Your TV Buddy™ Universal TV Remote controls
most all TV brands presently available. It also
includes a handy bottle opener and corkscrew so
you can enjoy a beer or a glass of wine while
watching your favorite movie.
SET UP INSTRUCTIONS
Install 2 AAA alkaline batteries in the battery
compartment on the back of the remote.
Look up the 3 digit code for your brand of TV
from the Code Table and install it into the remote
as follows:
To enter Codes directly from Library Code
Table.
1. Press and hold the Power and Mute buttons
simultaneously until the red LED remains on.
2. Release the buttons.
3. Enter the 3 digit code for your brand of TV
from the Library Code Table by using the V-,
Ch+, and V+ buttons. Use the V- button to
enter the first digit, use the Ch+ button to
enter the second digit and use the V+ button
to enter the third digit.
E.G. to enter code 013, don’t press V-, press
Ch+ once, and press V+ three times. The red
LED blinks off with each keypress.
4. Press the Mute button to save the code.
Note: for a valid code, the red LED turns off.
For an invalid code, the red LED blinks
rapidly for three seconds before going off.
5. Direct code entry is now complete.
Write your code below in case you forget it.
32
Code Search Method
Code Identification
If you cannot find a 3 digit code in the Code
Table that operates your TV, try searching for the
code as follows:
1. Manually turn on the TV to be controlled.
2. Press and hold the Power and Mute buttons
until the red LED remains on.
3. Release the buttons.
4. Press the Power button to begin code search.
5. Press the Channel Up (Ch+) button (or Power
button) repeatedly until the TV changes
channel (or turns off). You might have to
press the button 100 times or more to find
your code. If you accidentally overshoot the
code required, press the Channel Down (Ch-)
button, to backtrack through the code library
until the TV changes channel.
6. Press Mute to save the code.
7. Code Search is now complete. Write down
your code on the previous page.
Note: Code Search will start from the currently
stored three digit number. E.G. if there are 100
codes in the library and the currently stored code
is 050 then the Code Search will start from 051
continuing to 100 before looping back to 000
and finishing at 050.
To determine the code installed in the remote:
1. Press and hold Power and Mute at the same time
until the red LED remains on.
2. Release the buttons.
3. Press and release the Channel Down (Ch-)
button. The red LED blinks off once to
indicate the keypress acceptance.
4. To find the first digit, press the V- button and
count the red LED blinks. To find the second
digit, press the Ch+ button and count the red
LED blinks. To find the third digit, press the
V+ button and count the red LED blinks. The
red LED remains off after the last blink.
Note: No blink indicates a “0” digit.
5. Code Identification is now complete.
Note: If the remote accidentally gets stuck down
the back of the couch with a button pressed it
will stop transmitting after about 2 minutes so as
not to drain the battery.
When changing batteries have the new batteries
handy before removing the old ones. If the
remote has no batteries installed for more than
about a minute you will lose the installed code.
54
OPERATION
Press Power to turn your TV on and off.
Press Channel Up (Ch+) or Channel Down (Ch-)
to change channels.
Press Volume Up (V+) and Volume Down (V-) to
adjust the volume of your TV.
Press Mute to silence your TV.
Place back of bottle opener over bottle top and
lift.
Screw corkscrew clockwise into top of wine
bottle and pull.
X10.COM A DIV. OF X10 WIRELESS TECHNOLOGY, INC. (X10)
WARRANTS ITS PRODUCTS TO BE FREE FROM DEFECTIVE
MATERIAL AND WORKMANSHIP FOR A PERIOD OF ONE (1) YEAR
FROM THE ORIGINAL DATE OF PURCHASE AT RETAIL. X10 AGREES
TO REPAIR OR REPLACE, AT ITS SOLE DISCRETION, A DEFECTIVE
X10 PRODUCT IF RETURNED TO X10 WITHIN THE WARRANTY
PERIOD AND WITH PROOF OF PURCHASE.
IF SERVICE IS REQUIRED UNDER THIS WARRANTY:
1. CALL 1-800-675-3044, OR VISIT WWW.X10.COM, OR E-MAIL
SALES@X10.COM TO OBTAIN A RETURN MERCHANDISE
AUTHORIZATION (RMA) NUMBER.
2. RETURN THE DEFECTIVE UNIT POSTAGE PREPAID TO THE
ADDRESS ON BACK.
3. ENCLOSE A CHECK FOR $4.00 TO COVER HANDLING AND
RETURN POSTAGE.
4. ENCLOSE A DATED PROOF OF PURCHASE.
5. X10 IS NOT RESPONSIBLE FOR SHIPPING DAMAGE. UNITS TO BE
RETURNED SHOULD BE PACKED CAREFULLY.
THIS WARRANTY DOES NOT EXTEND TO ANY X10 PRODUCTS
WHICH HAVE BEEN SUBJECT TO MISUSE, NEGLECT, ACCIDENT,
INCORRECT WIRING OR TO USE IN VIOLATION OF OPERATING
INSTRUCTIONS FURNISHED BY US, NOR EXTEND TO ANY UNITS
ALTERED OR REPAIRED FOR WARRANTY DEFECT BY ANYONE
OTHER THAN X10. THIS WARRANTY DOES NOT COVER ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES AND IS IN LIEU OF
ALL OTHER WARRANTIES EXPRESSED OR IMPLIED AND NO
REPRESENTATIVE OR PERSON IS AUTHORIZED TO ASSUME FOR US
ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF OUR
PRODUCTS.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS, AND/OR THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO
THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO
THE ORIGINAL CUSTOMER. THIS WARRANTY GIVES YOU SPECIFIC
RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
If you have any questions concerning warranty or installation, please call 1-800675-3044, e-mail sales@x10.com, or visit www.x10.com/warranty for on-line
warranty registration.
1514
X10.com, a division of
X10 Wireless Technology, Inc.
(Returns Depot),
3824 North 5th St., Suite C,
North Las Vegas, NV 89030
www.x10.com/support
BBR-9/01
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.