Wyrestorm SP-0108-H2, SP-0104-H2 User Manual
1x4 or 1x8 4K HDMI Splitter
with HDCP 2.2 Encryption
SP-0104-H2 | SP-0108-H2
Quickstart Guide
Pure HDMI 1x4 or 1x8 splitter with support for full 4K resolutions and HDCP 2.2.
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
In the Box
1x SP-0104-H2 or SP-0108-H2 Splitter
1x 12V DC 1A Power Supply
1x 3-pin Screw Down Phoenix Connector
2x Mounting Brackets
1x Quickstart Guide
Basic Wiring Diagram
KEY
HDMI
Power
12V DC 1A
Power Supply
UHD Source
Additional Information
This Quickstart Guide provides the basic steps for the common uses of
this product. Refer to the Installation Guide and other documentation on
the product page for additional information.
Before Beginning
• WyreStorm recommends visiting the product page before installing
this product for updates to this Quickstart Guide as well as other
information about the product.
• Verify that all items are included in the packaging per the In the Box
list.
Installation
1. Connect an HDMI source to the HDMI In on the splitter using an
HDMI cable from a high quality brand such as WyreStorm Express.
2. Connect HDTV displays to Output 1 using an HDMI cable from a
high quality brand such as WyreStorm Express.
3. Repeat step 2 for additional displays or additional splitters.
4. Connect the included 12V DC 1A power supply to the DC 12V jack.
HDMI to
display
HDMI to
display
5. Congure EDIDs per the EDID Settings section.
HDMI to
UHD Display
UHD Display UHD Display
display
UHD Display
IMPORTANT!
Do not connect or disconnect (hot plug) the HDMI connections while
the splitter is powered on. Doing so may cause damage to the units or
connected devices.
Copyright © 2015 WyreStorm Technologies | wyrestorm.com
SP-0104-H2 | SP-0108-H2 Quickstart Guide | 151023
1 of 4
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
support@wyrestorm.com
Front Panel
Input LED
Output LEDs
Power LED
Rear Panel
Power In
HDMI Outputs
Input
EDID
RS-232
Solid: HDMI source is connected and powered On.
Off: HDMI source is not connected or is powered Off.
SP-0104-H2: 1-4 | SP-108-H2: 1-8
Solid: Display is connected and powered On.
Off: Display is not connected or is powered Off.
Solid: The splitter is powered On
Off: The splitter is powered Off
5.5mm Male Barrel Jack
Connect to the included 100~240V AC 50/60Hz power supply.
19-pin type A HDMI female:
SP-0104-H2: 1-4 | SP-108-H2: 1-8
Supports HDMI and DVI/D (requires adapter-not included). Limited to 600MHz pixel clock.
19-pin type A HDMI female:
Supports HDMI and DVI/D (requires adapter-not included). Limited to 600MHz pixel clock.
Rotary Dial
Used to set EDIDs to correct resolution conflicts between the source and the display.
See EDID Settings.
3-pin Screw Down Phoenix Connector
Used to update rmware on the SP-0104-H2. See RS-232 Wiring.
Copyright © 2015 WyreStorm Technologies | wyrestorm.com
SP-0104-H2 | SP-0108-H2 Quickstart Guide | 151023
2 of 4
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
support@wyrestorm.com
Loading...