Xerox Fiery X2 V1.01 Expectation Setting Document
Expectation Setting Document for Fiery X2 V1.01
Digital Front End for 5765, 5790 DocuColor 5750/ 5799
Customer Support
The Xerox Customer Support Centers are available to provide general information, answer questions and take
service calls. You can reach the Customer Support Center at the following toll-free phone numbers:
United States 1-800-821-2797
Canada 1-800-939-3769
Your Xerox Color Analyst will provide fee-based training upon request.
General Specifications
Physical and Environmental
Server English Units Metric Units
Weight 12 lb. 5.44 kg.
Dimensions 10 x 6 x 14 inches 24 x 14.4 x 33.6 cm
Operating Temperature 50º - 104º F 10º - 40º C
Relative Humidity 5% to 95% (noncondensing) 5% to 95% (noncondensing)
Altitude 0 to 10,000 ft. 0 to 3,048 m
Electrical Requirements and Compliance
Server
Line Voltage 100 to 125 / 200 to 240 VAC RMS single phase, automatically configured
Frequency 50 to 60 Hz single phase
Power 150 W maximum
Fiery X2 Optional Kits
•
Token Ring Connectivity Kit
•
X-Rite DTP32 Densitometer
•
BNC Transceiver
Fiery X2 Specifications
•
200 MHz R5000 MIPs Processor
•
160 MB RAM
•
2 GB IDE hard drive
• 10/100 BaseT Network capability
Terms and product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.
Post Launch Version 26 May 1999
Page 1 of 7 X2_Majestik_ced.doc
Expectation Setting Document for Fiery X2 V1.01
Digital Front End for 5765, 5790 DocuColor 5750/ 5799
Network Specifications
Protocol Stack Printing
Services
Novell IPX / SPX
TCP / IP LPD Ethernet_II
TCP / IP SMB Ethernet_II
AppleTalk PAP Ethernet SNAP
PServer Ethernet 802.2
Ethernet 802.3
Ethernet_II
Ethernet SNAP
Token Ring 802.2 (option)
Token Ring SNAP (option)
Token Ring SNAP (option)
Token Ring SNAP (option)
(EtherTalk Phase 2 only)
Supported Frame Types Platform
Windows NT
Windows 95
Windows 3.1
Windows NT
Windows 95
Solaris 2.4
SunOS 4.1.x
Windows NT
Windows 95
Windows NT 4.0
Macintosh
The customer is responsible for supplying one network drop to enable the install.
Printing
STARR Compression
• The Compression efficiency is dependent on file type and complexity. Artifacts may be possible when
compression is selected depending on the file complexity.
• STARR Compression must be selected to support the advanced features in Fiery Options; i.e., collation, reverse
order, etc.
Print Speed / System Performance
• The maximum print speed for the X2 system is limited by the print speed of the 5765, 5790 and DocuColor 5750/
5799.
• The 5765, 5790 and DocuColor 5750/ 5799 are document printers; therefore the print engine will not cycle up until
the entire job is ready. This will impact First Copy Out Time (FCOT) when STARR Compression is in use. The
copier may cycle down between each job depending on job complexity.
• Overall system performance (‘Click to Clunk’ time) is primarily dependent upon the software applications and
network environment being used. Rasterizing (RIP-ing) is only a small fraction of Click to Clunk time.
• Printing with custom software applications may produce unexpected or unknown results.
Terms and product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.
Post Launch Version 26 May 1999
Page 2 of 7 X2_Majestik_ced.doc
Expectation Setting Document for Fiery X2 V1.01
Digital Front End for 5765, 5790 DocuColor 5750/ 5799
Maximum Image Sizes
• The maximum image size from an application is limited to the image size produced by the 5765, 5790 and
DocuColor 5750/ 5799. The application and the 5765, 5790, DocuColor 5750/ 5799 setup controls image position.
• Non-imageable area for the DocuColor 5790/ 5799 is listed as follows:
Leading Edge Trailing Edge Near Edge Far Edge
8mm 3mm 3mm 3mm
• Non-imageable area for the DocuColor 5750 is listed as follows:
Leading Edge Trailing Edge Near Edge Far Edge
5mm 5mm 3mm 3mm
INCLUDE TABLE FOR MAJESTIK
IOTs Supported
• 5765, 5790 and DocuColor 5750/ 5799.
Printer Driver Support
• Adobe 3.0.1 for Windows 3.x
• Adobe 4.2.2 for Windows 95
• Windows NT 4.0 (Microsoft PPDs only are supplied)
• Adobe PSPrinter 8.5.1 for Macintosh
• No driver support for UNIX
• No driver support for DOS applications
Features
ColorWise: Enables the X2 to independently adjust and correct any combination of RGB, CMYK, and Spot Color
data supplied to the X2 controller to provide accurate color rendition when printing with the 5765, 5790 and
DocuColor 5750/ 5799.
NetWise: This architecture supports Appletalk, TCP/IP (Ethernet/Token Ring), Native Novell 4.0 (NDS), Novell 3.x
(bindery), 10/100BaseT standard support, and Native Win 95 printing concurrently. Additionally, this architecture
allows the X2 to bind multiple frame types and protocols to the Ethernet or optional Token Ring card for auto
switching and detection.
PostScript 3: The Fiery X2 is a true Adobe PostScript 3 controller.
Upgrade Strategy
Currently there are no plans for upgrading.
Finishing Options
Sorter
• The Sorter is supported when STARR compression is enabled.
Terms and product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.
Post Launch Version 26 May 1999
Page 3 of 7 X2_Majestik_ced.doc
Loading...