X10 CR15A User Manual

™

V anguard R emote

For use with VK77A Camera System

Model
CR15A

The CR15A Remote lets you move the position of a VK77A V anguard camera from left to right (Pan) and up and
down (Tilt) as well as Zoom in on the picture. Y ou can store 9 positions for a camera and then use the remote to sweep
between these positions. Install 4 AAA alkaline batteries (sold separately) in the remote’s battery compartment.

Operation

Press a left or right “arrow” button at the top of the
CR15A Remote to “Pan” the camera left or right. Press
an up or down “arrow” button to “Tilt” the camera up
or down. Press Zoom in and out. The camera auto­focuses but you can fine-tune the focus with the
manual focus Up/Down buttons.

Stored Positions

Y our Vanguard Camera can remember nine locations,
including vertical/horizontal positions, and zoom
settings.

Storing a Position

You can store up to nine positions in your camera.
Here’s how:

1. Press and release C1.

2. Press and hold the Setup button on your remote
control until the C1 button lights green.

3. Move the camera to the position you want to
store. Press Autofocus to set the focus for that
position.

4. Press the number button (1 through 9) on the
remote to store the position under that button.

5. Repeat steps 2 and 3 for each position you want to
store.

6. When finished, press Setup to save the positions
you entered.

Selecting Positions

Once you’ve stored positions in the camera, press the
desired number button on the remote to move to that
position. If you press Sweep, the camera will automati­cally switch through all the positions you’ve stored.
Press any of the movement buttons on the remote to

stop the camera from sweeping.

Changing Stored Positions

You can store new positions over positions you’ve
already stored, by following the instructions above.
Just store the new position using a button that you
programmed before.

Clearing Stored Positions

You can delete all stored positions. Here’s how:

1. Press and release C1.

2. Press and hold Setup until the C1 button lights
green.

3. Press Center.

4. Press Setup again.

Autofocus.
Pressing any of these

turns on that camera,
and turns the other 3
off (Transceiver
required). Not used if

you only have one
camera.

Zooms in.

The camera auto­focuses but you can
fine-tune the focus
manually, i.e., focus on
objects in the back­ground or foreground.
Focus Up focuses on
faraway objects. Focus
Down focuses on near
objects.

Used to store camera
positions and for other
setup functions.

F .C.C. CAUTION - THIS DEVICE COMPLIES WITH P AR T 15 OF THE
FCC RULES. OPERA TION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MA Y NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THA T
MA Y CAUSE UNDESIRED OPERA TION.
NOTE: NO CHANGES OR MODIFICA TIONS MA Y BE MADE TO THE
UNITS. ANY CHANGES MADE TO THE UNITS WILL VOID THE
USER'S AUTHORITY TO OPERA TE THE EQUIPMENT .

LIMITED 1-YEAR WARRANTY
Please visit www.x10.com/warranty
to complete your on-line warranty registration. Thank you.

For help or more information on setup, please visit:
www.x10.com/support

“Tilts” up and down.

Centers the camera.

“Pans” left and right.

Zooms out.
Stores Pan/Tilt

positions and Zoom
settings for each
camera (up to 9
settings).

Used to control the
diaphragm of the
camera. Iris Up gives
a brighter screen. Iris
Down gives a dimmer
screen.

Sweeps through the
stored positions for
the selected camera.

X10.com, a Div. of X10 Wireless Technology, Inc.
For additional help, visit www.x10.com/support

CR15A-03/03