© Xena Networks - 2017
1
XenaBay Chassis Installation Guide
HOW TO INSTALL XENA TEST MODULES
Version 2.8
Xena Networks ApS
Lottenborgvej 26, 2nd floor
2800 KGS Lyngby
Denmark
www.xenanetworks.com
© Xena Networks - 2017
2
SPECIFICATIONS
The XenaBay (C4-12) is a 12-slot, 4U heavy-duty steel rac k mount chassis designed to operate reliabl y in
industrial environments.
Form Factor:
Standard 4U, 19” wide
Construction:
Metal
Number of Slots:
12
Cooling:
3 x 8cm Papst 8412NH / NGLE, and
6 x 4cm Sunon MB40201VX-000U-A99 (on fanbar)
Drive Bay:
1 x 2.5” SATA Drive with Hotswap/ anti vibration.
• Dimensions (DxWxH): 483 x 177 x 447mm (19" x 7" x 17.6")
• Weight: 16.5 kg (36lbs) without test modules
• Color: Black
Environmental
• Operating Temperature: 10 to 35º C
• Storage Temperature: -30 to 70º C
• Humidity: 8% to 90% non-condensing
Power
• AC Voltage: 100-240 VAC
• Max watt: 1000W (100-114,9V) / 1200W (114,9-240V)
• Max. Noise 56 dBa.
Regulatory
• FCC (US)
• CE (Europe
TECH SUPPORT
Please contact your local Xena partner or send an email to support@xenanetworks.com.
PACKING LIST
When you unpack the chassis, make sure the following items have been shipped.
• 1 x XenaBay (C4-12) Chas s is
• 1 x Power cord
• 1 x Xena "Quick Start Guide"
• 1 x XenaBay Chassis Installation Guide
• 6 x 12v Power splitter cables
© Xena Networks - 2017
3
QUICK OVERVIEW
Installing test modules in the XenaBay C4-12 chassis requires the following steps to be completed.
NOTE: A slightly different procedure is needed for the M6SFP+, M6RJ45+/n and +25GE modules – see the
end of the document for instructions.
1. Remove the top cover by unscrewing the two bolts at the back of the chassis.
2. Unscrew the restraining bars that holds the module in place
3. Choose which slot the module should sit in and unscrew the bracket
4. Slide the module into place and use the screw to secure it*
5. Position the restraining bars in place.
6. Screw the restraining bars tightly in place.
For M6SFP+ and CFP cards - connect the power cable (see final section in this document)
* In August 2017 Xena improved the way test modules were mounted in the chassis by adding a plastic rail
attached with two screws to the test module. This rail ensures the test module is held very securely in place
when mounted in the chassis.
When transferring test modules with this plastic rail from a XenaBay purchased after August 2017 to an older
XenaBay, it is necessary to remove the plastic rail. This simply requires removing two screws.
7. Replace the top cover
The installation steps outlined above are described in detail below. Please refer to the relevant section.
IMPORTANT: ALWAYS REMOVE LONG TEST MODULES BEFORE SHIPPING
To minimize the risk of dam age, please rem ove “long” test modules bef ore transport ation. This inc ludes an y
test module(s) that extend past the metal restraining bar under the chassis lid.
Always use the original Xena boxes for shipping (including the polystyrene foam and anti-static bags).
© Xena Networks - 2017
4
STEP 1:
Remove the top cover by unscrewing the two bolts at the back of the chassis.
STEP 2:
Unscrew the fan bar and support bar that holds the modules in place.
The metal support bar holds test modules securely in place. This is very important during transport.
It is also used to mount the fans that cool the chassis. These are attached to the chassis by four screws
© Xena Networks - 2017
5
Loading...