XENA XZZ6L User Manual

For customer care

Email us at: [e-mail]

Repla cement batte ries and XENA a ccessories , please

visit: www.xenasecurity.com

Don’t fo rget to regis ter your XENA lo ck at
www.xenasecurity.com

Disclaimer:

XENA SECURITY ASSUMES NO RESPONSIBILITY OR LIABILITY
FOR DAMAGES OR INJURIES RESULTING FROM THE USE OR
MISUSE OF OUR PRODUCTS.

XENA JAPAN

USER MANUAL for
XZZ6L Series

Alarmed Disc-Locks

www.xenasecurity.com

PJ0706-1001-1133Copyright © XENA Security. All rights reserved

ENGLISH

XENA XZZ6L series di sc-lock alarm

Thank you for choosing a XENA Security product. By purchasing the world’s
strongest, smartest portable lock (with alarm inside), you’ve made life very dicult
for a would-be thief. Please read these instructions carefully. If you have any
questions or comments, don’t hesitate to email us at [e-mail].
For more information about this and other XENA products, accessories and
product news, visit www.xenasecurity.com.

Parts o f XZZ6L series a larmed disc-lock

1.

2.

3.

4.

1. Lock barrel

2. Locking pin

3. Reector

4. Flat coded key

5. Battery cover

6. Battery

7. Alarm module

8. Allen Key

9. Screw

1 2

5.

6.

7.

8.

9.

ENGLISH

Fitting XENA to your motor cycle’s brake disc

1. Requires brake-disc thickness less than 7mm (1/4”)

2. Locking-pin size: 6mm (1/4”)

3. Distance from locking-pin to back of disc-slot*: 42mm (1 5/8”)

Area for
locking pin

*Note that the locking pin can pass through ANY hole on the brake disc
(see dark areas on diagram).

The lock ing system

• Insert the key in the lock and rotate clockwise. The lock barrel will spring open.

• Slide the unit on to your motorcycle’s front or rear brake disc.

• Locate a hole in the brake disc that will allow the locking pin to pass through.

• Push the lock barrel down to insert the locking pin.

For more information on tting XENA locks to your bike,
go to www.xenasecurity.com/faqs.

ENGLISH

Your new XENA lock is shipped with the battery uninstalled. Please insert the CR2
battery supplied.

Batte ry installat ion (See g.B)

• Using Allen key provided (8), undo screw (8) located underneath lock.

• Remove module and battery cover.

• Insert CR2 3v Lithium Battery (IMPORTANT: ensure that + and - line up properly).

• Replace battery cover and insert module back into lock body immediately

• Dispose of used battery promptly.

Warning: When the alarm module is separated from the lock body the alarm

will activate. To avoid this please insert the module into the lock body
immediately after inserting the battery

Batte ry life

• Under normal use, batteries should last at least 8 months. Frequent triggering or

extreme temperatures can adversely aect battery life.

The alar m system

• There is no on-o switch. The unit automatically senses the presence of your brake disc.
(IMPORTANT: Ensure that reector is covered by brake-disc).

•

Your XENA alarmed disc-lock is self-arming. The alarm sensors will become active 5 seconds
after being locked on your brake-disc. The alarm will beep once to conrm that it is armed.

3 4

ENGLISH

B

To remove module

*For more product details, please check with your local XENA dealer or visit www xenasecurity.com

• 10 seconds after the arming beep, shock & motion sensors work independently to
determine if your bike is being tampered with.

Warning: Extremely loud alarm, avoid close proximity with ears.

Keys

• Each lock comes with three keys and a at coded key with serial number (ie,

X123456). Use this identication number to order keys for your lock. Make a note
of serial number and keep it in a safe place. It is recommended to register your
lock at www.xenasecurity.com