Xerox 016-2046-00, 016-2044-00, 016-2040-00, 016-2047-00, 016-2043-00 User Manual

...
Specifications
Material Safety Data Sheet for ColorStix® 8200 Ink Sticks
SECTION 1- PRODUCT IDENTIFICATION
Trade NamesXerox Part No.
Product Use: XEROX Phaser
SECTION 2 - INFORMATION ON INGREDIENTS
Xerox Phaser and fatty amide waxes, resins, and dyes. The specific identity of ingredients is withheld as a trade secret.
SECTION 3 - HAZARDS IDENTIFICATION
ROUTES OF EXPOSURE: Skin POTENTIAL HEALTH EFFECTS Immediate Effects: None are known, when used as intended in Phaser Color Printers. See Section 11 for toxicology test information. Chronic Effects: None are known SIGNS AND SYMPTOMS OF EXPOSURE: None are known. MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: None are known.
®
8200 Ink Sticks, Black016-2044-00, 016-2040-00
®
8200 Ink Sticks, Cyan016-2045-00, 016-2041-00
®
8200 Ink Sticks, Magenta 016-2046-00, 016-2042-00
®
8200 Ink Sticks, Yellow016-2047-00, 016-2043-00
®
8200 color printers
®
ColorStix®8200 Inks are a proprietary blend of polyethylene
®
8200 solid inks are considered articles under Hazard
®
8200
Specifications
SECTION 4 - FIRST AID MEASURES
EYES: Contact unlikely. If particles get into eyes, flush thoroughly with water. INGESTION: Not applicable INHALATION: Not applicable SKIN: Wash skin thoroughly with soap and water
SECTION 5 - FIRE FIGHTING MEASURES
FLASH POINT: > 221 degrees C (>429 degrees F), Pensky-Martens closed tester FIRE & EXPLOSION HAZARDS: These inks will burn. During a fire, irritating and toxic gases may be generated by thermal decomposition or combustion. EXTINGUISHING MEDIA: All extinguishing agents classified as B and C are effective, including dry powder(s), carbon dioxide, and halon. FIRE FIGHTING INSTRUCTIONS: Avoid inhalation of smoke. As in any fire,
User Guide 77
wear self-contained breathing apparatus, pressure demand, MSHA/NIOSH approved, and full protective gear.
SECTION 6 - ACCIDENTAL RELEASE MEASURES
SPILL OR LEAK: Not applicable
SECTION 7 - HANDLING AND STORAGE
HANDLING: No special precautions, when used as intended. STORAGE: Avoid high temperatures. Keep ink below 60 degrees C (140 degrees F)
SECTION 8 - EXPOSURE CONTROL - PERSONAL PROTECTION
EXPOSURE GUIDELINES: None established. ENGINEERING CONTROLS/PERSONAL PROTECTION: No special personal protection indicated, when used as intended.
SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE/ODOR: Waxy solid. Black, blue, red, or yellow in color/Faint odor SOLUBILITY IN WATER: Insoluble MELTING POINT: Approximately 100 degrees C (212 degrees F) SPECIFIC GRAVITY (Water = 1): Approximately 1, @ 25 degrees C (77 degrees F)
SECTION 10 - STABILITY AND REACTIVITY
Specifications
STABILITY: Stable. CONDITIONS TO AVOID: Temperatures above 200 degrees C (392 degrees F) INCOMPATIBILITY WITH OTHER MATERIALS: None HAZARDOUS POLYMERIZATION: Will not occur HAZARDOUS DECOMPOSITION PRODUCTS: Material may decompose into toxic byproducts when heated to temperatures above 200 degrees C (392 degrees F).
SECTION 11 - TOXICOLOGICAL INFORMATION
TOXICITY: Oral LD SKIN IRRITATION: Primary Dermal Irritation Index = 0.0; not skin irritants. CARCINOGENICITY: Components not listed by IARC, NTP, or OSHA.
SECTION 12 - ECOLOGICAL INFORMATION
No known impact
>5 g/kg (rats); practically non-toxic
50
78 Phaser® 8200 Color Printer
SECTION 13 - DISPOSAL CONSIDERATIONS
This product is not a hazardous waste as specified in 40CFR261. TCLP below hazardous waste levels set by EPA. State and local waste disposal requirements, however, may be more restrictive. Manage and dispose of waste in accordance with all federal, state, and local regulations.
SECTION 14 - TRANSPORT INFORMATION
DOT: Not regulated.
SECTION 15 - REGULATORY INFORMATION
TSCA: This material has been manufactured in compliance with the EPA Toxic Substances Control Act (TSCA). RCRA (Resource Conservation and Recovery Act): Not a hazardous waste as specified in 40CFR261. TCLP below hazardous waste levels set by EPA.
SECTION 16 - OTHER INFORMATION
Original preparation date: 11/27/01
Xerox Corporation Office Printing Business Environmental, Health & Safety P.O. Box 1000 Mail Stop 60-512 Wilsonville, Oregon 97070 Safety Information: 800-828-6571 Health Information: 716-422-2177
Specifications
Material Safety Data Sheet for Silicone Intermediate Transfer Layer Fluid
SECTION 1- PRODUCT IDENTIFICATION
Trade Name: Xerox Silicone Intermediate Transfer Layer Fluid, impregnated into printer's maintenance roller. Xerox part number 016-1933-00 (replacement standard capacity maintenance kit) Xerox part number 016-1932-00 (replacement extended capacity maintenance kit) Product Use: Xerox Phaser
SECTION 2 - INFORMATION ON INGREDIENTS
Xerox Silicone Intermediate Transfer Layer Fluid is a proprietary blend of silicone oils. Specific identities of components, and their percentage composition, are withheld as a trade secret.
User Guide 79
®
8200 color printers
SECTION 3 - HAZARDS IDENTIFICATION
ROUTES OF EXPOSURE: Skin, eyes POTENTIAL HEALTH EFFECTS: Health effects from this product are expected to be negligible, when product is used as intended in Xerox Phaser
®
8200 Color Printers. Immediate Effects: Inhalation: Not an expected route of entry Skin: May cause mild irritation. Eyes: May cause mild irritation. Ingestion: Not an expected route of exposure. Chronic Effects: None known or expected. SIGNS AND SYMPTOMS OF EXPOSURE Mild skin or eye irritation. MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE None known
SECTION 4 - FIRST AID MEASURES
INHALATION: Not a route of exposure for this product. EYES: Flush thoroughly with water. Seek medical attention if symptoms occur. SKIN: Wash thoroughly with soap and water. Seek medical attention if symptoms of irritation occur. INGESTION: Not a route of exposure for this product.
SECTION 5 - FIRE FIGHTING MEASURES
FLASH POINT: Flash point of fluid is 226 degrees C, Pensky-Martens closed-cup tester.
Specifications
EXTINGUISHING MEDIA: All extinguishing agents classified as B and C are effective, including dry powder(s), CO FIRE FIGHTING INSTRUCTIONS: As for any fire, wear self-contained
, and halon.
2
breathing apparatus, pressure demand, MSHA/NIOSH approved, and protective gear. FIRE AND EXPLOSION HAZARDS. During a fire, irritating and toxic substances may be generated by thermal decomposition or combustion. No unusual fire hazards expected.
SECTION 6 - ACCIDENTAL RELEASE MEASURES
SPILL OR LEAK: Fluid is impregnated into maintenance roller. Small amounts (ie., drops) may result from normal handling. Absorb and place in an appropriate disposal container. Clean spills thoroughly because residue can be slippery.
SECTION 7 - HANDLING AND STORAGE
HANDLING: Wash hands with soap and water after contact. Clean spills per SECTION 6. STORAGE: No special requirements.
80 Phaser® 8200 Color Printer
SECTION 8 - EXPOSURE CONTROL - PERSONAL PROTECTION
No special protection indicated when used as intended.
SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE: Clear liquid impregnated into maintenance roller. ODOR: Mild SOLUBILITY IN WATER: No data SPECIFIC GRAVITY: Specific gravity of fluid is 0.97 (water=1)
SECTION 10 - STABILITY AND REACTIVITY
STABILITY: Stable. INCOMPATIBILITY WITH OTHER MATERIALS: Strong oxidizing agents HAZARDOUS DECOMPOSITION PRODUCTS: At elevated temperatures, formaldehyde may be generated. HAZARDOUS POLYMERIZATION: Will not occur.
SECTION 11 - TOXICOLOGICAL INFORMATION
No toxicology data on mixture
SECTION 12 - ECOLOGICAL INFORMATION
Not available.
SECTION 13 - DISPOSAL CONSIDERATIONS
Fluid is not listed as RCRA hazardous waste. Dispose of in accordance with federal, state, and local regulations.
SECTION 14 - TRANSPORT INFORMATION
DOT: Not regulated.
SECTION 15 - REGULATORY INFORMATION
The following information pertains to the ingredients of Xerox Silicone Intermediate Transfer Layer Fluid:
TSCA (Toxic Substances Control Act): Listed in the TSCA inventory as verified by our suppliers. RCRA (Resource Conservation and Recovery Act): Not listed as RCRA hazardous wastes. The ingredients of this fluid are not listed as carcinogenic by OSHA, IARC or NTP.
Specifications
User Guide 81
SECTION 16 - OTHER INFORMATION
Original preparation date:11/27/01
Xerox Corporation Office Printing Business Environmental, Health & Safety P.O. Box 1000 Mail Stop 60-512 Wilsonville, Oregon 97070 Safety Information: 800-828-6571 Health Information: 716-422-2177
Material Safety Data Sheet for CleanTex® Alcopad
SECTION 1 – PRODUCT IDENTIFICATION
Trade NamesXerox Part No. Alcopad016-1845-00
Product identification numbers: 806B, 806C, 806H, 806T, 806Z, 806 Chemical name and synonyms: Isopropyl Alcohol Chemical formula: CH Emergency telephone numbers: CHEMTREC (Transportation): 1-800-424-9300 Product Use: Xerox Phaser
SECTION 2 – INFORMATION ON INGREDIENTS
Specifications
Component CAS# % OSHA PEL (ppm) ACGIL TLV (ppm) Isopropyl alcohol 67-63-0 91.0 400 400 Deionized water 7732-18-5 9.0 NA NA
CH(OH)CH
2
®
8200 Color Printer
3
SECTION 3 – HAZARDS IDENTIFICATION
Product is distributed as a single-use, presaturated pad, in which all the liquid is absorbed by the applicator. Isopropyl alcohol is a flammable liquid. Eye contact will cause local irritation and burning sensations with possible injury if not removed promptly. Repeated or prolonged contact with skin may produce irritation and cause dermatitis. Exposure above TLV may cause irritation of respiratory tract and eyes along with headaches, dizziness and CNS effects. May be harmful if swallowed. Carcinogenicity (OSHA/NTP/IARC/ACGIH): Not Listed. Medical Conditions Aggravated by Exposure: Not Listed.
SECTION 4 – FIRST AID MEASURES
EYE CONTACT: Flush with water for 15 minutes, including under eyelids. Get Medical help. SKIN CONTACT: Flush with water. INHALATION: Remove to fresh air. Keep at rest. Restore and/or support breathing as needed. Get prompt Medical attention. INGESTION: In the unlikely event of ingestion of a wiper, first aid measures should focus on removal of the object and preventing choking. Once removed,
82 Phaser® 8200 Color Printer
keep affected person at rest. Call physician immediately.
SECTION 5 – FIRE-FIGHTING MEASURES
FLASH POINT (TCC): 56 degrees F FLAMMABLE LIMITS (% BY VOLUME): LEL: NA UEL: NA AUTOIGNITION TEMPERATURE degrees F (degrees C): NA EXTINGUISHING MEDIA: Isopropyl-alcohol fires may be extinguished using carbon dioxide, dry chemical or alcohol foam. Water may be used to cool containers exposed to the fire. UNUSUAL FIRE OR EXPLOSION HAZARDS: Isopropyl alcohol may release vapors which may ignite at or above flash point. NFPA RATING: HEALTH (1) FLAMMABILITY (3) REACTIVITY (0) Formulation is classified as an OSHA Class IB Flammable Liquid NA = Not Available
SECTION 6 – ACCIDENTAL RELEASE MEASURES
Since the isopropyl-alcohol solution is completely absorbed by the applicator and the amount of isopropyl alcohol per applicator is small, the chance of a significant spill occurring is small. In the event however, that a significant amount of liquid is released, ventilate the area, especially low areas where vapors may collect, and remove all sources of ignition. Cleanup personnel need protection against liquid contact and vapor inhalation.
SECTION 7 – HANDLING AND STORAGE
Store in a clean, cool, ventilated area away from sources of ignition and oxidizing agents. Handle and store in a manner suitable for an OSHA class IB Flammable Liquid. Electrical services must meet applicable codes. Use non-sparking tools.
Specifications
SECTION 8 – EXPOSURE CONTROL – PERSONAL PROTECTION
Provide ventilation to maintain TLV. Use non-sparking tools. Avoid inhalation of vapors, contact with eyes and repeated or prolonged contact with skin. Do not take internally.
SECTION 9 – PHYSICAL AND CHEMICAL PROPERTIES
BOILING POINT (80 degrees C) (180 degrees F) % VOLATILE BY VOLUME @ 25 degrees C: 100 VAPOR PRESSURE (mmHg @ 25 degrees C): 33 EVAPORATION RATE (BUTYL ACETATE-1) >1 VAPOR DENSITY (AIR = 1): <1 FORM: liquid % SOLUBLE IN WATER @ 25 degrees C: 100 ODOR: alcohol SPECIFIC GRAVITY (G/CC @ 25 degrees C): 0.79 APPEARANCE OF LIQUID: clear
User Guide 83
SECTION 10 – STABILITY AND REACTIVITY
STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur. INCOMPATIBILITIES / CONDITIONS TO AVOID: Caustics, amines, alkanolamines, aldehydes, ammonia, strong oxidizing agents and chlorinated compounds. HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide
SECTION 11 – TOXICOLOGICAL INFORMATION
Not Available
SECTION 12 – ECOLOGICAL INFORMATION
Not Available.
SECTION 13 – DISPOSAL CONSIDERATIONS
Follow Federal, State and Local Regulations.
SECTION 14 – TRANSPORT INFORMATION
DOT CLASSIFICATION: Not Regulated. Proper Shipping Name: Hazard Class: UN Number: Packing Group: Hazard Labeling: IATA / ICAO CLASSIFICATION: Not Regulated.
Specifications
Proper Shipping Name: Hazard Class: UN Number: Packing Group: Hazard Labeling: IMDG CLASSIFICATION: Not Regulated. Proper Shipping Name: Hazard Class IMDG Page # Packing Group: Flash Point (degrees C): Marine Pollutant:
SECTION 15 – REGULATORY INFORMATION
SARA TITLE III REPORTING: Toxic Chemical (Section 313): Not Listed. Extremely Hazardous Substance: Not Listed. Section 302, 304, 311, 312) Hazard Class: Chronic Health: Yes Acute Health: Yes Fire Hazard: Yes Pressure Hazard: No
84 Phaser® 8200 Color Printer
Reactivity Hazard: No TSCA INVENTORY STATUS: All components listed are on the TSCA inventory.
SECTION 16 – OTHER INFORMATION
The information provided herein is compiled from internal reports and data from professional publications. It is furnished without warranty of any kind, expressed or implied. It is intended solely to assist in evaluating suitability and proper use of the material and in implementing safety precautions and procedures. Employees should use this information as a supplement to other information gathered by them and must make independent determination of suitability and completeness of information from all sources to assure proper use of these materials. All information used must be determined by the user to be in accordance with applicable federal, state and local laws and regulations. PREPARED BY:
CleanTex Products 33 Murray Hill Drive Nanuet, NY 10954 June 1997
Specifications
User Guide 85
Loading...