Wyrestorm NHD-100-TX v1, NHD-100-RX v2 Quick Start Manual
NetworkHD™ 100 Series AV Over IP H.264 Encoder/Decoder
NHD-100-TX v1 | NHD-100-RX v2
Quickstart Guide
IMPORTANT! Installation Requirements
WyreStorm Documentation and Firmware
Download the following items from the product page on WyreStorm.com.
They are essential for accurate conguration and use of the NetworkHD
system.
• Latest NetworkHD Firmware
• Management Suite v1.1.0 or Higher
• NetworkHD Installation Guide
• NetworkHD Switch Recommendations
• NetworkHD Switch Conguration Guides
• NetworkHD Switch Mapping Worksheet
• NetworkHD Touch Installation Guide
• NetworkHD Touch User Guide
• 3rd Party Control System Drivers
Installation and Conguration
• Verify that all NHD devices contain the latest version of rmware. This
will ensure that all devices are up to date and working at their highest
performance level.
• NetworkHD uses AutoIP to assign IP addresses in the range of
169.254.x.x out of the box. Set the PC being used for conguration to an
address in this range prior to starting the conguration process.
• WyreStorm recommends the use of the NHD-000-RACK for installations
containing multiple NetworkHD devices. Use of this product provides an
enclosure to mount and secure all NetworkHD devices in a rack.
Network Switch Requirements
• WyreStorm highly recommends the use of switches listed in the
NetworkHD Switch Recommendation Guide. These switches have been
veried by WyreStorm to meet the requirements of a NetworkHD system.
• NetworkHD requires a Layer 2 managed switch network with support for
Multicast & IGMP snooping enabled. Ensure that the switch being used
supports these features and that they are congured prior to connecting
the NetworkHD system.
• Congure all network switches to the exact specications contained in
the WyreStorm Switch Congurations Guides prior to connecting the
NetworkHD system. This will ensure proper operation from startup.
Copyright © 2017 WyreStorm Technologies | wyrestorm.com
NHD-100-TX v1 | NHD-100-RX v2 Quickstart Guide | 170630
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
support@wyrestorm.com
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the installation
process.
In The Box
1x NHD-100-TX or NHD-100-RX
1x 12v DC 1A. Power Supply
3x 3-pin Phoenix Connector
2x Mounting Ears
1x Quickstart Guide (This Document)
Basic Wiring Diagram
Wifi Router
Personal Computer
NHD-100-TX
NHD-100-TX
NHD-100-RX
iPad with
NetworkHD Touch
Satellite BoxSatellite Box
Blu-ray Player
NHD-000-CTL
Control System
Key
Digital Video/DVI/HDMI
Ethernet
NHD-100-TXNHD-100-TX
NHD-100-RX NHD-100-RX
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in this
entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.
IMPORTANT! Wiring Guidelines
• The use of patch panels, wall plates, cable extenders, kinks in cables, and
electrical or environmental interference will have an adverse effect on HDMI
and Ethernet transmission limiting performance. Steps should be taken to
minimize or remove these factors completely during installation for best
results.
• WyreStorm recommends using high quality HDMI cables such as
WyreStorm Express to ensure the highest content performance available.
• The type of category cable and length used can restrict the available video
resolution. While Cat5e can be used, WyreStorm recommends using Cat6
or higher to ensure the highest content performance available. See Video
Resolutions in the Specications table before determining cable type and
length.
HDMI Wiring
WyreStorm recommends using pre-terminated HDMI cables due to the
complexity of these connector types. Using pre-terminated cables will
ensure that these connections are accurate and will not interfere with the
performance of the product.
RS-232 Wiring
Most control systems and computers are DTE where pin 2 is RX, this can vary
from device to device. Refer to the documentation for the connected device for
pin functionally to ensure that the correct connections can be made.
1 2 3
Pin 1:
Pin 2:
TX (Transmit)
RX (Receive)
Pin 3: Ground (GND)
Audio Wiring
1 2 3
Pin 1:
Pin 2:
TX (Transmit)
RX (Receive)
Pin 3: Ground (GND)
Copyright © 2017 WyreStorm Technologies | wyrestorm.com
NHD-100-TX v1 | NHD-100-RX v2 Quickstart Guide | 170630
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
support@wyrestorm.com
2 of 4
Loading...