X-1 (H2O Audio) S8-1A3 User Manual

!

WARNING

!

H2O Audio stands behind our products.

Failure to follow our instructions could destroy

your iPod and will void the Warranty. If you

have any concerns, or experience any

difficulties with your H2O Audio product, we

are here to help you, so please contact us

directly. We can be reached at:

1.800.708.6080

[e-mail]

www.h2oaudio.com

S9-75 20070521

Important Note:

When closing the housing ensure the Silicone Sleeve is
slid all the way to the top of the Tray, with the Clip on
the outside of the housing. This is required to keep the
housing waterproof.

Do NOT slide Silicone Sleeve over the Clip located on the
back of the housing.

For more information please read your manual.

Correct

Incorrect

Important Note:

Apply a small amount of the enclosed Silicon Super O-Lube on
the Tray and on the inside of the Silicone Sleeve Seal Area. This
will help maintain a watertight seal, and facilitate the opening
and closing of the housing.

CAUTION:

If too many uses occur
between the application of the Super
O-Lube, a watertight seal cannot be
guaranteed. Please apply a small
amount of Super O-Lube at least

Apply Super O-Lube Here

If you have any questions or need refills, visit our website or contact
H2O Audio Customer Support
P. 858.623.0339
E. [e-mail]
h2oaudio.com

every 5 separations of the Tray and
Silicone Sleeve.

For more information please read
your manual.

Only use the lubricant provided.

www.h2oaudio.com

H2O Audio for iPod

shuffle (2nd Gen)

Printed Instructions

H2O Audio housings and cases are designed for specific Apple iPod models,
which vary by generation and storage size. You must ensure the correct
housing or case is purchased for your specific iPod model.

Before using this system, please be sure to read, understand, and follow the instruction of this manual.

2. Housing Features

TM

SealTight

®

Tray

Connector

Seal Area

Control Pad

Lanyard

3. Introduction

The H2O Audio waterproof housing allows you to listen to digital audio during
active watersports. This housing accomadates the Apple iPod shuffle 2
digital media player only.

HOUSING:

The housing features a Silicone Sleeve that intimately mates with the
hard plastic (polycarbonate) Tray. The housing allows for functional control of
the iPod shuffle 2

NOTE:

There is NO access to the power or shuffle switches on the iPod shuffle

nd

Gen when the waterproof housing is closed.

2

NOTE:

The shuffle is NOT waterproof without the H2O Audio housing and

nd

Gen control pad.

headphones, and is NOT covered under the product warranty. Any attempt
to use the housing with an audio player other than the Apple iPod shuffle

nd

Gen will void the Warranty.

2

HEADPHONES:

The housing is only waterproof when combined with H2O

Audio Waterproof Headphones (sold separately). Use of other headphones

nd

Gen

with a 3.5mm stereo connector will result in a water resistant case, and
should not be submerged.

4. Leak Test

Before utilizing the system for the first time, it is highly recommended to

Finger Grip

Clip

Silicone Sleeve

IMPORTANT: Make sure the top of the Tray mates tightly with the Seal Area

each time you close the housing. This is required to keep the housing
watertight. Remove any skins or covers from the shuffle player prior to use.

perform a 'Leak Test'. Follow the instructions below.

DO NOT INSTALL THE iPod shuffle 2nd Gen
INSIDE THE HOUSING FOR THE LEAK TEST

1. Open the housing (Section 5), and verify the seal area is clean and free of debris.

2. Close the housing (Section 7) and attach H2O Audio Waterproof Headphones.

3. Immerse the housing, (without the iPod shuffle 2

4. Manipulate the Control Pad during submersion.

5. Remove from the water, dry the exterior.

6. Open the housing.

NOTE:

When the Silicone Sleeve is separated from the Tray, water droplets

nd

Gen) in water and soak for 30 min.

will sometimes deposit on the side of the Tray. This does not indicate a leak,
it is a typical result when separating the housing.

5. Opening the Housing

Opening the housing is very technique sensitive, and we recommend you
practice opening and closing the housing a few times.

THE SILICONE SLEEVE IS NOT EASILY SEPARATED FROM THE TRAY.
THIS IS WHAT KEEPS YOUR IPOD SHUFFLE 2

Using one hand, secure the

1.

Lanyard. (at least 2 fingers
are recommended)

NOTE:

Grabing the Silicone Sleeve at the highest point possible on the Finger

Grips will help open the housing.

nd

Gen SAFE AND DRY.

Using your other hand, squeeze

2.

the Finger Grips of the Silicone
Sleeve at the Seal Area and pull
the Silicone Sleeve away from
the Tray.

6. Installing the iPod shuffle 2nd Gen into the Tray

Installing the iPod

The Tray that holds the iPod shuffle 2nd Gen is what protects your shuffle
from impact and water. It acts as an exoskeleton around your shuffle,
and provides support to the soft Silicone Sleeve of the housing.

Remove any skins or protective covers

1.

from your iPod shuffle 2

Slide the iPod shuffle 2nd Gen into the

2.

Tray (Control pad MUST be aligned
with the 5-hole pattern see 2.a ) and

line up the 3.5mm stereo plug of the Tray
with the 3.5mm stereo jack on the iPod

nd

shuffle 2

Push the iPod shuffle 2nd Gen all the way

3.

onto the stereo plug until the shuffle is

Gen.

seated completely within the Tray.

Turn on the iPod shuffle 2nd Gen before

4.

installing the Tray in the Silicon Sleeve.
There is no access to the power or shuffle
switchs once in the Silicon Sleeve.

Removing the iPod Shuffle 2

1.

Turn the Tray over to expose the back
with the Clip facing up. Using your
thumb to block the opening at the
bottom of the Tray will prevent the
shuffle from falling out once
disconected. Gently pushing the shuffle
down, unplugging it from the Tray and
slide out.

nd

Gen.

nd

2.a

3.

Gen

Tra y

shuffle

Clip

7. Closing the Housing

Make sure a small amount of “Super O-Lube” is present on the Tray and
the Silicone Sleeve before assembling them together. This will help
maintain a watertight seal, and facilitate the opening and closing of the
housing.

CAUTION:

If too many uses occur between the application of the Super O-Lube,
a watertight seal cannot be guaranteed. Please apply a small amount of
Super O-Lube at least every 5 separations of the Tray and Silicone Sleeve.

** For more Super O-Lube please contact H2O Audio’s Customers Support **

Make sure the shuffle is turned ON before closing the housing.

1.

There is no access to the power or shuffle Switchs when the housing is
closed.

2 3

Ensure the shuffle’s Control

2.

Pad and the Control Pad of
the Silicone Sleeve are both
aligned and facing up.

Inspect the Seal Area after closing to ensure that you have a tight seal

4.

between the Tray and the Silicone Sleeve. Ensure there are no gaps
between the Silicon Sleeve and Tray, they must be completely flush.
If you have any concerns, please repeat the Leak Test from Section 4.

Slide the Silicone Sleeve all the way

3.

to the top of the Tray, until it mates
tightly. Do NOT slide Silicone Sleeve

over the Clip located on the back
of the housing.

S8 - 70 20070713

8. Connecting the Headphones

The SealTightTM Connector (which is only featured on the H2O Audio
Waterproof Housing) is what keeps your audio connection safe and dry
underwater. It is designed specifically to create a seal around the H2O
Audio Series Waterproof Headphones (sold separately). Using any other
headphones will reduce the waterproof rating to water-resistant as the
headphone connection will not be completely waterproof.

To create a waterproof connection, align the 3.5mm stereo plug on the

1.

headphones with the stereo jack of the housing.

Insert the headphones into the stereo jack of the housing rotating the

2.

plug a quarter turn as you insert it into the jack, this will release any
air bubbles or pressure from the connection. Ensuring that the plug
mates securely into the SealTight

SV Series Headphones Connector

TM

Connector.

CAUTION: The SV Series Headphones do not fit
with the SealTight
featured only on the H2O Audio Series

TM

Connector boot Which is

housings. If your headphones have a connector
that looks like the one shown left, you can not
use them with this housing.

9. Control Pad

Previous / Rewind
Button

Play / Pause Button

Volume up

Next / Fast -

Forward Button

Volume down

10. Cliping the Housing to the Sport Armband

Clip the waterproof housing to the Sport Armband (included). It is
extreamly important that the Lanyard is used to secure the waterproof
housing to the Sport Armband. Running the armband strap though the
Lanyard will secure the housing to the armband.

11. FAQ

Why is the H2O Audio for iPod shuffle 2nd Gen so hard to open?

1.

While we want you to have access to your shuffle player, we do not
want water to have that same access. In our world, the more difficult is
to get into the case, the more reassured we are about its’ integrity.

My Lanyard broke, what can i do?

2.

While the Lanyard is not essential, it is very helpful. The Lanyard can
be replaced with any strong string, shoe lace or if you would like a
replacement Lanyard please to contact our Customer Support.

Do water droplets on the side of the Tray indicate a leak?

3.

No, this is a typical result when separating the Tray from the housing.
If you are concerned you can perform a Leak Test from Section 4.

NOTE: For more FAQ’s please visit www.h2oaudio.com

12. General Storage Procedures

For long-term storage, store in a plastic bag out of direct sunlight.

CAUTION: Do not expose the housing to extreme heat, such as the inside

of a hot car, or in hot direct sunlight, such as on a beach, or boat deck.
Doing so may cause damage and subsequent flooding.

CAUTION: The housing is susceptible to internal condensation with extreme

temperature fluctuations. Use above 105°F(40C) can result in internal
condensation. When used in temperatures below freezing, frost will
appear on the interior of the housing.

CAUTION: Do not store housing in the following environments:

* Solvents or other chemical fumes
* High humidity
* High Ozone
* Extreme temperature fluctuations

Storing the housing in these conditions may lead to a damaged housing,
causing it to leak.

Rinse the EXTERIOR of the system in fresh water after EACH use:

1. Make sure the housing is securely closed with headphones attached.

2. Soak in clean fresh water for 30 minutes.

3. Rinse the entire system with freshwater

4. Completely dry the entire exterior of the system using a clean soft
cloth.

Strong detergents, soaps, and chemicals MUST NEVER be used to clean
the system.

13. Available Accessories

H2O Audio Waterproof Headphones (required for use underwater)

Pro Armband for extreme sports

Swimbelt designed by swimmers

14. Contact Us

Customer Support is available Monday to Friday 9AM to 5PM PST.

www.h2oaudio.com
P. 800.708.6080 or 858.623.0339 x404 x403
F. 858.225.0815
E. [e-mail]

Copyright Notice:
This owner’s manual is copyrighted, all rights reserved. It may not, in whole or in part, be copied,
photocopied, reproduced, translated, or formed into any electronic format without prior consent in
writing. H2O Audio is a registered trademark of H2O Audio, Inc. Apple and iPod are registered
trademarks of Apple, Inc. Patents 6396769, 6614722, 6954405 Others Pending.

15. General Use Notice

READ THIS MANUAL CAREFULLY. IF YOU HAVE ANY QUESTIONS PLEASE CONTACT H2O
AUDIO CUSTOMER SUPPORT PRIOR TO USE.

IMPROPER USE OF THIS SYSTEM MAY CAUSE THE USER TO MAKE MISTAKES OR
DECISIONS THAT MAY LEAD TO SERIOUS INJURY OR DEATH.

IMPORTANT WARNING AND DISCLOSURE:
THOSE USERS THAT ELECT TO UTILIZE THIS SYSTEM AT, OR NEAR, THE WATER'S
SURFACE, MUST MAINTAIN SAFETY AWARENESS OF MOVING WATER CRAFTS.

ALWAYS MAKE SURE TO HAVE THE AUDIO PLAYER VOLUME TURNED TO ZERO AND
THE SPEAKERS AWAY FROM THE EARS WHEN TURNING ON THE H2O AUDIO UNIT. IF
THE VOLUME LEVEL IS NOT ZERO WHEN THE H2O AUDIO IS TURNED ON, IT MAY
CAUSE EAR INJURY DUE TO A SUDDEN BURST OF VOLUME. THE VOLUME SHOULD BE
SLOWLY INCREASED WITH AN AUDIO FILE PLAYING TO SET THE SPEAKER VOLUME TO
COMFORTABLE OUTPUT LEVELS PRIOR TO POSITIONING THE SPEAKERS NEXT TO THE
EARS.

IT CAN BE POTENTIALLY DANGEROUS TO PLAY YOUR HEADSETS WHILE ENGAGING IN
ACTIVITIES THAT REQUIRE YOUR FULL ATTENTION. YOU SHOULD EXERCISE EXTREME
CAUTION OR DISCONTINUE USE IN POTENTIALLY HAZARDOUS SITUATIONS. DO NOT
USE THE HEADPHONES WHILE DRIVING, CYCLING, OR OPERATING ANY MOTORIZED
VEHICLE. IT MAY CREATE A TRAFFIC HAZARD AND IS ILLEGAL IN SOME AREAS.

AVOID USING HEADPHONES AT HIGH VOLUME. HEARING EXPERTS ADVISE AGAINST
CONTINUOUSLY LOUD AND EXTENDED PLAY. IF YOU EXPERIENCE RINGING IN YOUR
EARS, REDUCE VOLUME OR DISCONTINUE USE.

THE MANUFACTURER DOES NOT WARRANT AND WILL NOT BE HELD RESPONSIBLE IN
ANY WAY FOR DAMAGES TO THE iPod, OR LOSS OF DATA, INCLUDING LOSS OF DATA
STORED IN THE iPod, RESULTING FROM AN EXCESSIVE IMPACT, THUNDER, OR AN
EORED ON YOUR DEVICE.

16. Warranty Coverage

H2O Audio guarantees, to the original purchaser only, that the equipment purchased
(EXCLUDING THE iPod ) is free of defects in material and/or under normal recreational use
for a period of one year (1) from date of consumer purchase from an Authorized Dealer;
provided that proper care and maintenance have been performed as prescribed by the
owner's guide included with the equipment. Should this product prove to be defective for
any reason (other than those listed as limitations below) the product will be serviced or
replaced at H2O Audio's sole discretion at no charge (excluding shipping and handling).
This warranty shall be void if the registration is not completed and sent to H2O Audio
Customer Services within 30 days of purchase. This warranty shall be void if the
equipment has been tampered with by anyone not authorized to perform service. The
warranty is non-transferable and extends to the original purchaser only and is valid only if
the equipment was purchased from an authorized dealer. Warranty does not extend to
cover damage from accident, abuse, tampering, lack of maintenance, theft, or loss. Service
or modifications by anyone other than an Authorized H2O Audio agent will void the
warranty. H2O Audio will not be responsible for recovery or replacement of the product in
the event of loss or theft. H2O Audio, its Authorized International Distributors, and
Authorized Dealers make no other warranties, either express or implied or orally, or in
writing, with respect to any other warranty coverage except those expressly stated within
the preceding sentences. H2O Audio will not be held responsible for any agreements orally
or in writing with the exception of those expressly included in this warranty statement. The
warranty registration card and the terms contained herein supersede all statements
contained in any and all owner's guides, instruction cards, or other equipment literature or
catalogs. In no event will H2O Audio, its Authorized International Distributors, and
Authorized Dealers be held responsible or liable for any personal injuries resulting from the
use of the covered equipment, or for any other damages, whether direct, indirect,
incidental, or consequential; even if H2O Audio has been advised of such damages.
Warranty does not extend to any damages that may occur to the iPod or loss of any data.

17. Returns

Prior to any return, a Return Authorization (RA) number must be obtained. To receive an
RA number, go online to www.h2oaudio.com/returns.php and follow the simple
instructions on how to return a product. Proof of purchase from an Authorized Dealer
will be required. A copy of the original sales receipt and a copy of the owner's portion of
the warranty card must accompany all correspondence regarding the equipment covered
by this warranty agreement or in direct reference to this warranty.

S6 - 70 20060210

S8 - 70 20070713