User Guide for OEM Integration
Model : FLR9G30
Brand : XAGYL COMMUNICATIONS
FLR9G30 is an Industrial grade 1000 mW Tx power mini-PCI radio module. It is
designed for the ISM frequency band 902 MHz ~ 928 MHz. It sports advanced
filtering and noise reduction design techniques for high interference immunity
from the neighboring Pager transmitters.
Applications
z Long Range Outdoor Broad band wireless applications
z Back hauls
z Access points & High Performance CPEs
z Mesh Wireless Infra structure applications
z Industrial applications
RADIO SYSTEM INFORMATION
Model No* FLR9G30
MAC and Baseband Athero s AR5414A
Interface 32bits, 33MHz m iniPCI Type III A
Operation Voltage 3.3V
Radio Frequency Band 902 MHz - 928 MHz
Data Rates 54, 48, 36, 24, 18, 12, 9, 6 Mbps (Auto fall back)
Channel Bandwidth 5, 10, or 20 MHz
Available Drivers Open Source MADWiFi for Linux, Windows 2000, XP and Vista
Tx/Rx Specification
5 MHz Channel BW (QUARTER RATE)
907 MHz, 912 MHz, 917 MHz & 922
MHz
Data Rate Modulation
Tx Power*
(± 1 dBm)
1.5 Mbps BPSK/COFDM 30 dBm -97 dBm
2.25 Mbps BPSK/COFDM 30 dBm -97 dBm
3 Mbps QPSK/COFDM 30 dBm -95 dBm
Rx Sensitivity
(± 2 dBm)
4.5 Mbps QPSK/COFDM 30 dBm -93dBm
6 Mbps 16QAM/COFDM
9 Mbps 16QAM/COFDM
12 Mbps 64QAM/COFDM
13.5 Mbps 64QAM/COFDM
30 dBm -90 dBm
29 dBm -86 dBm
28 dBm -81 dBm
27 dBm -78 dBm
Tx/Rx Specification
10 MHz Channel BW (HALF RATE)
907 MHz, 912 MHz, 917 MHz & 922
MHz
Data Rate Modulation
Tx Power*
(± 1 dBm)
3 Mbps BPSK/COFDM 30 dBm -95 dBm
4.5 Mbps BPSK/COFDM 30 dBm -95 dBm
6 Mbps QPSK/COFDM 30 dBm -93 dBm
Rx Sensitivity
(± 2 dBm)
9 Mbps QPSK/COFDM 30 dBm -91 dBm
12 Mbps 16QAM/COFDM
18 Mbps 16QAM/COFDM
24 Mbps 64QAM/COFDM
27 Mbps 64QAM/COFDM
30 dBm -88 dBm
29 dBm -84 dBm
28 dBm -79 dBm
27 dBm -76 dBm
Tx/Rx Specification
20 MHz Channel BW (FULL RATE)
912 MHz & 917 MHz
PHYSICAL, ENVIRONMENTAL AND OTHER SPECIFICATIONS
Antenna Ports* Two MMCX Ports
Data Rate Modulation
1 Mbps DBPSK/DSS 30 dBm -97 dBm
2 Mbps DQPSK/DSS 30 dBm -95 dBm
5.5 Mbps CCK/DSS 30 dBm -92 dBm
11 Mbps CCK/DSS 30 dBm -90 dBm
6 Mbps BPSK/COFDM 30 dBm -93 dBm
9 Mbps BPSK/COFDM 30 dBm -93 dBm
12 Mbps QPSK/COFDM 30 dBm -91 dBm
18 Mbps QPSK/COFDM 30 dBm -89 dBm
24 Mbps 16QAM/COFDM
36 Mbps 16QAM/COFDM
48 Mbps 64QAM/COFDM
54 Mbps 64QAM/COFDM
Tx Power*
(± 1 dBm)
30 dBm -86 dBm
29 dBm -82 dBm
28 dBm -77 dBm
27 dBm -74 dBm
Rx Sensitivity
(± 2 dBm)
Power Consumption Matrix
(@3.3V)
Max. Throughput test condition 1.5A (5W) 1.5A (5W) 1.5A (5W) 1.5A (5 W) 1.3A (4.3W)
Operating Temperature* -40°F to +185°F (-40°C to +85°C)
Dimension 2.36" x 2.63" (60 x 67 mm), approx. 0.04 lb (0.02 kg)
DBPSK/DSS BPSK/COFDM QPSK/COFDM 16QAM/COFDM 64QAM/COFDM
I
nterference Signal Desensitization Measurements
FLR9G30 Operating Freq = 917 MHz, 20 MHz Channel, BPSK/COFDM Modulation
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
o Reorient or relocate the receiving antenna.
o Increase the separation between the equipment and receiver.
o Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
o Consult the dealer or an experienced technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 2
not be co-located or operating in conjunction with any other antenna or
transmitter.
This device is intended only for OEM integrators under the following conditions:
1cm between the radiator & your body. This transmitter must
1. The antenna must be installed such that 2
antenna and users, and
2. The transmitter module may not be co-located with any other transmitter
or antenna,
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on
the final product. In these circumstances, the OEM integrator will be responsible
for re-evaluating the end product (including the transmitter) and obtaining a
separate FCC authorization.
IC Interference Statement
This device complies with RSS-210 of the IC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation. IC: 7503B-FLR9G30
1 cm is maintained between the
End Product Labeling
This transmitter module is authorized only for use in device where the antenna
may be installed such that 2
users. The final end product must be labeled in a visible area with the following:
“Contains FCC ID: XQBFLR9G30 & IC: 7503B-FLR9G30 ”.
1 cm may be maintained between the antenna and
Loading...