!
WARNING
!
H2O Audio stands behind our products.
Failure to follow our instructions could destroy
your iPod and will void the Warranty. If you
have any concerns, or experience any
difficulties with your H2O Audio product, we
are here to help you, so please contact us
directly. We can be reached at:
1.800.708.6080
support@h2oaudio.com
www.h2oaudio.com
Caution
Important Note:
When installing the iPod shuffle into
the housing you MUST ensure the
shuffle control pad is aligned with the
5-hole pattern on the Tray. see fig.1
12
When closing the housing you MUST
ensure the shuffle’s control pad and the
Control Pad of the Silicone Sleeve are
both aligned and facing up. see fig. 2
Read your manual
Caution
Important Note:
Apply a small amount of the enclosed Silicon Super O-Lube on
the Tray and on the inside of the Silicone Sleeve Seal Area. This
will help maintain a watertight seal, and facilitate the opening
and closing of the housing.
Apply Super O-Lube here
CAUTION: If too many uses occur between the application of
the Super O-Lube, a watertight seal cannot be guaranteed.
Please apply a small amount of Super O-Lube at least every 5
separations of the Tray and Silicone Sleeve. For more information
please read your manual.
If you have any questions or need refills, visit our website or contact
H2O Audio Customer Support
P. 858.623.0339
E. support@h2oaudio.com
h2oaudio.com
Only use the lubricant provided.
www.h2oaudio.com
H2O Audio for iPod shuffle
Before using this system, please be sure to read, understand, and follow the instruction of this manual.
®
Printed Instructions
2. Housing Features
TM
SealTight Connector
Tray
Seal Area
Finger Grip
Control Pad
Silicone Sleeve
IMPORTANT: Make sure the top of the Tray mates tightly with the Seal Area each time you close the
housing. This is required to keep the housing watertight. Remove any skins or covers from the shuffle
player prior to use.
Lanyard
3. Introduction
The H2O Audio waterproof housing lets you to listen to digital audio during
active watersports. It houses the Apple iPod shuffle digital media player.
HOUSING: The housing features a Silicone Sleeve that intimately mates with
the hard plastic (polycarbonate) Tray. The housing allows for functional control
of the iPod shuffle control pad.
NOTE: There is NO access to the slider control on the iPod shuffle
NOTE: The iPod shuffle is NOT waterproof without the H2O Audio housing
and headphones, and is NOT covered under the product warranty. Any
attempt to use the housing with an audio player other than the Apple iPod
shuffle will void the Warranty.
HEADPHONES: The housing is only waterproof when combined with H2O
Audio Waterproof Headphones (sold separately). Use of other headphones
with a 3.5mm stereo connector will result in a water resistant case, and should
not be submerged.
4. Leak Test
Before utilizing the system for the first time, it is highly recommended to
perform a 'Leak Test'. Follow the instructions below.
DO NOT INSTALL THE iPod shuffle INSIDE THE HOUSING FOR THE LEAK TEST
1. Open the housing (Section 5), and verify the seal area is clean and free
of debris.
2. Close the housing (Section 7) and attach H2O Audio Waterproof
Headphones.
3. Immerse the housing, (without the iPod shuffle) in water and soak for
30 minutes.
4. Manipulate the Control Pad during submersion.
5. Remove from the water, dry the exterior.
6. Open the housing.
NOTE:
When the Silicone Sleeve is separated from the Tray, water droplets will
sometimes deposit on the side of the Tray. This does not indicate a leak, it is a
typical result when separating the housing.
5. Opening the Housing
Opening the housing is very technique sensitive, and we recommend you
practice opening and closing the housing a few times.
THE SILICONE SLEEVE IS NOT EASILY SEPARATED FROM THE TRAY. THIS IS
WHAT KEEPS YOUR IPOD SHUFFLE SAFE AND DRY.
1
Using one hand, secure the
1.
Lanyard. (at least 2 fingers
are recommended)
NOTE:
Grabing the Silicone Sleeve at the highest point possible on the Finger
Grips will help open the housing.
2
Using your other hand, squeeze
2.
the Finger Grips of the Silicone
Sleeve at the Seal Area and pull
the Silicone Sleeve away from
the Tray.
6. Installing the iPod shuffle into the Tray
Installing the iPod
The Tray that holds the iPod shuffle is what
protects your shuffle form impact and water. It
acts as an exoskeleton around your shuffle,
and provides support to the soft Silicone
Sleeve of the housing.
Remove any skins or protective covers from
1.
your iPod shuffle.
Slide the iPod shuffle into the Tray
2.
(Control pad MUST be aligned with
the 5-hole pattern see 2.a ) and line up
the 3.5mm stereo plug of the Tray with
the 3.5mm stereo jack on the iPod
shuffle see 2.b.
Push the iPod shuffle all the way onto the
3.
stereoplug until the shuffle is seated
completely within the bottom catch of
the Tray.
Turn on the power on the iPod shuffle
4.
using the slider switch before putting the
Tray into the Silicone Sleeve.
2.a
2.b
Removing the iPod
To remove the shuffle player from the Tray, lightly press down on the
1.
player at the bottom of the slider swith through the back of the Tray.
While applying light pressure, slide the shuffle off the stero jack.
2.
if necessary pull down on the bottom of the tray to release
the player and slide the shuffle out.
7. Closing the Housing
Make sure there is a small amount of “Super O-Lube” present on the
Tray and the Silicone Sleeve before assembling them together. This will
help maintain a watertight seal, and facilitate the opening and closing of
the housing.
CAUTION: If too many uses occur between the application of the Super
O-Lube, a watertight seal cannot be guaranteed. Please apply a small
amount of Super O-Lube at least every 5 separations of the Tray and
Silicone Sleeve.
Make sure the iPod shuffle is turned ON before closing the housing.
1.
There is no access to the On/Off Switch (slider) when the housing is
closed.
3
2
Ensure the shuffle’s Control
2.
Pad and the Control Pad of
the Silicone Sleeve are both
aligned and facing up.
Inspect the Seal Area after closing to ensure that you have a tight seal
4.
between the Tray and the Silicone Sleeve. If you have any concerns,
please repeat the Leak Test from Section 4.
3
Slide the Silicone Sleeve all the way
3.
to the top of the Tray, until it mates
tightly with the Tray.
S6 - 70 20060210
8. Connecting the Headphones
The SealTight Connector is what keeps your audio connection safe and
dry underwater. It is designed specifically to create a seal around the
H2O Audio Series Waterproof Headphones (sold separately). Using any
other headphones will not have a complete waterproof connection, and
reduces the waterproof rating to water-resistant.
To create a waterproof connection, align the 3.5mm stereo plug on the
1.
headphones with the stereo jack of the housing.
Insert the headphones into the stereo jack of the housing, ensuring
2.
that the plug mates securely into the SealTight Connector.
CAUTION: The SV Series Headphones do not fit with the SealTight Connector boot
featured on the H2O Audio Series housings. If your headphones have a connector
that looks like the one shown below, you can not use them with this housing.
TM
TM
TM
SV Series Headphones Connector
9. Control Pad
Volume up
Play / Pause
Button
Next / Fast Forward Button
Previous / Rewind
Button
Volume down
10. FAQ
Why is the H2O Audio for iPod shuffle so hard to open?
1.
While we want you to have access to your shuffle player, we do not
want water to have that same access. In our world, the more difficult
it is to get into the case, the more reassured we are about its’ integrity.
My Lanyard broke, what can i do?
2.
While the Lanyard is not essential, it is very helpful. The Lanyard can
be replaced with any strong string, shoe lace or if you would like a
replacement Lanyard please to contact our Customer Support.
Do water droplets on the side of the Tray indicate a leak?
3.
No, this is a typical result when separating the Tray from the housing.
If you are concerned you can perform a Leak Test from Section 4.
NOTE: For more FAQ’s please visit www.h2oaudio.com
11. General Storage Procedures
For long-term storage, store in a plastic bag out of direct sunlight.
CAUTION: The life of a T-Seal is typically one (1) year. Contact H2O Audio
for spare T-Seals or a maintenance kit. Always remember to reinstall the
T-Seal before next use. Do not expose the housing to extreme heat, such
as the inside of a hot car, or in hot direct sunlight, such as on a beach, or
boat deck. Doing so may cause damage and subsequent flooding.
CAUTION: The housing is susceptible to internal condensation with
extreme temperature fluctuations. Use above 105°F(40C) can result in
internal condensation. When used in temperatures below freezing, frost
will appear on the interior of the housing.
CAUTION: Do not store housing in the following environments:
* Solvents or other chemical fumes
* High humidity
* High Ozone
* Extreme temperature fluctuations
Storing the housing in these conditions may lead to a damaged housing,
causing it to leak.
Rinse the EXTERIOR of the system in fresh water after EACH use:
1. Make sure the housing is securely closed with headphones attached.
2. Soak in clean fresh water for 30 minutes.
3. Rinse the entire system with freshwater
4. Completely dry the entire exterior of the system using a clean soft
cloth.
5. Dry face down so water can properly drain from the Commander
Scroll Wheel.
Strong detergents, soaps, and chemicals MUST NEVER be used to clean
the system.
TM
12. Available Accessories
H2O Audio Waterproof Headphones (required for use underwater)
Pro Armband for extreme sports
Swimbelt designed by swimmers
13. Contact Us
Customer Support is available Monday to Friday 9AM to 5PM PST.
www.h2oaudio.com
P. 800.708.6080 or 858.623.0339
F. 858.225.0815
E. support@h2oaudio.com
Copyright Notice:
This owner’s manual is copyrighted, all rights reserved. It may not, in whole or in part, be copied,
photocopied, reproduced, translated, or formed into any electronic format without prior consent in
writing. H2O Audio is a registered trademark of Diver Entertainment Systems, Inc. Apple and iPod
are registered trademarks of Apple Computer Inc.
Patents 6396769, 6614722, 6954405 Others Pending.
14. General Use Notice
READ THIS MANUAL CAREFULLY. IF YOU HAVE ANY QUESTIONS PLEASE CONTACT H2O
AUDIO CUSTOMER SUPPORT PRIOR TO USE.
IMPROPER USE OF THIS SYSTEM MAY CAUSE THE USER TO MAKE MISTAKES OR
DECISIONS THAT MAY LEAD TO SERIOUS INJURY OR DEATH.
IMPORTANT WARNING AND DISCLOSURE:
THOSE USERS THAT ELECT TO UTILIZE THIS SYSTEM AT, OR NEAR, THE WATER'S
SURFACE, MUST MAINTAIN SAFETY AWARENESS OF MOVING WATER CRAFTS.
ALWAYS MAKE SURE TO HAVE THE AUDIO PLAYER VOLUME TURNED TO ZERO AND
THE SPEAKERS AWAY FROM THE EARS WHEN TURNING ON THE H2O AUDIO UNIT. IF
THE VOLUME LEVEL IS NOT ZERO WHEN THE H2O AUDIO IS TURNED ON, IT MAY
CAUSE EAR INJURY DUE TO A SUDDEN BURST OF VOLUME. THE VOLUME SHOULD BE
SLOWLY INCREASED WITH AN AUDIO FILE PLAYING TO SET THE SPEAKER VOLUME TO
COMFORTABLE OUTPUT LEVELS PRIOR TO POSITIONING THE SPEAKERS NEXT TO THE
EARS.
IT CAN BE POTENTIALLY DANGEROUS TO PLAY YOUR HEADSETS WHILE ENGAGING IN
ACTIVITIES THAT REQUIRE YOUR FULL ATTENTION. YOU SHOULD EXERCISE EXTREME
CAUTION OR DISCONTINUE USE IN POTENTIALLY HAZARDOUS SITUATIONS. DO NOT
USE THE HEADPHONES WHILE DRIVING, CYCLING, OR OPERATING ANY MOTORIZED
VEHICLE. IT MAY CREATE A TRAFFIC HAZARD AND IS ILLEGAL IN SOME AREAS.
AVOID USING HEADPHONES AT HIGH VOLUME. HEARING EXPERTS ADVISE AGAINST
CONTINUOUSLY LOUD AND EXTENDED PLAY. IF YOU EXPERIENCE RINGING IN YOUR
EARS, REDUCE VOLUME OR DISCONTINUE USE.
THE MANUFACTURER DOES NOT WARRANT AND WILL NOT BE HELD RESPONSIBLE IN
ANY WAY FOR DAMAGES TO THE iPod, OR LOSS OF DATA, INCLUDING LOSS OF DATA
STORED IN THE iPod, RESULTING FROM AN EXCESSIVE IMPACT, THUNDER, OR AN
EORED ON YOUR DEVICE.
15. Warranty Coverage
H2O Audio guarantees, to the original purchaser only, that the equipment purchased
(EXCLUDING THE iPod ) is free of defects in material and/or under normal recreational use
for a period of one year (1) from date of consumer purchase from an Authorized Dealer;
provided that proper care and maintenance have been performed as prescribed by the
owner's guide included with the equipment. Should this product prove to be defective for
any reason (other than those listed as limitations below) the product will be serviced or
replaced at H2O Audio's sole discretion at no charge (excluding shipping and handling).
This warranty shall be void if the registration is not completed and sent to H2O Audio
Customer Services within 30 days of purchase. This warranty shall be void if the
equipment has been tampered with by anyone not authorized to perform service. The
warranty is non-transferable and extends to the original purchaser only and is valid only if
the equipment was purchased from an authorized dealer. Warranty does not extend to
cover damage from accident, abuse, tampering, lack of maintenance, theft, or loss. Service
or modifications by anyone other than an Authorized H2O Audio agent will void the
warranty. H2O Audio will not be responsible for recovery or replacement of the product in
the event of loss or theft. H2O Audio, its Authorized International Distributors, and
Authorized Dealers make no other warranties, either express or implied or orally, or in
writing, with respect to any other warranty coverage except those expressly stated within
the preceding sentences. H2O Audio will not be held responsible for any agreements orally
or in writing with the exception of those expressly included in this warranty statement. The
warranty registration card and the terms contained herein supersede all statements
contained in any and all owner's guides, instruction cards, or other equipment literature or
catalogs. In no event will H2O Audio, its Authorized International Distributors, and
Authorized Dealers be held responsible or liable for any personal injuries resulting from the
use of the covered equipment, or for any other damages, whether direct, indirect,
incidental, or consequential; even if H2O Audio has been advised of such damages.
Warranty does not extend to any damages that may occur to the iPod or loss of any data.
16. Returns
Prior to any return, a Return Authorization (RA) number must be obtained. To receive an
RA number, go online to www.h2oaudio.com/returns.php and follow the simple
instructions on how to return a product. Proof of purchase from an Authorized Dealer
will be required. A copy of the original sales receipt and a copy of the owner's portion of
the warranty card must accompany all correspondence regarding the equipment covered
by this warranty agreement or in direct reference to this warranty.
S6 - 70 20060210
Loading...