Xerox FIB1 User Manual

Installation Instructions for FIB1- SERIAL RS-485/RS-423/RS-232 to Fiber Converter

Description

The FIB1-SERIAL will extend RS-485 transmission distance up to 2Km over multimode fiber or up to 120Km over single mode fiber. The converter is equipped with multiple interface circuits, for connection to RS-232, RS-423, or RS-485 (2 or 4-wire). The FIB1-SERIAL secures data transmissions at speeds up to 256kbps for RS-232, or up to 1024kbps for RS-422/485.

Specifications

Optical

Wavelength: 850, 1310 or 1550nm Optical Mode: Single Mode(S/M), or Multimode(M/M) Operating Distance: 2Km over multimode fiber

or up to 120Km over single mode fiber Fiber Type: 50/125um, 60/125um for M/M ; 9/125um for S/M Power Margin: 11dB(2Km, M/M), 12dB ~ 35dB(15 ~ 120Km, S/M) Data Rate: 31.104Mbps Line Coding: Scrambled NRZ Bit Error Rate: Less than 10

-11

DC Jack

Fiber Connections

LEDs

screws terminal

Pin Definition

Stickers

Front Panel Serial Port Definition & DIP Switch Setting

66--screws terminal

DIP Switch

Connectors Specifications

Optical: ST/SC type or WDM type (SC) Data: 6-Position detachable screw terminal

DATA SIGNAL Specifications

Data Formats: RS-485/422 2-Wire

RS-485/422 4-Wire

RS-232 + RTS/CTS 5-Wire

RS-232 3-Wire

RS-423 + RTS/CTS 5-Wire

RS-423 3-Wire

TTL 3-Wire Baud Rate: RS-485/422 up to 1024kbps

RS-232/423 up to 256kbps

TTL up to 1024kbps

LED Indicators

LED

Power Power indicator On Converter has power

Fiber Link Fiber link On The fiber link is up

Test Mode display On Any loopback test is on Data In Mode display On Serial transmission or receiving all zeros

Function

State

Off Converter has no power Blinking No SNMP is installed in FRM301

Off No signal or fiber link is down Blinking Remote side fiber Sync loss

Off Normal status

Off No Serial transmission or receiving all Blinking Receiving random serial data

Status

(space) data ones (mark) data

V.: 1.3

Six-screws Terminal Block

Application

FIB1-SERIAL Pin Assignment (DB9 Connector for Option)

Fiber Optic Connectors

Two connectors are provided for fiber optic cable connection. One is for transmission and the other is for reception of optical data. (WDM transceiver has only on SC connector for bi-directional transmissions on a single fiber)

Environment

Temperature : 0℃ -50℃(operating)

-20℃- 70℃ (storage)

Humidity 10-90% non condensing

Dimension

138mm x 86mm x 20mm

(H x W x D)

Power

+12V / 1A maximum DC plug type : center Positive

Weight : 300g

NO #

DB9

Female

9 72

3 4 5 6

TRADEMARKS Ethernet is a registered trademark of Xerox Corp.

is a registered trademark of AT&T.

WARNING:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate ra dio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference in which case the user will be required to correct the interferen ce at his own expense. NOTICE: (1) The changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. (2) Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.

CISPR PUB.22 Class A COMPLIANCE:

This device complies with EMC directive of the European Community and meets or exceeds the following technical standard. EN 55022 - Limits and Methods of Measurement of Radio Interference Characteristics of Information Technology Equipment. This device complies with CISPR Class A.

WARNING:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

CE NOTICE

Marking by the symbol CE indicates compliance of this equipment to the EMC directive of the European Community. Such marking is indicative that this equipment meets or exceeds the following technical standards: EN 55022:1994/A1:1995/A2:1997 Class A and EN61000-3-2:1995, EN61000-3-3:1995 and EN50082-1:1997

2 8 3 5