Wyrestorm RX-70-4K-ARC Quick Start Manual

PDF provided by Conference Room AV

WyreStorm RX-70-4K-ARC 4K60 4:2:0 HDMI over HDBaseT Receiver w/ ARC

4K HDMI over HDBaseT™ Receiver

Key

Control System

IR RX
CAB-IR-LINK (Sold Separately)

with ARC (100m/328ft)

RX-70-4K-ARC

Quickstart Guide

Class A HDBaseT Receiver 4K over 70m/230ft with support for ARC or optical audio return.

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the installation

process.

In the Box

1x RX-70-4K-ARC Receiver
1x IR Emitter
1x Wide-band IR Receiver (30-50KHz)

Additional Information

This Quickstart Guide provides the basic steps for the common uses of
this product. Refer to the Installation Guide and other documentation on
the product page for additional information.

2x Mounting Brackets
1x 3-pin Phoenix Connector
1x Quickstart Guide (this document)

Before Beginning

• WyreStorm recommends visiting the product page before installing
this product for updates to this Quickstart Guide as well as other

Basic Wiring Diagram

information about the product.

• Verify that all items are included in the packaging per the In The Box
list.

Pre Wire

1. Run a Cat5e/6/6a cable from the transmitter location to the receiver

H2 Matrix with ARC

RX-70-4K-ARC

or

location no longer than 70m/230ft (4K) and 100m/328ft (1080p).
Terminate the cable per the HDMI/HDBaseT Wiring section.

2. (Optional) If using 3rd party IR emitters or connecting blocks at

either the transmitter or receiver, run the wire and terminate per the

IR TX (Emitter) Wiring section.

3. (Optional) If using RS-232 pass-through, run the wire and terminate

per the RS-232 Wiring section.

4. (Optional) If using 3rd party IR receivers at either the transmitter or

receiver, run the wire and terminate per the IR RX (Receiver) Wiring
section.

UHD Display

HDMI/Digital Video HDBaseT/Ethernet

IRDigital Audio

IMPORTANT!

Do not connect or disconnect (hot plug) the HDMI, or HDBaseT
connections while the transmitter or receiver is powered on. Doing so
may cause damage to the units or connected devices.

Recommended Products

To take full advantage of the features of this receiver, WyreStorm
recommends the following products be used within the system.

• MX-0606-HDBT-H2/MX-0808-HDBT-H2 Matrix Switcher – Certain
output cards on these switchers have an ARC function which is
supported by the RX-70-4K-ARC. Other receivers may not support
ARC.

• CAB-IR-LINK – Use this cable when using an IR control system for
matrix control of HDBaseT pass-through.

Copyright © 2015 WyreStorm Technologies | wyrestorm.com
RX-70-4K-ARC Quickstart Guide | 151217

Receiver Installation

1. Connect the HDMI Out on the receiver to an input on the display
using an HDMI cable from a high quality brand such as WyreStorm

Express.

2. Using the cable created in Pre Wire step 1, connect the 8-pin RJ-45
female plug to the HDBT In jack.

3. (Optional) Place an IR emitter onto the display device near the
device’s IR sensor and connect it the IR TX port.

4. (Optional) If using RS-232 pass-through, connect the 3-pin
connector to the RS-232 port on the receiver and the opposite end
to a port on the device being controlled.

5. (Optional) If using ARC using the display devices digital audio
output, connect a TOSLINK cable from the display device to the
S/PDIF In on the receiver.

6. If using ARC via HDMI or the audio inputs and outputs, see Audio

Return Input Settings for switch conguration.

1 of 4

North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343

[e-mail]