Xerox 2314 User Manual

11Mbps Wireless Internet Broadband Router

ANSEL 2314

Wireless BroadBand Router

User Guide

Version 1.3

0

11Mbps Wireless Internet Broadband Router

The information in this guide may change without notice. The manufacturer assumes

no responsibility for any errors which may appear in this guide.

Fast Ethernet is a trademark of XEROX Corporation. Microsoft, Windows and Windows

logo are trademarks of Microsoft Corporation.

Copyright 2002. All right reserved. No Part of the contents of this guide maybe

transmitted or reproduced in any form or by any means without the written permission

of the manufacturer. Printed in Taiwan.

th

The revision date for this guide is DEC 10

Version 1.3

FCC Certifications

, 2002

You are cautioned that any changes or modifications not expressly approved in this

manual could void your authorization to use the device.

CAUTION: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

Prohibition of co-location

This device must not be co-located or operating in conjunction with any other antenna

or transmitter.

15.105 Federal Communications Commission (FCC) Requirements, Part 15

This equipment has been tested and found to comply with the limits for a class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the

following measures:

---Reorient or relocate the receiving antenna.

---Increase the separation between the equipment and receiver.

---Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

---Consult the dealer or an experienced radio/TV technician for help.

1

11Mbps Wireless Internet Broadband Router

Regulatory information / Disclaimers

Installation and use of this Wireless LAN device must be in strict accordance with the

instructions included in the user documentation provided with the product. Any

changes or modifications (including the antennas) made to this device that are not

expressly approved by the manufacturer may void the user’s authority to operate the

equipment. The manufacturer is not responsible for any radio or television interference

caused by unauthorized modification of this device, or the substitution of the

connecting cables and equipment other than manufacturer specified. It is the

responsibility of the user to correct any interference caused by such unauthorized

modification, substitution or attachment. Manufacturer and its authorized resellers or

distributors will assume no liability for any damage or violation of government

regulations arising from failing to comply with these guidelines.

CAUTION: To maintain compliance with FCC’s RF exposure guidelines, this

equipment should be installed and operated with minimum distance 20 cm between

the radiator and your body. Use on the supplied antenna. Unauthorized antenna,

modification, or attachments could damage the transmitter and may violate FCC

regulations.

MPE Statement (Safety Information)

Your device contains a low power transmitter. When device is transmitted it sends out

Radio Frequency (RF) signal.

Safety Information

In order to maintain compliance with the FCC RF exposure guidelines, this equipment

should be installed and operated with minimum distance 20 cm between the radiator

and your body. Use only with supplied antenna. Unauthorized antenna, modification, or

attachments could damage the transmitter and may violate FCC regulations.

2

11Mbps Wireless Internet Broadband Router

Caution Statement of the FCC Radio Frequency Exposure

This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65C and

found compliant to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093,

and 15.247(b)(4) addressing RF Exposure from radio frequency devices. The radiation

output power of this Wireless LAN device is far below the FCC radio frequency

exposure limits. Nevertheless, this device shall be used in such a manner that the

potential for human contact during normal operation—as a mobile or portable device

but use in a body-worn way is strictly prohibit. When using this device, a certain

separation distance between antenna and nearby persons has to be kept to ensure RF

exposure compliance. In order to comply with the RF exposure limits established in the

ANSI C95.1 standards, the distance between the antennas and the user should not be

less than 20 cm.

CE Mark Warning

This is a Class B product. In a domestic environment, this product may cause radio

interference in which case the user may be required to take adequate measures.

3

11Mbps Wireless Internet Broadband Router

1: Introduction

1.1 Before You Start

1.2 System Requirement

1.3 How to Use this Guide

2: Hardware Installation

2.1 Product Description

2.1.1 Overview

2.1.2 Features

2.1.3 Front Panel

2.1.4 LEDs and Reset Button

2.1.5 Rear Panel

2.2 Installing the Router

2.2.1 Preparing for the installation

Contents

2.2.2 Getting Started

3: Configuration

3.1 Configuring the Wireless Access Point Router

3.2 The Setup Wizard

3.2.1 PPPoE Connection for WAN

3.2.2 Fixed IP for WAN

3.2.3 PPTP For WAN

3.2.4 Dynamic IP for WAN

3.2.5 Alias IP Setup

3.2.6 DNS

3.2.7 Wireless Configuration

3.2.8 Time Zone

3.3 Browsing the Status

3.3.1 Status

3.3.2 Wireless Status

3.3.3 DHCP Table

3.3.4 Routing Table

3.3.5 DDNS Status screen

3.4 Viewing the Tools

3.4.1 System Log

3.4.2 Hacker Log

3.4.3 Reset

3.4.4 Upgrade

4

11Mbps Wireless Internet Broadband Router

3.4.5 Backup

3.5 Setup the Advanced Features

3.5.1 LAN IP Setting

3.5.2 DHCP Setting

3.5.3 Firewall Setting

3.5.4 Privilege

3.5.5 Virtual Servers

3.5.6 Routing

3.5.7 WAN MAC Address Clone

3.5.8 DDNS Setting

3.5.9 MAC Control

3.6 Configuring your PCs to Connect to the Router

4: Specifications

4.1 Technical Specifications

4.2 Environmental Information

4.3 Standard Conformance

4.4 Cable Specifications

Appendix

A: About Static and Dynamic IP Address

B: Warranty Statement

5

11Mbps Wireless Internet Broadband Router

1: Introduction

The Wireless Internet Broadband Router combines the technology of Fast Ethernet

and IEEE 802.11b Wireless LAN, providing the home or small office users the

Cable/DSL access to the Internet via cord and cordless connection. At the same time,

integrated with the firewall and 128-bit WEP (Wired Equivalent Privacy) Encryption, the

Wireless Internet Broadband Router allows multiple users to share one Internet

connection while ensuring the safety and security of the packet flow.

Throughout this guide, the Wireless Internet Broadband Router may be referred to

as the Router.

1.1 Before You Start

Check the package of the router before you start. The package contents come with:

 One Wireless Access Point Router

 One AC/DC Power Adapter

 CD

 User Guide

1.2 System Requirement

Before you getting started, make sure you meet the following requirements.

 One RJ-45 Cable/DSL network connection

 One PC with installed 10/100 Mbps Ethernet Adapter

 UTP network cable with RJ-45 connector

 Windows 95/98/2000 or Windows NT for the Web-based Configuration

 Either Microsoft Internet Explorer 4.0 (or above version) or Netscape Navigator 4.0

(or above version)

For Wireless Connection

 One PC with installed Wireless Network Adapter

6

11Mbps Wireless Internet Broadband Router

1.3 How to Use this Guide

This guide is structured as follows:

 Chapter 2, Hardware Installation explains the function of the router and how to

physically install it.

 Chapter 3, Configuration explains how to set up and modify the configuration of

the router with its Web-based utility. In addition, the configuration of the PCs that

you want to connect to the Router can be found within this chapter.

 Chapter 4, Specifications contains information about the cables, environment and

the technical specifications of the router.

 Appendices include the information of Static IP address and Dynamic IP address,

comparison table and warranty Statement. Read them as necessary.

7

11Mbps Wireless Internet Broadband Router

2: Hardware Installation

2.1 Product Description

This chapter describes the features and functions of the router and shows how to

physically install it.

2.1.1 Overview

As the interface between WAN and LAN, the Wireless Internet Broadband Router

combines the technology of Fast Ethernet and IEEE 802.11b Wireless LAN, providing

the home and small office users the broadband access to the internet via cord and

cordless connection. Meanwhile with the integration-the firewall and 128-bit WEP

(Wired Encrypted Privacy) Encryption, the Wireless Internet Broadband Router allows

multiple users to share one Internet connection while ensuring the safety and security

of the packet flow. Also, the design of one antenna will enhance the reception of signals

transmitting from wireless adapters.

Strictly compliant with IEEE 802.11b, the Wireless Internet Broadband Router features

the transmission rate up to 11 Mbps and 2.4 GHz frequency band, easily building up

the wireless communication with other Wireless LAN devices. The local users' IP

address masking and specific port blocking offer two levels of security. Also, the

Wireless Internet Broadband Router serves as a DHCP server that automatically

assigns IP address to the devices on your local area network (LAN).

2.1.2 Features

 Interoperable with IEEE 802.11b (DSSS) 2.4GHz compliant equipment

 Transmission speeds adjustable at 1, 2, 5.5, and 11 Mbps.

 Features 2.4 GHz frequency band.

 Capable of up to 128-bit WEP (Wired Equivalent Privacy) Encryption secures the

network connection.

 MAC address filtering

 Supports PPPoE, PPTP Client, and Dynamic DNS

 Connects to a Cable/DSL modem or to an Ethernet backbone

 Equipped with a 4-port 10/100 Mbps Switch

 Creates a firewall to protect your PCs from outside intruders

 Configurable through any networked PC’s web browser

 Speeds up the gaming and multimedia connections dramatically

 Simultaneously act as either a DHCP server on the LAN or a DHCP client on the

8

11Mbps Wireless Internet Broadband Router

WAN

 Enables outside users to access the internal IP servers via Internet. Compatible

with virtually all standard Internet applications

 Compatible with all standard internet application

 Enables administrators to block specific interior users’ Internet access

2.1.3 Front Panel

The front panel of the router has 3 LEDs for each 10/100 Mbps ports, and three Module

Status LEDs at the left. The Internet LEDs are at the right. Figure 2-1 show front panels

of these routers.

Figure 2-1 Front panel of Wireless Access Point Routers with One Optional PCMCIA

Card, One Fixed Antenna, and One Reverse TNC Antenna

WLAN Status LED

10/100 Port Status LEDs

Internet Status LEDs

2.1.4 LEDs and Reset Button

The LEDs are explained in the following tables.

Table 2-1 WAN Status LED Functionality

LED Color Function

WLAN Act

WLAN Link

Green

Green

Lights to indicate the router is activated.

Lights to indicate that the Router’s wireless functions

have been enabled through the Web-based utility.

Power

Green

Lights to indicate the router has power.

9

11Mbps Wireless Internet Broadband Router

Table 2-2 10/100 Port Status LED Functionality

LED Color Function

Lights to indicate a functional network link through the

Link/Act

FULL/COL

Green

Green

100

LED Color Function

Link

Orange

Green

corresponding port with an attached device.

Blinks to indicate that the router is actively sending or

receiving data over that port.

Lights to indicate that the connection made through

the corresponding port is running in Full Duplex mode.

Blinks periodically to indicate that the connection is

experiencing collisions.

Lights for any port to indicate that the port is operating

at 100 Mbps.

Off to indicate that the port is operating at 10 Mbps

while the network is still operating.

Table 2-3 Internet LED Functionality

Lights to indicate a successful connection between

the Router and your broadband device or network.

Act

Diag

Green

Red

Blinks to indicate that the Router is sending or

receiving data over the broadband (Internet) port.

Lights to indicate the Router’s self-diagnosis mode is

running during boot-up and restart. It will turn off when

completing the diagnosis.

10

11Mbps Wireless Internet Broadband Router

2.1.5 Rear Panel

The rear panel of the router has one Reset button at the left. At the right area are the

Internet and LAN ports and a power connector. Figure 2-2 shows rear panels of these

routers. Table 2-4 explains the function of the port.

Figure 2-2 Rear panel of the Wireless Internet Broadband Router with

Fixed Antenna and one Reverse SMA Antenna

Reset Button Internet & LAN Ports DC Input Port

Table 2-4 All Port Functionality

Port Function

Reset

LAN port

Internet port

DC Input Port

Caution: Reset Button

Pressing the Reset button for more than 3 seconds while the router powers up will

restore to factory default setting. Note that this should be done only when you had tried

all the troubleshooting options. Pressing the Reset button during operation may bring

you into the risk of creating IP address conflict between your PC and the router. In such

Pressing the Reset button for more than 3 seconds to

restore to the factory default setting.

This is where you connect to the PC.

This is where you connect to the Cable/DSL modem.

To connect the adapter to receive power.

a case, you may be compelled to reboot your entire system(s).

11

11Mbps Wireless Internet Broadband Router

2.2 Installing the Router

This section will discuss what you should do before connecting your router to the

network and how to physically install it.

2.2.1 Preparing for Installation

Before you start to connect your router to any network device, make sure you get the

following values from your ISP. You will need those values to setup the Router and

configure you networked PCs to accept the IP address the Router chooses to assign

them.

 PPPoE User Name and Password

or

 Fixed Internet IP Address assigned by your local ISP

 Your Subnet Mask

 Your Default Gateway

 Your Primary DNS IP address

or

 Other values may be needed for Cable Modem users, please confirm with your

ISP

You are supposed to have all those information mentioned above from your ISP. If not,

contact your ISP and they will be able to supply all the information you need.

12

11Mbps Wireless Internet Broadband Router

2.2.2 Getting Started

You may complete the following steps to install your Wireless Internet Broadband

Router when you have all the information mentioned above on hand.

Step 1. Power all devices down. This should include your PCs, Cable or DSL modem

and the Router.

Step 2. Connect the Router to your PCs.

A. Connect one end of a standard network cable to the 10/100 RJ-45 LAN ports

on the back of the Wireless Access Point Router.

B. Connect the other end of the cable to the PC.

Step 3. Connect the Router to your Cable or DSL modem.

A. Connect one end of a standard network cable to the RJ-45 WAN port on the

back of the Wireless Access Point Router.

B. Connect the other end of the cable to either a Cable or DSL modem

Step 4. Supply the power to the Router.

A. Connect one end of the power cable to the Wireless Access Point Router.

B. Connect the power cube end of the power cable to a standard wall outlet.

When the Router receives power, the Power LED should remain solid Green.

Step 5. Supply the power to either your Cable or DSL modem.

Step 6. Press the Reset button to restore the Wireless Access Point Router‘s default

settings. Hold the button in for three seconds, or until the Diag LED illuminates

red.

13

11Mbps Wireless Internet Broadband Router

3: Configuration

3.1 Configuring the Wireless Access Point Router

Once you’ve done with the hardware installation, you may start to configure your

system. Note that this high-speed Wireless Router has an internal integrated-circuit

chip that programs all the administrative utility. The utility can be accessed by any PC

on the network at http://192.168.1.1 .

Typing http://192.168.1.1 into the PC’s browser address windows. (See Figure 3-1)

Then, you will receive a pop-up password request page. (See Figure 3-2) Type

“admin” into the Password field and leave the User Name field empty.

After you access the Utility, you can find detailed instructions and explanations by

clicking each page’s Help button. To apply any settings you’ve altered on any page,

click the Apply button, and then click Continue. To clear any values you’ve entered on

any page, click Cancel.

Figure 3-1 Http://192.168.1.1

Figure 3-2 A Password Request Page

14

11Mbps Wireless Internet Broadband Router

Note: If you have completed the basic configuration of the router, you may refer to

Section 3.6 Configuring your PCs to Connect to the Router to configure the PCs that

you plan to connect to the Router.

3.2 The Setup Wizard

Figure 3-3 shows the page that you will see once you have accessed to the Utility. The

Setup Wizard of the router will lead you step by step to configure your Router. Please

follow the instructions as the Wizard page request and change the settings in

accordance to the information provided by your ISP.

If you use ADSL modem to make Cable/DSL access, please go to 3.2.1 PPPoE

Connection for WAN. If the fixed IP is used, please go to 3.2.2 Fixed IP for WAN. As for

the Cable modem, please go to 3.2.4 Dynamic IP for WAN.

15