USER’S MANUAL
for
590 RB cycle
BUILT FOR HEALTH
SAFETY INSTRUCTIONS
To ensure the best safety of the exerciser, regularly
check it on damages and worn parts.
• If you pass on this exerciser to another person or if
you allow another person to use it, make sure that
that person is familiar with the content and
instructions in these instructions.
• Only one person should use the exerciser at a time.
• Before the first use and regularly make sure that all
screws, bolts and other joints are properly tightened
and firmly seated.
• Before you start your work-out, remove all
sharp-edged objects around the exerciser.
• Only use the exercise for your work-out if it works
flawlessly.
• Any broken, worn or defective part must immediately
be replaced and/or the exerciser must no longer be
used until it has been properly maintained and
repaired.
• Parents and other supervisory persons should be
aware of their responsibility, due to situations which
may arise for which the exerciser has not been
designed and which may occur due to children’s
natural play instinct and interest in experimenting.
• If you do allow children to use this exerciser, be sure
to take into consideration and assess their mental
and physical condition and development, and above
all their temperament. Children should use the
exerciser only under adult supervision and be
instructed on the correct and proper use of the
exerciser. The exerciser is not a toy.
• Make sure there is sufficient free space around the
exerciser when you set it up.
• To avoid possible accidents, do not allow children to
approach the exerciser without supervision, since
they may use it in a way for which it is not intended
due to their natural play instinct and interest in
experimenting.
• Please note that an improper and excessive
work-out may be harmful to your health.
• Please note that levers amd other adjustment
mechanisms are not projecting into the area of
movement during the work-out.
• When setting up the exerciser, please make
sure that the exerciser is standing in a stable
way and that any possible unevenness of the
floor is evened out.
• Always wear appropriate clothing and shoes
which are suitable for your work-out on the
exerciser. The clothes must be designed in a
way so that they will not get caught in any part of
the exerciser during the work-out due to their
form (for example, length). Be sure to wear
appropriate shoes which are suitable for the
work-out, firmly support the feet and which are
provided with a non-slip sole.
• Be sure to consult a physician before you start
any exercise program. He may give you proper
hints and advice with respect to the individual
intensity of stress for you as well as to your
work-out and sensible eating habits.
1
IMPORTANT NOTES
• Assemble the exerciser as per assembly instructions
and be sure to only use the structural parts provided
with the exerciser and designed for it. Prior to the
assembly, make sure the content of the delivery is
complete by referring to the parts list of the assembly
and operating instructions.
• Be sure to set up the exerciser in a dry and even place
and always protect it from humidity. If you wish to
protect the place particularly against pressure points,
contamination, etc., it is recommended to put a suitable,
non-slip mat under the exerciser.
• The general rule is that exercisers and training devices
are no toys. Therefore, they must only be used by
properly informed or instructed persons.
• Stop your work-out immediately in case of dizziness,
nausea, chest pain or any other physical symptoms. In
case of doubt, consult your physician immediately.
• Children, disabled and handicapped persons should
use the exercise only under supervision and in
presence of another person who may give support and
useful instructions.
• Be sure that your body parts and those of other
persons are never close to any moving parts of the
exerciser during its use.
• When adjusting the adjustable parts, make sure they
are adjusted properly and note the marked, maximum
adjusting position, for example of the saddle support,
respectively.
• Do not work out immediately after meals!
2
EXPLOSIVE DRAWING
3
84
14 23
24
83
6327 64
28
29
65
85
77
17 53 21
79
19
54
36
52
57
41
39R
37
38
51 6867
34
20R
39L
20L
611635
66
9
45L
12 11 31
2
55
8
45R
70
13
11
31
1
60 56
15
66
25
74
80
75
7
40
4
15
66
66
11
5
13
11
31
18
30
66
11
12
44
31
11
12
13
71 27
22
43
6
78
46
49
50 48
10
42
47
41
33
32
26
58
72
73
59
62
76
82
86
3
Picture of spare parts
D22xD8.5
D15.4xD8.2
M8x20L
13
11
31
M8x90L
M8x75L
M8x55L
M8x15L
D16x1.2T
M8*40L
x12
x4
x2
x2
x8
x16
x8
x20
x12
56
30
55
15
12
66
8
2
60
3
1
13
6
18
7
50
25
4
10
5
13
x1
x1
x1
x1
x1
x1
x1
x1
x1
x1
x1
x1
x1
x1
x1
x1
x1
4
Part List
part
no.
description
specifications
q'ty
1
Main frame
1 2 Front stabilizer
D60x1.5Tx390L
1
3
Rear stabilizer
1 4 Seat tube set
1 5 Handlebar set
1 6 Seat adjustable tube set
1
7
Seat support tube set
1 8 computer
UM-6636L2-7
1 9 Foot cap (round)
D60x71x101L
2
10
Handlebar post set
1
11
Spring washer
D15.4xD8.2x2T
20
12
Domed nut
M8x1.25x15L,8.8
8
13
Inner Allen bolt
M8x1.25x20L,8.8
12
14
Flywheel set
1
15
Inner Allen bolt
M8*1.25*40,8.8
8
16
Screw cover
D23x6.5
2
17
Plastic flat washer
D10*D24*0.4T
2
18
Seat
348*270*52,PAHS
1
19
Inner Allen bolt
M10*35L(8.8)
1
20L/R
Pedal
JD-22A 9/16"
1
21
Flat washer
D21*D8.5*1.5T
1
22
Round cross screw
ST4x20L
2
23
Anit-lose nut
3/8"-26UNFx6.5T
2
24
Magnetic fixing support
1
25
Back pad
410*340*57,PAHS
1
26
Tension cable
D1.2*230L
1
27
Spring
D1.2*55L
1
28
Allen bolt
M6*65L,8.8
1
29
Nylon nut
M6*1*6T
1
30
Square neck bolt
M8x1.25x90L,8.8
2
31
Curved washer
D22*D8.5*1.5T
12
32
Electric cable
100L
1
33
Sensor cable
100L
1
34
waved washer
D21xD16.2x0.3T
2
35
C-ring
S-16(1T)
1
36
Belt
374 PJ5
1
37
Pulley
D240x21
1
38
Round magnetic
M51
1
39L
Left crank
6 1/2"x9/16"-20UNF
1
39R
Right crank
6 1/2"x9/16"-20UNF
1
40
Ball pulling knob
D50xM16x32xD8
1
41
Upper computer cable
550L
1
42
Motor
1
43
Foot cap(twelve angles)
D75x50L
2
44
Buffer
D20*10L*M8*1.25
1
45L
Left chain cover
1
45R
Right chain cover
1
Loading...