-4104 Fax Hours: 8AM ~ 6PM - Central Time
EUROPE AUTHORIZED SERVICE CENTER CONTACTS: XOAL BVBA RAKETSRAAT 100 B-1130 BRUSSEL BELGIUM E-EMAIL: rma@proview-repair.com http://www.proview-repair.com Hotline: 00800 00 88 77 66 Fax: +32-2-725-2513 Hours: 10AM ~ 12PM and 2PM ~ 5PM Monday through Friday
Authorized Service Centers
Loading...